Sebring Convertible User Guide 2010
IMPORTANT: This User Guide is intended to familiarize you with the important features of your vehicle. The DVD enclosed contains your Owner’s Manual, Navigation Radio or Multimedia Radio Manual, Warranty Booklets, Tire Warranty and 24-Hour Towing Assistance (new vehicles purchased in the U.S.) or Roadside Assistance (new vehicles purchased in Canada) in electronic format. We hope you find it useful.
TABLE OF CONTENTS INTRODUCTION/WELCOME UTILITY WELCOME FROM CHRYSLER GROUP LLC . . . . . . . . . . . . . . . . 2 TRAILER TOWING WEIGHTS (MAXIMUM TRAILER WEIGHT RATINGS) . . . . . . . . . . . 38 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) . . . . . . . . . . 39 BRAKE/TRANSAXLE INTERLOCK MANUAL OVERRIDE . . . . . . . . . . 39 CONTROLS AT A GLANCE DRIVER COCKPIT . . . . . . . . . . . . . 4 INSTRUMENT CLUSTER . . . . . . . . . 6 GETTING STARTED KEY FOB . . . . . . . . . . . . . . THEFT ALARM . . . . . . .
INTRODUCTION/WELCOME WELCOME FROM CHRYSLER GROUP LLC Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This guide illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle.
INTRODUCTION/WELCOME CAUTION! Never park your vehicle over dry grass or other combustible materials. The heat from your vehicle exhaust system could cause a fire. CHRYSLER, DODGE, JEEP, ATF+4, MOPAR and Uconnect are registered trademarks of Chrysler Group LLC.
CONTROLS AT A GLANCE DRIVER COCKPIT 4
CONTROLS AT A GLANCE 5
CONTROLS AT A GLANCE INSTRUMENT CLUSTER Warning Lights - Low Fuel Warning Light - Charging System Light** - Oil Pressure Warning Light** - Anti-Lock Brake (ABS) Light** - Airbag Warning Light** - Electronic Throttle Control (ETC) Light - Tire Pressure Monitoring System (TPMS) Light - Engine Temperature Warning Light - Transmission Temperature Warning Light - Seat Belt Reminder Light BRAKE - Brake Warning Light** - Malfunction Indicator Light (MIL)** - Electronic Stability Control (ESC) Malfunction Indica
CONTROLS AT A GLANCE Indicators - Turn Signal Indicators - High Beam Indicator - Front Fog Light Indicator - Vehicle Security Indicator* - Cruise Indicator - Electronic Stability Control (ESC) Off Indicator - Position Light Indicator Odometer Messages door - Door Ajar deck - Trunk Ajar HOTOIL* - Transaxle Oil Temperature Exceeds Safe Threshold CHAngE OIL* - Change Engine Oil gASCAP - Fuel Cap Fault LoW TirE* - Low Tire Pressure TOP nOT SECUrE - Convertible Top Not Secure * If equipped ** Bulb Check with
GETTING STARTED KEY FOB Locking And Unlocking The Doors • Press the LOCK button once to lock all the doors. Press the UNLOCK button once to unlock the driver’s door only and twice within five seconds to unlock all the doors. • All doors can be programmed to unlock on the first press of the UNLOCK button. Refer to Programmable Features in this guide. WARNING! Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be injured.
GETTING STARTED WARNING! • Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Monoxide (CO) which is odorless and colorless. Carbon Monoxide is poisonous and can cause serious injury or death when inhaled. • Keep Key Fob transmitters away from children. Operation of the Remote Start System, windows, door locks or other controls could cause serious injury or death. Panic Alarm • Press the PANIC button once to turn the panic alarm on.
GETTING STARTED CHILD RESTRAINTS • Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. WARNING! • In a collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.
GETTING STARTED • Open the access port cover behind the seat where you are placing the child restraint. • Push the tether strap and hook through the access port and down into the trunk. NOTE: Route the tether strap to provide the most direct path from the child seat to the anchor. • From inside the trunk, open the access cover on the carpet covering the back of the seat and attach the tether strap hook to the anchor.
