2200 Omnidirectional Presentation Scanner Setup barcodes included. Version 1.
Copyright © 2017 CIPHERLAB CO., LTD. All rights reserved The software contains proprietary information of CIPHERLAB CO., LTD.; it is provided under a license agreement containing restrictions on use and disclosure and is also protected by copyright law. Reverse engineering of the software is prohibited. Due to continued product development this information may change without notice.
IMPORTANT NOTICES FOR USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
FOR EUROPE This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: - EN 60950-1: 2006+A11:2009+A1:2010+A12:2011+A2:2013 Safety of Information Technology Equipment - EN 301 489-1 V2.1.
RELEASE NOTES Version Date Notes 1.00 Nov.
CONTENTS IMPORTANT NOTICES .......................................................................................................... - 3 For USA ....................................................................................................................................... - 3 For Europe .................................................................................................................................. - 4 Safety Precautions .............................................................
2200 Omnidirectional Presentation Scanner User Guide NUMERAL SYSTEMS ................................................................................................................ 29 Decimal System ......................................................................................................................... 29 Hexadecimal System ................................................................................................................ 30 ASCII Table ........................................
INTRODUCTION Equipped with a 2D barcode reader, the scanner is capable of reading 1D and 2D barcodes. The scanner is designed for desktop use with ease of installation. For particular deployment, the scanner can be integrated with other devices, like POS, to achieve systematic data colletion. This manual contains information on operating the scanner and using its features. It is better to keep one copy of the manual at hand for quick reference or maintenance purposes.
2200 Omnidirectional Presentation Scanner User Guide INSIDE THE PACKAGE The items included in the package may be different, depending on order. Rich choices of output interfaces are available to enhance the total performance of the scanner. Refer to product specifications. Save the box and packaging material for future use in case it is need to store or ship the scanner.
錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 SYMBOLOGIES SUPPORTED Most of the popular barcode symbologies are supported, as listed below. Each can be individually enabled or disabled. The scanner will automatically discriminate and recognize all the symbologies that are enabled. Refer to Chapter 3 錯誤! 找不到參照來源。 for details of each symbology.
2200 Omnidirectional Presentation Scanner User Guide (RSS) GS1 DataBar Truncated Disabled GS1 DataBar Limited (RSS Limited) Disabled GS1 DataBar Expanded (RSS Expanded) Disabled Composite Code Composite CC-A/B Disabled Composite CC-C Disabled 2D Symbologies PDF417 Enabled MicroPDF417 Disabled Data Matrix Enabled Maxicode Enabled QR Code Enabled MicroQR Enabled Aztec Enabled Han Xin Disabled 4 Enter Setup
QUICK START The configuration of the scanner can be done by reading the setup barcodes (setup labels) contained in this manual or via the ScanMaster software. This section describes the procedure of configuring the scanner by reading the setup barcodes and provides some examples for demonstration. Note: If RS-232 or USB Virtual COM is selected for output interface, the host can directly send serial commands to configure the scanner. For example, run HyperTerminal.
2200 Omnidirectional Presentation Scanner User Guide ENTER CONFIGURATION MODE For the scanner to enter the configuration mode, have it read the "Enter Setup" barcode located at the bottom of almost every even page of this manual. The scanner will respond with six beeps and its LED indicator will become flashing red after reading the barcode. Enter Setup For configuring scanner parameters, see “Read a Setup Barcode” below.
錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 DEFAULT SETTINGS SAVE USER SETTINGS AS DEFAULTS For the scanner to keep the customized settings as user defaults, have it read the “Save as User Defaults” barcode. This is a normal setup barcode, and the scanner will respond with two beeps (low-high tone). After reading the “Update” barcode, the current settings will be saved as user defaults.
2200 Omnidirectional Presentation Scanner User Guide READ A SETUP BARCODE CONFIGURE PARAMETERS For most of the scanner parameters, only one read is required to set them to new values. The scanner will respond with two beeps (low-high tone) when each parameter is set successfully. But for a number of special parameters, multiple reads are required to complete the setting. In this case, the scanner will respond with a short beep indicating it needs to read more setup barcodes.
錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 The example below shows how to save settings as “User Default” to restore user defaults later: Steps Action Scanner Feedback if Successful 1 Power on the scanner… The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off quickly. 2 Enter the Configuration Mode… The scanner will respond with six beeps (high-low tone repeats three times), and its LED indicator will be flashing red.
