2009 Sebring convertible Chrysler LLC 81-026-0936 First Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 1 CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . . 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 6 ..............
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is on the left front corner of the instrument panel.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . 19 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . 13 ▫ To Disarm The System . . . . . . . . . . . . . . . . . 19 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . 14 䡵 Illuminated Entry System — If Equipped . . . . . . 20 䡵 Sentry Key威 . . . . . . . . . . . . . . . . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Express Down Window Feature — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 25 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . 25 ▫ Programming Additional Transmitters . . . . . . 26 ▫ Battery Replacement . . . . . . . . . . . . . . . . . . . 26 ▫ General Information . . . . . . . . . . . . . . . . . . . 27 䡵 Remote Starting System — If Equipped . . . . . . . 28 ▫ How To Use Remote Start . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Driver And Front Passenger Supplemental Restraint System (SRS) - Airbag . . . . . . . . . . . 48 ▫ Event Data Recorder (EDR) . . . . . . . . . . . . . . 60 ▫ Child Restraints . . . . . . . . . . . . . . . . . . . . . . 62 䡵 Engine Break-In Recommendations . . . . . . . . . . 72 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 ▫ Transporting Passengers . . . . . . . . . . . . . . . . 73 ▫ Lock Your Vehicle . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your authorized dealer. Ask your authorized dealer for these numbers and keep them in a safe place. You can insert the double-sided keys into the locks with either side up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Ignition Key Removal Place the shift lever in PARK. Turn the ignition switch to the ACC position, push the key slightly inward, rotate the key to the LOCK position, and remove the key. Ignition Switch Positions 1 — LOCK 2 — ACC (ACCESSORY) 3 — ON 4 — START NOTE: • If you try to remove the key before you place the shift lever into PARK, the key may become trapped temporarily in the ignition switch lock cylinder.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles equipped with the Electronic Vehicle Information Center (EVIC), the power window switches, radio, hands–free system (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned to the LOCK position. Opening either door will cancel this feature. The time for this feature is programmable.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 SENTRY KEY姞 The Sentry Key威 Immobilizer System prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses ignition keys, which have an embedded electronic chip (transponder), to prevent unauthorized vehicle operation.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • The Sentry Key威 Immobilizer System is not compatible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Sentry Key姞 Programming You can program new keys to the system if you have two valid Sentry Keys威 by performing the following procedure: 1. Cut the additional Sentry Key威 Transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the ignition switch. Turn the ignition switch to the ON position for at least three seconds, but no longer than 15 seconds.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If a programmed key is lost, see your authorized dealer to have all remaining keys erased from the systems memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of service to be reprogrammed. General Information The Sentry Key威 system complies with FCC rules part 15 and with RSS-210 of Industry Canada.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 To Arm The System: 1. Remove the keys from the ignition switch and get out of the vehicle. 2. Lock the door using either the power door lock switch (one door must be open) or the LOCK button on the Remote Keyless Entry (RKE) transmitter (doors can be open or closed), and close all doors. NOTE: The system will not arm if you lock the doors with the manual door lock plungers. 3.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • The driver’s door key cylinder and the trunk button on the RKE transmitter cannot arm or disarm the system. armed when the battery is reconnected. The exterior lights will flash, and the horn will sound. If this occurs, disarm the system. • The system remains armed during trunk entry. Pressing the trunk button will not disarm the system. If someone enters the vehicle through the trunk and opens any door, the alarm will sound.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 The interior lights will fade to off after about 30 seconds or they will immediately fade to off once the ignition switch is turned ON. NOTE: • The line of transmission must not be blocked with metal objects when using the RKE transmitter. NOTE: • The illuminated entry system will not operate the interior lights if the dimmer control is in the “defeat” position (extreme downward position).
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Unlock the Doors Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door, or twice to unlock both doors. The turn signal lights will flash to acknowledge the unlock signal. The Illuminated Entry system (if equipped) will also turn on.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Vehicle Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Vehicle Security Alarm System. Flash Lights with Lock The feature will cause the turn signal lights to flash when the doors are locked or unlocked with the RKE transmitter. This feature can be turned on or turned off.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Illuminated Approach — If Equipped This feature activates the headlights for up to 90 seconds when the doors are unlocked with the RKE transmitter. The time for this feature is programmable on vehicles equipped with the Electronic Vehicle Information Center (EVIC). For details, refer to “Illuminated Approach,” under “Personal Settings (Customer-Programmable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 2. Release both buttons at the same time. 3. Test the feature while outside of the vehicle, by pressing the LOCK button on the RKE transmitter with the ignition in the LOCK position, and the key removed. 4. Repeat these steps if you want to return this feature to its previous setting. NOTE: Pressing the LOCK button on the RKE transmitter while you are in the vehicle will activate the Vehicle Security Alarm.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Panic Alarm will stay on for three minutes unless you turn it off by pressing the PANIC button a second time or if the vehicle speed is 5 mph (8 km/h) or greater. NOTE: You may need to be close to the vehicle when using the RKE transmitter to turn off the Panic Alarm due to the Radio Frequency (RF) noises emitted by the system. • Do not touch the battery terminals that are on the back housing or the printed circuit board. 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To assemble the RKE transmitter case, snap the two halves together. General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE STARTING SYSTEM — IF EQUIPPED This system uses the Remote Keyless Entry (RKE) transmitter to start the engine conveniently from outside the vehicle while still maintaining security. The system has a targeted range up to 328 ft (100 m). NOTE: The vehicle must be equipped with an automatic transaxle to be equipped with Remote Start.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 To Enter Remote Start Mode Press and release the REMOTE START button on the RKE transmitter twice. The engine will start and the vehicle will remain in the Remote Start mode for a 15 minute cycle. NOTE: • For security, power window operation is disabled when the vehicle is in the Remote Start mode. • The engine can be started two consecutive times (two 15 minute cycles) with the RKE transmitter.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS WARNING! (Continued) Manual Door Locks To lock each door, push the door lock plunger on each door trim panel downward. To unlock each door, pull the door lock plunger on each door trim panel upward. If the door lock plunger is down when you shut the door, the door will lock. Make sure the keys are not inside the vehicle before closing the door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Power Door Locks A door lock switch is located on the driver and passenger door trim panel. Press this switch to lock or unlock the doors. Automatic Door Locks When enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). The Automatic Door Locks feature can be enabled or disabled by your authorized dealer. See your authorized dealer for programming.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Unlock Doors on Exit Programming The Automatic Unlock Doors on Exit feature can be enabled or disabled as follows: • For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to “Personal Settings (Customer-Programmable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual for details. 3. Depress the power door UNLOCK switch to unlock the doors. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WINDOWS Power Windows The window controls on the driver’s door trim panel operate the door windows and the rear quarter windows. The window controls will operate when the ignition switch is turned to the ON or ACC position, and when the accessory delay feature is active. NOTE: • If a fluttering noise is heard from the rear seat belts while driving with the windows down, safely bring the vehicle to a stop and buckle the rear seat belts over the empty seats.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Smart Glass Feature — Convertible only The door window will lower slightly if the window is fully up when opening the door. The window will return to its full up position after closing the door. This action allows the door to open without resistance and prevents window and top seal damage. Auto Window Down — If Equipped The front window controls on the driver and passenger door trim panels have an Auto Down feature.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 To reactivate the window Smart Glass Feature, perform the following steps after vehicle power is restored. 1. Lowering all four windows to the full open position. button (setting it in the down position). To enable the window control, press and release the window LOCK button again (setting it in the up position). 2. Press and hold the Power Top Switch in the Close direction. Once the Power Top becomes fully closed, all four windows will start closing. 3.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with one window down in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with one window open, then open both windows together to minimize the buffeting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 With the ignition ON, the word “deck” will display in the odometer indicating the trunk is open. The odometer display will reappear once the trunk is closed or if the trip button is pressed. With the key in the LOCK position or with the key out, the word “deck” will display until the trunk is closed. On vehicles equipped with the Electronic Vehicle Information Center (EVIC), the words “Trunk Ajar” will display.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Trunk Internal Emergency Release As a security measure, a Trunk Internal Emergency Release lever is built into the trunk latching mechanism. In the event of an individual being locked inside the trunk, the trunk can be simply opened by pulling on the glow-in-the-dark handle attached to the trunk latching mechanism. OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 • Supplemental front seat side mounted head airbags • Front seat belt retractors that incorporate pretensioners to enhance occupant protection by managing occupant energy during an impact event • All seat belt systems (except the driver’s) include Automatic Locking Retractors (ALRs), which lock the seat belt webbing into position by extending the belt all the way out and then adjusting the belt to the desired length to restrain a child seat or secure a large i
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 WARNING! (Continued) • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too. • Two people should never be belted into a single seat belt. People belted together can crash into one another in an accident, hurting one another badly.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Inserting Latch Plate into Buckle WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 WARNING! (Continued) • A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision, it could even cut into you. Be sure the belt is straight.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. in a collision. Pretensioners work for all size occupants, including those in child restraints.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Reminder System (BeltAlert姞) If the occupied driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert威) will alert the driver to buckle their seat belt. The driver should also instruct all other occupants to buckle their seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have successfully completed the programming. BeltAlert威 can be reactivated by repeating this procedure. NOTE: Although BeltAlert威 is deactivated, the Seat Belt Warning Light will continue to illuminate as long as the driver’s seat belt is unbuckled. Automatic Locking Mode In this mode, the shoulder belt is automatically prelocked.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 The front airbags have a dual-stage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size. WARNING! Front Airbag Components 1 — Driver Airbag 2 — Passenger Airbag 3 — Knee Bolster NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. • Do not put anything on or around the front airbag covers or attempt to open them manually.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not attach cup holders or any other objects on or around the door. The inflating seat airbag could drive the object into occupants, causing serious injury. • Do not drill, cut or tamper with the knee bolster in any way. • Do not mount any accessories to the knee bolster such as alarm lights, stereos, citizens band radios etc. collisions, both the front and seat airbags may be triggered.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 restraints or belt-positioning booster seats. Older children who do not use child restraints or belt-positioning booster seats should ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm. If a child from 1 to 12 years old must ride in the front passenger seat because the vehicle is crowded, move the seat as far back as possible, and use the proper child restraint.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Being too close to the steering wheel or instrument panel during front airbag deployment could cause serious injury. Airbags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • Seat airbags also need room to inflate. Do not lean against the door. Sit upright in the center of the seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 The first stage inflator is triggered immediately during an impact that requires airbag deployment. The timing of the second stage determines whether the output force is low, medium, or high. If a low output is sufficient to meet the need, the second stage is expended later in the crash event. • Driver Airbag Special Features Driver airbag deployment and force level is controlled by the driver’s seat position as well as impact severity.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or ON position. These include all of the items listed above except the steering wheel and column, instrument panel, and passenger knee bolsters. If the key is in the LOCK position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 • Impact Sensors Two sensors, located on the front body structure, trigger airbag deployment in direct frontal impacts and aid the ORC in determining appropriate response to frontal impact events. Additional sensors in the ORC determine the level of airbag deployment and provide verification.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When the bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each bag deploys independently, that is a left side impact deploys the left bag only and a right-side impact deploys only the right bag. The following requirements must be strictly adhered to: • Do not make any modifications to the front seat components, assembly, or to the seat cover in any way.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 If A Deployment Occurs The airbag systems are designed to deploy when the Occupant Restraint Controller (ORC) detects a moderateto-severe collision, to help restrain the driver and front passenger, and then immediately deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioners, and the front passenger seat belt retractor assembly, replaced by an authorized dealer as soon as possible. Also, have the Occupant Restraint Controller System serviced as well.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 WARNING! (Continued) • It is dangerous to try to repair any part of the airbag system yourself. Be sure to tell anyone who works on your vehicle that it has an airbag system. • Do not attempt to modify any part of your advanced airbag system. The airbag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any advanced airbag system service.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the ORC may also be disabled. The airbags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. For fuse location information, refer to “Fuses” under “Maintenance Procedures” in section 7 of this manual. See your authorized dealer for service.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 In the event that an investigation is undertaken by Chrysler LLC (regardless of initiative), the company or its designated representative will first obtain permission of the appropriate custodial entity for the vehicle (usually the vehicle owner or lessee) before accessing the electronic data stored, unless ordered to download data by a court with legal jurisdiction (i.e., pursuant to a warrant).
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Airbag deployment level (if applicable) • Impact acceleration and angle • Seat belt status • Brake status (service and parking brakes) • Accelerator status (including vehicle speed) • Engine control status (including engine speed) • Transaxle gear selection • Cruise control status • Traction/stability control status • Tire Pressure Monitoring System status (if equipped) Child Restraints Everyone in your vehicle needs to be buckled up all the time, including
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to ensure you have the correct seat for your child. Use the restraint that is correct for your child. Infants and Child Restraints • Safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg).
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year. These child seats are also held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system. Refer to “LATCH — Child Seat Anchorage System (Lower Anchors and Tether for CHildren)” in this section.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward facing child restraint should only be used in a rear seat.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • All passenger seating positions contain automatic locking retractors. However, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary. • Buckle the child into the seat according to the child restraint manufacturer’s directions. CAUTION! When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Do not leave it loose in the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 to the top tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products. Tether anchorage kits are also available for most older vehicles.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remind all children in the vehicle that the seat belts are not toys and should not be played with, and never leave your child unattended in the vehicle. Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 seat cover material. Then rotate the tether anchorage cover directly behind the seat where you are placing the child restraint and attach the tether strap to the anchorage, being careful to route the tether strap to provide the most direct path between the anchor and the child restraint.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The seat belt must be in the Automatic Locking mode in order to enable a child restraint to be tightly installed. Refer to “Automatic Locking Mode” in this section for details. A locking clip should not be necessary once the automatic locking feature is enabled. Position the shoulder and lap belt on the child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 4. Open the access cover (C) on the carpet covering the back of the seat and attach the tether strap hook (D) to the anchor. Child Tether Access Port Cover 3. Push the tether strap and hook (B) through the access port and down into the trunk. NOTE: Route the tether strap to provide the most direct path from the child seat to the anchor. Child Tether Anchor 5. Remove slack in the tether strap according to the child restraint manufacturer’s instructions.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 shown under “Engine Oil”, under “Maintenance Procedures” in section 7 of this manual. NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED. A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty. SAFETY TIPS Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas WARNING! • Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO), follow these safety tips: Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Safety Checks You Should Make Inside the Vehicle Seat Belts Inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (i.e., bent retractor, torn webbing, etc.).
