8600 Series Mobile Computer 8600/8630/8660 Version 1.
Copyright © 2013 CIPHERLAB CO., LTD. All rights reserved The software contains proprietary information of CIPHERLAB CO., LTD.; it is provided under a license agreement containing restrictions on use and disclosure and is also protected by copyright law. Reverse engineering of the software is prohibited. Due to continued product development this information may change without notice.
FOR USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
FOR EUROPE– EU DECLARATION OF CONFORMITY This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: EN 60950-1: 2006+A11:2009+A1:2010+A12:2011 Safety of Information Technology Equipment EN 301 489-1 V1.8.
This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies. In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services.
FOR PRODUCT WITH LASER CAUTION This laser component emits FDA / IEC Class 2 laser light at the exit port. Do not stare into beam. SAFETY PRECAUTIONS RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. The use of any batteries or charging devices, which are not originally sold or manufactured by CipherLab, will void your warranty and may cause damage to human body or the product itself.
1.00 Oct.
CONTENTS IMPORTANT NOTICES ........................................................................................................................... - 2 For USA ................................................................................................................................................. - 3 For Canada ........................................................................................................................................... - 3 For Hand-held Product with RF Functions ....
8600 Series Mobile Computer Reference Manual 1.6.1 Barcode Scanner .................................................................................................................. 21 1.6.2 RFID Reader .......................................................................................................................... 22 1.7 Charging & Communications ...................................................................................................... 24 1.7.1 Interface Cable Options .................
8600 Series Mobile Computer Reference Manual 3.6 Load Program ................................................................................................................................ 51 3.7 DoFTP Menu ................................................................................................................................... 54 3.7.1 Local ....................................................................................................................................... 55 3.7.2 Manual ...
8600 Series Mobile Computer Reference Manual LED indicators seem not working ...................................................................................................... 97 LCD seems not working ...................................................................................................................... 97 Keypad seems not working ................................................................................................................ 98 Vibrator seems not working .................
INTRODUCTION Answering industrial demands for rugged, light-weight and versatile computers, the 8600 Series Mobile Computer is specifically designed for enterprise logistics use. Equipped with CCD (linear imager), Laser, 2D imager, or RFID scanning modules, users can choose the appropriate option that best suits to their field applications. With Bluetooth v4.
8600 Series Mobile Computer Reference Manual TERMINAL MODELS The wireless capabilities of 8600 Mobile Computer Series may vary depending on the specifications implemented. Please refer to the table below. Model WLAN (802.11 b/g/n) WPAN (Bluetooth 4.0) 8600 - - 8630 √ √ 8660 √ INSIDE THE PACKAGE The following items are included in the package. Save the box and packaging material for future use in case you need to store or ship the mobile computer.
Introduction ACCESSORIES Rich choices of optional accessories are available for you to enhance the total performance of the mobile computer.
8600 Series Mobile Computer Reference Manual GETTING STARTED COMPONENT NAMES Figure 1: Overview 4
Introduction INSERTING BATTERY & MEMORY CARD For shipping and storage purposes, save the mobile computer and the main battery in separate packages. This will keep both batteries in good condition for future use. Note: Any improper handling may reduce the battery life. 1) Hold the mobile computer still and slide the release latch to the right to unlock the battery cover. 2) Slightly hold the sides of the battery cover and take it upward off the device.
8600 Series Mobile Computer Reference Manual Note: For a new battery, make sure it is fully charged before use. Always prepare a spare battery pack, especially when you are on the road.
Introduction Figure 2: Installing the Memory Card & Main Battery 7
8600 Series Mobile Computer Reference Manual INSTALLING PISTOL GRIP This contoured pistol grip enables intuitive trigger-and-scan operation, which is very helpful in scan intensive applications. When a pistol grip is necessary, install it to the mobile computer by following these steps: 1) Place the terminal computer into the holder of the pistol grip. 2) Slide the release latch of the pistol against the terminal computer to lock it firmly, and then turn on the mobile computer to test the trigger.
Introduction INITIAL CHARGING The main and backup batteries may not be charged to full for shipment. When you first receive the package, you will need to charge the batteries to full before use. Please refer to 1.7 Charging & Communications. For the first time charge, it takes approximately 2.5 hours to charge the main battery to full. As for the backup battery charging, it takes approximately at least 72 hours whether the mobile computer is in use or not.
Chapter 1 USING THE MOBILE COMPUTER This chapter explains the features and usage of the 8600 Series Mobile Computer. IN THIS CHAPTER 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 Battery ..................................................................... Memory .................................................................... Keypad..................................................................... LCD ......................................................................... Notifications .......................
8600 Series Mobile Computer Reference Manual 1.1 BATTERY 1.1.1 MAIN BATTERY The mobile computer is powered by a rechargeable 3.7V 1100/2200 mAh Li-ion battery pack that may not be charged to full for shipment. When you first receive the package, you will need to charge the battery to full before use. The table below lists the approximate time to fully charge the included 1100/2200mAh batteries with different charging tools.
