662 L/1664 BT Barcode Scanner Setup barcodes included. Version 2.
Copyright © 2011~2012 CIPHERLAB CO., LTD. All rights reserved The software contains proprietary information of CIPHERLAB CO., LTD.; it is provided under a license agreement containing restrictions on use and disclosure and is also protected by copyright law. Reverse engineering of the software is prohibited. Due to continued product development this information may change without notice.
FOR USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
FOR HAND-HELD PRODUCT WITH RF FUNCTIONS The 1662 L / 1664 unit (FCC ID, 1662 L : Q3N-1662; 1664 :Q3N-1664 ) complies with FCC radiation exposure limits set forth for uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. The unit has very low level of RF energy that it is deemed to comply without testing of specific absorption ratio (SAR).
RELEASE NOTES Version Date Notes 2.00 Mar. 20, 2012 Add: 1662 L model and Set Up Drivers License 1.03 Feb. 06, 2012 Add: Chapter 6 Fields of Time Stamp 1.02 Jan. 11, 2012 Modified: Specifications: Dimension and Weight description 1.01 Dec. 28, 2011 Add: 1.1.2 add delay note for activating the scanner from power off mode 1.00 Nov.
CONTENTS IMPORTANT NOTICES ................................................................................ - 2 For USA .............................................................................................. - 3 For Canada.......................................................................................... - 3 For Hand-held Product with RF Functions ..................................................... - 4 For Product with Laser ...................................................................
1662 L/1664 Barcode Scanner User Guide 1.4 Beeper ............................................................................................ 33 1.4.1 Beeper Volume ............................................................................ 34 1.4.2 Good Read Beep ........................................................................... 35 1.4.3 Low Battery Alarm ........................................................................ 36 1.5 Vibrator .....................................................
1662 L/1664 Barcode Scanner User Guide 2.2.1 Activate Bluetooth® SPP Slave Mode ................................................... 68 2.2.2 Inter-Function Delay ...................................................................... 68 2.2.3 ACK/NAK Timeout ........................................................................ 69 2.3 Bluetooth® SPP Master ......................................................................... 70 2.3.1 Activate Bluetooth® SPP Master Mode .................................
INTRODUCTION CipherLab’s small-form-factor 1600 Series Barcode Scanners are specifically designed to answer the mobile demands. The palm-sized scanners are designed to help accelerate productivity while lowering the total cost of ownership. Intensive data collection jobs are made easier with fast, accurate barcode scanning in various working environments, especially in small businesses.
1662 L/1664 Barcode Scanner User Guide GET FAMILIARIZED WITH 1662 L/1664 AND 3610 INSTALL THE BATTERY INTO 1662 L/1664 1) Hold the scanner face down in one hand, press the battery cover, and slide the battery cover. 2) Remove the battery cover. 3) Push battery lock to unlocked position. 4) Insert the battery into the battery compartment. Install the supplied 3.7V/850mAh Li-ion battery into the battery compartment. 5) Push battery lock to lock the battery firmly. 6) Replace the battery cover.
Introduction Note: (1) To turn off the scanner, press the [Power/Delete] key for 2 seconds. The scanner will respond with two short beeps (high tone) and the LED will become solid red. Release the key. Otherwise, let the scanner turn off automatically in (2) specific circumstances. Refer to settings of “Auto Power Off”. For shipping and storage purposes, remove the battery from the scanner. This will keep the batteries in good condition for future use.
1662 L/1664 Barcode Scanner User Guide CHARGE THE BATTERY VIA CHARGER The battery charger is provided for charging the battery outside of the scanner. You may purchase the charger separately. It takes approximately 3 hours to charge the battery to full. Note: Battery charging stops when the temperature drops below 0°C or exceeds 40°C. It is recommended to charge the battery at room temperature (18°C to 25°C) for optimal performance. 1) Insert the battery. 2) Connect the power supply cord to the charger.
Introduction USE 3610 The CipherLab Dongle (3610) is specifically designed for the scanner to communicate with a host computer cordless. The connection between the scanners and 3610 is made easy and reliable. Refer to 3.1.1 Connect to 3610. There is one LED indicator provided for communications status.
62 L/1664 Barcode Scanner User Guide INSIDE THE PACKAGE The items included in the package may be different, depending on your order. Save the box and packaging material for future use in case you need to store or ship the scanner.
Introduction SYMBOLOGIES SUPPORTED Most of the popular barcode symbologies are supported, as listed below. Each can be individually enabled or disabled. The scanner will automatically discriminate and recognize all the symbologies that are enabled.
1662 L/1664 Barcode Scanner User Guide GS1 DataBar Stacked Omnidirectional Composite Code Postal Code 2D Symbologies Disabled GS1 DataBar Limited (RSS Limited) Disabled Disabled GS1 DataBar Expanded (RSS Expanded) Disabled Disabled GS1 DataBar Expanded Stacked Disabled Composite CC-A/B Disabled Composite CC-C Disabled Composite TLC-39 Disabled US Postnet Enabled US Planet Enabled UK Postal Enabled Japan Postal Enabled Australian Postal Enabled Dutch Postal Enabled USPS 4CB/One
QUICK START The configuration of the scanner can be done by reading the setup barcodes contained in this manual or via the ScanMaster software. This section describes the procedure of configuring the scanner by reading the setup barcodes and provides some examples for demonstration. Configuration Mode 1) Hold down the [Power/Delete] key for 2 seconds to turn on the scanner. It will respond with a long beep and its LED will come on-off. 2) Read the “Enter Setup” barcode.