GETTING STARTED NOTE: The convertible top must be in the UP position to access the tether anchor. • Open the access port cover behind the seat where you are placing the child restraint. The access ports to the top tether anchorages are directly behind the seat headrests under a plastic cover. • Push the tether strap and hook through the access port and down into the trunk. NOTE: Route the tether strap to provide the most direct path from the child seat to the anchor.
GETTING STARTED Lumbar Support • The lumbar control lever is on the inboard side of the seatback. Rotate the lumbar lever downward to increase the lumbar support or upward to decrease the lumbar support as desired. Power Seat • The power seat switch, located on the outboard side of the seat near the floor, controls forward/back, up/down, and tilt adjustment. WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
GETTING STARTED Heated Seats • The controls for the front heated seats are located in the center console below the climate controls. • Press the switch once to select High-level heating. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off.
GETTING STARTED TILT / TELESCOPING STEERING COLUMN • The tilt/telescoping control lever is located below the steering wheel at the end of the steering column. • Push down on the lever to unlock the steering column. • To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. • Pull upward on the lever to lock the column firmly in place.
GETTING STARTED Unlock On First Press • To unlock either the driver’s side, or all doors, on the first press of the UNLOCK button: • Press and hold the LOCK button for at least 4 seconds, but no longer than 10 seconds. Then, press and hold the UNLOCK button while still holding the LOCK button. • Release both buttons at the same time. Auto Unlock Doors On Exit • To have all of the vehicle doors unlock when any door is opened: • Close all doors and place the key in the ignition.
OPERATING YOUR VEHICLE TURN SIGNAL/LIGHTS LEVER Headlights/Parking Lights/Automatic Headlights • Rotate the end of the lever to the first detent for parking lights , the second detent for headlights and the third detent for AUTO. • When set to AUTO, the system automatically turns the headlights on or off based on ambient light levels.
OPERATING YOUR VEHICLE WIPER/WASHER LEVER Front Wipers Intermittent, Low And High Operation • Rotate the end of the lever to the first detent position for one of five intermittent settings, the second for low wiper operation and the third detent for high wiper operation. Mist • Pull down on the lever and release when a single wipe is desired. Washer Operation • Pull the lever toward you and hold for as long as spray is desired.
OPERATING YOUR VEHICLE SPEED CONTROL LEVER Cruise ON/OFF • Push the ON/OFF button to activate the Speed Control. • CRUISE will appear on the instrument cluster to indicate the Speed Control is on. • Push the ON/OFF button a second time to turn the system off. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident.
OPERATING YOUR VEHICLE MANUAL CLIMATE CONTROLS Air Recirculation • Use recirculation for maximum A/C operation. • For window defogging, turn the recirculation button off. • Recirculation is not allowed in defrost, floor, defrost/floor (mix) modes. AUTOMATIC TEMPERATURE CONTROLS (ATC) Automatic Operation • Turn the Mode and Blower Controls to the AUTO position. • Select the desired temperature by rotating the Temperature Control. • The system will maintain the set temperature automatically.
OPERATING YOUR VEHICLE Air Conditioning • If the air conditioning button is pressed while in the AUTO mode, the indicator light may flash three times to indicate the cabin air is being controlled automatically. Air Recirculation • Use recirculation for maximum A/C operation. • For window defogging, turn the air recirculation button off. • If the recirculation button is pressed while in the AUTO mode, the indicator light may flash three times to indicate the cabin air is being controlled automatically.
OPERATING YOUR VEHICLE • The power top switch will operate when the ignition switch is turned to the ON or ACC position and when in the power accessory delay. Lowering • The power top switch is located on the instrument panel to the left of the steering column. • The power top switch has two top down positions which affect window position when lowering the top. • Press and hold the switch halfway down to the first detent position to lower the top and maintain the current window positions.
OPERATING YOUR VEHICLE Wind Stop • The Wind Stop installs in the backseat area of the vehicle. The Wind Stop will not interfere with power top operation. Therefore, it can remain installed when the top is up. However, when not in use, the Wind Stop folds to allow for convenient storage underneath the cargo shield in the trunk. WIND BUFFETING • Wind buffeting can be described as a helicopter-type percussion sound. If buffeting occurs with the rear windows open, adjust the front and rear windows together.