Chapter 1 Using The Mobile Computer 1.1.2 BACKUP BATTERY The backup battery, a 3.0V/18mAh rechargeable Lithium button cell on the main board, takes charge of the retention of data in SRAM, real-time clock, and calendar when the main battery is removed or drained. When fully charged, the backup battery can work for at least 25 days without the main battery. In the meantime, you have to replace the main battery as soon as possible.
8600 Series Mobile Computer Reference Manual 1.2 MEMORY The collected data can be sent back to a host computer immediately over wireless networks, or stored in memory (SRAM) and uploaded later. The mobile computer is equipped with a calendar chip for accurate time/date logging.
Chapter 1 Using The Mobile Computer 1.3 KEYPAD The mobile computer is equipped with a keypad of 29/39 keys for system setup, user entry and so on. The keypad comes with programmable LED backlight for illumination that makes the key characters easier to read when ambient light gets weaker. Refer to 1.4 LCD for screen & backlight settings. The key click can be configured through programming or via System Menu. Refer to 3.2.6 Key Click. 1.3.
8600 Series Mobile Computer Reference Manual This alphanumeric keypad is set to numeral mode by default. Press the blue key at the bottom-right to toggle between upper-case alphabet, lower-case alphabet, and numeral modes. Press the orange key at the bottom-left to toggle between function and numeral modes. The associated icon will appear on the top-left of the screen in a sequence as shown below.
Chapter 1 Using The Mobile Computer Below briefly describes the functions of common keys on the mobile computer. SCAN The yellow key located at the top center is used to trigger the scan engine so that it can read the barcode. Navigation Pad The 4-way navigation pad around the SCAN key is used to move the cursor left, up, down, or right. ENTER This key on the right side of the SCAN key is used for command execution or input confirmation.
8600 Series Mobile Computer Reference Manual 1.4 LCD The mobile computer comes with a TFT graphic LCD, 240 by 320 pixels resolution, which can be programmed to display text or graphics, such as specific font and company logo, to meet varying application needs.
Chapter 1 Using The Mobile Computer 1.5 NOTIFICATIONS 1.5.1 STATUS LED There are two dual-color LED indicators located at the upper-right of the screen. Both can be programmed to provide information that helps diagnosing. For example, if you are using AG runtime, you will be informed of the scanning result immediately. By default, LED1 is defined to light solid green for a single "Good Read" action upon reading a barcode successfully.
8600 Series Mobile Computer Reference Manual LED1: Red/Green Red Green User Power ON User definable User definable Power Off, Battery System default Charging Flashing red: Charging Charging Error Solid green for Good Read by default System default Flashing green: Charging done System default Flashing red and green: Charging error occurs LED2: Blue/Green Blue Green Bluetooth System default --- Wi-Fi Flashing blue, quickly: Waiting for connection or connecting Flashing blu
Chapter 1 Using The Mobile Computer 1.6 DATA CAPTURE 1.6.1 BARCODE SCANNER A wide variety of scan engines is available for delivering flexibility to meet different requirements. Depending on the scan engine integrated, the mobile computer is capable of scanning barcodes of a number of symbologies that are enabled by default while running the preloaded AG runtime. Refer to 3.3.1 Reader for functional test.
8600 Series Mobile Computer Reference Manual Interleaved 25 Enabled Enabled Matrix 25 Disabled Disabled Chinese 25 Code 3 of 9 Disabled Coop 25 Disabled Code 39 Enabled Trioptic Code 39 Enabled Disabled Italian Pharmacode (Code 32) Disabled French Pharmacode Disabled EAN-8 Enabled Enabled EAN-8 Addon 2 Disabled Disabled EAN-8 Addon 5 Disabled Disabled EAN-13 Enabled Enabled EAN-13 & UPC-A Addon 2 Disabled Disabled EAN-13 & UPC-A Addon 5 Disabled Disabled Bookland EAN (I
Chapter 1 Using The Mobile Computer HF Tag Protocol ISO 14443A Mifare Standard 1K (Mifare S50) UID Only Read Page Write Page SLE66CLX320P --- --- SLE55R04/08 --- --- Smart MX --- --- --- --- ISO 14443A compliant --- --- ISO 14443B compliant --- --- --- --- Mifare Standard 4K (Mifare S70) Jcop 41 (only Mifare 1K & 4K compatible) Mifare Ultralight Mifare Ultralight C Mifare ProX Mifare DESFire Mifare Plus Mifare Mini (Mifare S20) Jewel Topaz ISO 14443B SLE6666CL160S SR176 SR512 SR
8600 Series Mobile Computer Reference Manual 1.7 CHARGING & COMMUNICATIONS Normally, the mobile computer ships with a USB or RS-232 cable for charging and communications. A variety of cradles are available to meet different requirements. If you are using USB Virtual COM for the first time, you must install its driver from the CD-ROM. Driver version 5.3 or later is required. Please remove older versions! The virtual COM port will not be assigned until the USB port is in use.
Chapter 1 Using The Mobile Computer RS-232 Interface Cable Task RS-232 Cable Charging 5 V charging from the adaptor (Plug icon) Communications If using FORGE Application Generator software, you may use a download utility to receive data on your computer; otherwise, run HyperTerminal.exe to receive data directly.