1662 L/1664 Barcode Scanner User Guide Working Mode Upon powering up, the scanner will try to establish a connection with 3610 or a computer with Bluetooth® wireless technology. Refer to Chapter 3 - Set up a WPAN Connection for details. The connection between the scanners and 3610 is made easy and reliable. Now, it also supports Bluetooth® SPP Master Mode as an alternative. Refer to 2.3 Bluetooth® SPP Master.
Quick Start ENTER CONFIGURATION MODE For the scanner to enter the configuration mode, read the "Enter Setup" barcode, which can be located at the bottom of almost every even page of this manual. The scanner will respond with six beeps and its LED indicator will become flashing red after reading the barcode. Enter Setup For configuring scanner parameters, see “Read a Setup Barcode” below.
1662 L/1664 Barcode Scanner User Guide DEFAULT SETTINGS SAVE USER SETTINGS AS DEFAULTS For the scanner to keep the customized settings as user defaults, you must read the “Save as User Defaults” barcode. This is a normal setup barcode, and the scanner will respond with two beeps (low-high tone). After reading the “Update” barcode, the current settings will be saved as user defaults.
Quick Start READ A SETUP BARCODE CONFIGURE PARAMETERS For most of the scanner parameters, only one read is required to set them to new values. The scanner will respond with two beeps (low-high tone) when each parameter is set successfully. Refer to Create One-Scan Setup Barcodes. But for a number of special parameters, multiple reads are required to complete the setting. In this case, the scanner will respond with a short beep to indicate it needs to read more setup barcodes.
1662 L/1664 Barcode Scanner User Guide The example below shows how to save your settings as “User Default” so that you may restore user defaults at a later time: Steps Action User Feedback if Successful 1) Power on the scanner… The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off. 2) Enter the Configuration Mode… The scanner will respond with six beeps (high-low tone repeats three times), and its LED indicator will be flashing red.
Quick Start The example below shows how to set numeric parameters: Steps Action User Feedback if Successful 1) Power on the scanner... The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off. 2) Enter the Configuration Mode… The scanner will respond with six beeps (high-low tone repeats three times), and its LED indicator will become flashing red. 3) Read a Setup barcode...
1662 L/1664 Barcode Scanner User Guide The example below shows how to set string parameters: Steps Action User Feedback if Successful 1) Power on the scanner... The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off. 2) Enter the Configuration Mode… The scanner will respond with six beeps (high-low tone repeats three times), and its LED indicator will become flashing red. 3) Read a Setup barcode...
Quick Start LIST THE CURRENT SETTINGS The current settings of all scanner parameters can be sent to the host computer for user inspection. The listing includes pages as shown below. You can select the page of interest by having the scanner read the “List Page x” barcode. The scanner will respond with two beeps (low-high tone) and send the selected page to the host immediately.
1662 L/1664 Barcode Scanner User Guide Reserved List Page 10 List settings regarding Editing Format 1 (1/2) List Page 11 List settings regarding Editing Format 1 (2/2) List Page 12 List settings regarding Editing Format 2 (1/2) List Page 13 List settings regarding Editing Format 2 (2/2) List Page 14 List settings regarding Editing Format 3 (1/2) List Page 15 List settings regarding Editing Format 3 (2/2) List Page 16 List settings regarding Editing Format 4 (1/2) List Page 17 List settings re
Quick Start List information regarding Driver License List Page 22 CREATE ONE-SCAN SETUP BARCODES The fact is most of the scanner parameters require only one read for setting new values. To facilitate configuring the scanner, you may create One-Scan setup barcodes for use.
1662 L/1664 Barcode Scanner User Guide Update Now, it requires only one read: One-Scan Setup Barcode for 109952 Note: The scanner will restart automatically upon reading the One-Scan setup barcode for (1) changing the interface or (2) setting memory mode, enable or disable. It will respond with a long beep and its LED will come on-off.
Quick Start 21 Update
Chapter 1 UNDERSTANDING THE BARCODE SCANNER This chapter explains the features and usage of the barcode scanner. IN THIS CHAPTER 1.1 Battery ..................................................................... 1.2 Memory .................................................................... 1.3 LED Indicator ............................................................ 1.4 Beeper ..................................................................... 1.5 Vibrator ...............................................
1662 L/1664 Barcode Scanner User Guide 1.1.1 HOW TO OPERATE THE SCANNER Turn on the scanner… Press the [Power/Delete] key for 2 seconds. The scanner will respond with a long beep (high tone), and its LED indicator will become solid red and go off. Turn off the scanner… Press the [Power/Delete] key for 2 seconds. The scanner will respond with two short beeps (high tone) and the LED will become solid red. Release the key then. Otherwise, let the scanner turn off automatically in specific circumstances.
Chapter 1 Understanding the Barcode Scanner 1.1.2 AUTO POWER OFF & POWER-SAVING The scanner will stay active at power-on, which may be followed by a transition from full CPU speed to low CPU speed (Power-Saving) to auto shutdown (Auto Power Off). Power-Saving (1~254 min.; 0= Disable): By default, it is set to stand by at full-speed for 2 minutes before it enters low-speed mode. If this feature is not desired, set it to 0. Auto Power Off (1~254 min.
1662 L/1664 Barcode Scanner User Guide After establishing a WPAN connection successfully… 1) Once a WPAN connection is established successfully, the scanner will stay active for a specified period of time (2 minutes by default) for data transmission. Its CPU is running at full speed, and the LED is flashing blue (On/Off ratio 0.02 s: 3 s). 2) If it is idle within 2 minutes, the scanner will become inactive to save power for the remaining period of time (the specified value minus 2 minutes).
