Table of contents 1. General informations .............................................................................................. 3 2. Operational setup ................................................................................................... 3 2.1 Charging........................................................................................................ 3 2.2 Installing the handlebar bracket..................................................................... 3 2.
Congratulations ! By purchasing the CicloNAVIC 50 you have acquired high-level GPS-datalogger with electronic compass and navigation function. 1. General informations The CicloNAVIC 50 is equipped with a GPS receiver and is so able to calculate and record distance and speed. With the program CicloGuide the recorded tours can be displayed on the PC. Additionally the CicloNAVIC 50 offers the possibility to reconstruct a tour (with a maximum of 50 waypoints) which was created on the PC.
For using it on the stem rotate the upper part of the bracket. Open the 4 screws, rotate it 90° to the left and assemble it again with the 4 sc rews (pict. B). Remove the protective tape from the underside of the handlebar bracket, place the handlebar bracket in the required position on the handlebar (or on the stem) and press it down slightly. Secure it with the cable ties 2.
3. Using the buttons 3.1 Overview 3.2 Button functions Button Option Function LR-Taste Press 3 sec. • Power on / off the CicloNavic 50 Press short • Backlight on / off Press short • Switch to next mode or display When in submenu: back to previous mode / display Press 3 sec. • Call up POI-menu Press short • Confirm / set function or setting Press 3 sec.
4. Usage The CicloNAVIC 50 has four different displays (modes). By short pressing LL-button you can switch from one mode (display) to the next mode (display). These modes are: • • • • Main mode Bike info mode 1 Bike info mode 2 Menu mode There are additionally three different sport modes (Walk mode, Bike mode, User mode), to optimize specific settings (e.g. memory interval for waypoints, turn radius and so on) of the CicloNAVIC 50 depending on the chosen kind of sport).
Functions: • • • • • • • • • Current speed Shows current speed in kilometer per hour (kph) or miles per hour (mph). Ride time Shows current riding time. Distance Shows current distance. Remaining distance Shows the still remaining distance to target point (during a navigation) Remaining ride time Shows the estimated remaining ride time to target point (during a navigation) Average speed Maximum speed Current altitude Shows the current altitude (meter/m or feet/ft).
4.3 Bike info mode 2 Appears after bike info mode 1 and shows more details of the tour. Like in bike info mode 1 it can show data of the last three tours. 4.4 Menu mode Appears after bike info mode 2. Here you can see the POIs, BackTracks (recorded tours), the via PC uploaded tour and theme navigations and also you can do all necessary settings (see chap. 5). Choose the requested function (with UR-button) and confirm with UL-button. Options: POI Shows all stored POIs (see chap. 4.6).
ROUTE PLAN Here you can choose a tour which you uploaded with the program CicloGuide. It shows the single waypoints (starting with the end point). If you want to navigate not to the end point, but to a milestone just choose the requested point by using UR-button and confirm with ULbutton. THEME NAVI Here you can choose special points (like POIs) which you can upload with the program CicloGuide. Useful e.g.
By using UR-button you can choose a symbol for this POI (you can use one symbol for more than one POI), by short pressing UL-button the current latitude/longitude is stored with date, time and the chosen POI symbol. There is a counter on the right side of the POI popup window, which shows the consecutive number of the POI. The stored POIs can be recalled in the menu mode for a (beeline) navigation. There all stored POIs are shown with their symbol and date/time.
4.8 Compass The CicloNAVIC 50 is equipped with an electronic compass, which is displayed by a digital compass ring in main mode. The cardinal directions are shown as N (= North), E (=East), S (=South) und W (=West). If the compass shows wrong directions it needs to be calibrated (see chap. 5). 4.9 Backlight The CicloNAVIC 50 has an integrated backlight. Short press of LR-button switches the backlight on and off.
SETTING Following settings can be done: CLEAR DATA Delete the recorded data. Options: POI Back Track Route Plan Theme Navi Choose data with UR-button, delete with short pressing UL-button. POWER MODE Settings for backlight and auto suspend can be done here. Backlight Select how backlight shall work. Manual Backlight is switched on and off by short press of LR-button. 10 sec 30 sec 60 sec Backlight is switched on by every button press and automatically switched off automatically after set time period.