8600 Series Mobile Computer Reference Manual 1.7.1 INTERFACE CABLE OPTIONS For charging via the USB cable, the standard charging current is 500 mA. However, we recommend that you connect the power adaptor to speed up charging the battery. If you connect the mobile computer to a USB hub, the charging current may be insufficient. In that case, change the charging current to 100 mA after connecting the USB cable. It will take a longer time to charge to full. Refer to 3.2.9 USB Charge Current.
Chapter 1 Using The Mobile Computer 1.7.2 CRADLE OPTIONS A variety of cradles are developed for the mobile computer and ship on your option. These cradles employ different data connections, but they all support charging the mobile computer while transmitting data at the same time. Choose a cradle type that best suits your needs.
8600 Series Mobile Computer Reference Manual Figure 7: Setting up cradle Charging & Communication Cradle 28
Chapter 1 Using The Mobile Computer No. Description No. Description 1 Status LED (POWER) 2 Cable Connector (USB or RS-232) 3 Power Jack Battery Charger No. Description No.
8600 Series Mobile Computer Reference Manual 1.8 SD CARD SD card can be accessed directly by using the provided functions in user applications. Yet, when the mobile computer is equipped with an SD card and connected to the host computer via the USB cable, it can be treated as a removable disk (USB mass storage device) as long as it is configured properly through programming or via System Menu | 8. Next Page | 1. Storage Menu | 1. Run As USB Disk. Refer to 3.8 Storage Menu.
Chapter 1 Using The Mobile Computer DAT Filename DAT file #1 TXACT1.DAT DAT file #2 TXACT2.DAT DAT file #3 TXACT3.DAT DAT file #4 TXACT4.DAT DAT file #5 TXACT5.DAT DAT file #6 TXACT6.DAT DBF Filename DBF file #1 DBF file #2 DBF file #3 DBF file #4 DBF file #5 Record file F1.DB0 System Default Index F1.DB1 Index file #1 F1.DB2 Index file #2 F1.DB3 Index file #3 F1.DB4 Record file F2.DB0 System Default Index F2.DB1 Index file #1 F2.DB2 Index file #2 F2.
8600 Series Mobile Computer Reference Manual \AG\DBF \AG\DAT Application Generator (a.k.a. AG) Store DAT, DBF, and Lookup files that are created and/or accessed in Application Generator to this folder. \AG\EXPORT \AG\IMPORT 1.8.3 FILE NAME A file name must follow 8.3 format (= short filenames) — at most 8 characters for filename, and at most three characters for filename extension.
Chapter 2 LEARNING SOFTWARE ARCHITECTURE This chapter mainly describes the software inside the mobile computer. It consists of three modules — Kernel, System, and Application; each has a function menu. When a menu is displayed, you may select an item by either of the following ways: Press the arrow keys [Up] and [Down] to move the highlight bar. Press the number key that corresponds to the item number.
8600 Series Mobile Computer Reference Manual Figure 8: Software Architecture IN THIS CHAPTER 2.1 Application Module ..................................................... 35 2.2 System Configuration & Core .......................................
Chapter 2 Learning Software Architecture 2.1 APPLICATION MODULE The mobile computer ships with software package on the CD-ROM including FORGE Application Generator (Batch and WLAN versions), MIRROR Emulator (VT and 5250 versions), and download utilities. 2.1.1 FORGE APPLICATION GENERATOR (AG) FORGE Application Generator (AG) software package includes: Forge.exe/AG8600WLAN.
8600 Series Mobile Computer Reference Manual 2.1.2 MIRROR EMULATOR (CIPHERNET) The mobile computer supports VT100/220 and IBM 5250 terminal emulation for accessing a backend database. Instead of using FORGE Application Generator, you may download the terminal emulation program, i.e. CipherNet Runtime, to the mobile computer. Refer to 3.6 Load Program. Then, run individual companion tool on your computer. For details on the MIRROR Emulator application, please refer to separate user manuals.
Chapter 2 Learning Software Architecture 2.2 SYSTEM CONFIGURATION & CORE For managing system configurations and multiple programs, each mobile computer comes with System Menu, Program Manager, and Kernel Menu. Refer to the following chapters on how to configure the 8600 Series Mobile Computer, regarding system configurations and program download. 2.2.1 SYSTEM MENU System Menu is bundled with BASIC Runtime or user programs that are written in C language.
8600 Series Mobile Computer Reference Manual 38
Chapter 3 SYSTEM MENU System Menu offers an interface for engineers (programmers or system integrator) to view system information, change the configuration parameters, download programs and run diagnostics. This menu is designed for engineering tests and maintenance ONLY. For this reason, it provides password protection to prevent unauthorized users from accidentally changing system settings. Warning! System Menu is NOT for the use of any end users.
8600 Series Mobile Computer Reference Manual IN THIS CHAPTER 3.1 Information............................................................... 3.2 Settings ................................................................... 3.3 Tests ....................................................................... 3.4 Memory .................................................................... 3.5 Power ...................................................................... 3.6 Load Program...............................
Chapter 3 System Menu 3.1.1 UNDERSTANDING DEVICE CODE Device Code Modular Component Types 1st digit 0= none Reader module 1= CCD scan engine 2= Laser scan engine 3= 2D scan engine 2nd digit Wireless module 0= none 5= Bluetooth only 8= Bluetooth + 802.