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lights Have someone observe the operation of exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. Door Latches Check for positive closing, latching, and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Convertible Top Operation . . . . . . . . . . . . . . . . 81 ▫ Power Convertible Top Usage Precautions . . . . 82 ▫ Cargo Shield . . . . . . . . . . . . . . . . . . . . . . . . 86 ▫ Power Convertible Top Controls . . . . . . . . . . . 87 ▫ Lowering The Power Convertible Top . . . . . . . 88 ▫ Raising The Power Convertible Top . . . . . . . . 89 ▫ Manual Bypass Mode . . . . . . . . . . . . . . . . . . 90 ▫ Wind Stop — If Equipped . . . . . . . . . . . . .
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Hands-Free Communication (UConnect威) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 102 ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . 104 ▫ Phone Call Features . . . . . . . . . . . . . . . . . . 112 ▫ UConnect威 System Features . . . . . . . . . . . . . 115 ▫ Advanced Phone Connectivity . . . . . . . . . . . 120 ▫ Things You Should Know About Your UConnect威 System . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 ▫ Headlights With Wipers (Available With Auto Headlights Only) . . . . . . . . . . . . . . . . 144 ▫ Headlights With Wipers (Available With Auto Headlights Only) . . . . . . . . . . . . . . . . 153 ▫ Headlight Time Delay — If Equipped . . . . . . 145 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . 153 ▫ Daytime Running Lights (DRL) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 145 䡵 Tilt/Telescoping Steering Column . . . . . . . .
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Gate Operator/Canadian Programming . . . . 162 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 ▫ Troubleshooting Tips . . . . . . . . . . . . . . . . . . 163 ▫ General Information . . . . . . . . . . . . . . . . . . 164 䡵 Electrical Power Outlets . . . . . . . . . . . . . . . . . 164 ▫ Heated Or Cooled Cupholder — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 168 ▫ Rear Seat Cupholders . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 CONVERTIBLE TOP OPERATION WARNING! The convertible top does not provide the structural protection that a reinforced metal roof does and the fabric top cannot be expected to prevent the ejection of the occupants of a vehicle in a collision. Therefore, it is important that all occupants wear their seat belts at all times when riding in a convertible.
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To complete either operation, the trunk lid returns to its normal position and then latches. Spring-loaded flipper doors, which provide clearance for the linkage, close off notches in the quarter trim panels when the top is up. Power Convertible Top Usage Precautions NOTE: • The convertible top will not operate unless the vehicle is stationary, the cargo shield is positioned correctly, and the trunk lid is closed and latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 CAUTION! (Continued) CAUTION! (Continued) • Always place items carefully into the trunk. • Do not push items too far into the trunk, particularly when the top is retracted into its stowage area in the trunk. • Do not use the area near the tonneau cover for storage. Failure to follow these cautions can cause damage to the convertible top components, trunk contents, and the vehicle interior. • Make sure the ambient temperature is above 0°F (-18°C).
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) CAUTION! (Continued) Failure to follow these cautions can cause damage to the convertible top components, trunk contents, and the vehicle interior. • Always use a normal ice scraper to remove snow or ice from the rear window. Use of a sharp object or other tools could scratch the fabric or panels when removing snow or ice.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 WARNING! WARNING! (Continued) • Before operating the power top, make sure that no moving parts of the convertible top can injure a person or animal. • Never place any extremities (hands, feet, etc.) near the convertible top components, the upper windshield area, the shelf area behind the rear seats, or the convertible top stowage area while raising or lowering the convertible top.
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Shield The cargo shield is located in the trunk. Before lowering the convertible top, you must unfold the cargo shield and seat the tabs at each end of the cargo shield in the V slots in the trunk liner. Doing so closes a switch that allows top operation. If the switch is not closed, a warning message displays in the instrument cluster to notify the driver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 panel forward onto the horizontal panel, then grasp both panels and lift them to the forward, upright position in the trunk. Power Convertible Top Controls The power top switch is located on the instrument panel to the left of the steering column. 3 Stowed Cargo Shield NOTE: The convertible top will NOT operate with the Cargo Shield in the stowed position.
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE There is also a power top button on the Remote Keyless Entry (RKE) transmitter for remotely lowering the power convertible top. Lowering the Power Convertible Top Using the Power Top Switch NOTE: The power top switch will operate when the ignition switch is turned to the ON or ACC position and when in the power accessory delay. There are two Top Down switch positions. Press the switch to the first detent and release it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 Using the Remote Keyless Entry (RKE) Transmitter NOTE: Steps 1 – 3 must be performed within five seconds. 1. Press and release the UNLOCK button on the RKE transmitter. 2. Press and release the POWER TOP button on the RKE transmitter. 3. Press and hold the POWER TOP button until the Power Top and All Windows Down feature is complete.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Read all of the Notes, Cautions, and Warning found under “Power Convertible Top Usage Precautions” to verify all operating conditions are met. 2. Check for Operation and Warning Messages as described under “Power Convertible Top Operation & Warning Messages.” If applicable, perform the related action to correct the condition present. 3. If Steps 1 and 2 do not resolve the problem, see “Manual Bypass Mode” Section.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 3. Lay the small frame (1) flat on top of the large frame (2) and snap the two frames together by engaging the frame lock (3). NOTE: The frames must lie flat on each other in order to snap them together. 4. Pivot the small frame (1) away from the large frame (2) until the pivot lock (3) engages to lock the two frames in an L shape.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Unfold both stems at the rear of the large frame. 6. Align and insert the stems into the slot in each trim panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 7. Align the pins at the front of the large frame with the hole in each trim panel. Slide the pins outward until fully extended into each hole. Removing and Storing the Wind Stop Reverse the installation procedure to remove, fold, and store the Wind Stop. However, note the following before doing so: • Disengage the pivot lock (1) to fold the small frame flat onto the large frame. Disengage the frame lock (2) to disconnect the small frame from the large frame.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Convertible Top Operation and Warning Messages When the appropriate conditions exist, the PTCM displays various power convertible top operation and warning messages in the Electronic Vehicle Information Center EVIC Message〫 EVIC Message Display Time〫 CONVERTIBLE TOP IN OPERATION CONVERTIBLE TOP COMPLETE Until Operation is Complete 9 Seconds Odometer Message (< 5 mph [8 km/h]) 〫〫 TOP Odometer Message Display Time〫〫 Until Operation is Complete (EVIC)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 EVIC Message〫 EVIC Message Display Time〫 SECURE CARGO SHIELD 9 Seconds CONVERT- Until OpIBLE TOP eration is IN OPERA- Complete TION Odometer Message (< 5 mph [8 km/h]) 〫〫 SET CARGO SHIELD Odometer Message Display Time〫〫 TOP Until Operation is Complete Display Scrolls for 9 Seconds Odometer Message (> 5 mph [8 km/h]) 〫〫 — Odometer Message Display Time〫〫 Chime Condition Operator Action Required — Single Chime The Top Fails to Move When Operating
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE EVIC Message〫 EVIC Message Display Time〫 SPEED 9 Seconds TOO HIGH TRUNK AJAR Odometer Message (< 5 mph [8 km/h]) 〫〫 SPEED TOO HIGH Continuous DECK Odometer Message Display Time〫〫 Display Scrolls for 9 Seconds Odometer Message (> 5 mph [8 km/h]) 〫〫 TOP Continuous DECK Odometer Message Display Time〫〫 Chime Condition Operator Action Required 6 Seconds Single Chime You Are Operating the Power Top at a Vehicle Speed Greater Than 0 mph (0 km/h) The Tru
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 EVIC Message〫 EVIC Message Display Time〫 CONVERT- 6 Seconds IBLE TOP MALFUNCTION CONVERTIBLE TOP MALFUNCTION Odometer Message (< 5 mph [8 km/h]) 〫〫 TOP FAIL Until Fault TOP FAIL is No Longer Detected or Repaired Odometer Message Display Time〫〫 Display Scrolls for 6 Seconds Odometer Message (> 5 mph [8 km/h]) 〫〫 TOP Display TOP Scrolls until Fault is No Longer Detected or Repaired 〫 If so equipped. 〫〫 For vehicles not equipped with the EVIC.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 〫〫〫 The PTCM will lockout the power convertible top system if the vehicle charging system is malfunctioning, or the battery is run down, or the hydraulic pump is overheating. In addition, the system prohibits lowering the top when ambient temperature is at 0°F (-18°C) or lower and raising the top when ambient temperature is below -40°F (-40°C).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 MIRRORS Automatic Dimming Mirror This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light will illuminate to indicate when the dimming feature is activated.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 3 Power Mirror Adjust Switch Mirror Directions After selecting a mirror, move the knob in the same direction you want the mirror to move. When finished, return the knob to the center “O” (Off) position to guard against accidentally moving a mirror position. Heated Power Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the Rear Window Defroster.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vanity Mirror — If Equipped A vanity mirror is attached to the inside face of the sun visor. To use the mirror, rotate the sun visor downward. HANDS-FREE COMMUNICATION (UConnect姞) — IF EQUIPPED NOTE: The sales code RER and REU radios contain an integrated Hands-Free Communication (UConnect威) system. Refer to your “Navigation User’s Manual” for UConnect威 system operating instructions for these radios.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 UConnect威 allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. The UConnect威 system is driven through your Bluetooth威 “Hands-Free Profile” cellular phone.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect威 system is fully integrated with the vehicle’s audio system. The volume of the UConnect威 system can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the UConnect威 system such as ⬙CELL⬙ or caller ID on certain radios.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Help Command If you need assistance at any prompt, or if you want to know your options at any prompt, say ⬙Help⬙ following the beep. The UConnect威 system will play all the options at any prompt if you ask for help. To activate the UConnect威 system from idle, simply press the PHONE button and follow the audible prompts for directions. All UConnect威 system sessions begin with a press of the PHONE button on the radio control head.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For identification purposes, you will be prompted to give the UConnect威 system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • You will then be asked to give your cellular phone a priority level between one and seven, with one being the highest priority. You can pair up to seven cellular phones to your UConnect威 system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 • The system will prompt you to say the name of the person you want to call. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook New Entry.⬙ • After the ⬙Ready⬙ prompt and the following beep, say the name of the person you want to call. For example, you can say ⬙John Doe,⬙ where John Doe is a previously stored name entry in the UConnect威 phonebook or downloaded phonebook.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect威 system will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language. In addition, if equipped and supported by your phone, UConnect威 automatically downloads your mobile phone’s phonebook.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 • This downloaded phonebook cannot be edited or deleted on the UConnect威. These can only be edited on the mobile phone. The changes are transferred and updated to UConnect威 on the next phone connection. Phonebook Download — Single Entry If equipped and supported by your phone, UConnect威 allows the user to download entries from their phone via Bluetooth威. To use this feature, press the PHONE button and say “Phonebook Download.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Edit.⬙ • You will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, mobile, or pager) that you wish to edit. mobile and a home number, but you can add ”John Doe’s” work number later using the ⬙Phonebook Edit⬙ feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 from the list, press the VOICE RECOGNITION button while the UConnect威 system is playing the desired entry and say ⬙Delete.⬙ • After you enter the name, the UConnect威 system will ask you which designation you wish to delete: home, work, mobile, pager, or all. Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To call one of the names in the list, press the VOICE RECOGNITION button during the playing of the desired name, and say ⬙Call.⬙ NOTE: The user can also exercise ⬙Edit⬙ or ⬙Delete⬙ operations at this point. • The UConnect威 system will then prompt you as to the number designation you wish to call. • The selected number will be dialed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 NOTE: The UConnect威 system compatible phones in the market today do not support rejecting an incoming call when another call is in progress. Therefore, the user can only answer an incoming call or ignore it. Making a Second Call While Current Call is in Progress To make a second call while you are currently on a call, press the VOICE RECOGNITION button and say ⬙Dial⬙ or ⬙Call⬙ followed by the phone number or phonebook entry you wish to call.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Three-Way Calling To initiate three-way calling, press the VOICE RECOGNITION button while a call is in progress, and make a second phone call, as described under ⬙Making a Second Call While Current Call is in Progress.⬙ After the second call has established, press and hold the PHONE button until you hear a double beep, indicating that the two calls have been joined into one conference call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 • After the ignition key is switched to OFF, a call can continue on the UConnect威 system for a certain duration, after which the call is automatically transferred from the UConnect威 system to the mobile phone. • An active call is automatically transferred to the mobile phone after the ignition key is switched to OFF. UConnect姞 System Features Language Selection To change the language that the UConnect威 system is using: • Press the PHONE button to begin.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt and the following beep, say ⬙Emergency⬙ and the UConnect威 system will instruct the paired cellular phone to call the emergency number. This feature is supported in the U.S., Canada, and Mexico. NOTE: • The emergency number dialed is based on the country where the vehicle is purchased (911 for the U.S. and Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 NOTE: • The towing assistance number dialed is based on the country where the vehicle is purchased (1-800-5282069 for the U.S., 1-877-213-4525 for Canada, 55-143454 for Mexico City and 1-800-712-3040 for outside Mexico City in Mexico). • If supported, this number may be programmable on some systems. To do this, press the PHONE button and say “Setup”’, followed by “Towing Assistance”. Paging To learn how to page, refer to ⬙Working with Automated Systems.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE or sequence of numbers, followed by ⬙Send,⬙ is also to be used for navigating through an automated customer service center menu structure, and to leave a number on a pager. You can also send stored UConnect威 phonebook entries as tones for fast and easy access to voice mail and pager entries. To use this feature, dial the number you wish to call and then press the VOICE RECOGNITION button and say, “Send.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Confirmations.⬙ The UConnect威 system will play the current confirmation prompt status and you will be given the choice to change it.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Following the beep, say ⬙Mute off.⬙ If you would like to connect or disconnect the Bluetooth威 connection between a UConnect威 paired cellular phone and the UConnect威 system, follow the instructions described in your cellular phone User’s Manual.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Select Another Cellular Phone This feature allows you to select and start using another phone paired with the UConnect威 system. • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Select Phone⬙ and follow the prompts. • You can also press the VOICE RECOGNITION button at any time while the list is being played, and then choose the phone that you wish to select.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Training For users experiencing difficulty with the system recognizing their voice commands or numbers, the UConnect威 system Voice Training feature may be used. To enter this training mode, follow one of the two following procedures: From outside the UConnect威 mode (e.g.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English, French, and Spanish accents, the system may not always work for some. • When navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say ⬙Send.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. • Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the UConnect威 system. • Echo at the far end can sometimes be reduced by lowering the in-vehicle audio volume.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 3