ELECTRONICS NON-TOUCH-SCREEN RADIOS Sales Code RES Sales Code RES/RSC 24
ELECTRONICS Sales Code REQ NOTE: Uconnect™ Phone and Voice Command are vehicle options which must be ordered separately. The buttons on the radio will only be active if the vehicle has been equipped with the option. • The radio sales code is located on the lower right side of the radio faceplate. • Unless otherwise noted, the information provided on the operation and functionality of the radios in this section is common to all non-touch-screen radios.
ELECTRONICS Clock Setting • Press and hold the TIME button until the hours blink; turn the TUNE/SCROLL control knob to set the hours. • Press the TUNE/SCROLL control knob until the minutes begin to blink; turn the TUNE/SCROLL control knob to set the minutes. • Press the TUNE/SCROLL control knob to save the time change. • To exit, press any button/knob or wait five seconds. Station Presets • Press the SET/RND button once and SET 1 will show in the display. Then select the button (1–6).
ELECTRONICS TOUCH-SCREEN RADIOS Navigation Radio – Sales Code RER Multimedia Radio – Sales Code REN 27
ELECTRONICS Multimedia Radio – Sales Code RBZ NOTE: Uconnect™ Phone and Voice Command are vehicle options which must be ordered separately. The buttons on the radio will only be active if the vehicle has been equipped with the option. • The radio sales code is located on the lower right side of the radio faceplate. • Unless otherwise noted, the information provided on the operation and functionality of the radios in this section is common to all touch-screen radios.
ELECTRONICS Auxiliary Mode • The auxiliary (AUX) jack allows a portable device, such as an MP3 player or a cassette player, to be plugged into the radio and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. • The display will switch automatically to the AUX mode when a 3.5 mm stereo mini-jack cable has been connected.
ELECTRONICS Copying From USB • Insert a USB device, then select MY MUSIC. • Touch the IMPORT MUSIC FILES soft-key, then touch the FROM USB soft-key in the next screen. • Select the folders or titles you would like to copy, then touch the DONE soft-key to start the copy process. Copy Pictures To The Hard-Drive • Insert either a CD or a USB device containing your pictures. • Touch the MY FILES soft-key, then go to the MANAGE MY FILES screen.
ELECTRONICS New Destination • Press the NAV hard-key to access the Navigation Main Menu. • Touch the NEW DESTINATION soft-key to program a destination, then select the destination soft-key of your choice. Program/Storing Home Address • Press the NAV hard-key to access the Navigation Main Menu. • Touch the GUIDE ME HOME soft-key, then touch the STREET ADDRESS soft-key. • Touch the STATE soft-key, then enter your state name into the speller; select your state from the list and press the CHANGE soft-key.
ELECTRONICS REMOTE AUDIO CONTROLS • The remote audio controls are located on the rear surface of the steering wheel. Right Switch • Press the switch up or down to increase or decrease the volume. • Press the button in the center to change modes AM/FM/CD/SAT. Left Switch • Press the switch up or down to search for the next listenable station or select the next or previous CD track. • Press the button in the center to select the next preset station (radio) or to change CDs if equipped with a CD Changer.
ELECTRONICS UNIVERSAL GARAGE DOOR OPENER Programming HomeLink® Begin Programming • The HomeLink® buttons are located in the sun visor. • Erase all channels before you begin training by holding the two outside buttons for up to 20 seconds until the red indicator flashes. • Park your vehicle outside of the garage and turn the ignition switch to the ON/RUN position. • Place the hand-held transmitter 1 to 3 in (3 to 8 cm) from the HomeLink® buttons while keeping the indicator light in view.
ELECTRONICS Programming A Rolling Code System • At the garage door opener motor (in the garage), locate the “learn” or “training” button. This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door). • Firmly press and release the “learn” or “training” button. The name and color of the button may vary by manufacturer.