CALIBRATION If the compass shows wrong directions it should be calibrated. Do this best when CicloNAVIC 50 is mounted on the bike or lays on an even base. Press short UL-button to start the calibration. Now rotate the CicloNAVIC 50 (resp. the bike) repeatedly slowly clockwise (resp. ride a closely circel with the bike). CicloNAVIC 50 shows main mode, but there are no cardinal directions shown in the display. When they appear, the calibration is ended. UNIT Choose between kilometer/meter and mile/feet.
20m 30m 40m 50m 100m LANGUAGE Choose your language.
6. Connect with PC / PC evaluation 6.1 Installation To install the program CicloGuide and the needed driver, insert CD and start installation of CicloGuide. Installation screen for CicloGuide appears. Follow the instructions on the screen, after installing the program it automatically installs the driver. Follow the instructions on the screen until installation is finished.
Now connect CicloNAVIC 50 and PC with the USB cable and CicloNAVIC 50 will be automatically recognized. 6.2 Using CicloGuide Double click the icon to start the program. Note: a connection with the internet is required to show the map. When CicloNAVIC 50 is already connected with the PC when you start the program, the corresponding ComPort is automatically recognized and will be shown in the bottom line of the program. In the upper line of the program you can find the regarding functions. 6.2.
- Select “Theme Destination”. - Creating new theme destination by editing category/subcategory and add interesting points into category by clicking on the Google map, an icon is shown to mark the location. - Destination editor will popup for data input, including title, category, subcategory and information. To create own categories, click to To transmit to CicloNAVIC 50 click to To store the table click to . .
6.2.2 POI Here you can transmit the recorded POIs from CicloNAVIC 50 to PC. For this click to , now the recorded POIs appear in the table. By clicking to a POI in the table the corresponding point is shown in the map. 6.2.3 Route Route plan is designed for long distance waypoints navigation, you can define waypoints in the route through Google map, then download it to CicloNAVIC 50 and navigate to destination by sequence or direct options. - Select “Route” in the menu.
6.2.4 Track During navigation, some interesting points may want to be recorded. Back Track feature in CicloNAVIC 50 provides this function to manually record the current location. In CicloGuide the menu “Track” is used to manage the recorded points in the route and after downloading from CicloNAVIC 50 , they can be saved as backup files. For this click to , the transmission to PC is started. You can see the recorded tours in the table and by clicking on the table you can see them in the map.
8. Trouble shooting Problem Cause / Elimination No display / no power Battery not charged - to charge connect device with PC Device not powered on - press LR-Taste 3 sec. to power on No GPS-signal - use outside in an open area - check whether high buildings obstruct the view - re-start the device - try a reset: for this press UR-, UL- and LLbutton simultaneously for 3 sec.
9. Guarantee We offer a guarantee for 2 years from the date of purchase on the CicloNAVIC 50. The guarantee is limited to material and processing faults. Broken transmitters, or damages of wasted parts of CicloNAVIC 50 are excluded from the guarantee. The guarantee is valid only if the computer, with accessories, has been handled and maintained carefully and according to operating instructions. The guarantee will take place through changes of or repairing the defective parts.
10. Technical Data Positioning times - cold-start - warm-start - hot-start - reaquisition time Backlight LCD resolution LCD viewing area Ambient temperature Power supply Power consumption Water resistance Supports WAAS / EGNOS Waypoints Route plan 35 seconds 32 seconds 2 seconds 2 seconds Yes 128 x 128 dots 29,9 mm x 29,3 mm - 10°C bis + 50°C 3,7V Li Polymer rechargable accu ~ 10 hours with GPS-navigation ~ 2 months if powered off Up to 0,6 bar Max. 100.000 waypoints (One tour can have max.
11. Guarantee certificate Sender: ___________________________________________________________________ Name, First name ___________________________________________________________________ Street, No.
Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems) This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