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 3
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call UConnect威 Tutorial try again voice training work yes 3
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 When you press the VR hard-key, you will hear a beep. The beep is your signal to give a command. NOTE: If you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the VR hard-key, listen for the beep, and say your command. Pressing the VR hard-key while the system is speaking is known as “barging in.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Commands The Voice Recognition system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the Volume 1. Start a dialogue by pressing the VR hard-key. 2. Say a command (e.g., “Help”). 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the Voice Recognition system is speaking.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Radio FM To switch to the FM band say “FM” or “Radio FM”.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Memo To switch to the voice recorder mode say “Memo”. In this mode, you may say the following commands: • “New Memo” (to record a new memo) — During the recording you may press the VR hard-key to stop recording. You proceed by saying one of the following commands: − “Previous” (to play the previous memo) − “Delete” (to delete a memo) • “Delete All” (to delete all memos) System Setup To switch to system setup say “Setup”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Voice Training For users experiencing difficulty with the system recognizing their voice commands or numbers, the UConnect威 system Voice Training feature may be used. 1. Press the VR hard-key, say “System Setup” and once you are in that menu then say “Voice Training.” This will train your own voice to the system and will improve recognition. SEATS Power Seats The power seat switch is on the outboard side of the seat near the floor.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under any seat as it may cause damage to the seat controls. WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 WARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods. Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Recliner Adjustment The recliner control is on the outboard side of the seat. To recline the seat, lean forward slightly and lift the lever. Then lean back to the position desired and release the lever. To return the seatback to its normal upright position, lean forward and lift the lever. Release the lever once the seatback is in the upright position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Easy Entry System The Easy Entry lever is located on upper seat belt anchor cover. On the passenger seat, pull the lever upward to move the seat and seatback forward. When returning the seat to its normal position, the memory feature restores the seat position and seatback recline position to their current settings. On the driver seat, pull the lever upward to move the seatback forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjust the restraint so that the upper edge is as high as practical. To raise it, pull upward on the head restraint. To lower it, depress the button on the post guide and push downward on the head restraint.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD Two latches must be released to open the hood. 1. Pull the hood release lever located under the left side of the instrument panel. 2. Move to the outside of the vehicle and lift the secondary latch underneath the center front edge of the hood. Then, raise the hood.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole on the underside of the hood. slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights And Parking Lights Turn the end of the multifunction lever to the first detent for parking light operation. Turn the end of the lever to the second detent for headlight operation. Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, turn the end of the multifunction lever to the AUTO position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 In addition, the headlights will turn off when the wipers are turned off if they were turned on by this feature. If you turn the headlights, parking lights, or ignition switch ON again, the system will cancel the delay. The Headlights with Wipers feature can be turned on or off through the Electronic Vehicle Information Center (EVIC) — if equipped.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Daytime Running Lights will turn off automatically when the turn signal is in operation and turn on again when the turn signal is not operating. Lights-On Reminder If the headlights or parking lights are on after the ignition is turned to the LOCK position, a chime will sound to alert the driver when the driver’s door is opened.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Turn Signals Move the multifunction lever upward or downward and the corresponding turn signal indicator on the instrument panel will flash to show proper operation of the front and rear turn signal lights. Turn Signal Control Check for a defective outside light bulb if either light remains on and does not flash or has a very fast flash rate. If an indicator fails to light when the lever is moved, it would suggest that the fuse or indicator is defective.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE High Beam/Low Beam Select Switch Push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction lever toward you, to switch the headlights back to low beam. Flash-To-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will cause the headlights to turn on at high beam and remain on until the lever is released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 A courtesy light is also found in the rear of the center console. You can turn this light on and off from the dimmer control in the multifunction lever. This light is also controlled automatically by the Illuminated Entry System. Battery Saver Feature To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dimmer Control The dimmer control is part of the multifunction lever. It controls the operation of the interior lights and the brightness of the instrument panel lights. Instrument Panel Dimming With the parking lights or headlights on, rotate the dimmer control upward or downward to change the brightness of the instrument panel lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column. Rotate the end of the lever to the first detent past the intermittent settings for Low-speed wiper operation, or to the second detent past the intermittent settings for high-speed wiper operation. NOTE: The wipers will automatically return to the “Park” position if you turn the ignition switch OFF while they are operating.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) • Always remove any buildup of snow that prevents the windshield wiper blades from returning to the off position. If the windshield wiper control is turned off and the blades cannot return to the off position, damage to the wiper motor may occur. Intermittent Wiper System Use the intermittent wiper system when weather conditions make a single wiping cycle with a variable pause between cycles desirable.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Mist Feature Push downward on the windshield wiper/washer control lever to activate a single wipe cycle to clear the windshield of road mist or spray from a passing vehicle. The wipers will continue to operate until you release the lever.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you activate the washer while the wiper control is in the delay range, the wipers will operate in low speed for two wipe cycles after releasing the lever and then resume the intermittent interval previously selected. If you activate the washer while the wiper control is in the off position, the wipers will operate for two wipe cycles and then turn off. TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 WARNING! The Electronic Speed Control lever is located on the right side of the steering wheel. Do not adjust the steering wheel while driving. The tilt/telescoping adjustment must be locked while driving. Adjusting the steering wheel while driving or driving without the tilt/telescoping adjustment locked could cause the driver to lose control of the vehicle.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate Push and release the ON/OFF button located on the end of the Electronic Speed Control lever. The CRUISE indicator in the instrument cluster will illuminate. To turn the system off, push and release the ON/OFF button a second time. The CRUISE indicator will turn off. Be sure to turn the system off when not in use. NOTE: The Electronic Speed Control system will automatically turn off when the ignition is turned OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 To Resume Speed If you deactivated the Electronic Speed Control without erasing the set speed from memory and your vehicle speed is above 20 mph (32 km/h) you can resume the previous set speed. To do so, push the lever up and release RESUME ACCEL, and then remove your foot from the accelerator pedal. To Vary The Speed Setting When the Electronic Speed Control is set, you can increase speed by pushing up and holding the lever RESUME ACCEL.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. The HomeLink威 buttons that are located in the headliner or sun visor designate the three different HomeLink威 channels. Using Electronic Speed Control On Hills NOTE: The Electronic Speed Control system maintains speed up and down hills. A slight speed change on moderate hills is normal.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 WARNING! • Your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Begin Programming 1. Turn the ignition switch to the ON/RUN position. 2. Hold the battery side of the handheld transmitter away from the HomeLink威 button you wish to program. Place the handheld transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink威 button you wish to program while keeping the indicator light in view. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 If the indicator light blinks rapidly for two seconds and then turns to a constant light, proceed to Step 5 “Programming A Rolling Code System.” 5. Programming A Rolling Code System At the garage door opener motor (in the garage), locate the “Learn” or “Training” button. 3 This can usually be found where the hanging antenna wire is attached to the garage door opener motor. It is NOT the button normally used to open and close the door.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7. Return to the vehicle and press the programmed HomeLink威 button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for two seconds) to complete the training. trained device (i.e.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. If you are having difficulties programming a garage door opener or a gate operator, replace “Programming HomeLink威” Step 3, with the following: 3.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Press the “Learn” button on the Garage Door Opener to complete the training for a Rolling Code. • Did you unplug the device for training, and remember to plug it back in? If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 NOTE: If desired, the instrument panel power outlet can be converted by your authorized dealer to provide power with the ignition switch while in the LOCK position. The center console power outlet is powered directly from the battery (power available at all times). Items plugged into this outlet may discharge the battery and/or prevent engine starting.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! To avoid serious injury or death: • Do not use a three-prong adapter. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 CIGAR LIGHTER AND ASH RECEIVER — IF EQUIPPED An optional ash receiver is available from your authorized dealer and will fit in the center console front cupholder. CAUTION! For vehicles equipped with the heated and cooled cupholder, locate the cup holder ash receiver in the forward cupholder. The optional ash receiver also comes with a cigar lighter.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated or Cooled Cupholder — If Equipped With this feature, the rear cavity of the cupholder can keep cool beverages cool, and hot beverages hot. The rear cupholder heats to 140°F (60°C) or cools to 35°F (1.6°C). The switch is located on the front of the center console and has three positions: Heat, Off, Cool. When the unit is on and the LED is Red, the cupholder is being heated. When the LED is Blue, the cupholder is being cooled.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Rear Seat Cupholders Cupholders for the rear seat occupants are located in the armrests. Each cupholder is capable of holding up to a 20 oz. (.5 L) bottle or can.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES Storage The center console contains a cubby bin with flip-down cover located below the climate controls. This compartment also contains a 12-Volt electrical outlet. WARNING! Do not place ashes inside the cubby bin located on the center console. A fire leading to bodily injury could result.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Two separate storage compartments are also located underneath the armrest. 3 1 — Release button for top compartment 2 — Release button for bottom compartment 3 — Top Compartment 4 — Bottom Compartment. You can access this compartment directly, without first exposing the upper compartment, by operating the Release Button for the bottom compartment with the armrest down.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The top compartment holds small items, such as a pen and note pad, while the larger bottom compartment will hold CDs and alike. The bottom compartment also contains a 12-Volt power outlet and a molded-in coin holder (designed to hold various size coins). The console’s front opening lid allows for easy access to these compartments.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 REAR WINDOW FEATURES Rear Window Defroster — If Equipped The electric Rear Window Defroster switch is located on the climate control. Press this button to turn on the rear window defroster and the heated side mirrors (if equipped). An LED in the button will illuminate when the rear window defroster is on.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 178 ▫ Compass Display . . . . . . . . . . . . . . . . . . . . 198 䡵 Instrument Cluster – Base ▫ Personal Settings (Customer-Programmable Features) . . . . . . . . . . . . . . . . . . . . . . . . . . 200 . . . . . . . . . . . . . . . 179 䡵 Instrument Cluster – Premium . . . . . . . . . . . . 180 䡵 Instrument Cluster Descriptions . . . . . . . . . . .
176 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Notes On Playing MP3/WMA Files . . . . . . . 214 ▫ Operating Instructions — Radio Mode . . . . . 222 ▫ List Button (Disc Mode For MP3/WMA Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 ▫ Operation Instructions — CD Mode For CD And MP3 Audio Play . . . . . . . . . . . . . . . . . 225 ▫ Info Button (Disc Mode For MP3/WMA Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 ▫ Notes On Playing MP3 Files . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 177 䡵 Satellite Radio (RSC) — If Equipped (RER/REQ/REN Radios Only). . . . . . . . . . . . . 243 ▫ Right-Hand Switch Functions . . . . . . . . . . . . 248 ▫ System Activation . . . . . . . . . . . . . . . . . . . . 243 ▫ Left-Hand Switch Functions For Radio Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 249 ▫ Electronic Serial Number/Sirius Identification Number (ENS/SID) . . . . . . . . . 244 ▫ Left-Hand Switch Functions For Media (i.e.
178 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 2 3 4 5 — Air Outlet — Side Window Demister Outlet — Instrument Cluster — Ignition Switch — Analog Clock 6 — Radio 7 — Passenger Airbag 8 — Glove Box 9 — Heated Seat Switch – If Equipped 10 — Electronic Stability Program Off Button – If Equipped 11 — Hazard Switch 12 — Storage Compartment 13 — Climate Control 14 — Trunk Release Switch 15 — Power Top Switch
UNDERSTANDING YOUR INSTRUMENT PANEL 179 INSTRUMENT CLUSTER – BASE 4
180 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER – PREMIUM
UNDERSTANDING YOUR INSTRUMENT PANEL 181 INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Fuel Door Reminder This is a reminder that the Fuel Filler Door is located on the left side of the vehicle. 3. Temperature Gauge The temperature gauge shows engine coolant temperature. Any reading below the red area of the gauge shows that the engine cooling system is operating properly.
182 UNDERSTANDING YOUR INSTRUMENT PANEL 5. Low Fuel Light When the fuel level drops to approximately 2.0 gallons (7.6 Liters), the fuel symbol will light and a single chime will sound. NOTE: This light will remain on until a minimum of approximately 3.0 gallons of fuel is added. 6. Charging System Light This light shows the status of the electrical charging system. The light should come on briefly when the ignition is first turned on and remain on briefly as a bulb check.
UNDERSTANDING YOUR INSTRUMENT PANEL 183 9. Seat Belt Reminder Light When the ignition switch is first turned ON, this light will come on for about six seconds. A chime will sound if you have not pulled the shoulder belt out of the retractor. This is a reminder to “buckle up”. If you do not buckle up, the light will remain on. 10. Oil Pressure Warning Light This light indicates low engine oil pressure.
184 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: You must apply the brakes before shifting from PARK. 14. Odometer/Trip Odometer The odometer shows the total distance the vehicle has been driven. U.S. federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven.
UNDERSTANDING YOUR INSTRUMENT PANEL 185 GASCAP If the vehicle diagnostic system detects a leak or change in the evaporative system, or the fuel filler cap is loose, improperly installed, or damaged, the words “GASCAP” will display in the odometer. If this occurs, tighten the fuel filler cap properly and press the odometer reset button to turn off the “GASCAP” message. (Refer to “Onboard Diagnostic System — OBDII” in Section 7 of this manual for more information).
186 UNDERSTANDING YOUR INSTRUMENT PANEL 4. For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to “Electronic Vehicle Information Center (EVIC)” in this section of the manual. To reset the trip odometer, first set the display to Trip Mode. Then push and hold the button (approximately 2 seconds) until the display resets to 0 miles. The odometer must be in Trip Mode to reset the trip odometer. 15.
UNDERSTANDING YOUR INSTRUMENT PANEL 187 17. Electronic Throttle Control (ETC) Indicator Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a problem is detected, the light will come on while the engine is running. If the light remains lit with the engine running your vehicle will usually be drivable and not need towing, however see your dealer for service as soon as possible.
188 UNDERSTANDING YOUR INSTRUMENT PANEL The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system. Failure of either half of the dual brake system is indicated by the Brake Warning Light which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected.
UNDERSTANDING YOUR INSTRUMENT PANEL 189 The light also will turn on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 20. Turn Signal Indicators The arrows will flash in unison with the exterior turn signal, when using the turn signal lever. 21. Front Fog Light Indicator — If Equipped This light indicates when the front fog lights are ON. 22.
190 UNDERSTANDING YOUR INSTRUMENT PANEL If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefit of Anti-Lock Brakes. The ABS warning light should be checked frequently to assure that it is operating properly. Turn the ignition key to the on position, but do not start the vehicle. The light should come on. If the light does not come on, have the system inspected by an authorized dealer. 24.
UNDERSTANDING YOUR INSTRUMENT PANEL 191 Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists.
192 UNDERSTANDING YOUR INSTRUMENT PANEL 25. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system called OBD that monitors emissions, engine, and automatic transaxle control systems. The light will illuminate when the key is in the ON position before engine start. If the bulb does not come on when turning the key from LOCK to ON, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc.
UNDERSTANDING YOUR INSTRUMENT PANEL 193 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) – IF EQUIPPED The Electronic Vehicle Information Center (EVIC) features a driver-interactive display that is located in the instrument cluster.
194 UNDERSTANDING YOUR INSTRUMENT PANEL The system allows the driver to select information by pressing the following buttons on the Instrument Panel Switch Bank: Press and release the MENU button to advance the display to Trip Functions or Personal Settings or to return to the default System Status MENU display. Press and release the COMPASS button to display the compass heading and the outside temperature. COMPASS Button Press and release the RESET Button to accept a selection.
UNDERSTANDING YOUR INSTRUMENT PANEL 195 Electronic Vehicle Information Center (EVIC) Displays When the appropriate conditions exist, the Electronic Vehicle Information Center (EVIC) displays the following messages.
196 UNDERSTANDING YOUR INSTRUMENT PANEL Oil Change Required Your vehicle is equipped with an engine oil change indicator system. The “Oil Change Required” message will flash in the EVIC display for approximately five seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style.
UNDERSTANDING YOUR INSTRUMENT PANEL 197 The Trip Functions mode displays the following information: • Average Fuel Economy Shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read, RESET or show dashes for two seconds. Then, the history information will be erased, and the averaging will continue from the last fuel average reading before the reset.
198 UNDERSTANDING YOUR INSTRUMENT PANEL To reset all resettable functions, press and release the RESET button a second time within three seconds of resetting the currently displayed function (Reset ALL will display during this three-second window). Compass Display The compass heading indicates the direction the vehicle is facing. Press and release the compass button to display one of eight comCOM- pass heading and the outside temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL 199 5. Drive the vehicle slowly, completing one or more circles (in an area free from large metal or metallic objects) until the CAL indicator turns off. The compass will now function normally. Compass Variance Compass Variance is the difference between magnetic North and Geographic North. In some areas of the country, the difference between magnetic and geographic North is great enough to cause the compass to give false readings.
200 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Press and release the STEP button until “Compass Variance” and the current Variance Value displays in the EVIC. 4. Press and release the RESET button to increment the Variance Value by one, (one button press per update), until the proper variance zone is selected according to the map. NOTE: The Variance Values will wrap around from 15 back to 1. The Default Variance is Zone 8. 5. Press and release the STEP button to exit.
UNDERSTANDING YOUR INSTRUMENT PANEL 201 Remote Key Unlock When Driver Door 1st Press is selected, only the driver’s door will unlock on the first press of the Remote Keyless Entry transmitter UNLOCK button. When Driver Door 1st Press is selected, you must press of the RKE transmitter unlock button twice to unlock the passenger’s doors. When All Doors 1st Press is selected, all of the doors will unlock on the first press of the RKE transmitter UNLOCK button.
202 UNDERSTANDING YOUR INSTRUMENT PANEL off if they were turned on by this feature. To make your selection, press and hold the RESET button until ON or OFF appears. unlocked with the RKE transmitter. To make your selection, press and hold the RESET button until OFF, 30 sec, 60 sec, or 90 sec appears. NOTE: Turning the headlights on during the daytime causes the instrument panel lights to dim. To increase the brightness, refer to “Lights” in Section 3 of this manual.
UNDERSTANDING YOUR INSTRUMENT PANEL 203 SALES CODE REQ — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Press the ON/VOLUME control knob a second time to turn off the radio.
204 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it.
UNDERSTANDING YOUR INSTRUMENT PANEL 205 Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the right side TUNE/ SCROLL control knob. 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save the time change. 5. To exit, press any button/knob or wait five seconds.
206 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a second time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the mid-range tones. Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 207 Toggle the MUSIC TYPE button to select the following format types: Program Type No program type or undefined Adult Hits Classical Classic Rock College Country Foreign Language Information Jazz News Nostalgia Oldies 16-Digit Character Display None Adlt Hit Classicl Cls Rock College Country Language Inform Jazz News Nostalga Oldies Program Type Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top
208 UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode. If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be exited and the radio will tune to the preset station.
UNDERSTANDING YOUR INSTRUMENT PANEL 209 • Angle – Repeatedly pressing SELECT will change the viewing angle if supported by the DVD disc (if equipped). NOTE: • The available selections for each of the above entries varies depending upon the disc. • These selections can only be made while playing a DVD. • VES™ Power - Allows you to turn VES™ ON and OFF (if equipped). • VES™ Lock - Locks out rear VES™ remote controls (if equipped).
210 UNDERSTANDING YOUR INSTRUMENT PANEL Audio Language — If Equipped Selecting this item allows you to choose a default audio language (effective only if the language is supported by the disc). You can select a language not listed by scrolling down and selecting ⬙other.⬙ Enter the country code using the TUNE/SCROLL control knob to scroll up and down to select the number and then push to select.
UNDERSTANDING YOUR INSTRUMENT PANEL 211 a disc is loaded, changes will not be effective. Also, the defaults are effective only if the disc supports the customer-preferred settings. AM and FM Buttons Press the buttons to select AM or FM Modes. SET Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window.
212 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (DISC MODE for CD and MP3/WMA Audio Play, DVD-VIDEO) The radio DVD player and many DVD discs are coded by geographic region. These region codes must match in order for the disc to play. If the region code for the DVD disc does not match the region code for the radio DVD player, it will not play the disc. Customers may take their vehicle to an authorized dealer to change the region code of the player a maximum of five times.
UNDERSTANDING YOUR INSTRUMENT PANEL 213 Eject Button — Ejecting Compact Disc(s) Press the EJECT button and the pushbutton with the corresponding number (1-6) where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc. Press and hold the EJECT button for five seconds and all CDs will be ejected from the radio. The disc can be ejected with the radio and ignition OFF.
214 UNDERSTANDING YOUR INSTRUMENT PANEL Notes On Playing MP3/WMA Files The radio can play MP3/WMA files; however, acceptable MP3/WMA file recording media and formats are limited. When writing MP3/WMA files, pay attention to the following restrictions.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 If a disc contains multi-formats, such as CD audio and MP3/WMA tracks, the radio will only play the MP3/ WMA tracks on that disc. MPEG Specification Supported MP3/WMA File Formats The radio will recognize only files with the *.MP3/WMA extension as MP3/WMA files. Non-MP3/WMA files named with the *.MP3/WMA extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3/WMA and will not play the file.
216 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3/WMA Files When a medium containing MP3/WMA data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3/WMA files.
UNDERSTANDING YOUR INSTRUMENT PANEL 217 Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display. SCAN Button (Auxiliary Mode) No function. Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3/WMA player, cassette player, or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
218 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Voice Recognition System (VR) (If Equipped) For the radio, refer to “Voice Recognition System (VR)” in Section 3. Dolby威 Manufactured under license from Dolby威 Laboratories. ⬙Dolby威⬙ and the double-D symbol are trademarks of Dolby威 Laboratories. For UConnect威 “Voice Recognition System (VR),” refer to “Hands-Free Communication (UConnect威)” in Section 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 AM/FM/CD/DVD MULTIMEDIA SYSTEM RADIO (RER/REN) – IF EQUIPPED NOTE: The sales code is located on the lower right side of the unit’s faceplate. The REN and RER Multimedia systems contain a radio, CD/DVD player, USB port, and a 30-gigabyte hard drive (HDD). Sirius Satellite Radio is optional. The 6.5 in (16.5 cm) touch screen allows for easy menu selection. The RER radio also contains a Global Positioning System (GPS)-based Navigation system.
220 UNDERSTANDING YOUR INSTRUMENT PANEL To Manually Set the Clock — RER/REN 1. Turn on the multimedia system. 2. Touch the screen where the time is displayed. 3. Touch the screen where “User Clock” is displayed. The clock setting menu will appear on the screen. 4. To move the hour forward, touch the screen where the word “Hour” with the arrow pointing upward is displayed. To move the hour backward, touch the screen where the word “Hour” with the arrow pointing downward is displayed. 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 Show Time if Radio is Off When selected, this feature will display the time of day on the touch screen when the multimedia system is turned off. Proceed as follows to change the current setting: Changing the Time Zone 1. Turn on the multimedia system. 3. Touch the screen where the words “Set Time Zone” are displayed. The time zone selection menu will appear on the screen. 2. Touch the screen where the time is displayed.
222 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RES — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the On/Volume control knob to turn on the radio. Push the On/Volume control knob a second time to turn off the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 223 SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it. TIME Button Press the TIME button and the time of day will display.
224 UNDERSTANDING YOUR INSTRUMENT PANEL Setting the Tone, Balance, and Fade Push the rotary Tune/Scroll control knob and BASS will display. Turn the Tune/Scroll control knob to the right or left to increase or decrease the bass tones. Push the rotary Tune/Scroll control knob a fifth time and FADE will display. Turn the Tune/Scroll control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary Tune/Scroll control knob a second time and MID will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET/RND button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice.
226 UNDERSTANDING YOUR INSTRUMENT PANEL If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. CAUTION! • This CD player will accept 4-3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD, MP3 modes. TIME Button Press this button to change the display from a large CD playing time display to a small CD playing time display. RW/FF Press the RW button to stop the CD at the beginning of the current CD track/title.
228 UNDERSTANDING YOUR INSTRUMENT PANEL Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file normally. UDF and Apple HFS formats are not supported.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported.
230 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL 231 SALES CODE RES/RSC — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) AND SIRIUS RADIO NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the On/Volume control knob to turn on the radio. Push the On/Volume control knob a second time to turn off the radio.
232 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. Voice Recognition System (Radio) — If Equipped Refer to “Voice Recognition System (VR)” in Section 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 233 3. After adjusting the hours, press the right side Tune/ Scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side Tune/Scroll control knob. Press the Tune/Scroll control knob to save time change. 5. To exit, press any button/knob or wait five seconds. The clock can also be set by pressing the SETUP button.
234 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary Tune/Scroll control knob a second time and MID will display. Turn the Tune/Scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary Tune/Scroll control knob a third time and TREBLE will display. Turn the Tune/Scroll control knob to the right or left to increase or decrease the treble tones. Push the rotary Tune/Scroll control knob a fourth time and BALANCE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 235 Program Type Foreign Language Information Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues 16-Digit Character Display Language Inform Jazz News Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R&B Program Type Sports Talk Top 40 Weather 16-Digit Character Display Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is disp
236 UNDERSTANDING YOUR INSTRUMENT PANEL SETUP Button Pressing the SETUP button allows you to select between the following items: • Set Clock — Pressing the SELECT button will allow you to set the clock. Turn the Tune/Scroll control knob to adjust the hours and then press and turn the Tune/Scroll control knob to adjust the minutes. Press the Tune/Scroll control knob again to save changes. AM/FM Button Press the button to select either AM or FM mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 DISC/AUX Button Pressing the DISC/AUX button will allow you to switch from AM/FM modes to DISC/AUX mode. radio display. If a CD does not go into the slot more than 1.0 in (2.5 cm), a disc may already be loaded and must be ejected before a new disc can be loaded. Operation Instructions — CD MODE for CD and MP3 Audio Play If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc.
238 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! (Continued) • RES is a single CD player. Do not attempt to insert a second CD if one is already loaded. • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player. EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 AM/FM Button Press the button to select either AM or FM mode. SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the right SEEK button to move to the next randomly selected track. Press the SET/RND button a second time to stop Random Play.
240 UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of folders. (The radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name and will assign a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.
UNDERSTANDING YOUR INSTRUMENT PANEL 241 MPEG Specification MPEG-1 Audio Layer 3 MPEG-2 Audio Layer 3 Sampling Bit Rate (kbps) Frequency (kHz) 320, 256, 224, 192, 160, 128, 48, 44.1, 32 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 24, 22.05, 16 56, 48, 40, 32, 24, 16, 8 ID3 Tag information for artist, song title, and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported.
242 UNDERSTANDING YOUR INSTRUMENT PANEL To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs. To create a single-session disc, enable the “Disc at Once” option before writing to the disc. LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the Tune/Scroll control knob.
UNDERSTANDING YOUR INSTRUMENT PANEL 243 NOTE: The AUX device must be turned on and the device’s volume set to proper level. If the AUX audio is not loud enough, turn the device’s volume up. If the AUX audio sounds distorted, turn the device’s volume down. TIME Button (Auxiliary Mode) Press this button to change the display to time of day. The time of day will display for five seconds (when ignition is OFF).
244 UNDERSTANDING YOUR INSTRUMENT PANEL 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID). 2. Your Vehicle Identification Number. Electronic Serial Number/Sirius Identification Number (ENS/SID) The Electronic Serial Number/Sirius Identification Number is needed to activate your Sirius Satellite Radio system.
UNDERSTANDING YOUR INSTRUMENT PANEL 245 Reception Quality Satellite reception may be interrupted due to one of the following reasons: • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception in the form of short audio mutes. • Driving under wide bridges or along tall buildings can cause intermittent reception. • Placing objects over or too close to the antenna can cause signal blockage.
