M-97RG2 Hardware Installation Manual ONT M-97RG2 Hardware Installation Manual Mar.2021 Rev.
M-97RG2 Hardware Installation Manual Notice The CIG name, the CIG logo, and all CIG product names are trademarks of Cambridge Industries Group Co. Ltd (CIG). All other brand and product names are trademarks of their respective holders. Specifications, products, and products names are subject to change without notice. Performance figures and data quoted in this document are typical and must be specifically confirmed in writing by CIG before they become applicable to any particular order or contract.
M-97RG2 Hardware Installation Manual Table of Contents Preface .............................................................................................................................................. 4 1.1. Basic Requirements ......................................................................................................................... 5 1.2. Environmental Requirements ........................................................................................................ 5 1.3.
M-97RG2 Hardware Installation Manual Preface About This Document This guide describes how to install the CIG Wi-Fi extender device unit (Gateway) at the customer premises. Intended Audience This document is intended for technicians responsible for: Unpacking and mounting the Gateway and power supply Connecting the Gateway to the MoCa2.
M-97RG2 Hardware Installation Manual Safety Please read and follow all warning notices and instructions marked on the product or included in its packaging, and observe all safety instructions listed in this manual. 1.1. Basic Requirements Install the device in a well-ventilated place that is not directly exposed to sunlight. Keep the device dry and prevent the device from coming into contact with other objects during storage, transportation, and operation of the device.
M-97RG2 Hardware Installation Manual 1.3. Electrical Safety Use the accessories delivered with the device, such as the power adapter, battery, etc.. The power supply voltage and current of the device must meet the requirements on the input voltage and current of the device, and provide current overload protection. Keep the power plug clean and dry to avoid electric shock or other hazards.
M-97RG2 Hardware Installation Manual Ensure that the device is kept out of the reach of children. Guard against risks such as children playing with the device or swallowing small parts of the device. 1.6. Instructions for Environment Protection Deposit the used devices and batteries at the specified recycling facility.
M-97RG2 Hardware Installation Manual Appearance of products and individual components, refer to Figure 1 Ethernet Interfaces MoCa2.5 Interface Power Switch Button Power Interface Figure 1 Interface Description Power 12 V DC power input interface, connecting to power adapter RESET Reset the Gateway LAN1/LAN2/LAN3/LAN4 RJ-45 10/100/1000 Base-T Ethernet Interface or 10/100 fast Ethernet Interface, connecting to PC or Set-Top-Box MoCa2.
M-97RG2 Hardware Installation Manual Auto-negotiation and MDI/MDIX auto-sensing Built-in layer-2 switch Advanced data features such as VLAN tag manipulation, classification, and filtering 2.2.2. Video The M-97RG2 supports video service delivered in form of data (by multicast or unicast). M-97RG2 supports IGMP snooping function.
M-97RG2 Hardware Installation Manual 3. Hardware Operation 3.1. Environmental Requirements The Gateway will operate in temperatures ranging from 0°C to 40°C, relatively humidity ranging from 5% to 95%. 3.2. Power Requirements The Gateway will be shipped with a universal power adaptor. However, before installation, check if the AC power input matches the specification printed on the power adaptor (input voltage, current, etc.
M-97RG2 Hardware Installation Manual 3.4. Uninstall the Gateway For uninstall the Gateway on the wall: 1. Plug out the cables connector. 2. If necessary, remove the screw on the brackets, and take off the brackets. For uninstall the Gateway on the desktop: 4. Plug out the cables connector. 4. Services enabled 4.1. Connecting Power For AC power supply 1. Plug the 2-pin 12V DC power connector of AC power connector to ONT AC power interface. 2.
M-97RG2 Hardware Installation Manual Pin Color Signal Pin Color Signal 3 Green/White Rx + 7 Brown/White BI- 4 Blue BI- 8 Brown BI- 5. Verify the Installation and Services 5.1. Verify the Installation Check LED states to verify Gateway status (Section 5.2). Services are not available until the Gateway is ranged and provisioned in the network. If services must be verified at the time of installation, refer to Section for additional instructions. 5.2.
M-97RG2 Hardware Installation Manual Verify that the NET LED lights green, indicating that the Gateway interface is operating normally. The Gateway is placed into service remotely through the OLT. Services to the Gateway are likely wise provisioned and turned up remotely through the MoCa2.5 network. If the NET LED lights green, indicating that the Gateway is communicating with the MoCa2.5 network, no further activation is necessary and you can proceed to Verifying Services. 5.3.
M-97RG2 Hardware Installation Manual Table4 Gateway Status LEDs description NO LED indicate 1 POWER 2 3 4 5 6 7 8 9 LAN1 LAN2 LAN3 LAN4 Status Describe Green/Solid Normal Off No power Green/Solid Active or Link Green/Flash data receive and transfer Off Not active Green/Solid Active or Link Green/Flash data receive and transfer Off Not active Green/Solid Active or Link Green/Flash data receive and transfer Off Not active Green/Solid Active or Link Green/Flash data
M-97RG2 Hardware Installation Manual Problem Possible Solutions Check whether the ON/OFF button on the rear „ panel is pressed. The PWR LED is off Check whether the power adapter matches the M-97RG2. Check whether the power connection is correct. Check whether the power connection is correct. Check whether the Ethernet cable is connected correctly. The LAN LED is off Check whether the indicator of the network adapter is on.
M-97RG2 Hardware Installation Manual —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules.
M-97RG2 Hardware Installation Manual Compliance with CE Marking Certification (Class B) The equipment was tested and found to comply with EN 62368-1:2014/A11:2017;EN62311:2008. The equipment is tested and only used with power adaptor included in the package. The equipment complies with the requirements according to the following standard: ETSI EN 300 386 V1.4.
M-97RG2 Hardware Installation Manual EN 61000-3-2:2006+A1:2009+A2:2009: Limits for harmonic current emissions (equipment input current <=16A per phase) EN 61000-3-3:2008: Limitation of voltage fluctuations and flicker in low-voltage supply systems for equipment with rated current <=16AAppendix B: Technical Support CIG offers technical support 24 hours a day, 7 days a week.
M-97RG2 Hardware Installation Manual Appendix C: Ordering To order CIG components and documents, contact your local sales representative, or contact CIG at the address, telephone, fax number or e-mail address. Address: 5/F, Building 8, 2388 ChenHang Road MinHang District Shanghai 201114, China Phone: +86 21 8023 3300 Fax: +86 21 8023 3300 Email:sales@cambridgeig.com Web URL:http://www.cambridgeig.
