Manualshelf

User Manual

ManualsBrandsCINEGEARS ManualsCamcorder & Camera PeripheralsFull HD Wireless Video Transmission Kit
11121314151617181920
© 2018 Wireless Prime INC. All Rights Reserved.
Functional Instructions
VIDEO
4
VIDEO
3
VIDEO
2
VIDEO
1
CH2
RX:3060
15
16
1
2
3
4
5
6
J16
PHONEJACK STEREO SW
RCLamp0521PA
D13
D12
RCLamp0521PA
Tally_Red
Tally_Green
Transmitter ID
Frequency Channel
Video
Signal Icon
Transmitter ID
Four transmitters are numbered 1, 2, 3
and 4, respectively
Video
No video signal received from TX
VIDEO
Video signal received from TX
CH*
Icon
Content
Status
Frequency Channel
Numbers 1~4
Blank
Display current frequency channel (1~11)
Signal Icon
X
Signal bar
Successful network connection
Connecting
Functional Instructions
Tally function
Insert the Tally light into the transmitter’s Tally output interface first,
then connect the to the receiver’s Tally input interface,
and then control the Tally light of the four transmitters through the switch
console. When the receiver is triggered by a low-level current,
the transmitter’s Tally light is on.
switch console
Tally interface of the transmitter and receiver: The transmitter’s Tally
interface is a standard φ3.5 headphone interface. The receiver’s Tally
interface is a DB9 female.
Tally light output interface:
The DB9 heade
r of the Tally input interface is
defined as follows:
WPS L
Gain State
Low gain mode
L
High gain mode
WPS
WPS
WPS Pairing
Blank
Blank
Standard work mode
VIDEO
4
VIDEO
3
VIDEO
2
VIDEO
1
CH2
RX:3060
15
16
1
2
3
4
5
6
J16
PHONEJACK STEREO SW
RCLamp0521PA
D13
D12
RCLamp0521PA
Tally_Red
Tally_Green
Transmitter ID
Frequency Channel
Video
Signal Icon
Transmitter ID
Four transmitters are numbered 1, 2, 3
and 4, respectively
Video
No video signal received from TX
VIDEO
Video signal received from TX
CH*
Icon
Content
Status
Frequency Channel
Numbers 1~4
Blank
Display current frequency channel (1~11)
Signal Icon
X
Signal bar
Successful network connection
Connecting
Functional Instructions
Tally function
Insert the Tally light into the transmitter’s Tally output interface first,
then connect the to the receiver’s Tally input interface,
and then control the Tally light of the four transmitters through the switch
console. When the receiver is triggered by a low-level current,
the transmitter’s Tally light is on.
switch console
Tally interface of the transmitter and receiver: The transmitter’s Tally
interface is a standard φ3.5 headphone interface. The receiver’s Tally
interface is a DB9 female.
Tally light output interface:
The DB9 header of the Tally input interface is
defined as follows:
WPS L
Gain State
Low gain mode
L
High gain mode
WPS
WPS
WPS Pairing
Blank
Blank
Standard work mode
16
Functional Instructions
15
16
1
2
3
4
5
6
J16
PHONEJACK STEREO SW
RCLamp0521PA
D13
D12
RCLamp0521PA
Tally_Red
Tally_Green
Transmitter ID
Four transmitters are numbered 1, 2,
respectively
Video
No video signal received from TX
VIDEO
Video signal received from TX
CH*
Icon
Content
Status
Frequency Channel
Numbers 1~2
Blank
Display current frequency channel (1~11)
Signal Icon
X
Signal bar
Successful network connection
Connecting
Functional Instructions
Tally function
Insert the Tally light into the transmitter’s Tally output interface first,
then connect the to the receiver’s Tally input interface,
and then control the Tally light of the four transmitters through the switch
console. When the receiver is triggered by a low-level current,
the transmitter’s Tally light is on.
switch console
Tally interface of the transmitter and receiver: The transmitter’s Tally
interface is a standard φ3.5 headphone interface. The receiver’s Tally
interface is a DB9 female.
Tally light output interface:
Gain State
Low gain mode
L
High gain mode
WPS
WPS
WPS Pairing
Blank
Blank
Standard work mode
RX:3062
VIDEO
2
VIDEO
1
CH2 WPS L
Frequency point
Signal Icon
Video
Transmitter ID