246 UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button Pressing the INFO button will cycle between Artist, Song Title, and Composer (if available) information. Also, pressing and holding the INFO button for an additional 3 seconds will make the radio display the Song Title all of the time (press and hold again to return to normal display). RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next channel in the direction of the arrows.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 SET Button — To Set the Push-Button Memory When you are receiving a channel that you wish to commit to push-button memory, press the SET button. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and press and release that button. If a button is not selected within 5 seconds after pressing the SET button, the channel will continue to play but will not be stored into push-button memory.
248 UNDERSTANDING YOUR INSTRUMENT PANEL REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. The left and right controls are rocker-type switches with a pushbutton in the center of each switch. Reach behind the steering wheel to access the switches. Remote Sound System Controls Right-Hand Switch Functions • Press the top of the switch to increase the volume. • Press the bottom of the switch to decrease the volume.
UNDERSTANDING YOUR INSTRUMENT PANEL 249 Left-Hand Switch Functions for Radio Operation • Press the top of the switch to SEEK the next listenable station up from the current setting. • Press the bottom of the switch to SEEK the next listenable station down from the current setting. • Press the button in the center of the switch to tune to the next preset that you have programmed. Left-Hand Switch Functions for Media (i.e.
250 UNDERSTANDING YOUR INSTRUMENT PANEL 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. NOTE: If you experience difficulty in playing a particular disc, it may be damaged (i.e. scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have theft protection encoding. Try a known good disc before considering disc player service.
UNDERSTANDING YOUR INSTRUMENT PANEL 251 Blower Control Rotate this control to regulate the amount of air forced through the ventilation system in any mode. The blower speed increases as you move the control to the right from the “O” (OFF) position. There are four blower speeds. NOTE: For vehicles equipped with Remote Start, the climate controls will not function during Remote Start operation if the blower control is left in the “O” (Off) position.
252 UNDERSTANDING YOUR INSTRUMENT PANEL Mode Control (Air Direction) Rotate this control to choose from several patterns of air distribution. You can select either a primary mode as identified by the symbols on the control, or a blend of two of these modes. The closer the setting is to a particular symbol, the more air distribution you receive from that mode. Panel Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow.
UNDERSTANDING YOUR INSTRUMENT PANEL 253 Defrost Air is directed through the windshield and side window demist outlets. Use this mode with maximum blower and temperature settings for best windshield and side window defrosting. NOTE: The air conditioning compressor operates in Mix, Defrost, or a blend of these modes, even if the Air Conditioning (A/C) button is not pressed. This dehumidifies the air to help dry the windshield. To improve fuel economy, use these modes only when necessary.
254 UNDERSTANDING YOUR INSTRUMENT PANEL • When the ignition switch is turned to the LOCK position, the recirculation feature will be cancelled. Air Conditioning Control Press in on this button to engage the Air Conditioning. A light will illuminate when the Air Conditioning System is engaged. Rotating the dial left into the blue area of the scale indicates cooler temperatures while the rotating right into the red area indicates warmer temperatures.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 Automatic Operation The Infrared Climate Control System automatically maintains the climate in the cabin of the vehicle at the comfort levels desired by the driver and passenger. To accomplish this, the system gathers information from the cabin infrared sensor mounted between the sun-visors and from various sensors located throughout the vehicle. The controls on the climate control provide the system with operator input.
256 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • The temperature setting can be adjusted at anytime without affecting automatic operation. • Pressing the Air Conditioning Control button while in AUTO mode will cause the LED in the control button to flash three times and then turn off. This indicates that the system is in AUTO mode and requesting the air conditioning is not necessary.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 4
258 UNDERSTANDING YOUR INSTRUMENT PANEL The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Control knob (on the right) to one of the following positions. • Panel Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. NOTE: The center instrument panel outlets can be aimed so that they are directed toward the rear seat passengers for maximum airflow to the rear.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 • Air Conditioner Control Press this button to turn on the air conditioning during manual operation only. When the air conditioning is turned on, cool dehumidified air will flow through the outlets selected with the Mode control dial. Press this button a second time to turn OFF the air conditioning. An LED in the button illuminates when manual compressor operation is selected. • Recirculation Control The system will automatically control recirculation.
260 UNDERSTANDING YOUR INSTRUMENT PANEL • Most of the time, when in Automatic Operation, you can temporarily put the system into Recirculation Mode by pressing the Recirculation Button. However, under certain conditions, while in Automatic Mode, the system is blowing air out the defrost vents. When these conditions are present, and the Recirculation Button is pressed, the indicator will flash and then turn off. This tells you that you are unable to go into recirculation mode at this time.
UNDERSTANDING YOUR INSTRUMENT PANEL 261 Window Fogging Interior fogging on the windshield can be quickly removed by turning the mode selector to Defrost. The Defrost/Floor mode can be used to maintain a clear windshield and provide sufficient heating. If side window fogging becomes a problem, increase blower speed. Vehicle windows tend to fog on the inside in mild but rainy or humid weather. NOTE: Recirculate without A/C should not be used for long periods as fogging may occur.
262 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions for Various Weather Conditions
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 267 ▫ Brake/Transaxle Interlock System . . . . . . . . . 272 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 267 ▫ Automatic Transaxle Ignition Interlock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273 ▫ Tip Start Feature . . . . . . . . . . . . . . . . . . . . . 268 ▫ 4 Speed/6 Speed Automatic Transaxle . . . . . 273 ▫ Extremely Cold Weather (Below ⫺20°F Or ⫺29°C) . . . . . . .
264 STARTING AND OPERATING ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . 279 ▫ Brake Assist System (BAS) . . . . . . . . . . . . . . 293 䡵 Driving Through Water . . . . . . . . . . . . . . . . . 280 ▫ Electronic Stability Program (ESP) . . . . . . . . 294 ▫ Flowing/Rising Water . . . . . . . . . . . . . . . . . 280 䡵 Tire Safety Information . . . . . . . . . . . . . . . . . 297 ▫ Shallow Standing Water . . . . . . . . . . . . . . . 280 ▫ Tire Markings . . . . . . . . . . . . . .
STARTING AND OPERATING 265 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . 312 ▫ Reformulated Gasoline . . . . . . . . . . . . . . . . 327 ▫ Life Of Tire . . . . . . . . . . . . . . . . . . . . . . . . 313 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . . 327 ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . 313 ▫ E-85 Usage In Non-Flex Fuel Vehicles . . . . . . 328 䡵 Tire Chains . . . . . . . . . . . . . . . . . . . . . . . . . . 315 ▫ MMT In Gasoline . . . . . . . . . . . .
266 STARTING AND OPERATING ▫ Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . 333 䡵 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 339 ▫ Cruising Range . . . . . . . . . . . . . . . . . . . . . . 333 ▫ Common Towing Definitions . . . . . . . . . . . . 339 ▫ Replacement Parts . . . . . . . . . . . . . . . . . . . 333 ▫ Trailer Hitch Classification . . . . . . . . . . . . . . 341 ▫ Maintenance . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 267 STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. Make sure all occupants have securely fastened their seat belts. WARNING! • Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition.
268 STARTING AND OPERATING Tip Start Feature Do not press the accelerator. Turn the ignition key briefly to START position, and release it. The starter motor will continue to run, and it will disengage automatically when the engine is running. If the engine fails to start, the starter will disengage automatically in 10 seconds. If this occurs, turn the ignition switch to the LOCK position, wait 10 to 15 seconds, then repeat the normal starting procedure.
STARTING AND OPERATING 269 WARNING! (Continued) • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.
270 STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a grounded, three-wire extension cord. The engine block heater cord is routed under the hood on the passenger side of the vehicle near the right head lamp assembly. It is located between the front grille and the radiator, but underneath the black upper seal.
STARTING AND OPERATING 271 WARNING! WARNING! (Continued) • It is dangerous to move the shift lever out of or if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
272 STARTING AND OPERATING Brake/Transaxle Interlock System This system prevents you from moving the shift lever out of PARK and into any gear unless the brake pedal is pressed. This system is active only while the ignition switch is in the ON position. Always press the brake pedal first, before moving the shift lever out of PARK. NOTE: If a malfunction occurs, the transaxle will not shift out of PARK. Battery power is required to release the Brake/Transaxle Interlock system.
STARTING AND OPERATING 273 Automatic Transaxle Ignition Interlock System This system prevents the key from being removed unless the shift lever is in PARK. It also prevents shifting out of PARK unless the key is in the ON position, and the brake pedal is applied. NOTE: If a malfunction occurs, the system will trap the key in the ignition switch lock cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped, but the key cannot be removed until you obtain service.
274 STARTING AND OPERATING Gear Ranges PARK Supplements the parking brake by locking the transaxle. The engine can be started in this range. Never attempt to use PARK while vehicle is in motion. Apply parking brake when leaving vehicle in this range. When parking on a flat surface, place the shift lever into the PARK position first, and then apply the parking brake.
STARTING AND OPERATING 275 NEUTRAL Engine may be started in this range. WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have an accident. DRIVE – 6 Speed Transaxle This range should be used for most city and highway driving. It provides the smoothest upshifts, downshifts, and best fuel economy.
276 STARTING AND OPERATING DRIVE 3 — 4 Speed Transaxle This range eliminates shifts into fourth gear. The transaxle will operate normally in first and second gear. Shifts into third gear may be delayed to provide second gear operation at higher speeds.
STARTING AND OPERATING 277 In the event of a momentary problem, the transaxle can be reset to regain all forward gears by performing the following steps: 1. Stop the vehicle. 2. Shift the shift lever into PARK. 3. Turn the ignition switch to the LOCK position. 4. Restart the engine. 5. Shift the shift lever into the desired gear range and resume driving. NOTE: Even if the transaxle can be reset, it is recommended that you visit a dealer at your earliest possible convenience.
278 STARTING AND OPERATING NOTE: In Autostick威 mode, the transaxle will only shift up or down when the driver moves the shift lever to the Right (+) or Left (-). AutoStick威 is deactivated when the shift lever is moved from the AutoStick (+/-) position into the DRIVE position. General Information • You can start out in first or second gear. The system will ignore attempts to upshift at too low of a vehicle speed.
STARTING AND OPERATING 279 DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slippery surfaces may cause the front wheels to pull erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels. WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have an accident.
280 STARTING AND OPERATING DRIVING THROUGH WATER Driving through water more than a few inches/ centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle. Flowing/Rising Water WARNING! Do not drive on or cross a road or a path where water is flowing and/or rising (as in storm run-off). Flowing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Furthermore, flowing and/or rising water can carry your vehicle away swiftly.
STARTING AND OPERATING 281 CAUTION! (Continued) WARNING! • Driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.e., engine oil, transmission/transaxle, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water. Do not continue to operate the vehicle if any fluid appears contaminated, as this may result in further damage.
282 STARTING AND OPERATING POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these conditions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.
STARTING AND OPERATING 283 apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through an authorized dealer. No chemical flushes should be used in any power steering system; only the approved lubricant may be used. WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading. Do not overfill. Use only manufacturer’s recommended power steering fluid.
284 STARTING AND OPERATING As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. To apply the parking brake, grasp the handle and pull it upward until you feel resistance. To release the parking brake, grasp the handle and pull it slightly while pressing the button on the end of the handle. When the button drops into the handle (releasing the lock), guide the handle downward to its stop, and then release the button and the handle.
STARTING AND OPERATING 285 • If the parking brake is applied while the vehicle is moving, a chime will sound to alert the driver. The chime will sound up to 10 times or until the vehicle has returned to a stop. The Brake System Warning Light in the instrument cluster will turn on when the parking brake is applied and the ignition switch is on. NOTE: This light only shows that the parking brake is applied. It does not show the degree of brake application.
286 STARTING AND OPERATING WARNING! WARNING! (Continued) • Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
STARTING AND OPERATING 287 If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes. If the ABS light does not come on when the ignition switch is turned to the ON position, have the bulb repaired as soon as possible. If both the Brake Warning Light and the ABS Light remain on, the Anti-Lock brakes (ABS) and Electronic Brake Force Distribution (EBD) systems are not functioning. Immediate repair to the ABS system is required.
288 STARTING AND OPERATING WARNING! The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals.
STARTING AND OPERATING 289 WARNING! • Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency. • Driving a vehicle with the Brake System Warning Light on is dangerous. A significant decrease in braking performance or vehicle stability during braking may occur.
290 STARTING AND OPERATING You also may experience the following when the brake system goes into Anti-lock: • The ABS motor running (it may continue to run for a short time after the stop), • The clicking sound of solenoid valves, • Brake pedal pulsations, and • A slight drop or fall away of the brake pedal at the end of the stop. These are all normal characteristics of ABS.
STARTING AND OPERATING 291 WARNING! (Continued) • The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
292 STARTING AND OPERATING If both the Brake System Warning Light and the AntiLock Brake Light remain on, the ABS and Electronic Brake Force Distribution (EBD) systems are not functioning. Immediate repair to the ABS system is required. ELECTRONIC BRAKE CONTROL SYSTEM Your vehicle may be equipped with an optional advanced electronic brake control system that includes Anti-Lock Brake System (ABS), Traction Control System (TCS), Brake Assist System (BAS), and Electronic Stability Program (ESP).
STARTING AND OPERATING 293 Brake Assist System (BAS) The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sensing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce braking distances. The BAS complements the Anti-Lock Brake System (ABS). Applying the brakes very quickly results in the best BAS assistance.
294 STARTING AND OPERATING Electronic Stability Program (ESP) This system enhances directional control and stability of the vehicle under various driving conditions. ESP corrects for over/under steering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the over/under steer condition. Engine power may also be reduced to help the vehicle maintain the desired path.
STARTING AND OPERATING 295 WARNING! (Continued) • ESP cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents. • The capabilities of an ESP-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user’s safety or the safety of others. This mode should be used for almost all driving situations.
296 STARTING AND OPERATING WARNING! In the Partial ESP mode, the engine torque reduction and stability features are desensitized. Therefore, the enhanced vehicle stability offered by ESP is unavailable. NOTE: To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, it may be desirable to switch to the “Partial Off” mode by pressing the ESP switch.
