User manual
Table Of Contents
- About this manual
- What’s included
- Safety information
- Support information
- Hardware I/O
- Basic operation
- User Interface
- General notes about the user interface
- Main user interface (recording)
- Record start [record]
- Record stop [stop]
- Wired remote record start/stop [start][stop]
- Slate display [slate] Not currently enabled.
- Safe Frame Display [safe]
- Grid Display [grid]
- 100% Display [100%]
- Edge detection display [edge]
- Image Analysis [analysis]
- Highlight Clipping [clipping]
- Full Screen display [fullscreen]
- Full screen mode in main user interface [fullscreen]
- Full screen mode in main user interface [fullscreen]
- Full screen mode in playback interface. [fullscreen]
- Setup Menu Tabs [setup]
- Playback user interface [play]
- Playback user interface [play]
- Playback file manager [play]:[open]
- Touch screen lock [lock]
- Time Code Reset [TC reset]
- Settings and Status displays
- Playback user interface
- Setup Menu Tabs [setup]
- Input preferences tab [setup]:[input]
- Input preferences tab [setup]:[input]
- Signal input settings [setup]:[input] or {input status display}
- Valid input selections
- Application restart on settings change
- Application restart on settings change
- Input resolution
- Input frame rate
- Input pixel format
- Input video source
- Input audio source
- Input preview options
- Input codec, quality, and file format (wrapper) options
- Input preferences tab [setup]:[input]
- Folder manager tab [setup]:[files]
- Time code Preferences Tab [setup][TC]
- Time code Preferences Tab [setup][TC]
- Internally generated time code [gen]
- Save time code at end of session. [save TC]
- Generated drop frame time code [drop]
- Embedded SDI time code [SDI]
- Embedded SDI time code auto-record, generic [generic]
- Embedded SDI time code auto-record, VITC [future]
- ExSync hardware timecode module [ExSync]
- Hardware timecode module not found
- Time code offsets [offset +][offset -]
- Time code offsets [offset +][offset -]
- Time code display modes
- Show UTC or Local timecode [show UTC][show local]
- Time code Preferences Tab [setup][TC]
- Convert preferences tab [setup][convert]
- Update preferences tab [setup][update]
- General preferences tab [setup][prefs]
- Input preferences tab [setup]:[input]
- Appendices:
- Field Operating System Restore (“Factory Reset”) Instructions:
- Cinedeck Operating System Field Restore Disk Update instructions
- Cinedeck Bootable BIOS Update Disk Creation Instructions
- Breakout cable connections
- Cinedeck I/O Pin Definitions: Serial numbers 500 and higher.
- Setting up the docking station for use with the Cinedeck Extreme
- Care and feeding of SSD media
- Setting the battery meter COM port
- Codec installation on the MAC and PC
- Average data rates
Enables 3GB/s output on BNC output A (default, off)
Enables peak view instead of meter view in audio meters.
When on, allows delete or renaming of folders when empty, and take delete.
Enables true progressive (p) input rather than progressive segmented frame (psf)
Shows separate record/stop buttons in main UI. Turn off for remote record/stop.
Enables right-click program exit when mouse is plugged in.
Shows mouse pointer if desired. Generally used when a mouse is plugged in .
Enables thumbnail display in playback file manager.
Enables awareness of Garmin GPS devices if one is plugged in to the USB port
Stops record when dropped frames on input is detected (default, on)
Stops record when input loss is detected (default, on)
[3Gb/s out]
[peak vu]
[Disable safe]
[P not PsF]
[rec/stop]
[mouse exit]
[Mouse]
[clip]
[thumbs]
[GPS]
[grid]
[drop stop]
[loss stop]
[main]
General Preferences [setup]:[prefs]
General preferences tab [setup][prefs]
Displays general preferences page, shown above.
Opens grid and safe frame overlay preferences page.
Opens highlight clipping overlay preferences page
prefs
main
loss stop
drop stop
thumbs
rec/stop
disble safe
grid
grid
mouse exit
peak vu
P not Psf
mouse
3Gb/s out
clip
P not Psf
Peak vu
mouse exit
low
high
Digi View
exit app grid
clip
reset prefs
save prefs
load prefs
restart app
Anton Bauer
mouse
input files TC conv input
GPS
Disable Safe
3Gb/s out
3Gb/s out
drop stop fan ctrl
battery
meter
fan ctrl
mainloss stop
prefs
support@cinedeck.com Version 2.0 release build 2.177