2200 Omnidirectional Presentation Scanner User Guide The example below shows how to set numeric parameters: Steps Action Scanner Feedback if Successful 1 Power on the scanner... The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off quickly. 2 Enter the Configuration Mode… The scanner will respond with six beeps (high-low tone repeats three times), and its LED indicator will become flashing red. 3 Read a Setup barcode...
錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 The example below shows how to set string parameters: Steps Action Scanner Feedback if Successful 1 Power on the scanner... The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off quickly. 2 Enter the Configuration Mode… The scanner will respond with six beeps (high-low tone repeats three times), and its LED indicator will become flashing red. 3 Read a Setup barcode...
2200 Omnidirectional Presentation Scanner User Guide LIST THE CURRENT SETTINGS The current settings of all scanner parameters can be sent to the host computer for user inspection. The listing includes pages as shown below. Select the page of interest by having the scanner read the “List Page x” barcode. The scanner will respond with two beeps (low-high tone) and send the selected page to the host immediately.
錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Lists settings regarding Editing Format 1 (1/2) List Page 11 Lists settings regarding Editing Format 1 (2/2) List Page 12 Lists settings regarding Editing Format 2 (1/2) List Page 13 Lists settings regarding Editing Format 2 (2/2) List Page 14 Lists settings regarding Editing Format 3 (1/2) List Page 15 Lists settings regarding Editing Format 3 (2/2) List Page 16 Lists settings regarding Editing Format 4 (1/2) List Page 17 Lists settings regarding Ed
00 Omnidirectional Presentation Scanner User Guide CREATE ONE-SCAN SETUP BARCODES Most of the scanner parameters require only one read for setting new values. To facilitate configuring the scanner, create One-Scan setup barcodes for use.
錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 2D ONE-SCAN BARCODE Users can also scan a single 2D barcode combining with a series of serial commands to configure the scanner.
2200 Omnidirectional Presentation Scanner User Guide 16 Enter Setup
SPECIFICATIONS Optical Characteristics 2200 Scan Engine 2D Imager Light Source Aiming pattern: 520~532nm LED Illumination: 616~625nm LED Physical Characteristics Indication Tri-color LED (Red/Green/Blue) and beeper Interface Options Keyboard Wedge, RS-232, USB HID, USB Virtual COM Weight Approx.
2200 Omnidirectional Presentation Scanner User Guide Resistance Splash / Dust Resistance IP 52 Electrostatic Discharge ± 15 kV air discharge, ± 8 kV contact discharge Programming Support Configuration via Setup Barcodes Use setup barcodes or host serial commands. Software Windows®-based ScanMaster Firmware upgradeable Download firmware updates via the download utility.
Appendix I FIRMWARE UPGRADE USING RS-232 1) Connect the RS-232 cable between the scanner and the computer, and join the power supply cord. 2) Read the following barcodes in sequence to configure the scanner to use RS-232 as download interface. Enter Setup Activate RS-232 115200 bps Update 3) Read the following barcodes in sequence for the scanner to enter the download mode. The scanner will respond with beeps to indicate it is ready for downloading.
2200 Omnidirectional Presentation Scanner User Guide 4) Run the download utility “ProgLoad.exe” on the computer. Kernel Program User Program K250x_V*.shx STD250x_V*.shx For the communication settings, select “RS-232” and the correct COM port for RS-232 or USB Virtual COM interface. For RS-232, select 115200 bps for baud rate; for USB Virtual COM, ignore the baud rate setting. For the file option, click [Browse] to select the target file for firmware update. Click [OK].
Appendix I 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 USING USB VIRTUAL COM 1) Connect the USB cable between the scanner and the computer. If using USB Virtual COM for the first time, you must install its driver beforehand. 2) For Windows platform, read the following barcodes in sequence to configure the scanner to use USB VCOM_CDC as download interface.
2200 Omnidirectional Presentation Scanner User Guide Kernel Program User Program K250x_V*.shx STD250x_V*.shx For the communication settings, select “RS-232” and the correct COM port for RS-232 or USB Virtual COM interface. For RS-232, select 115200 bps for baud rate; for USB Virtual COM, ignore the baud rate setting. For the file option, click [Browse] to select the target file for firmware update. Click [OK]. 5) After upgrading kernel, you will need to restart the scanner manually.
Appendix II HOST SERIAL COMMANDS SERIAL COMMANDS D Purpose To disable the scanner. Remarks “D” E Purpose To enable the scanner. Remarks “E” #@ nnnnnn Purpose To configure the scanner. Remarks nnnnnn – the six digits of command parameters. For example, “109952” is to list the current Code ID settings.