Chapter 1 Understanding the Barcode Scanner Auto Off after 0~254 min. (*10) 1) Read the barcode above to specify the time interval in minutes before the scanner automatically turns off. 2) Read the “Decimal Value” barcode on page 錯誤! 尚未定義書籤。. For example, read “1” and “5” for the scanner to automatically turn off after being idle for 15 minutes. 3) Read the “Validate” barcode on the same page to complete this setting.
1662 L/1664 Barcode Scanner User Guide 1.2 MEMORY The scanned data can be sent to a host computer immediately via the WPAN connection or stored in flash memory when the scanner is set to Memory mode. 1.2.1 TRANSMIT BUFFER By default, the transmit buffer is enabled and ready for use when the scanner is out of range. Upon reading a barcode successfully within range, the scanner responds with one short beep (high tone) and its LED indicator becomes solid green and goes off.
Chapter 1 Understanding the Barcode Scanner 1.2.2 MEMORY MODE When the scanner is in memory mode, it means any real-time connection established with the host is disabled. 1662 L/1664 scanner keeps 4MB flash memory for memory mode operation, which can store over 240,000 scans based on EAN-13 barcodes. Enable *Disable Warning: No real-time connection is allowed unless the memory mode is disabled. Memory Data Delay You may set a delay between each data record while transmitting data back to the host.
1662 L/1664 Barcode Scanner User Guide 8 sec Send Data When the memory is used up, the scanner will respond with two short beeps (high-low tone) as a warning. It is advised to send data to the host immediately by having the scanner read the “Send Data” barcode below. 1662 L/1664 can send data via “Direct USB” interface once the computer has found the USB connection. Refer to 1.13 Use Direct USB Cable.
Chapter 1 Understanding the Barcode Scanner 1.3 LED INDICATOR The triple-color LED on top of the scanner is used to provide user feedback. For example, the LED becomes solid red and goes off upon powering on or running out of transmit buffer. You may tell the difference by the beeps – you will hear a long beep of high tone when powering on the scanner, and a long beep of low tone when the transmit buffer becomes full.
1662 L/1664 Barcode Scanner User Guide 1.3.1 GOOD READ LED *Enable Good Read LED Disable Good Read LED 1.3.2 GOOD READ LED DURATION By default, the Good Read LED stays on for 40 milliseconds. Specify a value, ranging from 1 to 254 in units of 10 milliseconds. Good Read LED Time-out after 0.01~2.54 sec. (*40 ms) 1) Read the barcode above to specify the time interval before the Good Read LED goes off. 2) Read the “Decimal Value” barcode on page 錯誤! 尚未定義書籤。.
Chapter 1 Understanding the Barcode Scanner 1.4 BEEPER The scanner has a buzzer to provide user feedback in various operating conditions.
1662 L/1664 Barcode Scanner User Guide 1.4.
Chapter 1 Understanding the Barcode Scanner 1.4.
1662 L/1664 Barcode Scanner User Guide 1.4.3 LOW BATTERY ALARM By default, the built-in battery alarm will sound when the battery charge gets low. In order to prevent data loss, it is advised to replace the battery immediately when hearing two short beeps (high tone). Disable *Enable 1.5 VIBRATOR 1.5.1 GOOD READ VIBRATOR Enable Good Read Vibrator *Disable Good Read Vibrator 1.5.2 GOOD READ VIBRATOR DURATION By default, the Good Read Vibrator stays on for 1 second.
Chapter 1 Understanding the Barcode Scanner 3) Read the “Validate” barcode on the same page to complete this setting.
1662 L/1664 Barcode Scanner User Guide 1.6 SEND “NR” TO HOST The scanner can send a “NR” string to the host to notify a No Read event.
Chapter 1 Understanding the Barcode Scanner 1.7 SCAN MODES Different scan modes are supported – select the scan mode that best suits the requirements of a specific application. Refer to the comparison table below.
1662 L/1664 Barcode Scanner User Guide 1.7.1 LASER MODE The scanner will start scanning once the trigger is held down. The scanning won't stop until (1) a barcode is decoded, (2) the pre-set timeout expires, or (3) you release the trigger. Note: Refer to “Scanning Timeout”. *Laser Mode 1.7.2 AUTO OFF MODE The scanner will start scanning once the trigger is pressed. The scanning won't stop until (1) a barcode is decoded, and (2) the pre-set timeout expires. Note: Refer to “Scanning Timeout”.
Chapter 1 Understanding the Barcode Scanner 1.7.4 AIMING MODE (1664 ONLY) The scanner will aim at a barcode once the trigger is pressed, and start scanning when the trigger is pressed again within one second. The scanning won't stop until (1) a barcode is decoded, and (2) the pre-set timeout expires. Aiming Mode Aiming Timeout You can limit the aiming time interval (1~15). By default, the scanner time-out is set to 1 second. Aiming Time-out after 1~15 sec.
1662 L/1664 Barcode Scanner User Guide 1.7.6 CONTINUOUS MODE (1662 L ONLY) The scanner is always scanning. After a successful decoding, the removal of barcode is required. It is not allowed to proceed to decode until the decoding delay time has passed. To decode the same barcode repeatedly, move away the barcode and put it back again and again for scanning. Note: Refer to “Delay between Re-read”. Continuous Mode Decoding Delay Set the time interval between each decoding. *Disable 0.
Chapter 1 Understanding the Barcode Scanner 1.8 SCANNING TIMEOUT Specify the scanning time interval (1~254 sec.; 0= Disable) when the scan mode is set to any of the following – Laser mode Auto Off mode Auto Power Off mode Aiming mode (1664 Only) Scanner Time-out after 0~254 sec. (*10) 1) Read the barcode above to specify the time interval in seconds before the scan engine times out. 2) Read the “Decimal Value” barcode on page 錯誤! 尚未定義書籤。.
