User manual
Table Of Contents
- About this manual
- What’s included
- Safety information
- Support information
- Hardware I/O
- Basic operation
- User Interface
- General notes about the user interface
- Main user interface (recording)
- Record start [record]
- Record stop [stop]
- Wired remote record start/stop [start][stop]
- Slate display [slate] Not currently enabled.
- Safe Frame Display [safe]
- Grid Display [grid]
- 100% Display [100%]
- Edge detection display [edge]
- Image Analysis [analysis]
- Highlight Clipping [clipping]
- Full Screen display [fullscreen]
- Full screen mode in main user interface [fullscreen]
- Full screen mode in main user interface [fullscreen]
- Full screen mode in playback interface. [fullscreen]
- Setup Menu Tabs [setup]
- Playback user interface [play]
- Playback user interface [play]
- Playback file manager [play]:[open]
- Touch screen lock [lock]
- Time Code Reset [TC reset]
- Settings and Status displays
- Playback user interface
- Setup Menu Tabs [setup]
- Input preferences tab [setup]:[input]
- Input preferences tab [setup]:[input]
- Signal input settings [setup]:[input] or {input status display}
- Valid input selections
- Application restart on settings change
- Application restart on settings change
- Input resolution
- Input frame rate
- Input pixel format
- Input video source
- Input audio source
- Input preview options
- Input codec, quality, and file format (wrapper) options
- Input preferences tab [setup]:[input]
- Folder manager tab [setup]:[files]
- Time code Preferences Tab [setup][TC]
- Time code Preferences Tab [setup][TC]
- Internally generated time code [gen]
- Save time code at end of session. [save TC]
- Generated drop frame time code [drop]
- Embedded SDI time code [SDI]
- Embedded SDI time code auto-record, generic [generic]
- Embedded SDI time code auto-record, VITC [future]
- ExSync hardware timecode module [ExSync]
- Hardware timecode module not found
- Time code offsets [offset +][offset -]
- Time code offsets [offset +][offset -]
- Time code display modes
- Show UTC or Local timecode [show UTC][show local]
- Time code Preferences Tab [setup][TC]
- Convert preferences tab [setup][convert]
- Update preferences tab [setup][update]
- General preferences tab [setup][prefs]
- Input preferences tab [setup]:[input]
- Appendices:
- Field Operating System Restore (“Factory Reset”) Instructions:
- Cinedeck Operating System Field Restore Disk Update instructions
- Cinedeck Bootable BIOS Update Disk Creation Instructions
- Breakout cable connections
- Cinedeck I/O Pin Definitions: Serial numbers 500 and higher.
- Setting up the docking station for use with the Cinedeck Extreme
- Care and feeding of SSD media
- Setting the battery meter COM port
- Codec installation on the MAC and PC
- Average data rates
SDI
Phones
play setup
fullscreen
clipping
analysis
edge
100%
grid
safe
slate
stop
record
lock reset
manhattan_aerial
next: reel3_015.mov
1080p YUV10
23.98
CineForm 1.1MB/frame 27.3MB/s
3GB
3GB
Frame
Fps
Codec
Media
Free
Remain
00:12:06:21
long
lat
alt
temp
-74.0715
40.416
51.166
72
Battery
last take
44%
3:22
If you have purchased licences for optional
software features, they must be activated in
the keys menu before they will be available.
To activate these features:
1) Open the keys menu from the [setup]:
[update] menu.
2) Select the desired feature.
3) email the request code to:
support@cinedeck.com
When you have received a reply with the
license code from support, enter the code
into the license code field using the keypad.
Adding feature license keys to the software
License keys challenge code entry
Troubleshooting the update process, contin-
ued.
If the error message, “no update.exe found”
appears:
1) ensure that the downloaded zip file has
“upd.exe” inside it.
2) If there is no “upd.exe”, check your anti-
virus settings to be sure that the file has not
been stripped from the update zip file on
download.
Update preferences tab [setup]:[update]
Update preferences tab, continued [setup][prefs]
keys
keys
update
back
request code: 0030 1d08 e1b3 0000 0000
5
a
f
10
6
b
del
2
7
c
3
8
d
4
9
e
input files TC conv prefs
FullStream 3D basic 3D advanced
update
toggle the features you need, send the request
code to support@cinedeck.com, then enter the
response code
back
request code: 0030 1d08 e1b3 0000 0000
5
a
f
10
6
b
del
2
7
c
3
8
d
4
9
e
input files TC conv prefs
FullStream 3D basic 3D advanced
update
toggle the features you need, send the request
code to support@cinedeck.com, then enter the
response code
No update.exe found
tap to dismiss