ELECTRONICS WARNING! • Any voice commanded system should be used only in safe driving conditions following local laws and phone use. All attention should be kept on the roadway ahead. Failure to do so may result in an accident causing serious injury or death. • Your phone must be turned on and paired to the Uconnect™ Phone to allow use of this vehicle feature in emergency situations, when the cellular phone has network coverage and stays paired to the Uconnect™ Phone.
ELECTRONICS Receiving A Call – Accept (And End) • When an incoming call rings/is announced on Uconnect™, press the Phone . button • To end a call, press the Phone button . Mute (Or Unmute) Microphone During Call • During a call, press the Voice Command button . • (After the BEEP), say “mute on” (or “mute off”). Transfer Ongoing Call Between Handset And Vehicle • During a call, press the Voice Command button . • (After the BEEP), say “transfer call”.
ELECTRONICS WARNING! Any voice commanded system should be used only in safe driving conditions and all attention should be kept on the roadway ahead. Failure to do so may result in an accident causing serious injury or death. . After the NOTE: To access the tutorial, press the Voice Command button BEEP, say “tutorial”. Press any hard-key or touch the display to cancel the tutorial.
38 Towing a trailer with a larger than recommended frontal area could cause the engine to overheat or cause severe engine damage under extreme conditions. CAUTION! Enclosed trailers or open utility trailers with front shields/guards are not recommended for use with all four-cylinder and 2.7L engines with automatic transaxle. Please see your authorized dealer for additional information. 2 Max. Trailer Tongue Wt.
UTILITY • To operate the shift lock manual override, perform the following steps: RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) • Firmly apply the parking brake, insert the ignition Key Fob and rotate it to the ON position (do not start engine). Towing This Vehicle Behind Another Vehicle (Flat Towing With All Four Wheels On The Ground) • Remove the cup-holder liner. • Insert a key, screwdriver, or finger into the front hole, then push and hold the manual override release lever forward.
WHAT TO DO IN EMERGENCIES 24 HOUR TOWING ASSISTANCE - U.S. ONLY • Dial toll-free 1-800-521-2779. • Provide your name, vehicle identification number and license plate number. • Provide your location, including telephone number, from which you are calling. • Briefly describe the nature of the problem and answer a few simple questions. • You will be given the name of the service provider and an estimated time of arrival. If you feel you are in an “unsafe situation”, please let us know.
WHAT TO DO IN EMERGENCIES • Temperature changes can affect tire pressure, causing the TPMS light to turn on. Tire pressures will also increase as the vehicle is driven – this is normal and you should not adjust for this increased pressure. • Driving on under-inflated tires reduces your vehicle’s fuel efficiency and tire tread life. If a spare tire is in use on the vehicle, the TPMS light may turn on. - Engine Temperature Warning Light • This light warns of an overheated engine condition.
WHAT TO DO IN EMERGENCIES - Malfunction Indicator Light (MIL) • Certain conditions, such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the MIL after engine start. The vehicle should be serviced if the light stays on through several typical driving cycles. In most situations, the vehicle will drive normally and not require towing.
WHAT TO DO IN EMERGENCIES - Transmission Temperature Warning Light • This light indicates that there is excessive transmission fluid temperature that might occur with severe usage such as trailer towing. If this light turns on, stop the vehicle and run the engine at idle, with the transmission in NEUTRAL, until the light turns off. Once the light turns off, you may continue to drive normally.
WHAT TO DO IN EMERGENCIES IF YOUR ENGINE OVERHEATS • In any of the following situations, you can reduce the potential for overheating by taking the appropriate action. • On the highways — slow down. • In city traffic — while stopped, shift transmission into NEUTRAL, but do not increase engine idle speed. NOTE: There are steps that you can take to slow down an impending overheat condition: • If your air conditioner (A/C) is on, turn it off.
WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! • Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack.
WHAT TO DO IN EMERGENCIES Jack Location • The jack and jack-handle are stowed under the load floor in the trunk. Spare Tire Stowage • The compact spare tire is stowed under the rear load floor in the trunk. • To remove the spare tire, lift up the load floor cover and remove the hold down. Preparations For Jacking • Park on a firm, level surface. Avoid ice or slippery areas. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic.
WHAT TO DO IN EMERGENCIES • Block both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel. NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked.
WHAT TO DO IN EMERGENCIES • Place the jack underneath the lift area that is closest to the flat tire. Turn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill flange. • Raise the vehicle by turning the jack screw clockwise. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. WARNING! Raising the vehicle higher than necessary can make the vehicle less stable and cause an accident.
WHAT TO DO IN EMERGENCIES • Finish tightening the lug nuts. Push down on the wrench while tightening for increased leverage. Alternate nuts until each one has been tightened twice. The correct wheel nut tightness is 100 ft lbs (135 N•m). If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or at a service station. WARNING! A loose tire or jack, thrown forward in a collision or hard stop, could endanger the occupants of the vehicle.
WHAT TO DO IN EMERGENCIES JUMP-STARTING • If your vehicle has a discharged battery it can be jump-started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. • Jump-starting can be dangerous if done improperly so please follow the procedures in this section carefully. NOTE: When using a portable battery booster pack follow the manufacturer’s operating instructions and precautions.
WHAT TO DO IN EMERGENCIES Preparations for Jump-Start • The battery in your vehicle is located between the left front headlight assembly and the left front wheel splash shield. To allow jump-starting there are remote battery posts located on the left side of the engine compartment. WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades.
WHAT TO DO IN EMERGENCIES • Connect the negative end (-) of the jumper cable to the negative (-) post of the booster battery. • Connect the opposite end of the negative (-) jumper cable to the remote negative (-) post of the vehicle with the discharged battery. WARNING! Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury.
FWD With a Key FWD Without a Key Model Shift lever must be in NEUTRAL. The distance to be traveled must not exceed 15 mi (25 km), and the towing speed must not exceed 25 mph (40 km/h).
WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE • If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then move the shift lever back and forth between REVERSE and DRIVE. Using minimal accelerator pedal pressure to maintain the rocking motion, without spinning the wheels, is most effective.
WHAT TO DO IN EMERGENCIES EVENT DATA RECORDER (EDR) • This vehicle is equipped with an Event Data Recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed. The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.
MAINTAINING YOUR VEHICLE OPENING THE HOOD • Pull the release lever located below the instrument panel and in front of the driver’s door. • Raise the hood and locate the safety latch, in the middle of the hood opening. • Move the safety latch while lifting the hood at the same time. • Insert the support rod into the slot on the hood. • To close the hood, remove the support rod and place it in the retaining clip, then lower the hood slowly.
2.
2.
3.
MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Component Engine Coolant 2.4L Engine Coolant 2.7L Engine Coolant 3.5L Engine Oil with Filter 2.4L Engine Oil with Filter 2.7L Engine Oil with Filter 3.5L Fuel Selection 2.4L non Partial Zero Emissions Vehicle (PZEV), 2.7L, 3.5L Fuel Selection 2.4L PZEV Engine Oil Filter 2.4L, 2.7L, 3.5L Fluid, Lubricant, or Genuine Part MOPAR® Antifreeze/ Coolant Five Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent.
MAINTAINING YOUR VEHICLE Component Spark Plugs 2.4L except PZEV Spark Plugs 2.4L with PZEV Spark Plugs 2.7L Spark Plugs 3.5L Automatic Transaxle Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Capacities Genuine Part ZFR5F-11 (Gap 0.043 in — [1.11 mm]) ZFR5AP (Gap 0.031 in — [0.8 mm]) TE10PMC5 (Gap 0.050 in — [1.27 mm]) ZFR5LP-13G (Gap 0.050 in — [1.27 mm]) ® ® MOPAR ATF+4 Automatic Transmission — Fluid or equivalent ® licensed ATF+4 product.
12 12,000 18 24 30 36 42 48 54 60 66 72 78 18,000 24,000 30,000 36,000 42,000 48,000 54,000 60,000 66,000 72,000 78,000 X X X X Inspect the brake linings; replace if necessary. Inspect the CV joints. Perform the first inspection at 12,000 miles (20,000 km) or 12 months. Inspect the exhaust system. Perform the first inspection at 12,000 miles (20,000 km) or 12 months. 62 Replace the spark plugs (2.4L engine except PZEV).