STARTING AND OPERATING 297 NOTE: • The ESP Indicator Light and the ESP/BAS Warning Light come on momentarily each time the ignition switch is turned ON. TIRE SAFETY INFORMATION Tire Markings • Each time the ignition is turned ON, the ESP System will be ON even if it was turned off previously. • The ESP Control System will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESP becomes inactive following the maneuver that caused the ESP activation. 5 1 — U.S.
298 STARTING AND OPERATING NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H.
STARTING AND OPERATING 299 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.
300 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
STARTING AND OPERATING 301 Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
302 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires.
STARTING AND OPERATING 303 NOTE: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded. For further information on GAWRs, vehicle loading, and trailer towing, refer to “Vehicle Loading” in this section. To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the Tire and Loading Information placard.
304 STARTING AND OPERATING 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “XXX” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 = 750, and 1400 – 750 = 650 lbs [295 kg]). 5. Determine the combined weight of luggage and cargo being loaded on the vehicle.
STARTING AND OPERATING 305 5
306 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 307 WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement.
308 STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.” Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1 km) after a 3 hour period.
STARTING AND OPERATING 309 Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high-speed vehicle operation.
310 STARTING AND OPERATING Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and reinstalled at the first opportunity. WARNING! Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). Temporary-use spare tires have limited tread life.
STARTING AND OPERATING 311 Limited Use Spare — If Equipped The limited use spare tire is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tire warning label located on the limited use spare tire and wheel assembly. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not. Installation of this limited use spare tire affects vehicle handling.
312 STARTING AND OPERATING Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck. Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. Refer to “Freeing A Stuck Vehicle” in Section 6 of this manual for additional information.
STARTING AND OPERATING 313 These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes approximately 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced.
314 STARTING AND OPERATING Information” placard for the size designation of your tire. The service description and load identification will be found on the original equipment tire. Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle. We recommend that you contact your original equipment or an authorized tire dealer with any questions you may have on tire specifications or capability.
STARTING AND OPERATING 315 WARNING! (Continued) CAUTION! • Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. Damage to the vehicle may result if tire chains are used. CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. TIRE CHAINS Due to limited clearance, tire chains are not recommended.
316 STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates and tend to develop irregular wear patterns. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on all season type tires.
STARTING AND OPERATING 317 TIRE PRESSURE MONITOR SYSTEM (TPMS) • The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure. • The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12 F (7 C). This means that when the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on cold inflation tire pressure.
318 STARTING AND OPERATING once the system receives the updated tire pressures. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. − For example, your vehicle may have a recommended cold (parked for more than three hours) placard pressure of 30 psi (207 kPa).
STARTING AND OPERATING 319 NOTE: • The TPMS is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure. • Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
320 STARTING AND OPERATING Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. Should this occur, you should stop as soon as possible, check the inflation pressure of each tire on your vehicle, and inflate each tire to the vehicle’s recommended cold placard pressure value.
STARTING AND OPERATING 321 NOTE: 1. The compact spare tire (if so equipped) does not have a tire pressure monitoring sensor. Therefore, the TPMS will not monitor the pressure in the compact spare tire. 2. If you install the compact spare tire in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition key cycle, a chime will sound and the TPM Telltale Light will turn ON. 3.
322 STARTING AND OPERATING • Three Trigger Modules (mounted in three of the four wheel-wells) • Various Tire Pressure Monitoring System Messages, which display in the Electronic Vehicle Information Center (EVIC) • Tire Pressure Monitoring Telltale Light Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires.
STARTING AND OPERATING 323 Should this occur, you should stop as soon as possible, and inflate all tires with low pressure (those flashing in the EVIC graphic) to the vehicle’s recommended cold placard pressure value. Once the system receives the updated tire pressures, the system will automatically update, the graphic display in the EVIC will stop flashing, and the Tire Pressure Monitoring Telltale Light will turn off.
324 STARTING AND OPERATING 1. Jamming due to electronic devices or driving next to facilities emitting the same Radio Frequencies as the TPM sensors. Light will remain ON, a chime will sound, and the EVIC will still display a flashing pressure value in the graphic display. 2. Installing some form of aftermarket window tinting that affects radio wave signals. 3.
STARTING AND OPERATING 325 5. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically. In addition, the TPM Telltale Light will turn OFF and the graphic in the EVIC will display a new pressure value instead of dashes (- -), as long no tire pressure is below the low-pressure warning limit in any of the four active road tires.
326 STARTING AND OPERATING 3.5L Engine The 3.5L engine is designed to meet all emissions regulations and provide satisfactory fuel economy and performance when using high-quality unleaded gasoline having an octane range of 89. The manufacturer recommends the use of 89 octane for optimum performance. The use of premium gasoline is not recommended.
STARTING AND OPERATING 327 Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Reformulated gasolines contain oxygenates, and are specifically blended to reduce vehicle emissions and improve air quality. The manufacturer supports the use of reformulated gasolines. Properly blended reformulated gasolines will provide excellent performance and durability of engine and fuel system components.
328 STARTING AND OPERATING E-85 Usage In Non-Flex Fuel Vehicles Non-FFV vehicles are compatible with gasoline containing 10% ethanol (E10). Gasoline with higher ethanol content may void the vehicle’s warranty.
STARTING AND OPERATING 329 It is even more important to look for gasolines without MMT in Canada, because MMT can be used at levels higher than those allowed in the United States. • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance and damage the emission control system. MMT is prohibited in Federal and California reformulated gasolines. • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat.
330 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
STARTING AND OPERATING 331 Along with the special E-85 fuel filler cap, your vehicle may display a badge, which also indicates it can operate on E-85. 5 E-85 Fuel Cap CAUTION! Only vehicles with the special E-85 fuel filler cap can operate on E-85.
332 STARTING AND OPERATING ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank. Do not use E-85 as a cleaning agent and never use it near an open flame.
STARTING AND OPERATING 333 Selection of Engine Oil For Flexible Fuel Vehicles (E-85) and Gasoline Vehicles FFV vehicles operated on E85 require specially formulated engine oils. These special requirements are included in MOPAR威 engine oils, and in equivalent oils meeting Chrysler Specification MS-6395. The manufacturer only recommends engine oils that are API Certified and meet the requirements of Material Standard MS-6395.
334 STARTING AND OPERATING CAUTION! Replacing fuel system components with non-ethanol compatible components can damage your vehicle. The gas cap is behind the fuel filler door, on the left rear quarter panel of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. Maintenance CAUTION! Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect driveability.
STARTING AND OPERATING 335 After removing the gas cap, place the gas cap tether cable over a hook on the inside of the fuel door. This keeps the gas cap suspended away from and protects the vehicle’s surface. CAUTION! • Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap).
336 STARTING AND OPERATING WARNING! (Continued) • Never add fuel when the engine is running. This is in violation of most state and federal fire regulations and doing so will cause the malfunction indicator light to turn on. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. NOTE: • Tighten the gas cap until you hear a “clicking” sound.
STARTING AND OPERATING 337 VEHICLE LOADING Vehicle Certification Label Your vehicle has a certification label attached to the rear of the driver’s door.
338 STARTING AND OPERATING WARNING! Because the front wheels steer the vehicle, it is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident. Overloading The load carrying components (axle, springs, tires, wheels, etc.) of your vehicle will provide satisfactory service as long as you do not exceed the GVWR and front and rear GAWR.
STARTING AND OPERATING 339 TRAILER TOWING In this section, you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible. To maintain warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.
340 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR. WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident.
STARTING AND OPERATING 341 Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Refer to the Trailer Towing Weights (Maximum Trailer Weight Ratings) chart for the Max. GTW towable for your given drivetrain. Trailer Hitch Classification Max. GTW Class (Gross Trailer Wt.
342 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Maximum Trailer Weight Ratings Max. GTW (Gross Trailer Engine/Transaxle Max. Frontal Area Wt.) 2.4L/Auto See Note 2 1,000 lbs (450 kg) 2.7L/Auto See Note 2 1,500 lbs (680 kg) 3.5L/Auto 22 sq.ft. (2.0 sq.m) 2,000 lbs (900 kg) Refer to local laws for maximum trailer towing speeds.
STARTING AND OPERATING 343 CAUTION! Towing a trailer with a larger than recommended frontal area could cause the engine to overheat or cause severe engine damage under extreme conditions. Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
344 STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information placard in the Tire Safety Information section of this manual for the maximum combined weight of occupants and cargo for your vehicle.
STARTING AND OPERATING 345 WARNING! • Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: • Make certain that the load is secured in the trailer and that it will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have an accident.
346 STARTING AND OPERATING 4. Trailer tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve 10% of trailer tongue weight as a percentage of total trailer weight). Towing Requirements — Tires • Do not attempt to tow a trailer while using a compact spare tire. • Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 347 • Trailer brakes are recommended for trailers over 1,000 lbs (450 kg) and required for trailers in excess of 2,000 lbs (907 kg). CAUTION! If the trailer weighs more than 1,000 lbs (450 kg) loaded, it should have its own brakes with adequate braking capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. WARNING! • Do not connect trailer brakes to your vehicle’s hydraulic brake lines.
348 STARTING AND OPERATING Automatic Transaxle The DRIVE range can be selected when towing. However, if frequent shifting occurs while in this range, third gear for a four-speed automatic and the fifth gear for a six-speed AutoStick威 should be selected. NOTE: Check the four-speed automatic transaxle fluid level before towing. AutoStick威 six—speed transmission is sealed and the fluid level cannot be checked. See your authorized dealership service center for assistance.
STARTING AND OPERATING 349 Cooling System To reduce potential for engine and transaxle overheating, take the following actions: • City Driving When stopped for short periods of time, put transaxle in neutral and increase engine idle speed. • Highway Driving Reduce speed. • Air Conditioning Turn off temporarily. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle (Flat towing with all four wheels on the ground) CAUTION! DO NOT flat tow this vehicle.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . 352 ▫ Jacking Instructions . . . . . . . . . . . . . . . . . . . 356 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 352 䡵 Jump-Starting Procedure . . . . . . . . . . . . . . . . 361 ▫ Engine Oil Overheating — 2.4L Engine Only (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . 353 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 364 䡵 Jacking And Tire Changing . . . . . . . . . .
352 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The Hazard Warning flasher switch is located in the instrument panel switch bank above the climate controls. Press the switch to turn on the Hazard Warning flashers. When the Hazard Warning flasher switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the switch a second time to turn off flashers. This is an emergency warning system and it should not be used when the vehicle is in motion.
WHAT TO DO IN EMERGENCIES 353 the fan control to High. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the H (red) mark, the instrument cluster will sound a chime. Pull over and stop the vehicle with the engine at idle, when safe. Turn off the air conditioning and wait until the pointer drops back into the normal range.
354 WHAT TO DO IN EMERGENCIES NOTE: Engine speed is reduced to 53 mph (85 km/h) at the maximum. You may of course, reduce your speed further if needed. JACKING AND TIRE CHANGING WARNING! • Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed.
WHAT TO DO IN EMERGENCIES 355 6. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if changing the right front tire, block the left rear wheel. Spare Tire Removal Lift up the load floor cover and remove the hold down. NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked. Jack Location The jack and jack-handle are stowed under the load floor in the trunk.
356 WHAT TO DO IN EMERGENCIES Jacking Instructions WARNING! (Continued) WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set an automatic transmission in PARK; a manual transmission in REVERSE.
WHAT TO DO IN EMERGENCIES 357 Jack Warning Label 1. Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the lug wrench, and remove the wrench from the jack assembly. NOTE: The Jack Handle attaches to the side of the jack with two attachment points. When the jack is partially expanded, the tension between the two attachment points holds the jack handle in place. 6 Removing Jack Handle From Jack 2.
358 WHAT TO DO IN EMERGENCIES Jacking Locations
WHAT TO DO IN EMERGENCIES 359 CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in Step 3. head is properly engaged with the lift area closest to the wheel to be changed. Do not raise the vehicle until you are sure the jack is securely engaged. WARNING! 3. There is one front jacking location and one rear jacking location on each side of the vehicle. The front locations are outlined by two triangular cutouts, the rear ones by two rectangular cutouts.
360 WHAT TO DO IN EMERGENCIES 6. Remove the wheel nuts, and pull the wheel and wheel covers (if equipped) off the hub. Install the spare wheel and wheel nuts with the cone shaped end of the nuts toward the wheel. Lightly tighten the nuts. To avoid the risk of forcing the vehicle off the jack, do not tighten the nuts fully until the vehicle has been lowered. WARNING! To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. 8. Finish tightening the nuts.
WHAT TO DO IN EMERGENCIES 361 10. Place the deflated (flat) tire in the cargo area, have the tire repaired or replaced as soon as possible. 11. Check the spare tire pressure as soon as possible. Correct pressure as required. JUMP-STARTING PROCEDURE The battery is stored between the left front headlight assembly and the left front wheel splash shield. Access is through the splash shield. Jump-starting remote battery terminals are located under the hood.
362 WHAT TO DO IN EMERGENCIES 2. When boosting from a battery in another vehicle, park that vehicle within booster cable reach, but without allowing the vehicles to touch. Set the parking brake, place the automatic transaxle in PARK and turn ignition to LOCK for both vehicles. WARNING! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could result. 3. Turn off the heater, radio, and all unnecessary electrical loads. 4.
WHAT TO DO IN EMERGENCIES 363 7. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery. 8. When removing the jumper cables, reverse the sequence exactly. Be careful of the moving belts and fan. 9. Reinstall the protective cover over the remote jumpstart positive battery post. WARNING! Jump-Starting Location 6.
364 WHAT TO DO IN EMERGENCIES NOTE: Refer to “Maintenance Procedures” in Section 7 of this manual for information on accessing the battery for service or replacement. WARNING! Any procedure other than above could result in: • Personal injury caused by electrolyte squirting out the battery vent; • Personal injury or property damage due to battery explosion; • Damage to charging system of booster vehicle or of immobilized vehicle.
WHAT TO DO IN EMERGENCIES 365 WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause axle and tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck, and don’t let anyone near a spinning wheel, no matter what the speed.
366 WHAT TO DO IN EMERGENCIES CAUTION! (Continued) • Do not attempt to tow this vehicle from the front with sling type towing equipment. Damage to the front fascia will result. • Do not push or tow this vehicle with another vehicle as damage to the bumper fascia and transaxle may result. If you must use the accessories (wipers, defrosters, etc.) while being towed, the key must be in the ON position, not the ACC position. Make certain the transaxle remains in NEUTRAL.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 2.4L . . . . . . . . . . . . . 369 䡵 Maintenance Procedures . . . . . . . . . . . . . . . . . 376 䡵 Engine Compartment — 2.7L . . . . . . . . . . . . . 370 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 376 䡵 Engine Compartment — 3.5L . . . . . . . . . . . . . 371 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 379 䡵 Onboard Diagnostic System — OBD II . . . . . . 372 ▫ Engine Air Cleaner Filter . . . . . . . . . .
368 MAINTAINING YOUR VEHICLE ▫ Windshield Washers . . . . . . . . . . . . . . . . . . 385 䡵 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . 411 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . 386 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 412 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . 388 ▫ Headlight . . . . . . . . . . . . . . . . . . . . . . . . . . 412 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 369 ENGINE COMPARTMENT — 2.
370 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 2.
MAINTAINING YOUR VEHICLE 371 ENGINE COMPARTMENT — 3.
372 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transaxle control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as maintaining engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 373 Loose Fuel Filler Cap Message After fuel is added, the vehicle diagnostic system can determine if the fuel filler cap is possibly loose or improperly installed. A “GASCAP” message will be displayed in the instrument cluster. Tighten the gas cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tightened. Press the trip odometer “Reset” button to turn off the message.
374 MAINTAINING YOUR VEHICLE Your vehicle has a simple ignition key-actuated test, which you can use prior to going to the test station. To check if your vehicle’s OBD II system is ready, you must do the following: 1. Insert your ignition key into the ignition switch. 2. Turn the ignition to the ON position, but do not crank or start the engine. 3. If you crank or start the engine, you will have to start this test over. 4.
MAINTAINING YOUR VEHICLE 375 Regardless of whether your vehicle’s OBD II system is ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL is on with the engine running. REPLACEMENT PARTS Use of genuine MOPAR威 parts for normal/scheduled maintenance and repairs is highly recommended to ensure the designed performance.
376 MAINTAINING YOUR VEHICLE MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance. However, if a malfunction of these items does occur, it could adversely affect the engine or vehicle performance.
MAINTAINING YOUR VEHICLE 377 CAUTION! Do not overfill the engine. Overfilling the engine will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Change Engine Oil The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to “Maintenance Schedule” in Section 8 of this manual for information on this system.
378 MAINTAINING YOUR VEHICLE Engine Oil Viscosity (SAE Grade) — 2.4L and 2.7L Engines SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. Your engine oil filler cap also shows the recommended engine oil viscosity for your vehicle. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to “Engine Compartment” in this section.
MAINTAINING YOUR VEHICLE 379 Materials Added to Engine Oils The manufacturer strongly recommends against the addition of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental additives. Disposing of Used Engine Oil and Oil Filters Care should be taken in disposing of used engine oil and oil filters from your vehicle.
380 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc.) removed.
MAINTAINING YOUR VEHICLE 381 WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery.
382 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you.
MAINTAINING YOUR VEHICLE 383 NOTE: Use only manufacturer approved A/C System Sealers, Stop Leak Products, Seal Conditioners, Compressor Oil, and Refrigerants. A/C Air Filter — If Equipped Refer to the “Maintenance Schedule” in Section 8 of this manual for the proper maintenance intervals. WARNING! Do not remove the A/C Air Filter while the blower is operating or personal injury may result. 2. Push in on the sides of the glove box and lower the door. 3.
384 MAINTAINING YOUR VEHICLE 5. Disengage the two retaining tabs that secure the filter cover to the HVAC housing and remove the cover. CAUTION! The A/C Air Filter is labeled with an arrow to indicate airflow direction through the filter. Failure to install the filter properly will result in the need to replace it more often. 8. Reinstall the glove box door dampener and glove box. A/C Air Filter Replacement 6. Remove the A/C Air Filter by pulling it straight out of the housing. 7.
MAINTAINING YOUR VEHICLE 385 attention should also be given to hood latching components to insure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. Avoid using the wiper blades to remove frost or ice from the windshield. Make sure that they are not frozen to the glass before turning them on to avoid damaging the blade.
386 MAINTAINING YOUR VEHICLE WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
MAINTAINING YOUR VEHICLE 387 Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. CAUTION! A hot exhaust system can start a fire if you park over materials that can burn.
388 MAINTAINING YOUR VEHICLE To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transaxle is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. • Do not idle the engine with any ignition coil connectors disconnected for prolonged periods. Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the LOCK position.
MAINTAINING YOUR VEHICLE 389 Check the coolant recovery bottle tubing for brittle rubber, cracking, tears, cuts, and tightness of the connection at the bottle and radiator. Inspect the entire system for leaks. Cooling System — Drain, Flush, and Refill If the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals.
390 MAINTAINING YOUR VEHICLE CAUTION! (Continued) • This vehicle has not been designed for use with Propylene Glycol based engine coolant (antifreeze). Use of Propylene Glycol based engine coolant (antifreeze) is not recommended. Adding Coolant Your vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals. This engine coolant (antifreeze) can be used up to 5 Years or 102,000 miles (170 000 km) before replacement.
MAINTAINING YOUR VEHICLE 391 NOTE: Mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze) and will require more frequent coolant changes. Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery bottle.
392 MAINTAINING YOUR VEHICLE Disposal of Used Engine Coolant Used ethylene glycol based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children, do not store ethylene glycol based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately.
MAINTAINING YOUR VEHICLE 393 Points To Remember NOTE: When the vehicle is stopped after a few miles (kilometers) of operation, you may observe vapor coming from the front of the engine compartment. This is normally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vaporized when the thermostat opens, allowing hot engine coolant (antifreeze) to enter the radiator.
394 MAINTAINING YOUR VEHICLE • Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory cooling performance, poor gas mileage, and increased emissions. Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “Maintenance Schedule” in Section 8 of this manual for the proper maintenance intervals.
MAINTAINING YOUR VEHICLE 395 Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter or moisture. WARNING! CAUTION! • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire.
396 MAINTAINING YOUR VEHICLE Fluid Level Check — Vehicles with 2.4L and 2.7L Engines Use the following procedure to check the automatic transaxle fluid level properly: 1. Park the vehicle on level ground. 2. Run the engine at curb idle speed for a minimum of 60 seconds. 3. Apply the parking brake fully. 4. Place the gear selector momentarily in each gear position ending with the lever in PARK. 5. Wipe the area around the dipstick clean to eliminate the possibility of dirt entering the transaxle. 6.
MAINTAINING YOUR VEHICLE 397 CAUTION! • Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than that recommended by the manufacturer will result in more frequent fluid and filter changes. Refer to “Fluids, Lubricants, and Genuine Parts” for the correct fluid type. • Dirt and water in the transaxle can cause serious damage.
398 MAINTAINING YOUR VEHICLE Appearance Care And Protection From Corrosion The most common causes are: Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.
MAINTAINING YOUR VEHICLE 399 • Use MOPAR威 Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.
400 MAINTAINING YOUR VEHICLE Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil and/or excessive brake dust, use MOPAR威 Wheel Cleaner or equivalent or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Only MOPAR威 or equivalent is recommended. Do not use oven cleaner.
MAINTAINING YOUR VEHICLE 401 MOPAR威 Spot & Stain Remover if absolutely necessary. Do not use harsh cleaners or Armorall. Use MOPAR威 Total Clean to clean vinyl upholstery Cleaning Leather Upholstery MOPAR威 Total Clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth.
402 MAINTAINING YOUR VEHICLE • For grease stains, apply MOPAR威 Multi-Purpose Cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • Do not use any solvents or protectants on Yes Essentials威 products. Glass Surfaces All glass surfaces should be cleaned on a regular basis with MOPAR威 Glass Cleaner or any commercial household-type glass cleaner. Never use an abrasive type cleaner.
MAINTAINING YOUR VEHICLE 403 Replace the belts if they appear frayed or worn or if the buckles do not work properly. Installation Align the liner in the cupholder and press down firmly. Dry with a soft tissue. Convertible Top Care Immediate removal of any contaminant is recommended. Regular washing of the top will enhance its life and appearance, and make successive cleanings easier. Do not subject the top to excessive heat. Frequently vacuum the top and storage compartment.
404 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! Avoid high-pressure car washes, as they can damage the top material. Also, increased water pressure may force water past the weather strips. Never use an abrasive type cleaner or bleaches. Cleaners should not contain silicones, organic solvents, petroleum distillates, or plasticizers. Always wait until the top is thoroughly dry before lowering it into the storage area.
MAINTAINING YOUR VEHICLE 405 Additional Cleaning Procedure For additional cleaning assistance in removing stubborn stains, apply MOPAR威 Convertible Cloth Top Cleaner to the complete stain, extending 2 inches (50 mm) beyond the stain. With a soft bristle brush, scrub in all directions over the stain. Avoid heavy scrubbing. Rinse the area with warm water. If the stain is still apparent, repeat the cleaning procedure. When the stain is no longer showing, rinse the complete top with warm water.
406 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Cavity 1 2 — Mini Fuse Description — Power Top Module (If Equipped) 20 Amp Yellow AWD Module 10 Amp Red 3 — 4 — 5 — 6 — 10 Amp Red 7 — 30 Amp Green Totally Integrated Power Module (TIPM) Cartridge Fuse 40 Amp Green Mini Fuse 10 Amp Red 20 Amp Yellow Description Battery Feed — Center High Mounted Stop Light (CHMSL)/ Brake Switch Battery Feed — Ignition Switch Trailer Tow — If Equipped Ignition Off Draw (IOD) — Power Mirror Switch/
MAINTAINING YOUR VEHICLE 407 Cavity 8 Cartridge Fuse — 9 40 Amp Green 10 — 11 — 12 — Mini Fuse Description Ignition Off 30 Amp Draw (IOD) Green Sense 2 Battery Feed — Power Seats - if equipped/PZEV Air Pump - if equipped Battery Feed — 20 Amp Cabin CompartYellow ment Node (CCN) 15 Amp Selectable Power Lt Blue Outlet 20 Amp — Yellow Cavity 13 Cartridge Fuse — 14 — 15 40 Amp Green 16 — Mini Fuse 20 Amp Yellow Description — Ignition Off Draw (IOD) — 10 Amp Cabin CompartRed ment Node (CC
408 MAINTAINING YOUR VEHICLE Cavity 17 Cartridge Fuse — Mini Fuse 10 Amp Red 18 40 Amp Green — 19 — 20 Amp Yellow — 15 Amp Lt. Blue 20 Description Ignition Off Draw (IOD) — Wireless Control Module (WCM)/ Clock/Steering Control Module (SCM) Battery Feed — Auto Shutdown (ASD) Relay Ignition Off Draw (IOD) — Power Amp Feed 2 - if equipped Ignition Off Draw (IOD) — Radio Cavity 21 Cartridge Fuse — Mini Fuse 10 Amp Red 22 — 10 Amp Red 23 — 15 Amp Lt.
MAINTAINING YOUR VEHICLE 409 Cavity 26 Cartridge Fuse — 27 — 28 — 29 — Mini Description Fuse 15 Amp Auto Shutdown Lt.
410 MAINTAINING YOUR VEHICLE Cavity 34 35 Cartridge Fuse 30 Amp Pink 40 Amp Green Mini Fuse — — Description Battery Feed — Anti-Lock Brakes (ABS) Module - if equipped/ Electronic Stability Program (ESP) Module - If Equipped Battery Feed — Anti-Lock Brakes (ABS) Module - If Equipped/ Electronic Stability Program (ESP) Module - If Equipped Cavity Cartridge Fuse 36 30 Amp Pink 37 — Mini Fuse Description Battery Feed — Passenger Door — Module (PDM)/ Driver Door Module (DDM) 25 Amp Power Top M
MAINTAINING YOUR VEHICLE 411 CAUTION! (Continued) • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it indicates a problem in the circuit that must be corrected. VEHICLE STORAGE If you will not be using your vehicle for more than 21 days, you may want to take steps to preserve your battery.
412 MAINTAINING YOUR VEHICLE LIGHT BULBS — Exterior Bulb No. Low Beam Headlight . . . . . . . . . . . . . . . . . . . . . 9006 High Beam Headlight. . . . . . . . . . . . . . . . . . . . . 9005 Front Park/Turn Signal/Side Marker Light . . . 3457AK Front Fog Light . . . . . . . . . . . . . . . . . . . . . 9145//H10 Center High Mounted Stop Light (CHMSL) . . . . . . . . . . . . . . . . . . . . . . . . W16W (921) Rear Tail/Stop Light . . . . . . . . . . . . . . . . . . . . . 3057 Rear Turn Signal Light . . . .
MAINTAINING YOUR VEHICLE 413 3. Rotate bulb and connector one-quarter turn and pull outward from assembly. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. 4. Pull the bulb out of the socket and replace the bulb. 5. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 6. Reinsert the bulb and socket assembly and rotate clockwise one-quarter turn to secure.
414 MAINTAINING YOUR VEHICLE Front Turn Signal/Parking Light 1. Raise and prop open the hood. 2. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the headlight housing. 3. Remove the bulb from the connector socket and install the replacement bulb. 4. Install the bulb and connector assembly into the headlight housing and rotate the connector one-quarter turn clockwise to lock it in place.
MAINTAINING YOUR VEHICLE 415 CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. 3. Install the bulb and connector assembly into the fog light housing and rotate the connector one-quarter turn clockwise to lock it in place. 2. Remove the bulb from the connector socket and install the replacement bulb.
416 MAINTAINING YOUR VEHICLE Tail/Stop, Rear Turn Signal and Backup Lights The taillights are a two piece design. The turn signal, brake and taillights are located in the rear corner body panel housing. The backup and taillights are located in the trunk lid housing. Changing the Tail/Stop Light or Rear Turn Signal Light 1. Open the trunk and gently pull back the trunk liner behind the tail lamp 2. Remove the two plastic wing nuts from the taillight housing.
MAINTAINING YOUR VEHICLE 417 1 — Tail/Stop Light 2 — Turn Signal Light 3. Grasp the taillight housing and pull it firmly outward while pushing gently on the studs from inside to disengage the housing from the vehicle. 5. Remove the bulb from the connector socket and install the replacement bulb. 4. Rotate the applicable bulb’s electrical connector onequarter turn counterclockwise and remove it from the taillight housing. 6.