1662 L/1664 Barcode Scanner User Guide 1.
Chapter 1 Understanding the Barcode Scanner 1.10 READ REDUNDANCY FOR ALL SYMBLOGIES Select the level of reading security. For example, If "No Redundancy" is selected, one successful decoding will make the reading valid and induce the "READER Event". If "Three Times" is selected, it will take a total of four consecutive successful decoding of the same barcode to make the reading valid.
1662 L/1664 Barcode Scanner User Guide 1.11 ADDON SECURITY FOR UPC/EAN BARCODES The scanner is capable of decoding a mix of UPC/EAN barcodes with and without addons. The read redundancy (0~30 times) allows changing the number of times to decode a UPC/EAN barcode before transmission. The more redundancy selected, the higher the reading security is, and thus, the slower the reading speed becomes. Note: UPC/EAN Addon 2 and Addon 5 must be enabled individually for this setting to take effect.
Chapter 1 Understanding the Barcode Scanner 1.13 USE DIRECT USB CABLE 1662 L/1664 supports Direct USB interface for charging the battery and/or sending data to the host in memory mode. Refer to 1.2.2 Memory Mode. Note: The scanner will not function when it is solely on USB power and without a battery loaded. 1.13.
1662 L/1664 Barcode Scanner User Guide 1.14 PICKLIST MODE (1664 ONLY) Picklist mode enables the decoder to decode only the barcodes aligned under the center of the laser aiming pattern. Enable *Disable 1.15 PAGER BEEP DURATION Paging function is only activated when 1662 L/1664 is in Power-Saving mode. 1662 L/1664 can be woken up via receiving any Bluetooth® status command by pressing a key on the host keyboard.
Chapter 1 Understanding the Barcode Scanner 1.16 TIME STAMP Specify time stamp format added to the prefix or suffix of a data. Up to three settings can be configured: No Time Stamp Add Time Stamp in front of data Add Time Stamp to the end of data If added in front of data, it means prior to the prefix field. Alternatively, to the end of data. No Time Stamp *Disable Add Time Stamp in front of Data Add Time Stamp to the end of Data 1.16.
1662 L/1664 Barcode Scanner User Guide Date Output *Enable Date Output Disable Hour Output *Enable Hour Output Diable Minute Output *Enable Minute Output Disalbe Second Output *Enable Second Output Diable 50 Enter Setup
Chapter 1 Understanding the Barcode Scanner Decoding Data and Time Year Setup Date Setup Time Setup 1) Read the barcode above to apply time or date code separately, and follow steps 2~3. 2) Read the “Decimal Value” barcode on page 錯 誤 ! 尚 未 定 義 書 籤 。 for the desired character string. For example: Year: Read “2”, “0”, “1”, “1” for the year setting as year=2011. Date: Read “1”, “1”, ”2”, “0” for the date setting as date=Nov.20. Time: Read “1”, “8”, “5”, “9” for the time setting as time=18:59.
1662 L/1664 Barcode Scanner User Guide 3) Read the “Validate” barcode on the same page to complete this setting. 1.16.3 DATE FORMAT The date format includes year, month and day.
Chapter 1 Understanding the Barcode Scanner 1.17 2D DECODE SETTING (1664 ONLY) 1.17.1 AIMING PATTERN Enable/Disable the aiming pattern during scanning. *Enable Disable 1.17.2 DECODING ILLUMINATION Enable/Disable illumination during scanning. Enabling illumination usually results in superior images. The effectiveness of the illumination decreases as the distance to the target increases.
1662 L/1664 Barcode Scanner User Guide 1.18 HARDWARE RESET 1.18.1 RESTORE SYSTEM DEFAULTS In addition to using the “Restore System Defaults” barcode, the following procedure using key combinations, can be used to restore the system defaults during operation. 1) Hold down the [Power/Delete] key. 2) When the scanner responds with two short beeps (high tone), press the [Trigger] key for 5 seconds. The scanner LED indicator becomes solid red and then goes off.
Chapter 1 Understanding the Barcode Scanner 55 Update
Chapter 2 SELECTING OUTPUT INTERFACE In order to establish a proper connection between host computer and the scanner, we suggest following these instructions – 1) Install battery and hold down the [Power/Delete] key for 2 seconds to turn on the scanner. 2) Read the “Enter Setup” barcode to enter the configuration mode. 3) Read the associated barcodes to activate the desired interface. See the following sections for output interfaces supported. 4) Read the barcodes for related settings.
1662 L/1664 Barcode Scanner User Guide 2.1 BLUETOOTH® HID For Bluetooth® HID, refer to Chapter 3 – Setting up a WPAN Connection for related connection settings. The scanned data will be transmitted to the computer. To capture the data run any text editor on your computer.
Chapter 2 Selecting Output Interface 2.1.1 ACTIVATE BLUETOOTH® HID & SELECT KEYBOARD TYPE When Bluetooth® HID interface is activated, you will have to select a keyboard type to complete this setting. By default, Bluetooth® HID is activated on the scanner, and the keyboard type is set to PCAT (US). Activate Bluetooth® HID & Select Keyboard Type… 1) Read the barcode above to activate Bluetooth® HID and select a keyboard type. 2) Read the “Decimal Value” barcode on page 錯誤! 尚未定義書籤。.
1662 L/1664 Barcode Scanner User Guide 2.1.2 RESET CONNECTION For Bluetooth® HID, you can only have the scanner connected to one computer at a time. If you want to connect the scanner to another host, you must read the “Reset Connection” barcode so that the current connection record will be cleared. Then, the scanner will restart itself automatically. Go through the process in 3.2.3 Connect to Dongle to establish a new connection. Refer to 1.18 Hardware Reset.
Chapter 2 Selecting Output Interface 2.1.3 KEYBOARD SETTINGS Alphabet Layout Numeric Layout Capital Lock Type Capital Lock Setting Alphabet Transmission Numeric Transmission Kanji Transmission Note: Bluetooth® HID does not support these functions on PDAs – (1) Capital Lock Setting: Auto Detection (2) Numeric Transmission: Numeric Keys Alphabet Layout By default, the alphabet layout is set to normal mode, also known as the standard English layout.
1662 L/1664 Barcode Scanner User Guide US Keyboard Style – Normal QWERTY layout, which is normally used in western countries. Select “Lower Row” for the “Numeric Layout” setting for the upper row is for special characters. French Keyboard Style – AZERTY French layout; see below for French Keyboard Style. Select “Upper Row” for the “Numeric Layout” setting for the lower row is for special characters. German Keyboard Layout – QWERTZ German layout; see below for German Keyboard Style.
Chapter 2 Selecting Output Interface Numeric Layout Select a proper layout that matches the alphabet layout. The scanner will make adjustments according to this setting. Options Description Normal Depends on the [Shift] key or [Shift Lock] setting Lower Row For QWERTY or QWERTZ keyboard Upper Row For AZERTY keyboard *Normal Upper Row Lower Row Note: This setting is to be used with the Character Substitution setting when support for certain keyboard types (languages) is unavailable but required.
1662 L/1664 Barcode Scanner User Guide Capital Lock Type & Setting In order to send the alphabet with correct case, the scanner needs to know the status of Caps Lock on the keyboard. Incorrect settings may result in reversed case of the alphabet being transmitted. Cap Lock Type Description Normal Normal type Capital Lock When enabled, the keys of alphabetic characters will be interpreted as capital letters. However, this does not affect the number or punctuation keys.
Chapter 2 Selecting Output Interface *Capital Lock OFF 65 Update
1662 L/1664 Barcode Scanner User Guide Alphabet Transmission By default, the alphabet transmission is case-sensitive, meaning that the alphabet will be transmitted according to the original case, the status of Caps Lock on the keyboard, as well as the Capital Lock setting. Select [Ignore Case] to have alphabet transmitted according to the status of Caps Lock on the keyboard only. Ignore Case *Case-sensitive Refer to 5.1 Letter Case.
Chapter 2 Selecting Output Interface Numeric Transmission By default, the alphanumeric keypad is used for transmitting digits. Select “Numeric Keypad” if you wish to use the keys on the numeric keypad. Numeric Key *Alphanumeric Key Note: If you select “Numeric Keypad”, the Num Lock status of the physical keyboard should be “ON”. This setting is not supported on PDAs.
1662 L/1664 Barcode Scanner User Guide 2.1.4 INTER-CHARACTER DELAY By default, the inter-character delay is set to zero. Specify a value, ranging from 0 to 254 in units of milliseconds, to match the computer response time of the keyboard interface. Such delay time is inserted between every character being transmitted. The longer the delay time is, the slower the transmission speed will be. Inter-Character Delay… (*0~254) 1) Read the barcode above to specify the inter-character delay.
Chapter 2 Selecting Output Interface 2.1.6 HID CHARACTER TRANSMIT MODE By default, HID interface sends data to the host in batch. You may read the “By Character” barcode to process data one character at a time. *Batch Processing By Character Note: “By Character” transmit mode is required when working with iPhone or iPad. 2.1.7 KEYPAD SUPPORT FOR IPHONE/IPAD When the scanner has been successfully connected to iPhone or iPad for data collection, the onscreen keypad of iPhone or iPad will disappear.
1662 L/1664 Barcode Scanner User Guide 2.2 BLUETOOTH® SPP SLAVE For Bluetooth® SPP Slave, refer to Chapter 3 – Setting up a WPAN Connection for related connection settings. 2.2.1 ACTIVATE BLUETOOTH® SPP SLAVE MODE This is SPP Slave Mode. Activate Bluetooth® SPP, Slave Mode 2.2.2 INTER-FUNCTION DELAY By default, the inter-function delay is set to zero. Specify a value, ranging from 0 to 254 in units of milliseconds, to match the computer response time of the keyboard interface.
Chapter 2 Selecting Output Interface 2.2.3 ACK/NAK TIMEOUT By default, the scanner sends data to the host without waiting for an ACK/NAK response before sending more data. Specify a value, ranging from 1 to 99 in units of 0.1 second. If no response within the specified period of time, the scanner will attempt to send the same data two more times. If all three attempts fail without any notification, data loss will occur.
1662 L/1664 Barcode Scanner User Guide 2.3 BLUETOOTH® SPP MASTER As a SPP master device, the scanner will be able to resume connection with the host upon powering on again, as long as the host application is running. If the scanner fails to resume connection, it will try every 5 seconds to re-connect to the host unless you read the “Reset Connection” or “Restore System Defaults” barcode. For Bluetooth® SPP Master, refer 3.2.2 Configure Related Settings for related connection settings.
Chapter 2 Selecting Output Interface Note: Read the “Set Connection” barcode first, and then the “MAC ID” barcode within 10 seconds. Instead of producing the “MAC ID” barcode, you may read the setup barcodes for entering the MAC address. Read the “Abort” barcode to cancel the operation at any time while reading setup barcodes for the MAC address. If the MAC address has not been completed yet, reading the “Validate” barcode can cancel the operation as well.
1662 L/1664 Barcode Scanner User Guide 2.3.2 INTER-FUNCTION DELAY By default, the inter-function delay is set to zero. Specify a value, ranging from 0 to 254 in units of milliseconds, to match the computer response time of the keyboard interface. Such delay time is inserted between every function code (0x01 ~ 0x1F) being transmitted. The longer the delay time is, the slower the transmission speed will be. Inter-Function Delay… (*0~254) 1) Read the barcode above to specify the inter-function delay.
Chapter 2 Selecting Output Interface 2.3.3 ACK/NAK TIMEOUT By default, the scanner sends data to the host without waiting for an ACK/NAK response before sending more data. Specify a value, ranging from 1 to 99 in units of 0.1 second. If no response within the specified period of time, the scanner will attempt to send the same data two more times. If all three attempts fail without any notification, data loss will occur.
1662 L/1664 Barcode Scanner User Guide 2.4 USB HID VIA 3610 For USB HID, connect 3610 to the USB port of PC, and then connect the scanner to 3610. The scanned data will be transmitted to the computer. To capture the data run any text editor on your computer.
Chapter 2 Selecting Output Interface 2.4.1 ACTIVATE USB HID & SELECT KEYBOARD TYPE When USB HID interface is activated, you will have to select a keyboard type to complete this setting. Activate 3610 USB HID & Select Keyboard Type… 1) Read the barcode above to activate USB HID and select a keyboard type. 2) Read the “Decimal Value” barcode on page 錯誤! 尚未定義書籤。. Refer to the table below for the number of desired keyboard type. 3) Read the “Validate” barcode on the same page to complete this setting.
1662 L/1664 Barcode Scanner User Guide 2.4.2 KEYBOARD SETTINGS Alphabet Layout Numeric Layout Capital Lock Type Capital Lock Setting Alphabet Transmission Numeric Transmission Kanji Transmission Alphabet Layout By default, the alphabet layout is set to normal mode, also known as the standard English layout. Select French or German keyboard layout if necessary. The scanner will make adjustments when sending the "A", "Q", "W", "Z", "Y", and "M" characters according to this setting.
Chapter 2 Selecting Output Interface US Keyboard Style – Normal QWERTY layout, which is normally used in western countries. Select “Lower Row” for the “Numeric Layout” setting for the upper row is for special characters. French Keyboard Style – AZERTY French layout; see below for French Keyboard Style. Select “Upper Row” for the “Numeric Layout” setting for the lower row is for special characters. German Keyboard Layout – QWERTZ German layout; see below for German Keyboard Style.
1662 L/1664 Barcode Scanner User Guide Numeric Layout Select a proper layout that matches the alphabet layout. The scanner will make adjustments according to this setting.
Chapter 2 Selecting Output Interface Capital Lock Type & Setting In order to send the alphabet with correct case, the scanner needs to know the status of Caps Lock on the keyboard. Incorrect settings may result in reversed case of the alphabet being transmitted. Cap Lock Type Description Normal Normal type Capital Lock When enabled, the keys of alphabetic characters will be interpreted as capital letters. However, this does not affect the number or punctuation keys.
1662 L/1664 Barcode Scanner User Guide *Capital Lock OFF 82 Enter Setup
Chapter 2 Selecting Output Interface Alphabet Transmission By default, the alphabet transmission is case-sensitive, meaning that the alphabet will be transmitted according to the original case, the status of Caps Lock on the keyboard, as well as the Capital Lock setting. Select [Ignore Case] to have alphabet transmitted according to the status of Caps Lock on the keyboard only. Ignore Case *Case-sensitive Refer to 5.1 Letter Case.
1662 L/1664 Barcode Scanner User Guide Numeric Transmission By default, the alphanumeric keypad is used for transmitting digits. Select “Numeric Keypad” if you wish to use the keys on the numeric keypad. Numeric Key *Alphanumeric Key Note: If you select “Numeric Keypad”, the Num Lock status of the physical keyboard should be "ON". Kanji Transmission Kanji Transmission is supported by the scanner when either Bluetooth® HID or USB HID is selected for the output interface.
Chapter 2 Selecting Output Interface 2.4.3 INTER-CHARACTER DELAY By default, the inter-character delay is set to zero. Specify a value, ranging from 0 to 254 in units of milliseconds, to match the computer response time of the keyboard interface. Such delay time is inserted between every character being transmitted. The longer the delay time is, the slower the transmission speed will be. Inter-Character Delay… (*0~254) 1) Read the barcode above to specify the inter-character delay.
1662 L/1664 Barcode Scanner User Guide 2.4.5 HID CHARACTER TRANSMIT MODE By default, HID interface sends data to the host in batch. Read the “By Character” barcode will send the data one character at a time.
Chapter 2 Selecting Output Interface 2.5 USB VIRTUAL COM VIA 3610 Connect 3610 to the USB port of PC, and then connect the scanner to 3610. You may run HyperTerminal.exe on the computer to view and capture the data transmission from the scanner. Note: If you are using USB Virtual COM for the first time, you must install its driver from the CD-ROM. Driver version 5.3 or later is required. Please remove older versions before installing new ones! 2.5.
1662 L/1664 Barcode Scanner User Guide 2.5.3 ACK/NAK TIMEOUT By default, the scanner sends data to the host without waiting for an ACK/NAK response before sending more data. Specify a value, ranging from 1 to 99 in units of 0.1 second. If no response within the specified period of time, the scanner will attempt to send the same data two more times. If all three attempts fail without any notification, data loss will occur.
