User Guide Revision 1.1 — November, 2014 Information and specifications in this document are subject to change without notice. w w w. c i n e o l i g h t i n g .
Welcome to Cineo Maverick Cineo Lighting has developed the versatile Cineo Maverick Remote Phosphor light source. Maverick operates from many power options, including AC, DC and battery power. The power connection uses an industrystandard XLR4 connector with an input voltage range of 10.8 to 28 VDC. Like all Cineo soft lights, Maverick allows the user to change the Remote Phosphor panels, supporting CCT of 2700K, 3200K, 4300K, 5600K, 6500K, Chroma Blue and Green.
General Notes 1. Please read through this manual carefully before operating Cineo Maverick, and keep this manual for future reference. 2. There are numerous safety instructions and warnings that must be adhered to for your own safety. 3. Maverick is not intended for residential use. It is intended for use in a professional studio. 4. Maverick service must be performed by a qualified technician. 5. Although Maverick is weather-resistant, the fixture is intended primarily for indoor use. 6.
System Components, Connections and Controls Maverick Lamphead The Maverick lamphead represents the next generation of Remote Phosphor professional lighting, incorporating simple operation, advanced passive cooling and versatile configuration options. Local 0-100% dimming is facilitated with a simple rotary control, while adding the DMX module provides remote control of the fixture. Maverick can be configured to run on battery, DC or AC power sources.
Maverick Power Sources The Maverick fixture features SmartPower™ power control, allowing operation with any 1224VDC power source capable of delivering 75 -150 watts. This provides compatibility with a wide range of battery and AC options. Configuration of SmartPower is covered in detail in the Advanced Power Setting section of this guide. Cineo offers the following power accessories for mounting on the either the Maverick yoke or BackPak™ accessory bracket.
Advanced Power Settings SmartPower settings are configured on a set of DIP switches located inside the lamphead. By placing these switches inside the fixture, misuse of various power configurations is minimized, as the fixture should be set up with the power sources intended for use in mind. To access the switches, you must remove the lower panel from the lamphead.
High Voltage setting (HV) The Maverick fi xture is designed for use with a 24VDC AC adapter when used on house power. The HV switch allows the fi xture to be confi gured for use at 120 watts or up to 135 watts, depending on the application. For portable use, Cineo provides a small, lightweight AC adapter, capable of operating from 90-240 VAC, with a 24VDC output of 120 watts.
DMX Module Operation When the DMX module is connected to the Maverick fixture, control of the fixture is automatically switched to the module. The DMX module has a multi-line display screen that indicates the firmware level, control mode (local / remote) and DMX address. The module is programmed by the use of four capacitive-touch buttons below the screen (-, +, Mode, Save). There are two control modes: one for determining local or DMX control, and one for setting the DMX address (0 – 255).
2. Remove the RP panel by sliding it up and out of the fixture. If the lamp is on, the output will be cut when the panel is removed. 3. Insert a new panel into the slots and firmly seat it into the bottom of the slot. If power is applied, the lamp will turn on. 4. Replace the top plate, tightening the two thumbscrews finger-tight. Although no harmful UV emanates from the fixture, Maverick should only be used with the remote phosphor panels in place.
For example, a studio lighting installation is best configured with the 150 watt power supply and DMX adapter attached to opposite sides of the yoke. For portable applications, the BackPak is an ideal mounting tool for one or two battery plates, or a battery plate and a 120 watt portable AC adapter. To remove / install the yoke: 1. Position the yoke 90º to the body of the fixture 2. With a #2 Phillips screwdriver, loosen the (4) mounting screws approximately one revolution 3.
Specifications Lamphead Input voltage: 10.5-28 VDC Power consumption: 75 watts / 120 watts / 135 watts (user configurable) 4-pin XLR power input EtherCon DMX port Completely silent, flicker-free operation Fixture dimensions: 9.4” x 7.3” x 3” (240mm x 186mm x 78mm) Weight: 2.2 kg (4.9 lbs) Maximum output: 8,000 lumens Beam Angle: >160º Max. temperature rise: +45° C above ambient Environmental temperature range: -20 - +50 C 35,000 hr.
150w AC Adapter Part # 900.0195 Input Voltage: 100-240VAC Output Voltage: 24VDC Max. output current: 6.25A Output connector: XLR4 Dimensions: 6.5” x 3.25” x 1.58 (165.1mm x 82.8mm x 40.1mm) Weight: 2.25 lb. (1.0 kg) 2-year parts and labor warranty UL, cULus and CE listed Input Voltage: 100-240VAC Output Voltage: 24VDC, 6.25A 900.0086 V-Lock Battery Plate Max output current: 10A Output connector: XLR4 Dimensions: 5.6” x 3.2” x 1” (142.1mm x 82.3mm x 26.3mm) Weight: 13 oz. (368.5 g) 900.
Warnings, Disclaimers and Warranty Burning Injuries Be aware of high temperatures in excess of 50ºC inside the lamphead during and after fixture use. To avoid burning injuries, do not touch the LEDs. Flammable Materials Keep flammable materials away from the installation. Ensure that the amount of air flow required for safe operation of the equipment is not compromised. Proper ventilation must be provided. ESD and LED’s LED components used in Maverick are ESD (Electro-Static Discharge) sensitive.
CINEO LIGHTING LIMITED WARRANTY Products from Cineo Lighting are warranted against defects in materials and workmanship for two years from the date the Product is shipped to Customer. Products are guaranteed to perform substantially in accordance with the accompanying written materials within the warranty period under normal use.
Specifications are subject to change without notice. Cineo Lighting, Cineo Maverick and Maverick are registered trademarks of Cineo Lighting, Inc. ©2014 Cineo Lighting, Inc. v11.06.14 Cineo Lighting P.O. Box 808 El Granada, CA 94018 Silicon Valley | Los Angeles | London info@cineolighting.com +1 310.425.3425 w w w. c i n e o l i g h t i n g .