8600 Series Mobile Computer Reference Manual 3.2 SETTINGS You can change the default settings here. System Settings Default Values Clock Current time Backlight 20 seconds at level 2, backlight shade enabled Contrast Level 4 Auto Off 10 minutes Power On Options Program Resume Key Click Tone 2 Speaker Volume High volume level USB VCOM No.
Chapter 3 System Menu 3.2.3 CONTRAST Set the contrast level for the LCD. Press the arrow keys [Up] and [Down] to adjust the contrast level. 3.2.4 AUTO OFF The mobile computer will be turned off automatically when no operation is taking place during a specified period of time. Enter a value between 0 and 999 (minute). Note: To disable this function, enter 0. 3.2.
8600 Series Mobile Computer Reference Manual 3.2.6 KEY CLICK The system will produce an audible signal when any key on the keypad is pressed. The current value is highlighted. Select a desired tone for the speaker or mute it. 3.2.7 SPEAKER VOLUME Set the speaker volume. Press the arrow keys [Up] and [Down] to adjust the volume level (3 levels) or mute it. 3.2.
Chapter 3 System Menu 3.2.11 SYSTEM PASSWORD Set a password to control user access to System Menu, Program Manager and Kernel Menu. The password can be up to eight alphanumeric characters. Note: The password is case-sensitive. To disable a previous password, enter blank on the "Input new password" and "Verify password" screens. 3.2.12 DEFAULT SET Reset system settings to the default values, except for the reader settings. 3.2.13 RESET READER Reset reader settings to the default values.
8600 Series Mobile Computer Reference Manual 3.3 TESTS Here provides functional tests for key parts. 3.3.1 READER Test the reading performance of the scanner. The supported symbologies depend on the scan engine you use. Refer to 1.6 Data Capture for symbologies that are enabled by default. For symbologies that are disabled by default, they must be enabled through programming. Press [SCAN] to start. To stop and exit the test, press any key. 3.3.2 SPEAKER Test the speaker with different volume levels.
Chapter 3 System Menu Warning! The contents of the data memory (SRAM) will be wiped out after test. 3.3.6 ECHO TEST After a physical connection is established properly, run a test utility on your computer and start the test on your mobile computer. Select a desired baud rate if necessary. To stop and exit the test, press [ESC]. Interface Description RS-232 This echo test is to verify connectivity via the RS-232 cable EchoTest.exe between the mobile computer and a host computer.
8600 Series Mobile Computer Reference Manual Satellite Number Displays how many GPS satellites are in view. SNR Signal/Noise Ratio measured in dB.
Chapter 3 System Menu 3.4 MEMORY Here provides information and initialization function of the memory. 3.4.1 SIZE INFORMATION RAM Flash — onboard SRAM for data memory — program memory 3.4.2 INITIALIZE Initialize the data memory. Warning! The contents of the data memory (SRAM) will be wiped out after memory initialization.
8600 Series Mobile Computer Reference Manual 3.5 POWER Here shows current voltage consumption. Main (battery) It shows dynamic status of the battery pack, which is used as the main power source. Backup (battery) It shows dynamic status of the button cell, which is used to retain data in SRAM. Warning! 50 Always examine the battery icon on the device screen so that you will be alerted for a low battery condition.
Chapter 3 System Menu 3.6 LOAD PROGRAM Here you can access the Load Program service provided by the kernel. Because the kernel will take over the job, you will not be able to return to System Menu by pressing [ESC]. After downloading, restart the mobile computer to activate the new program. Refer to Appendix I Download Utility. Note: The mobile computer will stay in download mode for approximately 30 seconds. .
8600 Series Mobile Computer Reference Manual SETTINGS Interface Options Description RS-232 Proceed to configure baud rate settings on your computer and the mobile computer. USB VCOM Connect the USB cable between your computer and the mobile computer. Bluetooth Approach the target Bluetooth enabled device. SD Card This option is available only when the memory card is present. USB VCOM_CDC Connect the USB cable between your computer and the mobile computer.
Chapter 3 System Menu LOAD PROGRAM VIA SD CARD Press the arrow keys to select a file. Then, press [ENTER] to view information of the program file. 1) If you have copied the desired program file(s) to your SD card, go to System Menu | 6. Load Program and select SD Card. You will see a list of all the files under the directory “\Program”, as shown above. 2) Press the arrow keys [Up] and [Down] to select a file. 3) Press [ENTER] to view information of the program file.
8600 Series Mobile Computer Reference Manual 3.7 DOFTP MENU This submenu is for the FTP client connection. It will log the mobile computer into an FTP server via Wi-Fi or Ethernet Cradle for the following tasks. Execute and/or update the script file “FTP.dat” Download the program update(s) Note: Go to System Menu and configure the network settings first. Refer to 3.10 Wi-Fi Menu. .
Chapter 3 System Menu 3.7.1 LOCAL Depending on the script file “FTP.dat” saved on the mobile computer, you may update the script file or download any program update from FTP server, if necessary. SETTING Interface Options Supported Description Ethernet Cradle Seat the mobile computer in the Ethernet Cradle. Wi-Fi Connect the mobile computer to an access point. Note: This setting is available only when the Wi-Fi module is present. 3.7.
8600 Series Mobile Computer Reference Manual 3.8 STORAGE MENU This submenu is for using the mobile computer equipped with SD card as a removable disk, as well as for directly accessing files on SD card. Note: When SD card is present, the card icon will appear flashing while being accessed. If the mobile computer is preloaded with Batch AG runtime, it will automatically create two working directories “\AG\IMPORT” and “\AG\EXPORT” on SD card. 3.8.
Chapter 3 System Menu Check Memory For an SD card that has never been used on 8600, a message like “Found New SD Card” will be displayed allowing users to scan the card for memory check. If the action is canceled then, memory check can still be performed here. Check File Size You may calibrate the size of DAT files on SD card while running BASIC application, and it will refresh the size of “A:\BASICRUN\TXACTn.DAT” (n=1~6).
8600 Series Mobile Computer Reference Manual 3.9 BLUETOOTH MENU This submenu is for the mobile computer, with built-in Bluetooth module, to work with other Bluetooth enabled devices. You must configure these parameters correctly. Bluetooth Settings Default Value Connect Setting HID, SPP, FTP Client DUN Items Need to Be Checked Local Name Model no. + Serial no.
Chapter 3 System Menu 3.9.1 INFORMATION Information of network configuration can be viewed here. Bluetooth Menu | 1. Information LIB Kernel version All user libraries reside in Kernel; no external libraries are required. MAC MAC address of the Bluetooth module IAM A name given to the mobile computer for identification CTY "Normal" means all 79 channels are available for frequency-hopping DHCP There are bandwidth limitations for 2.4 GHz ISM band in some countries.
8600 Series Mobile Computer Reference Manual 3.9.2 CONNECT SETTING Set the connection parameters if necessary. Local Name Enter a name for identifying the mobile computer. By default, it is made up of model number and the serial number. Remote Name Leave it empty unless you want to make a specific connection. Broadcast Me Options — Enable or Disable For initial connection, broadcasting must be enabled so that other Bluetooth devices can discover the mobile computer.
Chapter 3 System Menu 3.9.3 SECURITY Set or modify security parameters. Authentication Options — Enable or Disable PIN Code Define the encryption key values. Up to 16 characters, using ASCII code. Note: When authentication is enabled without providing a pre-set PIN code, the mobile computer supports dynamic input of PIN code during pairing.
8600 Series Mobile Computer Reference Manual 3.9.4 ECHO TESTS These echo tests are used for verifying connectivity to make sure the mobile computer is within coverage. Press [ESC] to stop and exit the test. SPP: Serial Port Profile It is used for ad hoc networking. DUN: Dial-Up Networking Profile DUN Modem - It makes use of a Bluetooth modem or mobile phone as a wireless modem. DUN GPRS – It makes use of a mobile phone with GPRS functionality and connects to GPRS AP.
Chapter 3 System Menu SPP Master Set the mobile computer as a master device. 1. Pairing with your computer (slave) must be completed first. 2. Run the utility “EchoTest.exe” on your computer. Associated settings include - Select “RS-232” for interface. - Use the Bluetooth COM port that has been paired. - Set Action Mode to “Passive”. 3. Start the echo test on both ends. The mobile computer will try to connect to PC (slave). SPP Slave Set the mobile computer as a slave device. 1.
8600 Series Mobile Computer Reference Manual DUN GPRS The mobile computer will try to connect to a mobile phone with GPRS functionality. 1. Pairing with your mobile phone must be completed first. Select “DialUp Network” for Target Machine options. 2. Run the utility “EchoTest.exe” on your computer. Associated settings include - Select “TCP/IP – Server” for interface. - Set Action Mode to “Passive”. 3. Start the echo test on both ends. 4. Enter the server IP on the mobile computer. 5.
Chapter 3 System Menu 3.9.5 PAIRING TEST The pairing procedure is for the creation and exchange of a link key between two Bluetooth-enabled devices. The devices use the link key for future authentication when exchanging information. 1) The mobile computer will start with making an inquiry so that the system can generate a list of device(s) that has been discovered nearby. 2) Select a desired target device. For the device name, it can only display a maximum length of 11 characters.
8600 Series Mobile Computer Reference Manual 3.9.6 FREQUENT DEVICES Here is a list of devices that the mobile computer has been connected to lately. After each successful pairing, the system will update it. This list can show information of one device that provides any of the following services: Serial Port (SPP) Dial-Up Networking (DUN) Human Interface Device (HID) FTP Server (FTP) For the device name, it can only display a maximum length of 11 characters.
Chapter 3 System Menu 3.10 WI-FI MENU This submenu accesses the settings of 802.11b/g wireless networking. You must configure these parameters correctly to be able to make the connection. Note: The menu is available only when the Wi-Fi module is present. Wi-Fi Settings Default Value Network Setting Ad-hoc Infrastructure Items Need to Be Checked DHCP Enable --- v SubNet Mask 255.255.128.0 v v Local IP Address 0.0.0.0 v v Default Gateway 0.0.0.0 --- v DNS Server 0.0.0.
8600 Series Mobile Computer Reference Manual 3.10.1 INFORMATION Information of network configuration can be viewed here. Wi-Fi Menu | 1. Information Lib Kernel version All user libraries reside in Kernel; no external libraries are required. Ver Firmware version of the Wi-Fi module MAC MAC address of the Wi-Fi module IAM A name given to the mobile computer for identification. By default, it is made up of model number and the serial number. (Identical to 3. WLAN Setting | 1.
Chapter 3 System Menu 3.10.2 NETWORK SETTING Set parameters for IP networking. DHCP Options — Enable or Disable Subnet Mask Enter a new Mask IP, if necessary. Local IP Address Enter a new address for the mobile computer, if necessary. Default Gateway Enter a new address for the default Gateway, if necessary. DNS Server Enter a new address for the DNS server, if necessary. Domain Name The domain name of the host is displayed when DHCP server is enabled.
8600 Series Mobile Computer Reference Manual 3.10.3 WLAN SETTING Wireless networking can operate in two modes – (1) Ad-hoc mode: peer-to-peer, and (2) Infrastructure mode: point to multi-point through access points. Set the following parameters. Local Name Enter a name for identifying the mobile computer. By default, it is made up of model number and the serial number. SS ID This refers to Service Set Identifier or AP name, which is used for remote device association.
Chapter 3 System Menu Fixed BSSID This refers to the use of a specific AP’s MAC address as the fixed Basic Service Set Identifier. The mobile computer can ONLY communicate with this one and only access point. Scan Time Specify the time period the mobile computer searches for wireless devices on the network. Normal: By default the scanning time is set to normal. Double: specify double the scanning period.
8600 Series Mobile Computer Reference Manual 3.10.4 SECURITY Set or modify security parameters. WEP: EAP: WPA: Wired Equivalent Privacy Extensible Authentication Protocol Wi-Fi Protected Access Authentication [1] Open System [0] Share Key Default authentication type Enable (For Share Key, it must be enabled!) This requires implementing WEP key.
Chapter 3 System Menu WPA Passphrase Enter a phrase as your password (8 ~ 63 characters) 3.10.5 SCAN DEVICES Select this command to launch the scanning for the Wi-Fi hotspots within range. The mobile computer will first produce a scanning screen and then a result screen that displays all the WiFi hotspots discovered whether open or secured. Select an entry on the result screen to see more details about it including the BSSID, BSS Type, and the security framework it applies.
00 Series Mobile Computer Reference Manual 3.10.6 PROFILE This function allows users to create up to four Wi-Fi profiles. SSID Enter the SSID (up to 32 characters). Ad-Hoc This refers to peer-to-peer mode, without going through access points. Options — Enable or Disable Authentication [1] Open System [0] Share Key Default authentication type Enable (For Share Key, it must be enabled!) This requires implementing WEP key.
Chapter 3 System Menu WPA Setting WPA2 Setting WPA Passphrase Enable Disable (default) Enable Disable (default) Enter a phrase as your password (8 ~ 63 characters) 75
8600 Series Mobile Computer Reference Manual 3.10.7 ECHO TESTS This function is used to measure the coverage of the range, estimate the number of APs and mobile computers needed, and determine the topology of deploying APs. Client Mode Set the mobile computer as a client. Enter the IP address of a server to which the mobile computer connects. Then, it will try to connect to an AP. 1. Run the utility “EchoTest.exe” on your computer. Associated settings include - Select “TCP/IP – Server” for interface.
Chapter 3 System Menu The changing icon indicates 8600 is processing a pre-share key. Wait for a few seconds. The antenna icon will become ready and flashes to indicate 8600 is connecting to an access point under the same SSID. Once connected, the antenna icon will stop flashing. Next to the icon, the more bars, the stronger the signal. Note: If you are programming in C or BASIC, be aware that the antenna icon will appear on the device screen after NetInit() or START TCPIP() is called.
8600 Series Mobile Computer Reference Manual Once the connection of echo test is established, the details will be displayed as illustrated below. SNR (dB) T RSS (-dBm) NF (-dBm) (Signal to Noise ratio) (Transmit Speed) (Received Signal Strength Level) (Noise Floor Level) Very Poor 1 Mbps 0 ~ 60 10 ~ 20 Poor 2 Mbps 60 ~ 75 Moderate 92 ~ 98 Moderate 20 ~ 30 Fair 5.
Chapter 4 PROGRAM MANAGER & KERNEL This chapter explains Program Manager and Kernel that manage multiple programs and firmware upgrade. IN THIS CHAPTER 4.1 Program Manager ...................................................... 79 4.2 Kernel ...................................................................... 86 4.1 PROGRAM MANAGER The mobile computer supports multiple applications and languages.
8600 Series Mobile Computer Reference Manual 4.1.1 DOWNLOAD PROGRAM Here provides a list of programs currently stored on the mobile computer with size information. Multiple application programs can be downloaded through a variety of interfaces. Upon completion of downloading, you are allowed to input a name for the program. If there is no need to rename the program, simply press [ENTER] to leave as it is. The length of program name can be up to 12 characters. Program size is in kilobytes.
Chapter 4 Program Manager & Kernel SPARE MEMORY SECTORS (1 ~ 6) Additional program files can be directly downloaded to these sectors. Download a program file to an empty sector: 1. Press the arrow keys [Up] and [Down] to select an empty sector, and then press [ENTER]. 2. Select a desired interface for downloading. 3. Connect the interface cable if required, and wait for a few seconds to establish a connection… 4. To abort the action, press [ESC]. Then press [ESC] again to return to the menu.
8600 Series Mobile Computer Reference Manual 4.1.2 ACTIVATE PROGRAM The list shows the entire spare programs stored on the mobile computer. From the list, you can select from the memory sector (1 ~ 6) or SD card. The selected program will be copied to the active memory sector and replace the current one. Note: A font file cannot be activated. TO CLEAR FILE SYSTEM When screen appears, “Press [ESC] to clear file” means the file system in the SRAM will be cleared out by pressing [ESC].
Chapter 4 Program Manager & Kernel 4.1.3 UPLOAD PROGRAM You may duplicate one of the programs from the mobile computer to a host computer or another mobile computer. This can be used to clone software on mobile computers. The procedures are similar to that for downloading programs. If the target is “Terminal”, only the “RS232” and “Bluetooth” interface options are available. If the target is “PC”, the available interface options include “RS232”, “USB VCOM”, “Bluetooth” and “USB VCOM_CDC”.
8600 Series Mobile Computer Reference Manual 4.1.4 DOWNLOAD FONT The terminal computer can be loaded with up to 6 font files. Users can input characters in fonts loaded on the device. 4.1.5 UPLOAD FONT You may duplicate one of the fonts from the mobile computer to a host computer or another mobile computer.
Chapter 4 Program Manager & Kernel 4.1.6 UPLOAD ALL You may duplicate all of the programs/fonts from the mobile computer to another one or a host computer. Note: To clone all of the programs, the target mobile computer cannot have any other program downloaded except the active one; that is, Memory Sectors 1 ~ 6 must be empty! You can determine to upload programs only, or clone programs and fonts altogether. If the target is “Terminal”, only the “RS232” and “Bluetooth” interface options are available.
8600 Series Mobile Computer Reference Manual 4.2 KERNEL The kernel resides in the innermost core of the system. It has the highest security and is always protected by the system. When the application program is corrupted and System Menu fails at the same time, Kernel Menu provides an access to fix the system. Warning! Kernel Menu is NOT for the use of any end users. How to access Kernel Menu? 1) When the last session is in System Menu or Program Manager, simply turn off the mobile computer.
Chapter 4 Program Manager & Kernel 4.2.1 KERNEL INFORMATION Here provides important system information to help diagnose the system. Kernel Menu | 1. Information H/W Hardware version S/N Serial number of the mobile computer M/D Manufacturing date BL Bootloader version KNL Kernel version DEV 4-digit code for optional hardware configurations Refer to Understanding Device Code.
8600 Series Mobile Computer Reference Manual 4.2.2 KERNEL UPDATE The kernel and bootloader might need to be updated to improve performance or due to other considerations. Refer to Appendix I Download Utility. The procedure of downloading a kernel (K8600.shx) or bootloader (BL8600.shx) update is like downloading a program. Any attempt to download an older version of bootloader will be rejected. The system will restart itself right after downloading.
Chapter 4 Program Manager & Kernel KERNEL UPDATE VIA BLUETOOTH 1) Go to Kernel Menu | 4. System Menu | 8. Next Page | 2. Bluetooth Menu | 3. Security, and configure the following Bluetooth settings first. Authentication PIN code 2) Go to Kernel Menu | 2. Kernel Update and select Bluetooth. 3) Start the pairing procedure from your computer, for example, click [Pair Device] and/or [Connect Bluetooth Serial Port]. 4) Run the download utility: ProgLoad.
8600 Series Mobile Computer Reference Manual 4) Press [ENTER] to confirm downloading the program file to the mobile computer. Press [ESC] to abort the download task. 4.2.3 BURN-IN TEST This tool is provided for manufacturing use. Warning! You should not perform this test. 4.2.4 SYSTEM MENU Refer to System Menu for details. This submenu is the same as System Menu for system configuration.
SPECIFICATIONS Model Designation 8600 8630 8660 Performance CPU ARM Cortex-M3, 180 MHz Memory Program memory – 8 MB flash Data memory – onboard SRAM, options include 8 or 16 MB Expansion micro SD Slot with SDHC support Main Battery Rechargeable Li-ion battery – 3.7 V, 1100/2200 mAh Expected Battery Life 75/150 hrs (1100/2200 mAh) Backup Battery 16/32 hrs 35/70 hrs Rechargeable Lithium button cell – 3.0 V, 18mAh Data Retention: 25 days Wireless Communications WLAN − 802.
8600 Series Mobile Computer Reference Manual User Environment Operating Temperature -10 ~ 60 °C (14 ~ 140 °F) Storage Temperature -20 ~ 70 °C (-4 ~ 158 °F) Humidity (non-condensed) 10% to 90% (operating) / 5% to 95% (storage) Ingress Protection IP65 Impact Resistance Drop:1.8m/6ft. (5 drops each side onto concrete) Tumble: 1m/3.28ft.