Chapter 2 Selecting Output Interface 2.6 DIRECT USB HID 1662 L/1664 supports “Direct” USB HID interface for memory mode. Use the provided USB cable to connect 1662 L/1664 to the USB port of PC. Run any text editor on a computer to view and capture the scanned data being transmitted to the computer. Refer to 1.2.2 Memory Mode.
1662 L/1664 Barcode Scanner User Guide 2.6.1 ACTIVATE USB HID & SELECT KEYBOARD TYPE When USB HID interface is activated, please select a keyboard type to complete this setting. Activate Direct USB HID & Select Keyboard Type… 1) Read the barcode above to activate USB HID and select a keyboard type. 2) Read the “Decimal Value” barcode page 錯誤! 尚未定義書籤。 . Refer to the table below for the number of desired keyboard type. 3) Read the “Validate” barcode on the same page to complete this setting.
Chapter 2 Selecting Output Interface 2.6.2 KEYBOARD SETTINGS Alphabet Layout Numeric Layout Capital Lock Type Capital Lock Setting Alphabet Transmission Numeric Transmission Kanji Transmission Alphabet Layout By default, the alphabet layout is set to normal mode, also known as the standard English layout. Select French or German keyboard layout if necessary. The scanner will make adjustments when sending the "A", "Q", "W", "Z", "Y", and "M" characters according to this setting.
1662 L/1664 Barcode Scanner User Guide US Keyboard Style – Normal QWERTY layout, which is normally used in western countries. Select “Lower Row” for the “Numeric Layout” setting for the upper row is for special characters. French Keyboard Style – AZERTY French layout; see below for French Keyboard Style. Select “Upper Row” for the “Numeric Layout” setting for the lower row is for special characters. German Keyboard Layout – QWERTZ German layout; see below for German Keyboard Style.
Chapter 2 Selecting Output Interface Numeric Layout Select a proper layout that matches the alphabet layout. The scanner will make adjustments according to this setting. Options Description Normal Depends on the [Shift] key or [Shift Lock] setting Lower Row For QWERTY or QWERTZ keyboard Upper Row For AZERTY keyboard *Normal Upper Row Lower Row Note: This setting is to be used with the Character Substitution setting when support for certain keyboard types (languages) is unavailable but required.
1662 L/1664 Barcode Scanner User Guide Capital Lock Type & Setting In order to send the alphabet with correct case, the scanner needs to know the status of Caps Lock on the keyboard. Incorrect settings may result in reversed case of the alphabet being transmitted. Cap Lock Type Description Normal Normal type Capital Lock When enabled, the keys of alphabetic characters will be interpreted as capital letters. However, this does not affect the number or punctuation keys.
Chapter 2 Selecting Output Interface *Capital Lock OFF 95 Update
1662 L/1664 Barcode Scanner User Guide Alphabet Transmission By default, the alphabet transmission is case-sensitive, meaning that the alphabet will be transmitted according to the original case, the status of Caps Lock on the keyboard, as well as the Capital Lock setting. Select [Ignore Case] to have alphabet transmitted according to the status of Caps Lock on the keyboard only. Ignore Case *Case-sensitive Refer to 5.1 Letter Case.
Chapter 2 Selecting Output Interface Numeric Transmission By default, the alphanumeric keypad is used for transmitting numerics. Select “Numeric Keypad” if want to use the keys on the numeric keypad. Numeric Key *Alphanumeric Key Note: If selecting “Numeric Keypad”, the Num Lock status of the physical keyboard should be "ON". Kanji Transmission Kanji Transmission is supported by the scanner when either Bluetooth® HID or USB HID is selected for the output interface.
1662 L/1664 Barcode Scanner User Guide 2.6.3 INTER-CHARACTER DELAY By default, the inter-character delay is set to zero. Specify a value, ranging from 0 to 254 in units of milliseconds, to match the computer response time of the keyboard interface. Such delay time is inserted between every character being transmitted. The longer the delay time is, the slower the transmission speed will be. Inter-Character Delay… (*0~254) 1) Read the barcode above to specify the inter-character delay.
Chapter 2 Selecting Output Interface 2.6.5 HID CHARACTER TRANSMIT MODE By default, HID interface sends data to the host in batch, or use the scanner to read the “By Character” barcode to process data one character at a time.
1662 L/1664 Barcode Scanner User Guide 2.7 DIRECT USB VIRTUAL COM 1662 L/1664 supports “Direct” USB Virtual COM interface for memory mode. Use the provided USB cable to connect 1662 L/1664 to the USB port of PC. You may run HyperTerminal.exe on a computer to view and capture the scanned data being transmitted to the computer. Refer to 1.2.2 Memory Mode. Note: If using USB Virtual COM for the first time, install its driver from the CD-ROM. Driver version 5.3 or later is required.
Chapter 2 Selecting Output Interface 2.7.3 ACK/NAK TIMEOUT By default, the scanner sends data to the host without waiting for an ACK/NAK response before sending more data. Specify a value, ranging from 1 to 99 in units of 0.1 second. If no response within the specified period of time, the scanner will attempt to send the same data two more times. If all three attempts fail without any notification, data loss will occur.
1662 L/1664 Barcode Scanner User Guide 102 Enter Setup
Chapter 3 SET UP A WPAN CONNECTION The scanner can be configured to send data to a host computer wirelessly via the 3610 dongle, or to a notebook computer or PDA with Bluetooth® wireless technology. Upon powering up, the scanner will be ready to establish a WPAN connection. To establish a connection via 3610 after reading “Set Connection” and “Serial No.” labels … Interface Option Reference USB HID 2.4 USB HID via 3610 USB Virtual COM 2.
