TERMINAL Model Name: M0010 Version 1.
Copyright © 2007 CIPHERLAB CO., LTD. All rights reserved The software contains proprietary information of CIPHERLAB CO., LTD.; it is provided under a license agreement containing restrictions on use and disclosure and is also protected by copyright law. Reverse engineering of the software is prohibited. Due to continued product development this information may change without notice.
IMPORTANT NOTICES FCC REGULATIONS This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This laser component emits FDA / IEC Class 2 laser light at the exit port. Do not stare into beam. CARE & MAINTENANCE This mobile computer is intended for industrial use. The mobile computer is rated IP 64, however, it may do damage to the mobile computer when being exposed to extreme temperatures or soaked wet. When the body of the mobile computer gets dirty, use a clean and wet cloth to wipe off the dust. DO NOT use/mix any bleach or cleaner. Always keep the LCD dry.
RELEASE NOTES VERSION DATE NOTES 1.00 Initial release Aug.
CONTENTS IMPORTANT NOTICES ..............................................................................................................3 FCC Regulations.....................................................................................................................3 Safety Precautions .................................................................................................................3 Care & Maintenance.......................................................................................
9400 Mobile Computer Reference Manual 1.7 Communications ...........................................................................................................26 1.7.1 Using the Cradle ....................................................................................................26 1.7.2 Inserting the SIM Card ...........................................................................................28 1.7.3 Turn off the Wireless Networks............................................................
Terminal Reference Manual 4.3.2 RFID Reader Settings .............................................................................................81 4.3.3 Data Output ...........................................................................................................82 4.3.4 Beeper / Vibrator ...................................................................................................84 4.3.5 Symbology Settings ....................................................................................
INTRODUCTION The terminal Series, running Windows CE 5.0 in palm size, is our first product line of rugged PDA-style Mobile Computer. Light-weight, streamlined and ergonomic, it adds even more powerful and handy tools to delivering the flexibility in customization. Specifically designed to work as an industrial PDA, the terminal Series provides rich options of data collection, voice and data communications, long-lasting working hours, and so on.
Terminal Reference Manual GETTING FAMILIARIZED WITH TERMINAL Figure 1: Front / Back View 2
INSTALLING THE HAND STRAP The hand strap is ideal for one-handed operation, which requires safe and convenient hold of the mobile computer. Warning: Always make sure the hand strap is well hooked and screwed to the back of the mobile computer before use. When the hand strap is desired, install it to the mobile computer by following these steps: 1) Place the mobile computer face down on a flat and clean surface. 2) Screw one end of the hand strap to the back of the mobile computer.
Terminal Reference Manual INSTALLING THE PISTOL GRIP This contoured pistol grip enables intuitive trigger-and-scan operation, which is very helpful in scan intensive applications. When a pistol grip is necessary, install it to the mobile computer by following these steps: 1) Press for the mobile computer to enter suspend mode. 2) Place the mobile computer face down on a flat and clean surface. 3) Remove the hand strap as well as the side plates as shown below.
Figure 3: Installing the Pistol Grip 5
Terminal Reference Manual DIMENSIONS Figure 4: Dimensions FEATURES Ergonomic design - ruggedized yet streamlined, with hand strap for secure hold. Built tough to survive drop test and sealed against moisture/dust to industrial standard IP 64. Microsoft Windows CE 5.
64 MB / 128 MB SDRAM to store and run programs, as well as store program data One miniSD expansion slot for memory card Dual mode support - One scan engine (integrated barcode scanner/imager) plus one RFID reader Total wireless solution - connectivity includes Bluetooth and 802.11b/g . A 3.5" color transflective TFT display delivers excellent visibility in all lighting conditions. Programmable feedback includes speaker and vibrator.
Terminal Reference Manual Programming support includes Reader DLL and System API. Accessories and peripherals include pistol grip, international AC charging cradle, etc. INSIDE THE PACKAGE The following items are included in the package. Save the box and packaging material for future use in case you need to store or ship the mobile computer.
Chapter 1 USING THE TERMINAL This chapter explains the features and usage of the terminal. IN THIS CHAPTER 1.1 Battery ........................................................................................ 9 1.2 Memory .................................................................................... 15 1.3 Keypad..................................................................................... 18 1.4 Touch Screen........................................................................... 21 1.
Terminal Reference Manual 1.1.1 INSERTING THE BATTERY When you first receive the package, the rechargeable functionality of the backup battery is turned off. It is controlled by a DIP switch inside the battery compartment as shown below. For shipping and storage purposes, save the mobile computer and the main battery in separate packages, and adjust the DIP switch to the OFF position (bottom). This will keep both batteries in good condition for future use.
Chapter 1 3) Hold the mobile computer still and press the release button to unlock the battery cover. 4) Slide off the battery cover. 5) Use the stylus (or a sharp-pointed object, such as a pencil) to adjust the DIP switch to the ON position (top). Now the internal backup battery can be charged by the main battery. 6) Insert the battery pack into the battery compartment at a proper angle (30°~45°) so that the metal contacts on the battery are met with the charging contacts inside the compartment.
Terminal Reference Manual 1.1.2 CHARGING THE BATTERY The main and backup batteries may not be charged to full for shipment. When you first receive the package, you will need to charge batteries to full before using the mobile computer. Note: To charge the batteries to full, it requires approximately 8 hours for the first time. After the initial charging, it takes only 4 hours to charge the batteries to full.
