Specifications
Table Of Contents
- Contents
- Tables
- Figures
- 1 Introduction
- 2 Interface Characteristics
- 2.1 Application Interface
- 2.2 RF Antenna Interface
- 2.3 GNSS Interface
- 2.4 Sample Application
- 3 Operating Characteristics
- 3.1 Operating Modes
- 3.2 Power Up/Power Down Scenarios
- 3.3 Power Saving
- 3.4 Power Supply
- 3.5 Operating Temperatures
- 3.6 Electrostatic Discharge
- 3.7 Blocking against RF on Interface Lines
- 3.8 Reliability Characteristics
- 4 Mechanical Dimensions, Mounting and Packaging
- 4.1 Mechanical Dimensions of TX62-W
- 4.2 Mechanical Dimensions of TX82-W, TX82-W-B, TX62-W-B and TX62-W-C
- 4.3 Mounting TX62/TX82 onto the Application Platform
- 4.4 Packaging
- 5 Regulatory and Type Approval Information
- 6 Document Information
- 7 Appendix
Cinterion
®
TX62-W/TX82-W Hardware Interface Description
2.1 Application Interface
73
t TX62-W_TX62-W-x_TX82-W-x_HID_v01.200d 2022-09-08
Public / Preliminary
Page 31 of 170
I
2
C I2CDAT I/O No internal pull up resistors
V
OL
max = 0.45V at Imax = -4.5mA
V
OH
max = 1.95V
V
IL
max = 0.5V
V
IH
min = 1.3V
V
IH
max = 1.95V
Note: Imax = I max external + I pull up
If unused keep lines
open.
Compatible with I
2
C Bus
Specification Version 5.0.
Multimaster is not sup-
ported.
The value of the pull-up
depends on the capaci-
tive load of the whole sys-
tem (I
2
C Slave + lines).
Only available with
embedded processing
option.
I2CCLK O
GPIO GPIO6-GPIO7,
GPIO20-GPIO23,
GPIO25
I/O V
OL
max = 0.45V at I = 4.5 mA
V
OH
min = 1.20V at I = 2.5 mA
V
OH
max = 1.95V
V
IL
max = 0.5V
V
IH
min = 1.3V
V
IH
max = 1.95V
If unused keep lines
open.
GPIO6 only available on
TX82-W, TX82-W-B,
TX62-W-B and TX62-W-C.
Further GPIOs shared
with other functions are
available with embedded
processing option (see
Section 2.1.8).
SPI SPI_CLK O
V
OL
max = 0.45V at I = 4.5mA
V
OH
min = 1.20V at I = 2.5mA
V
OH
max = 1.95V
V
IL
max = 0.5V
V
IH
min = 1.3V
V
IH
max = 1.95V
Shared with ASC1 func-
tion (see Section 2.1.8).
Only available with
embedded processing
option.
SPI_MOSI O
SPI_MISO I
SPI_CS O
ADC
(Analog-to-
Digital Con-
verter)
ADC1 I R
I
= 10MΩ
V
I
= 0.1V ... 1.875V (valid range)
V
IH
max = 1.910V
Resolution 64.979uV
If unused keep line open.
SUSPEND
mode indi-
cator
SUSPEND_
MON
OV
OL
max = 0.45V at I = 4.5 mA
V
OH
min = 1.20V at I = 2.5 mA
V
OH
max = 1.95V
High=Normal mode,
Low=SUSPEND mode.
If unused keep lines
open.
1. Thales strongly recommends to provide test points for certain signal lines to and from the module while
developing SMT applications – for debug, test and/or trace purposes during the manufacturing process.
In this way it is possible to detect soldering (and other) problems. Please refer to [5] and [6] for more in-
formation on test points and how to implement them. The signal lines for which test points should be pro-
vided for are marked as “Test point recommended“ in the above table.
Table 4: Signal properties
Function Signal name IO Signal form and level Comment