GHOST EYE 150M V2.6 WIRELESS HDMI/SDI VIDEO TRANSMISSION SYSTEM MANUAL BOOK © 2017Reserved. Cine Gears INC. All Rights Reserved. © 2018 Cine Gears INC.
Trademarks Ghost-Eye Wireless Video Transmission SystemsTM are trademarks of Cine Gears Inc. Web Interface. Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, Cine Gears Inc. reserves the right to make changes to the products described in this document without notice. Cine Gears Inc. does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.
Contents About the 150M Wireless Video Transmission System Features Receiver Diagram Transmitter Diagram Installation Troubleshooting Guide Warning Specification Disclaimers About Cinegears © 2018 Cine Gears INC. All Rights Reserved.
Features . Uses 5GHz ISM frequency band, maximum 10 frequency channels selection, coexist with WIFI. . Highest resolution supports color depth of up to 30 bits(10 bits/color), . HDMI and SD/HD/3G SDI input and output, HDMI & SDI cross conversion is supported. . Support wireless HD video(up to 1080P 60Hz) with no compression and no delay up to 300m(984ft). . Support point to point, and point to multi points network topology, . Support professional audio formats include Dolby True HD, DTS-master, etc. .
Receiver Diagram 1 7 2 3 LINK VIDEO SDI OUT RSSI CH ON/OFF HDMI OUT OK DC 7-36V 4 5 6 8 9 10 Receiver : 1:Video input indicator 6:Frequency display 2:Link status indicator 7:SDI output 3:RSSI 8:HDMI output 4:Frequency confirm button 9:Power on/off 5:Frequency selection button 10:DC input © 2018 Cine Gears INC. All Rights Reserved.
Transmitter Diagram 1 2 LINK VIDEO SDI IN CH HDMI IN OK 7-36 DC ON/OFF 3 4 5 6 7 8 9 Transmitter : 1:Video input indicator 6:SDI input 2:Link status indicator 7:HDMI input 3:Frequency display 8:Power on/off 4:Frequency selection button 9:DC input 5:Frequency confirm button © 2018 Cine Gears INC. All Rights Reserved.
Installation External Battery External Battery The best reception angel (transmitter and receiver face-to-face) Transmitter Receiver Lemo Cable Lemo Cable Suggest installing receiver 1.7+ meters high from ground Monitor Suggest installing receiver 2+ meters high from ground VIDEO OUT Cameraman Camera Director Ground © 2018 Cine Gears INC. All Rights Reserved.
Installation 1) Ensure the video source output of the camera is OK, and the HD monitor is powered on and switched to connected video input port. 2) Ensure 2 TX antennas are installed. For optimal results set the dual antennas in the form of a “V” and maintain unobstructed line of sight between transmitter and receiver. Below figure for your reference. LINK VIDEO CH OK 3) Ensure all input, output SDI or HDMI cables are connected.
Installation Installation 7)Before RX finished wireless link with TX, 5 RSSI indicators and VIDEO indicators are off; when wireless link is done, RSSI indicators will light first and indicate the signal strength. If the receiver detects wireless video normal internally from air inferface, VIDEO indicator will light. Before that, If SDI or HDMI video out port of the receiver has HD monitor connected, it will display an OSD of Link connecting…… as in the figure below.
Installation The wireless transmission system works in the 5.1-5.9GHz frequency band and can be flexibly configured to other licensed or ISM bands to accommodate different global regions. The front panel of the transmitter features a frequency selection button (see below illustration), which provides a maximum of 4 workable frequency channels, and supports a maximum of 4 simultaneous receiver units. LINK VIDEO RSSI Frequency selection button CH OK © 2018 Cine Gears INC. All Rights Reserved.
Troubleshooting Guide Step 1 The syst em can’t establish link The working distance can’t reach 150M 1 1 1 1 If the transmission system can’ t establish link at long distance but works well at shorter distance. Please check if the transmitter and receiver under specified working distance. And if the transmitter and receiver set at the same frequency. If established link at shor ter distance. Please check if the ant ennas ar e scr ewed tightly .
Warning ●Do not expose this device to extreme hot, cold, dusty or humid environments. ●Do not scratch the device with sharp objects. ●Do not drop this device from high place, as this may cause hardware damage. ●This device is designed for non-waterproofing. Please do not allow any liquid to penetrate into the device. ●Do not attempt to dismantle, open or repair this device yourself, as this may cause permanent damage to the device. © 2018 Cine Gears INC. All Rights Reserved.
Specification Transmitter Int er face SDI Input(BN C female); H DM I Input(Type A female); 2 Antenna port(R P- SM A male); DC input(4pin LEM O female) Receiver SD I O utput(BN C fem ale); H D M I O utput(Type A fem ale); D C input(4pin LEM O fem ale) 7-36V DC 7-36V DC Transmission Range up to 300 meters/984 ft up to 300 meters /984 ft Power Consumption <6.5W <6W (L x W x H): 67*122.2*25.3mm (L x W x H): 95.4*152.
Disclaimers FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Disclaimers Terms and Conditions Congratulations on purchasing your new CINEGEARS product. Please read this manual carefully before using the product. By using this product, you hereby agree to this disclaimer and signify that you have read it in full. You agree that you are responsible for your own conduct and any content created while using CINEGEARS products, and for any consequence thereof.
About Cinegears Cine Gears Inc. is an industry leading company that designs and manufactures digital wireless follow focus systems, lens control systems, camera motion control systems and accessories for film and broadcast industry. As a big believer in the power of creativity and ideas, we designed the Pegasus cablecam, the wireless motor drive that integrated a built in wireless transmitter, and the wireless finger wheel controller. The Cine Gears Inc.