1. Air Finder System Overview Air Finder Staff Alert Devices work with the Air Finder Precise Location Service, resulting in the Air Finder Staff Alert System.
Like APs, Gateways are installed at a hotel or other site to provide comprehensive and redundant Symphony Link coverage. This Symphony Link Network is an Internet of Things (oT) network service layer for all Access Points. Access Points communicate Alert messages to Gateways. When a Gateway receives an Alert message from an Access Point, it acknowledges to the Access Point that the message was received.
1. The Devices record the MAC ID and Received Signal Strength Indicator (RSI} of all received {or “heard”} Location Beacon advertisement messages during the scan interval. 2. These RSI values are processed by the Device's location algorithm. The algorithm also uses any historical location determinations to determine the current location. 3. The algorithm determines which LB the Device in closest proximity to.
2. Air Finder Power Cradle AC Power (WF-402C) a. Hardware Verification « Remove Air Finder Power Cradle AC Power (WF-402CB) from packaging. « Visibly inspect front and back of unit (see Images 1 and 2 below) = If not damaged, proceed to the next step. = If the unit has visible damage, do not install. Instead, immediately put unit aside and RMA.
= Where applicable remove center screw of outlet. For single duplex outlets only. o Insert Power Cradle AC Power into power outlet. (See Images 3 and 4 for verification of proper installation) = Where applicable, if center screw was removed from single duplex outlet, then secure the Power Cradle AC Power by inserting the provided “long” screw through the penetration between the outlets of the Power Cradle AC Power.
o After verification of the proper functioning of Power Cradle AC Power, then, if required, reinsert any other power cables. (See Image § for an example.) Image 5: Location Beacon AC Power with external power cable inserted. o Power Cradle AC Power has been successfully installed.
b. Power and Reset Conditions on Power Cradle AC Power o LED Behavior when unit is powered = LED to the left of "POWER" on the top of the device [see image 6 to the right} lights solid for 5 minutes when power is applied {or after a reset) to the unit. = After 5 minutes, LED shuts off. o Reset = There are two means of resetting the Power Cradle AC Power. This can be accomplished by unplugging and plugging the device in again, or by activating the Reset pin.
3. Air Finder Location Beacon AC Power (WF-402CB) a. Hardware Verification Remove Air Finder Location Beacon AC Power (WF-402CB) from packaging. Visibly inspect front and back of unit (see Images 6 and 7 below) If not damaged, proceed to the next step. If the unit has visible damage, do not install. Instead, immediately put unit aside and RMA.
Locate power outlet for powering Location Beacon AC Power If there are any power cables occupying one or both outlets to be covered by the Location Beacon AC Power, then remove any power cables, = Recall the outlet location of each power cable. = Where applicable remove center screw of outlet. For single duplex outlets only. o Insert Location Beacon AC Power into power outlet.
o After verification of the proper functioning of Location Beacon AC Power, then, if required, reinsert any other power cables. (See Image 1 for an example.) Image TI: Location Beacon AC Power with external power cable inserted. o Location Beacon AC Power has been successfully installed.
b. Power and Reset on Location Beacon AC Power o LED on Location Beacon AC Power = LED starts blinking when power is applied {or after a reset]. = See Image 12 to the right. The LED is to the left of the word POWER on the top of the Location Beacon AC Power device. = LED lights solid for 5 minutes when BLE connection to Access Point is successfully acquired (Le. registration completed). 1 After 5 minutes, LED shuts off.
a. Hardware Verification o Remove Air Finder Access Point (WF-402AP) from packaging. o Visibly inspect front and back of unit (see Images 13 and 14 below} = If not damaged, proceed to the next step. = If the unit has visible damage, do not install. Instead, immediately put unit aside and RMA.
o See Images 15 and 16 for verification of proper installation of Access Point. Image 15; Front view of Access Image 16: Side view of Access Point Point (left) attached to Power (left) attached Power Cradle AC Cradle AC Power (right) Power (right) o Verify proper functioning of Access Point by observing proper LED behavior of unit according to the Power and Reset Conditions described below in b.
b. Power and Reset Conditions on Access Point o LED Behavior when Access Point is powered « See Image 17 for view of the Access Point LED. = LED Labeled "SL" Success += LED starts boinking when power is applied (or after a reset}. = Lights solid for 5 minutes when SL back haul is successfully acquired (ie. registration through completed; ready to flow data). eo Afters minutes, LED shuts off.
= Find the slot underneath the Access Point. Insert the pen or paperclip into the circular opening. = While keeping the pen or paperclip inserted, pull the paperclip or pen gently away from the Power Cradle AC Power or the Location Beacon AC Power, This releases the attaching clip without breaking the Access Point or attachment. = After detaching the Access Point, reattach it. = When successfully reset, the device will return to the initial LED Behavior laid cut above ("LED Behavior when units powered”) 5.
o Identify location for installing Location Beacon. = Verify that Bracket can be installed in the location, o Verify that batteries are installed in the Location Beacon. Screw bracket into wall or other surface. Insert Location Beacon into bracket. {See Images 20 and 21 for verification of proper installation} Image 20: Front view of Location Image 21: Side view of Location Beacon (right) attached to bracket Beacon attached to bracket.
b. Power and Reset on Location Beacon AC Power o LED on Location Beacon = LED starts blinking when power is applied {or after a reset]. = See Image 22 to the right. The LED is to the left of the word POWER on the top of the Location Beacon AC Power device. = LED lights solid for 5 minutes when BLE connection to Access Point is successfully acquired (Le. registration completed). 1 After 5 minutes, LED shuts off.
o» Remove Air Finder Power Cradle DC Power (WF-402B} from packaging. o Visibly inspect front and back of unit (see Images 23 and 24 below) = If not damaged, proceed to the next step. = If the unit has visible damage, do not install. Instead, immediately put unit aside and RMA. Image 23: Front view of Power Cradle DC Power with Access Point attached Image 24: Rear view of Power Cradle DC Power with Access Point attached o Identify location for installing Power Cradle DC Power.
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna.