360º VEHICLE SURROUND VIEW MONITORING SYSTEM MANUAL BOOK © 2017 Wireless Prime INC. All Rights Reserved.
Contents Introduction 2 Product Features 3 Specifications 4 Instructions 5 Installation Instructions Bus Installation Truck Installation Host Device Installation Remote Control Instructions Camera Calibration Calibration for Buses and Trucks Position Calibration Merging Calculation Function Settings Interface Settings Upgrade and Restore Other Settings Video Settings Video Recording Functions Smart Power Management 5 7 8 9 9 10 10 11 12 12 12 12 13 13 13 13 Disclaimers 15 About Wireless Prime 1
Introduction This guide is to provide users with an understanding of the system installation procedure, camera calibration steps, and interaction with the system menu. The VR3D Player 360º Vehicle Surround View Monitoring System synthesizes images from four cameras to create a true 3D view of a vehicle's surroundings. The technology enables flexible omni-directional monitoring around a vehicle from a dynamically definable perspective or "free eye point.
Product Features 4X 180º ultra-wide fish-eye cameras. Seamless video merging based on dual core ARM CPU and hardware high-efficiency acceleration engine. Choose between Arbitrary and dynamic 3D mode view angle for better view of surrounding environment. Independent fish-eye calibration parameter and algorithm for each camera. Pixel statistic engine for realtime brightness balance across four camera channels. 3D video de-interlacing and noise reduction technology for CVBS signal decoding.
Specifications TYPE Video Indicator Lamp /Blinker G-sensor Compression Disk Capacity Power Consumption Dimension SPECIFICATION Video Interface Mini plug connector Input / Output Impedance 75Ω Amplitude Typical 1Vpp, 1.2Vpp Maximum Bandwidth 8MHz Sampling Frequency 13.5MHz DP(Differential Phase) <0.8°TYP DG(Differential Gain) <3%TYP SNR 70dB High beam Optional Left/Right Turning Blinker Yes Reversing Lamp Yes BM250E Bosch Algorithm H.264 Baseline@L3.
Instructions Installation Instructions 1) Wire Routing Inside the Car Please refer to wiring diagram for more details. Please pay close attention to the color and connector size of each extending cable. Wire routing should be installed from cameras to the host device side. All the cables should be gathered to the host device side. 2) Camera Installation Please refer to the corresponding section for detailed installation steps.
Instructions 8) Device Fixing Fix the wire connections, cameras and host device. 9) Reconversion Recover all the parts of the vehicle. NOTE: Please install in cable extension kit in the proper order according to the vehicle length. Standard extension cable lengths are as listed: Front Camera: 4M*2 Rear Camera: 6.45M*2 Left Camera: 3.45M*2 Right Camera: 3.
Instructions Bus Installation 2 5 4 1 3 1 LCD Monitor 2 Front Camera 3 Rear Camera 4 Left Camera 5 Right Camera camera angle 0-45º © 2017 Wireless Prime INC. All Rights Reserved.
Instructions Truck Installation 3 4 5 2 1 1 LCD Monitor 2 Front Camera 3 Rear Camera 4 Left Camera 5 Right Camera camera angle 0-45º © 2017 Wireless Prime INC. All Rights Reserved.
Instructions Host Device Installation Instructions 1) Disassemble the panel of the central control unit, and connect the reversing video channel of the LCD monitor or other display screen(AV in). 2) For IR mode, put the infrared receiver in the proper position. 3) Please connect the anode of the left/right turning signal from the fuse box to the host wire harness, or from the side mirror turning LED indicator to the camera side of the extending cable.
Instructions Camera Calibration Press the "MODE" button on the remote controller to enter system menu settings. Select the correct calibration size for the applied vehicle model. If you are not sure about the sensor type, set each step of the shadow setting to 5cm as default. Calibration for Buses and Trucks Past the calibration tape around the vehicle as shown in the diagram. Please refer to the calibration pictures of different vehicle models and sizes to select the correct one for your vehicle.
Instructions Position Calibration There are 8 calibration points for each camera which need to be marked in the screen. The third pixel point and fourth calibration point are always the diagonal corner of the packing box. The packing boxes can be divided so that each packing box can be used for calibration 1 camera each time. NOTE: Put the 3 packing boxes in the correct position as illustrated in the previous diagram.
Instructions Merging Calculation Press “OK” to start image merging. Do not turn off the system during this operation, The system will reboot automatically after image merging is finished. Function Settings Menu Item List Options Description Turn Signal Wake Up ON/OFF Turning Signal is optional after engine is turned on. This option is a global switch for left and right turning indicators: when turned on, the system will respond when a turning event is triggered and vice versa.
Instructions Other Settings Menu Item List Options Description Hazard Blinker Trigger Duration 1min - 5min; 3S - 30S Display Turn Delay 30S - 5min This option is used to set the delay for the generated reversing indication signal to inform the monitor that the input video is ready. Trigger Delay 30S - 5min This option is used to set the latency to respond to the release event of the turning signal.
Instructions 3) Standby Mode In this mode the recording system is in standby. If any vibration is detected by the G-sensor, the SVM system will trigger the external cameras and LEDs and immediately begin recording video. 4) Power Off Mode In this mode the system is turned off except for the Real Time Clock chip and G-sensor. The system will still be triggered from vibration, except under circumstances where the battery life is under 11V. © 2017 Wireless Prime INC. All Rights Reserved.
Disclaimers Terms and Conditions Congratulations on purchasing your new WIRELESSPRIME product. Please read this manual carefully before using the product. By using this product, you hereby agree to this disclaimer and signify that you have read it in full. You agree that you are responsible for your own conduct and any content created while using WIRELESSPRIME products, and for any consequence thereof.
About Wireless Prime Inc. As Cinegears was founded in 2010 with the soul purpose in mind to drive video transmission technology to new heights and provide high quality professional grade products; so it was a natural progression to create Wireless Prime to help bridge the gap between the professional market and the consumer market. Enhancing your way of living while reducing the headache of everyday life is what Wireless Prime is here for.