418 MAINTAINING YOUR VEHICLE Changing the Backup Light 1. Open the trunk. 2. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the housing. 3. Remove the bulb from the connector socket and install the replacement bulb. 4. Install the bulb and connector assembly into the housing and rotate the connector one-quarter turn clockwise to lock it in place. License Plate Light 1. Remove two retaining screws holding the light lens in place.
MAINTAINING YOUR VEHICLE 419 2. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the CHMSL housing. 2. Gently pry the lens loose. 3. Pull bulb from socket, replace and reattach the light lens with the two retaining screws. Center High-Mounted Stop Light (CHMSL) 1. Open the trunk lid. 7 3. Remove the bulb from the connector socket and install the replacement bulb. 4.
420 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES U.S. Fuel (Approximate) 2.4L and 2.7L Engine 16.9 Gallons 3.5L Engine 17.2 Gallons Engine Oil with Filter 2.4L Engine (SAE 5W-20, API Certified) 4.5 Quarts 2.7L Engine (SAE 5W-20, API Certified) 5.5 Quarts 3.5L Engine (SAE 10W-30, API Certified) 5.5 Quarts Cooling System* 2.4L Engine (MOPAR威Antifreeze/Coolant 5 7.7 Quarts Year/100,000 Mile Formula) or equivalent. 2.7L Engine (MOPAR威 Antifreeze/Coolant 5 9.8 Quarts Year/100,000 Mile Formula) or equivalent.
MAINTAINING YOUR VEHICLE 421 FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Engine Coolant Organic Additive Technology) or equivalent Use API Certified engine oil. SAE 5W-20 is recommended. Refer to the enEngine Oil (2.4L and 2.7L Engine) gine oil fill cap for the correct SAE grade meeting Chrysler Material Standard MS-6395. Use API Certified engine oil. SAE 10W-30 is recommended.
422 MAINTAINING YOUR VEHICLE Component Fuel Selection (2.7L Engine - EXCEPT CALIFORNIA EMISSION STATES) Fuel Selection (3.5L Engine) Fluid, Lubricant, or Genuine Part E-85 Ethanol 89 Octane Chassis Component Automatic Transaxle Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4 Automatic Transmission Fluid MOPAR威 DOT 3 and SAE J1703 should be used. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance . . . . . . 424 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 424 ▫ Required Maintenance Intervals . . . . . . . . . .
M A I N T E N A N C E 424 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES 425 M NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicles oil if it has been 6 months since your last oil change even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, whichever comes first.
M A I N T E N A N C E S C H E D U L E S 8 426 MAINTENANCE SCHEDULES Once a Month At Each Oil Change • Check tire pressure and look for unusual wear or damage. • Change the engine oil filter. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of coolant reservoir, brake master cylinder, and transmission and add as needed. • Check all lights and other electrical items for correct operation. • Inspect the brake hoses and lines.
MAINTENANCE SCHEDULES 427 M 6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary.
M 428 MAINTENANCE SCHEDULES A I N 18,000 Miles (30,000 km) or T 18 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary.
MAINTENANCE SCHEDULES 429 M 30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule 36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule 42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs (2.4L Engine except PZEV*). ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
M 430 MAINTENANCE SCHEDULES A I N 48,000 Miles (80,000 km) or 48 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. C E ❏ Inspect the brake linings, and replace as necessary. S C H E D U L E S ❏ ❏ ❏ ❏ 54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
MAINTENANCE SCHEDULES 431 M 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the spark plugs (2.4L Engine except PZEV*). Inspect the brake linings, and replace as necessary. Replace the air conditioning filter (if equipped). Change the automatic transaxle fluid & filter if using your vehicle for any of the following: police, taxi, fleet, or frequent trailer towing.
M 432 MAINTENANCE SCHEDULES A I N 72,000 Miles (120,000 km) or 72 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. C E ❏ Inspect the brake linings, and replace as necessary. S C H E D U L E S ❏ ❏ ❏ ❏ 78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter.
MAINTENANCE SCHEDULES 433 M 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule 90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary. ❏ Replace the air conditioning filter (if equipped). ❏ Change the engine oil and engine oil filter.
M 434 MAINTENANCE SCHEDULES A I N 96,000 Miles (160,000 km) or 96 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. C E ❏ Inspect the brake linings, and replace as necessary. S C H E D U L E S ❏ ❏ ❏ ❏ Replace the air conditioning filter (if equipped). Inspect the CV joints. Inspect the exhaust system.
MAINTENANCE SCHEDULES 435 M 108,000 Miles (180,000 km) or 108 Months Maintenance Service Schedule 114,000 Miles (190,000 km) or 114 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary. ❏ Replace the air conditioning filter (if equipped). ❏ Change the engine oil and engine oil filter.
M 436 MAINTENANCE SCHEDULES A I N 120,000 Miles (200,000 km) or 120 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ Replace the engine air cleaner filter. C ❏ Replace the spark plugs (2.4L Engine except PZEV*). E ❏ Inspect the brake linings, and replace as necessary. S C H E D U L E S ❏ ❏ ❏ ❏ ❏ 126,000 Miles (210,000 km) or 126 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
MAINTENANCE SCHEDULES 437 M 132,000 Miles (220,000 km) or 132 Months Maintenance Service Schedule 138,000 Miles (230,000 km) or 138 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace as necessary. ❏ Replace the air conditioning filter (if equipped). ❏ Change the engine oil and engine oil filter.
M 438 MAINTENANCE SCHEDULES A I N 144,000 Miles (240,000 km) or 144 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. C E ❏ Inspect the brake linings, and replace as necessary. S C H E D U L E S ❏ ❏ ❏ ❏ Replace the air conditioning filter (if equipped). Inspect the CV joints. Inspect the exhaust system.
MAINTENANCE SCHEDULES 439 M † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 445 ▫ Prepare For The Appointment . . . . . . . . . . . 443 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 445 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 443 䡵 Warranty Information (U.S. Vehicles Only) . . . .
442 IF YOU NEED CONSUMER ASSISTANCE 䡵 Publication Order Forms . . . . . . . . . . . . . . . . 447 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 449 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 449 ▫ Temperature Grades . . . . . . . . . . . . . . . . . . 450 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 443 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
444 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealership. They want to know if you need assistance. • If an authorized dealership is unable to resolve the concern, you may contact the manufacturer’s customer center.
IF YOU NEED CONSUMER ASSISTANCE 445 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
446 IF YOU NEED CONSUMER ASSISTANCE WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. WARRANTY INFORMATION (U.S.
IF YOU NEED CONSUMER ASSISTANCE 447 To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov. PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below.
448 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-bystep troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.
IF YOU NEED CONSUMER ASSISTANCE 449 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle. All passenger car tires must conform to Federal safety requirements in addition to these grades.
450 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
452 INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . 283,288 ABS (Anti-Lock Brake System) . . . . . . . . . . . . 285,289 Accessory Delay, Power . . . . . . . . . . . . . . . . . . . . 13 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 390 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 334 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 385 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 453 Automatic Temperature Control (ATC) . . . . . . . . . 254 Automatic Transaxle . . . . . . . . . . . . . . . . . . . 270,395 Adding Fluid . . . . . . . . . . . . . . . . . . . 396,397,422 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397 Fluid and Filter Changes . . . . . . . . . . . . . . . . . 397 Fluid Level Check . . . . . . . . . . . . . . . . . . . 396,397 Interlock System . . . . . . . . . . . . . . . . . . . . 272,273 Reset Mode . . . . . . . . . . . . . . . . . . .
454 INDEX Calibration, Compass . . . . . . . . . . . . . . . . . . . . . 198 Capacities, Fluid . . . . . . . . . . . . . . . . . . . . . . . . 420 Caps, Filler Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334 Oil (Engine) . . . . . . . . . . . . . . . . . . 369,370,371,378 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 282 Radiator (Coolant Pressure) . . . . . . . . . . . . . . . 391 Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 455 Convertible . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Convertible Top . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Coolant Pressure Cap (Radiator Cap) . . . . . . . . . . 391 Cooler, Beverage Holder (Cupholder) . . . . . . . . . 168 Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . 388 Adding Coolant (Antifreeze) . . . . . . . . . . . . . . 390 Coolant Capacity . . . . . . . . . . . . . . . . . . . . . . 420 Coolant Level . . . . . . . . . . . . . . . .
456 INDEX Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . . . 376 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 282 Disabled Vehicle Towing . . . . . . . . . . . . . . . . . . . 365 Disposal Antifreeze (Engine Coolant) . . . . . . . . . . . . . . . 392 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 379 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Door Locks, Automatic . . . . . . . . . . . . . . . . . . . . 31 Door Opener, Garage .
INDEX 457 Exhaust Gas Caution . . . . . . . . . . . . . . . . . . 74,330 Fuel Requirements . . . . . . . . . . . . . . . . . . 325,420 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 361 Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 376,420,421 Oil Change Interval . . . . . . . . . . . . 185,196,377,424 Oil Filler Cap . . . . . . . . . . . . . . . . . 369,370,371,378 Oil Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379 Oil Filter Disposal . . . . . . . . . . .
458 INDEX Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 333 Fuel Requirements . . . . . . . . . . . . . . . . . . 330,332 Maintenance . . . . . . . . . . . . . . . . . . . . . . . 330,334 Replacement Parts . . . . . . . . . . . . . . . . . . . . . 333 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333 Flooded Engine Starting . . . . . . . . . . . . . . . . . . . 268 Floor Console . . . . . . . . . . . . . . . . . . . . . . . . . . 170 Fluid Capacities . . . . . . . .
INDEX 459 Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405 GVWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337 Garage Door Opener (HomeLink威) . . . . . . . . . . . 158 Gas Cap (Fuel Filler Cap) . . . . . . . . . . . . 334,336,373 Gasoline, Clean Air . . . . . . . . . . . . . . . . . . . . . . 327 Gasoline (Fuel) . . . . . . . . . . . . . . . . . . . . . . . . . 325 Gasoline, Reformulated . . . . . . . . . . . . . . . . . . . 327 Gauges Coolant Temperature . . .
460 INDEX Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 143,144 Time Delay . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Heated Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . 101 Heated Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250 Heater, Beverage Holder (Cupholder) . . . . . . . . . 168 Heater, Engine Block . . . . . . . . . . . . . . . . . . . . .
INDEX 461 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . . 361 Key, Programming . . . . . Key, Replacement . . . . . Key, Sentry (Immobilizer) Key-In Reminder . . . . . . Keyless Entry System . . . Keys . . . . . . . . . . . . . . Knee Bolster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
462 INDEX Headlight Switch . . . . . . . . . . . . . . . . . . . 143,144 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 Headlights On Reminder . . . . . . . . . . . . . . . . . 146 Headlights On With Wipers . . . . . . . . . . . . 144,153 High Beam . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 High Beam Indicator . . . . . . . . . . . . . . . . . . . . 192 High Beam/Low Beam Select . . . . . . . . . . . . . 148 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . .
INDEX 463 Low Tire Pressure System . . . . . . . . . . . . . . . . . Lower Anchors and Tether for CHildren (LATCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . . 317 66,68 . 384 . 139 Maintenance Free Battery . . . . . . . . . . . . . . . . . . 380 Maintenance, General . . . . . . . . . . . . . . . . . . . . . 376 Maintenance Procedures . . . . . . . . . . . . . . . . . .
464 INDEX Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . 376,421 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420 Change Interval . . . . . . . . . . . . . . . 185,196,377,424 Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376 Dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379,421 Filter Disposal . .
INDEX 465 Deck Lid Release . . . . . . . . . . . . . . . . . . . . . . . 36 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Outlet (Auxiliary Electrical Outlet) . . . . . . . . . . 164 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
466 INDEX Replacement Keys . . . . . . . . . . . . . . . . . . . . . . . . 16 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . 375 Replacement Tires . . . . . . . . . . . . . . . . . . . . . . . 313 Reporting Safety Defects . . . . . . . . . . . . . . . . . . . 446 Resetting Oil Change Indicator . . . . . . . . . . . 185,196 Restraint, Head . . . . . . . . . . . . . . . . . . . . . . . 55,141 Restraints, Child . . . . . . . . . . . . . . . . . . . . . . . . . 62 Restraints, Occupant . . . .
INDEX 467 Height Adjustment . . . . . . . . . . . . . . . . . . . . . 135 Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . 139 Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 Reclining . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 Seatback Release . . . . . . . . . . . . . . . . . . . . . . . 140 Tilting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
468 INDEX Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282 Tilt Column . . . . . . . . . . . . . . . . . . . . . . . . . . 154 Wheel, Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 Steering Wheel Mounted Sound System Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170,411 Storage, Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 260 Stuck, Freeing . . . . . . . . . . . . .
INDEX 469 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 313 Load Capacity . . . . . . . . . . . . . . . . . . . . . . . . 302 Pressure Monitor System (TPMS) . . . . . . . . . . . 317 Pressure Warning Light . . . . . . . . . . . . . . . . . . 190 Quality Grading . . . . . . . . . . . . . . . . . . . . . . . 449 Radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 313 Rotation . . . . . . . . . . . . . . . . .
470 INDEX Overdrive . . . . . . . . . . . . . . . . . . . . . . . . . . . 275 Selection of Lubricant . . . . . . . . . . . . . . . . . . . 422 Transmission . . . . . . . . . . . . . . . . . . . . . See Transaxle Transmitter Battery Service (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 26 Transmitter, Garage Door Opener (HomeLink威) . . . . . . . . . . . . . . . . . . . . . . . . . . . 158 Transmitter Programming (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . .
INDEX 471 Warning Flasher, Hazard . . . . . . . . . . . . . . . . . . 352 Warning Lights (Instrument Cluster Description) . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . 6 Warranty Information . . . . . . . . . . . . . . . . . . . . . 446 Washer, Adding Fluid . . . . . . . . . . . . . . . . . . . . . 385 Washers, Windshield . . . . . . . . . . . . . . . . 151,153,385 Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
2009 Sebring convertible Chrysler LLC 81-026-0936 First Edition Printed in U.S.A.