1662 L/1664 Barcode Scanner User Guide 3.1 CONNECTING VIA 3610 By default, the interface of 3610 is set to “USB HID”. You can have up to seven scanners connected to one computer at the same time. Note: If you are using USB Virtual COM for the first time, you must install its driver from the CD-ROM. Driver version 5.3 or later is required. Please remove older versions! 3.1.1 CONNECT TO 3610 Connect any scanner to 3610 by reading the two labels at the back of 3610.
Chapter 3 Set up a WPAN Connection 3.1.2 CHANGE INTERFACE If want to change the interface 3610, use one of the connected scanners to configure the interface-related settings and it will pass the new settings to 3610, which will then initialize and pass the settings to any other connected scanners. 1) Read the “Set Connection” and “Serial Number” labels at the back of 3610. 2) Within two minutes, connect 3610 to the USB port of PC.
1662 L/1664 Barcode Scanner User Guide 3.1.3 CONFIGURE RELATED SETTINGS Sniff Mode (Power-saving) By default, this feature is enabled, meaning the scanner will listen to the wireless network at a reduced rate.
Chapter 3 Set up a WPAN Connection 3.2 CONNECTING VIA BLUETOOTH® DONGLE 3.2.1 CHANGE INTERFACE Below is the procedure to configure the scanner before establishing a WPAN connection via Bluetooth® dongle. 1) Read the “Enter Setup” barcode to enter the configuration mode.
1662 L/1664 Barcode Scanner User Guide 3.2.2 CONFIGURE RELATED SETTINGS Sniff Mode (Power-saving) By default, this feature is enabled, meaning the scanner will listen to the wireless network at a reduced rate. *Enable Disable Note: When connecting more than two scanners to a notebook computer or PDA with Bluetooth® wireless technology, we suggest that you disable the power-saving setting for a more reliable connection.
Chapter 3 Set up a WPAN Connection Authentication When any changes are made to authentication and PIN code on the scanner side, you will have to remove the scanner from the paired device list (called unpairing) and go through the whole process to re-establish the connection. The scanner allows up to 16 characters for a PIN code and provides two options for authentication: Enable Authentication with Preset PIN Read the “Use preset PIN” barcode, and change the preset PIN if necessary.
1662 L/1664 Barcode Scanner User Guide Use random PIN No PIN required Note: When using Bluetooth® HID, some device driver may not support pre-defined PIN code for authentication. In this case, make sure you have the scanner set to “No PIN or use random PIN” before pairing. While pairing, the host PIN code will be displayed on the computer screen. Have the scanner read the setup barcode “Enter PIN Code in Decimal” or “Enter PIN Code in Hexadecimal” to input the matching PIN code. Refer to 錯誤! 找不到參照來源。.
Chapter 3 Set up a WPAN Connection 3.2.3 CONNECT TO DONGLE The procedure goes through associating devices for establishing a WPAN connection, which is pretty much the same except for the software you are using. If your computer is running Microsoft® Windows® XP (SP1 to SP3), Windows Vista® Service Pack 1 (SP1) and Windows 7, you can use the software support that Windows® includes, or you can use the driver that the device manufacturer provides.
1662 L/1664 Barcode Scanner User Guide 4) Turn on the scanner with correct WPAN settings, such as select Bluetooth® SPP or Bluetooth® HID, broadcasting enabled, authentication enabled, and PIN code specified, etc. Select the check box of [My device is set up and ready to be found] on your computer. 5) Click [Next]. 6) Wait for a few seconds for the Wizard to search available devices nearby. The scanner will appear with its “serial number” as the device name.
Chapter 3 Set up a WPAN Connection 7) Click [Next]. 8) Enter the passkey for authentication, which must be exactly the same as configured for the scanner.
1662 L/1664 Barcode Scanner User Guide 9) Click [Next]. Wait for a few seconds for Windows to exchange passkeys.
Chapter 3 Set up a WPAN Connection Note: When Bluetooth security is enabled without providing a pre-set PIN code, dynamic input of PIN code is supported. 10) Click [Finish].
1662 L/1664 Barcode Scanner User Guide 11) Now the target scanner will be listed as shown below. You can have up to seven scanners connected to one computer at the same time. Select and Remove Note: When any changes are made to authentication and PIN code on the scanner side, or you want to change to use Bluetooth® HID, it is suggested that you remove the scanner from the paired device list (called unpairing) and go through the whole process to re-establish the connection.
Chapter 3 Set up a WPAN Connection Bluetooth® SPP Connected Bluetooth® SPP Disconnected 117 Update
1662 L/1664 Barcode Scanner User Guide 118 Enter Setup
SPECIFICATIONS Optical Characteristics 1662 L 1664 Scan Engine 1D Laser 2D Imager Light Source Visible Laser Diode Visible Red LED RF Characteristics WPAN Module Bluetooth® Class 2 compliance Coverage (line-of-sight) 20 meters with 3610 Interface Supported Serial Port Profile (Bluetooth® SPP) 10 KB for transmit buffer Human Interface Device Profile (Bluetooth® HID) 3610 Direct USB HID Direct USB Virtual COM Physical Characteristics Memory 4MB flash for memory mode Switch
1662 L/1664 Barcode Scanner User Guide Electrical Characteristics Battery Rechargeable Li-ion battery — 3.7 V, 850 mAh Environmental Characteristics Temperature Humidity (Non-condensing) Operating 0 °C to 50 °C Storage -20 °C to 60 °C Operating 10% to 90% Storage 5% to 95% Resistance Electrostatic Discharge ± 15 kV air discharge, ± 8 kV contact discharge Programming Support Configuration via Setup Barcodes Use setup barcodes or host serial commands.
121 Update