Appendix I DOWNLOAD UTILITY For easy development of applications, the mobile computer ships with FORGE Application Generator programs, batch and WLAN versions, as well as a download utility. FILE TYPES Depending on the file type, you may download a program or font file via System Menu, Program Manager or Kernel Menu.
8600 Series Mobile Computer Reference Manual BASIC PROGRAMS First, download a BASIC runtime (e.g. B8600.SHX) via System Menu or Program Manager. Then, it will allow you to download a BASIC program (.SYN) via System Menu.
Appendix I Download Utility PROGLOAD.EXE The utility “ProgLoad.exe” is provided for you to download a program (*.SHX, *.SYN or *. BIN) to the mobile computer. Run the program on your computer. The following dialog box pops up. Click to select Comm type, COM port, and Baud rate. Choose your file… Communication Type RS-232/IrDA Connection via direct RS-232 cable, IrDA port, or Bluetooth SPP Cradle-IR Connection via cradle TCP/IP Connection over networks File Type .
8600 Series Mobile Computer Reference Manual 96
Appendix II TROUBLESHOOTING CANNOT TURN ON WHEN PRESSING POWER KEY Make sure the battery pack is installed properly. Re-charge the battery inside the mobile computer and monitor the charging status. (See 3.5 Power.) If the battery is faulty, replace it with a fresh and fully charged battery then. CHARGING ERROR If using the USB cable for direct charging, make sure a suitable charging current is selected. (See 3.2.9 USB Charge Current.
8600 Series Mobile Computer Reference Manual KEYPAD SEEMS NOT WORKING Perform the keyboard test. (See 3.3.4 Keyboard.) If the problem persists, reload the battery pack and perform the test again. VIBRATOR SEEMS NOT WORKING Perform the vibrator test. (See 3.3.7 Vibrator.) If the problem persists, reload the battery pack and perform the test again. MOBILE COMPUTER SEEMS NOT WORKING Upload all data to the host and perform the memory test. (See 3.3.5 Memory.
Appendix III Troubleshooting OUT OF SCANNING RANGE Try adjusting the scanning distance from the scanner to the barcode. CANNOT TRANSMIT/RECEIVE DATA USING RS-232 CABLE Check if the RS-232 connection is correct and secured. Make sure the serial port parameters on the host are configured to match the serial parameters on the mobile computer. Try to establish connection again.
8600 Series Mobile Computer Reference Manual KEY REFERENCE TABLE 29-KEY KEYPAD SYSTEM DEFAULTS Key Blue key pressed once Blue key pressed twice Key Orange key pressed once Orange key pressed twice 1 @ @ F1 F5 F1 2 ABC abc F2 F6 F2 3 DEF def F3 F7 F3 4 GHI ghi F4 F8 F4 5 JKL jkl SP Tab SP 6 MNO mno BkSp Del BkSp 7 PQRS pqrs 8 TUV tuv 9 WXYZ wxyz 0 /* /* - +$_ +$_ .
Appendix III Key Reference Table EXTENDED FUNCTION KEYS Key Blue key pressed once Blue key pressed twice Key Orange key pressed once Orange key pressed twice 1 @ @ 1 F11 1 2 ABC abc 2 F12 2 3 DEF def 3 F13 3 4 GHI ghi 4 F14 4 5 JKL jkl 5 F15 5 6 MNO mno 6 F16 6 7 PQRS pqrs 7 F17 7 8 TUV tuv 8 F18 8 9 WXYZ wxyz 9 F19 9 0 /* /* 0 F20 0 - +$_ +$_ - F9 - . %# %# . F10 .
8600 Series Mobile Computer Reference Manual 39-KEY KEYPAD SYSTEM DEFAULTS Key Blue key pressed once Blue key pressed twice Key Orange key pressed once Orange key pressed twice 1 A a 1 : 1 2 B b 2 ; 2 3 C c 3 , 3 + D d + = + 4 E e 4 < 4 5 F f 5 > 5 6 G g 6 ( 6 - H h - ) - 7 I i 7 $ 7 8 J j 8 ? 8 9 K k 9 & 9 * L l * @ * . M m . . 0 N n 0 0 # O o # % # / P p / \ / 102
Appendix III Key Reference Table Key Blue key pressed once Blue key pressed twice Key Orange key pressed once Orange key pressed twice F1 Q q F1 F11 F1 F2 R r F2 F12 F2 F3 S s F3 F13 F3 F4 T t F4 F14 F4 F5 U u F5 F15 F5 F6 V v F6 F16 F6 F7 W w F7 F17 F7 F8 X x F8 F18 F8 F9 Y y F9 F19 F9 F10 Z z F10 F20 F10 SP _ _ SP Tab SP BKSP BkSp BkSP BkSp Del BkSp NCC 警語： 依據低功率電波輻射性電機管理辦法: 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號使用者均不得擅自變更頻率、加大 功率或變更原
8600 Series Mobile Computer Reference Manual FCC: THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Federal Communications Commission Requirements The equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to part 15 of the FCC Rules.
