Technical data

5
For a better reading in the following chapters the setting modes are fat
printed and the settings fat and italic.
SET BIKE1 / SET RAD1
Adjustment of bike-specific values, e.g. total distance, circumference,
unit and more for bike 1.
Choose with centre button.
To do these settings for bike 2, press right and left button short simul-
taneously in normal mode. CM 8.2 switches to bike 2, then enter again
setting mode (display then shows SET BIKE2/SET RAD2).
DAY DST / TAGES-DST
Adjustment of the daily distance
Default: 000.00 km
Range: 000,00 to 999,99 km or m
Set with right and left button, store with left button.
Here the daily distance can be adjusted, e.g. the point of starting a tour,
when using a printed tour-guide.
(This setting doesn’t change the total distance. Only really ridden kilo-
metres are counted).
TOT DST / GES. DST
Adjustment of the total distance
Default: 0000 km
Range: 0 to 99999 km or m.
Set with right and left button, store with left button.
Here the total distance can be adjusted.
Wheel/Radumf.
Adjustment of circumference
Default: 2080 mm
Range: 0000-3999 mm
Set with right and left button, store with left button.
Here the circumference can be adjusted.
Size Circumference
40-559 26 x 1,5 2026 mm
44-559 26 x 1,6 2051 mm
47-559 26 x 1,75 2070 mm
50-559 26 x 1,9 2026 mm
54-559 26 x 2,00 2089 mm
57-559 26 x 2,125 2114 mm
37-590 26 x 1 3/8 2133 mm
32-620 27 x 1 1/4 2199 mm
40-622 28 x 1,5 2224 mm
47-622 28 x 1,75 2268 mm
40-635 28 x 1 1/2 2265 mm
37-622 28 x 1 3/8 2205 mm
20-622 700 x 20C 2114 mm
23-622 700 x 23C 2133 mm
25-622 700 x 25C 2146 mm
28-622 700 x 28C 2149 mm
32-622 700 x 32C 2174 mm
The circumference of the wheel can be taken from the chart
(Pict. G) or be measured by yourself.
Measuring the circumference of the wheel (for a more precise setting):
Put a marking at the front-tire and on the ground (e.g. with chalk). Ride
straight ahead exactly one turn of a tire (for a very exact measurement,
check the pressure of the tire before getting on your bike) and mark this
position on the ground. Now measure the exact circumference of the
wheel between the two markings at the ground (in mm) – see pict. F.
Unit km bzw. Unit mi
Adjustment of the measuring unit (kilometres or miles)
Default: km
Set with right button, store with left button
Here you can choose whether the display should show kilometres
(km/h) or miles (m/h).
SPD INISCAN
To start this function, simultaneously press the left and right buttons
briefly, jump setting with left button.
To initialize the speed transmitter (for first use or after battery/trans-
mitter change):
First, activate the speed transmitter (by moving the magnet close to
the transmitter where marked) then press the left and right buttons
simultaneously. A percentage will be displayed in the upper display. If
transmitter has been initialized successfully, the next setting option will
be displayed.
If transmission could not be initialized (e.g. transmitter was not activa-
ted) “error” will be displayed in the upper display. By pressing the left
and right buttons simultaneously the search for the transmitter will be
started again, to jump this setting press left button.
CAD OFF/TRITT AUS
Switch cadence on/off (ON/AN – OFF/AUS)
Default: OFF/AUS
Set with right button, store with left button
Here you can switch on/off the cadence measuring. To use this function
you need the optional cadence-set (available at your local dealer).
CAD INISCAN
To start this function, simultaneously press the left and right buttons
briefly, jump setting with left button.
To initialize the cadence transmitter (for first use or after battery/trans-
mitter change):
First, activate the cadence transmitter (by moving the magnet close
to the transmitter where marked) then press the left and right buttons
simultaneously. A percentage will be displayed in the upper display. If
transmitter has been initialized successfully, the next setting option will
be displayed.
If transmission could not be initialized (e.g. transmitter was not activa-
ted) “error” will be displayed in the upper display. By pressing the left
and right buttons simultaneously the search for the transmitter will be
started again, to jump this setting press left button.
SET CLOCK / SET UHR
Adjustment of clock, date and clocktime-format.
Choose with centre button
Time / Uhrzeit
Adjustment of clock
Range: 00:00 to 23:59 or 12:00 to 11:59 A/P
Set with right and left button, store with left button
Here you can set the current clocktime. First you set the hours, then
the minutes.
Year / Jahr
Adjustment of the year
Default: 2007
Range: 2007 to 2099
Set with right button, store with left button
Here you can set the current year.
Month / Monat
Adjustment of the month
Default: 01
Range: 01 to 12
Set with right button, store with left button
Here you can set the current month.
Day / Tag
Adjustment of the day
Default: 01
Range: 01 to 31
Set with right button, store with left button
Here you can set the current day.