Technical data

6
Clock / Zeit
Adjustment of the clock format
Default: 24
Set with right button, store with left button
Here you can select between 24- or 12-hour format (AM/PM).
SET HR / SET HF
Adjustments for the optional heart rate measurement. To use this
function you need the optional heart rate-set (available at your local
dealer).
HR OFF/ON / HF EIN/AUS
Switch heart rate on/off (ON/AN – OFF/AUS)
Default: OFF/AUS
Set with right button, store with left button
Here you can switch on/off the heart rate measuring.
HR INISCAN
To start this function, simultaneously press the left and right buttons
briefly, jump setting with left button.
To initialize the heart rate transmitter (for first use or after battery/trans-
mitter change):
First, activate the heart rate transmitter (chap. 2.2) then press the left
and right buttons simultaneously. A percentage will be displayed in the
upper display. If transmitter has been initialized successfully, the next
setting option will be displayed.
If transmission could not be initialized (e.g. transmitter was not activa-
ted) “error” will be displayed in the upper display. By pressing the left
and right buttons simultaneously the search for the transmitter will be
started again, to jump this setting press left button.
Fitness / Fitness
Adjustment of the fitness level.
Default: 3
Set with right button, store with left button.
Range 1-4, corresponding to the following levels:
1 – low fitness
2 – average fitness
3 – good fitness
4 – high fitness
Here you set your personal fitness level, necessary for the CICLOInZone
®
-
calculation.
Sex / Geschlecht
Set with right button, store with left button.
Change between
m = male and f = female.
The sex is needed for the CICLOInZone
®
-calculation and the calorie
consumption.
Weight / Gewicht
Range: 20 to 220 kg
Set with right and left button, store with left button.
The weight is needed for the CICLOInZone
®
-calculation and the calorie
consumption.
Birthdate /Gebjahr
Adjust with right and left button, store with left button.
Default: 1960
Range: 1920 to 2006
The year of birth is necessary for the CICLOInZone
®
-calculation.
InZone
Here you can start the CICLOInZone
®
-calculation by short pressing
of right and left button simultaneously (see also chap. 4 for
CICLOInZone
®
).
In order to ignore the calculation, just press short left button.
In order to obtain an exact calculation of ones personal CICLOInZone
®
it is necessary to insert the personal data relative to fitness-level, sex,
weight and birthdate.
In order to calculate the CICLOInZone
®
position the chest belt correct-
ly, take up a rest position (remain seated and relaxed) and start the
CICLOInZone
®
calculation by short pressing of right and left button
simultaneously.
The CM 8.2 will then start to time 5 minutes. During this time, stay
seated, relaxed and calm, as the CM 8.2 will measure the minimum
heart rate reached during this period (heart rate at rest) and will store
this value for the subsequent calculation.
After the 5 minutes the lower value of the calculated personal
CICLOInZone
®
appears in the display.
Lower HR / untere HF
A lower heart rate limit can be set here or (after CICLOInZone
®
-calcula-
tion) the calculated value is shown.
When the current heart rate is lower than this value, the CM 8.2 shows
an arrow (t) as an optical alarm.
Range: 0 to 220 bpm
Adjust with right and left button, store with left button
Upper HR / obere HF
An upper heart rate limit can be set here or (after CICLOInZone
®
-
calculation) the calculated value is shown.
When the current heart rate is higher than this value, the CM 8.2 shows
an arrow as an optical alarm.
Range: 0 to 240 bpm
Adjust with right and left button, store with left button
Max HR / Max HF
Shows the maximum heart rate, calculated with CICLOInZone
®
.
Range: 0 to 240 bpm
Adjust with right and left button, store with left button
SET MISC
Here you can switch on the powerdown-mode or make a reset (delete
all values).
Choose with centre button
Powerdown / STROMSPAR
Switch on the powerdown-mode (e.g. before changing of the battery,
to save the values).
To switch it on, press right and left button short simultaneously, display
fades out and CM 8.2 is in powerdown-mode. By short pressing of any
button, CM 8.2 starts again and shows normal mode.
Reset / Löschen
Here you can delete all values (including the total values). For this press
right and left button short simultaneously, display shows ‘reset’ and
then normal mode.
If you only want to delete the day values only, simultaneously press all
three buttons for three seconds in normal mode.
PC-LINK
To start PC transmission.
Select with centre button.
LINK / VERBINDEN
If USB-Interface has been connected, start connection by pressing left
and right buttons simultaneously. For further actions, see chapter 7.