MAINTAINING YOUR VEHICLE Maintenance Record Odometer Date Signature, Authorized Service Center 6,000 Miles (10,000 km) or 6 Months 12,000 Miles (20,000 km) or 12 Months 18,000 Miles (30,000 km) or 18 Months 24,000 Miles (40,000 km) or 24 Months 30,000 Miles (50,000 km) or 30 Months 36,000 Miles (60,000 km) or 36 Months 42,000 Miles (70,000 km) or 42 Months 48,000 Miles (80,000 km) or 48 Months 54,000 Miles (90,000 km) or 54 Months 60,000 Miles (100,000 km) or 60 Months 66,000 Miles (110,000 km) or 66 Mon
MAINTAINING YOUR VEHICLE FUSES Totally Integrated Power Module (TIPM) • The Totally Integrated Power Module (TIPM) is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses.
MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse 15 40 Amp Green Mini Fuse 16 15 Amp Lt. Blue 17 10 Amp Red 18 40 Amp Green 19 20 Amp Yellow 20 21 15 Amp Lt. Blue 10 Amp Red 22 10 Amp Red 23 15 Amp Lt. Blue 24 25 Amp Natural 25 10 Amp Red 26 15 Amp Lt.
MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse 34 30 Amp Pink 35 40 Amp Green 36 30 Amp Pink 37 Mini Fuse 25 Amp Natural Description Battery Feed — Anti-Lock Brakes (ABS) Module - if equipped/ Electronic Stability Program (ESC) Module - If Equipped Battery Feed — Anti-Lock Brakes (ABS) Module - If Equipped/ Electronic Stability Program (ESC) Module - If Equipped Battery Feed — Passenger Door Module (PDM)/Driver Door Module (DDM) Power Top Module (If Equipped) TIRE PRESSURES • Check the inflation
MAINTAINING YOUR VEHICLE WHEEL AND WHEEL TRIM CARE • All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. • To remove heavy soil and/or excessive brake dust, use MOPAR® Wheel Cleaner or equivalent or select a non-abrasive, non-acidic cleaner. CAUTION! Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner. These products may damage the wheels protective finish.
CONSUMER ASSISTANCE CHRYSLER GROUP LLC CUSTOMER CENTER WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. P.O.
CONSUMER ASSISTANCE In Canada NOTE: • The Owner’s Manual and User Guide electronic files are also available on the Chrysler, Jeep and Dodge websites. • Click on the “For Owners“ tab, select “Owner/Service Manuals“, then select your desired model year and vehicle from the drop down lists. • If you believe that your vehicle has a safety defect, you should contact the Customer Service Department immediately.
CONSUMER ASSISTANCE Disclaimer: WARNING! • THE TIRE MANUFACTURER’S LIMITED WARRANTY PROGRAM, THE DETAILS OF WHICH CAN BE FOUND, ON THE OWNERS MANUAL DVD, THE TIRE MANUFACTURER’S WEBSITE OR AT ANY AUTHORIZED SERVICE CENTER ARE IN LIEU OF ALL OTHER REMEDIES OR WARRANTIES, EXPRESS OR IMPLIED, ARISING BY LAW OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY.
CONSUMER ASSISTANCE Using Lift Kits WARNING! • Use of lift kits with some vehicle/tire combinations can cause instability or loss of control. When changing tire sizes, always consult an installer for optimum rim width and carefully check vehicle/tire clearances. Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident resulting in serious injury or death.
MOPAR ACCESSORIES MOPAR® ACCESSORIES • The following highlights just some of the authentic Chrysler Accessories by MOPAR® that have been engineered to customize your Chrysler Sebring. • To see the full line of accessories, stop by your Chrysler dealer or visit MOPAR.com.
NOTES 73
NOTES 74
This guide has been prepared to help you get quickly acquainted with your new Chrysler and to provide a convenient reference source for common questions. However, it is not a substitute for your Owner’s Manual. For complete operational instructions, maintenance procedures and important safety messages, please consult your Owner’s Manual, Navigation Radio User Manual, Multimedia User Manual and other Warning Labels in your vehicle. Not all features shown in this guide may apply to your vehicle.