2200 Omnidirectional Presentation Scanner User Guide #@TRIGOFF Purpose Disable software trigger Remarks “0x23” + “0x40” + “0x54” + “0x52” + “0x49” + “0x47” + “0x4f” + “0x46” + “0x46” + “0x0d” #@TRIGON Purpose Enable software trigger Remarks “0x23” + “0x40” + “0x54” + “0x52” + “0x49” + “0x47” + “0x4f” + “0x4e” + “0x0d” EXAMPLE Run HyperTerminal.exe on the host computer to send serial commands to the scanner via RS-232 or USB Virtual COM.
Appendix III KEYBOARD WEDGE TABLE “Apply” Special Keyboard 0 0 1 2 3 4 5 6 7 8 F2 SP 0 @ P ` p 1 INS F3 ! 1 A Q a q 2 DLT F4 " 2 B R b r 3 Home F5 # 3 C S c s 4 End F6 $ 4 D T d t 5 Up F7 % 5 E U e u 6 Down F8 & 6 F V f v 7 Left F9 ' 7 G W g w 8 BS F10 ( 8 H X h x 9 HT F11 ) 9 I Y i y A LF F12 * : J Z j z B Right ESC + ; K [ k { C PgUp Exec , < L \ l | D
2200 Omnidirectional Presentation Scanner User Guide “Bypass” Special Keyboard 0 1 2 3 4 5 6 7 0 SP 0 @ P ` p 1 ! 1 A Q a q 2 " 2 B R b r 3 # 3 C S c s 4 $ 4 D T d t 5 % 5 E U e u 6 & 6 F V f v 7 ' 7 G W g w 8 BS ( 8 H X h x 9 HT ) 9 I Y i y A LF * : J Z j z + ; K [ k { , < L \ l | - = M ] m } E . > N ^ n ~ F / ? O _ o Dly B ESC C D CR Note: (1) ~: Digits of numeric keypad.
Appendix III 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 KEY TYPE & STATUS KEY TYPE If “Keyboard Wedge” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable. *Normal Scan Code KEY STATUS Decide whether or not to change key status when “Normal Key” is selected for Key Type.
2200 Omnidirectional Presentation Scanner User Guide EXAMPLE KEY TYPE = NORMAL For example, if you want to program the character “!” as the prefix code: 1. Read the “Configure Prefix” barcode. 2. Read the “Hexadecimal Value” barcode on page 30 for “2” and “1”. 3. Read the “Validate” barcode to complete this setting. KEY TYPE = SCAN CODE For example, if you want to program the character “a” (= “1C” on the scan code table) as the prefix code: 1. Read the “Configure Prefix” barcode. 2.
Appendix IV NUMERAL SYSTEMS DECIMAL SYSTEM Decimal 0 1 2 3 4 5 6 7 8 9 Validate the Values Validate Update Abort 29
2200 Omnidirectional Presentation Scanner User Guide HEXADECIMAL SYSTEM Hexadecimal 0 1 2 3 4 5 6 7 8 9 A B C D E F 30 Enter Setup
Appendix IV 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Validate the Values Validate ASCII TABLE 0 0 1 2 3 4 5 6 7 DLE SP 0 @ P ` p 1 SOH DC1 ! 1 A Q a q 2 STX DC2 " 2 B R b r 3 ETX DC3 # 3 C S c s 4 EOT DC4 $ 4 D T d t 5 ENQ NAK % 5 E U e u 6 ACK SYN & 6 F V f v 7 BEL ETB ' 7 G W g w 8 BS CAN ( 8 H X h x 9 HT EM ) 9 I Y i y A LF SUB * : J Z j z B VT ESC + ; K [ k { C FF FS , < L \ l
2200 Omnidirectional Presentation Scanner User Guide 32 Enter Setup
Appendix V READING DRIVER LICENSES The scanner is capable of reading 2D driver’s licenses and other American Association of Motor Vehicle Administrators (AAMVA) compliant ID cards. For compliant 2D licensed card scanning, it decodes the information embedded in the ID cards to a formatted data. This appendix provides the setup barcodes required while ScanMaster utility provides GUI setup that is oganized and easy-to-use.
2200 Omnidirectional Presentation Scanner User Guide OUTPUT SEQUENCE SETUP The scanner supports arranging the sequences of license embedded data via separators and fields. In order to present data in a consistent format, some barcodes (ex. First Name, Middle Name/Initial, Last Name, Name suffix, Name Prefix, Birth Date and so on) will return data based on the calculated actual data contained in the ID barcode.
Appendix V 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Mailing Address Postal Code Home Address Line1 Home Address Line2 Home Address City Home Address State Home Address Postal Code License ID Number License Class License Restrictions License Endorsements Height (Feet and/or Inches) Height (Centimeters) Update Abort 35
2200 Omnidirectional Presentation Scanner User Guide Weight (Pounds) Weight (Kilograms) Eye Color Hair Color License Expiration Date Birth Date Gender License Issue Date Issue Timestamp Number of Duplicates Medical Codes Organ Donor 36 Enter Setup
Appendix V 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Nonresident Customer ID Social Security Number AKA Birth Date AKA Social Security Name AKA Full Name AKA Last Name AKA First Name AKA Middle Name/Initial AKA Name Suffix AKA Name Prefix Weight Range Update Abort 37
2200 Omnidirectional Presentation Scanner User Guide Document Discriminator Country Federal Commission Codes Place of Birth Audit Information Inventory Control Race/Ethnicity Std Vehicle Class Std Restrictions Std Endorsements Class Description Endorsement Description 38 Enter Setup
Appendix V 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Restrictions Description Permit Class Permit Expiration Date Permit ID Number Permit Issue Date Permit Restrictions Permit endorsements Issuer ID Number Family Name Truncation First Name Truncation Middle Name Truncation Update Abort 39
2200 Omnidirectional Presentation Scanner User Guide SEPARATORS AND FIELDS Define the separators that separate fields during the transmission sequence of data scanning. In addition to the built-in data elements, you can also specify up to 5 Additional Fields with 4 bytes characters. Program the transmission sequence by reading the desired fields as additional fields. Note: Up to 5 separators can be assigned.
Appendix V 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 EDIT SEPARATORS All the driver license fields can be split with a pre-selected separator, for example, “-” as First Name-Last Name or “:” as First Name:Last Name. Edit Separator 1 Edit Separator 2 Edit Separator 3 Edit Separator 4 Edit Separator 5 1) Read the barcode above to apply separator to driver license information separately, and follow steps 2~3. 2) Read the “Hexadecimal Value” barcode for the desired character string.
2200 Omnidirectional Presentation Scanner User Guide EDIT FIELDS Up to five additional fields can be created for each editing format; each of them is numbered from Additional 1 to Additional 5 accordingly. If “Bluetooth® HID” or “USB HID” is configured for interface, Key Type and Key Status will then become applicable. You may decide whether or not to apply Key Status when “Normal Key” is selected for Key Type. Key Type Key Status Scan Code Up to 2 scan code values are allowed.
Appendix VI 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 Appendix VI KEYBOARD TYPE ONE-SCAN BARCODE KEYBOARD WEDGE PCAT (US) PCAT (French) PCAT (German) PCAT (Italian) PCAT (Swedish) PCAT (Norwegian) PCAT (UK) PCAT (Belgium) Update Abort 43
2200 Omnidirectional Presentation Scanner User Guide PCAT (Spanish) PCAT (Portuguese) PS55 A01-1 PS55 A01-2 (Japanese) PS55 A01-3 PS55 001-1 PS55 001-81 PS55 001-2 PS55 001-82 44 Enter Setup
Appendix VI 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 PS55 001-3 PS55 001-8A PS55 002-1, 003-1 PS55 002-81, 003-81 PS55 002-2, 003-2 PS55 002-82, 003-82 PS55 002-3, 003-3 PS55 002-8A, 003-8A IBM 3477 Type 4 (Japanese) Update Abort 45
2200 Omnidirectional Presentation Scanner User Guide PS2-30 IBM 34XX/319X, Memorex Telex 122 Keys User-defined table PCAT (Turkish) PCAT (Hungarian) PCAT (Swiss German) PCAT (Danish) PCAT (Russian) PCAT (Cyrillic on Russian) 46 Enter Setup
Appendix VI 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 PCAT (Armenian) PCAT (Thai) Update Abort 47
2200 Omnidirectional Presentation Scanner User Guide DIRECT USB HID PCAT (US) PCAT (French) PCAT (German) PCAT (Italian) PCAT (Swedish) PCAT (Norwegian) PCAT (UK) PCAT (Belgium) PCAT (Spanish) 48 Enter Setup
Appendix VI 錯誤! 使用 [常用] 索引標籤將 Heading 1 套用到您想要在此處顯示的文字。 PCAT (Portuguese) PS55 A01-2 (Japanese) User-defined table PCAT (Turkish) PCAT (Hungarian) PCAT (Swiss German) PCAT (Danish) PCAT (Russian) PCAT (Cyrillic on Russian) Update Abort 49
2200 Omnidirectional Presentation Scanner User Guide PCAT (Armenian) PCAT (Thai) 50 Enter Setup