Chapter 1 1.1.3 UNDERSTANDING THE BATTERY ICONS The battery pack is the only power source for the mobile computer to work. It also charges the backup battery on the main board so that the data stored in SRAM can be retained properly. Therefore, when the main battery charge goes low (see below for battery status icon), you need to replace the battery pack with a charged one or charge it as soon as possible.
Terminal Reference Manual Stop wireless connectivity, Bluetooth, or 802.11b that is not in use. Refer to the Wireless Power Manager. To save power, go to Start > Settings > Control Panel and select Display (for backlight settings) or select Power (for power schemes). Warning: Using backlight, wireless connectivity, and peripherals while on battery power will substantially reduce battery life.
Chapter 1 1.2 MEMORY Read-only Memory (ROM) 128 megabytes flash memory for storing OS (Windows CE 5.0) and custom application programs. Yet a small portion of the memory is referred to as DiskOnChip, which can store data and programs that you wish to retain even after a hardware reset. Random-access Memory (RAM) 64 or 128 megabytes SDRAM for storing and running programs, as well as storing program data. Its contents will be retained by the backup battery.
Terminal Reference Manual SDRAM STORAGE MEMORY (LEFT) PROGRAM MEMORY (RIGHT) 64 MB / 128 MB onboard It refers to the memory allocated for file and data storage. It refers to the memory allocated for running programs. (DESKTOP) MY DEVICE > DISKONCHIP The DiskOnChip is part of the onboard 128 MB flash memory. Because the flash memory is non-volatile, data or programs stored in DiskOnChip will not be erased after a hardware reset.
Chapter 1 START > SETTINGS > CONTROL PANEL AND DOUBLE-TAP THE STORAGE MANAGER ICON Here provides a tool for administrators to reformat the DiskOnChip folder or storage card (miniSD). Warning: This tool is for the use of system administrators only. Everything on the storage device will be permanently erased after reformatting. 1.2.
Terminal Reference Manual Figure 6: Inserting the miniSD Card REMOVING THE MINISD CARD If you wish to remove the miniSD card, simply push the card after removing the side plate. The miniSD card will be rejected automatically. 1.3 KEYPAD Silicon rubber has been chosen for their durability and prompt feedback. The 28-key keypad includes alphanumeric, navigation, function keys, and so on. This keypad is set to numeric mode by default.
Chapter 1 Figure 7: 28-key Layout Note: Functionality of keys is application-dependent. 1.3.1 USING THE KEYPAD PRESS FIRST, AND THEN The LED backlight of keypad is turned off by default. It can be toggled ON/OFF by the key combination: [Func] + [0]. START > SETTINGS > CONTROL PANEL AND DOUBLE-TAP THE KEYBOARD ICON The Character Repeat functionality is enabled by default. You may cancel the check box to disable it. When enabled, tap, hold, and drag the slider for a desired Repeat Delay and Repeat Rate.
Terminal Reference Manual 1.3.3 FUNCTION KEY The [Func] (function) key serves as a modifier key. 1) To enable this modifier key, press on the keypad. A circular icon of the letter "F" will appear on the status bar. This modifier key is hold down as long as the icon is displayed. 2) Now press another key to get the value of key combination (say, press [1] to get the value of F1). The icon will go off now. 3) To get the value of another key combination modified by the [Func] key, repeat the above steps.
Chapter 1 1.3.4 PROGRAMMABLE KEYS Two user-definable keys, named P1 and P2, are provided on the keypad. Together with the SCAN key as well as the four side triggers on each side of the touch screen, they can be re-defined as another key or to serve as a shortcut key for launching a specific program. Refer to the Button Assignment Utility. Note: By default, the four side triggers are programmed to serve as ENTER keys (upper ones) as well as SCAN keys (lower ones). 1.
Terminal Reference Manual The LED backlight of screen, which helps ease reading under dim environments, can be controlled manually and automatically. Warning: Using backlight while on battery power will substantially reduce battery life. It is suggested to dim the backlight while working in a well-lit area or automatically turn off the mobile computer when not in use. 1.4.
Chapter 1 3) Tap the [Advanced] button (right above). 4) In the Settings tab, you can select the luminosity of backlight when it is set to be automatically turned on by pressing any key or tapping the screen. Tap, hold, and drag the slider for AC and battery powered respectively. For more luminosity, move the slider to the right.
Terminal Reference Manual 1.4.2 RE-CALIBRATING THE SCREEN This LCD is also a touch screen that can be calibrated through screen alignment. START > SETTINGS > CONTROL PANEL AND DOUBLE-TAP THE STYLUS ICON Tap the Calibration tab, and then tap the [Recalibrate] button. Warning: DO NOT use any pointed or sharp objects to move against the surface of the screen. 1.5 NOTIFICATIONS 1.5.1 STATUS LED The tri-color LED on top is used to provide information on the charging status or wireless power status.
Chapter 1 Charging done On --- --- Good Read On --- --- Bluetooth enabled --- --- On Note: The green LED is also used for "Good Read" while collecting data. 1.5.2 AUDIO Speaker The mobile computer is integrated with a mono speaker, a low power transducer type, used for playing sounds applied to events in Windows and programs, as well as playing audio files such as .WAV files. In addition, it can be programmed for status feedback. Headset A headset jack is provided, which is a 2.
Terminal Reference Manual 1.5.3 VIBRATOR The mobile computer is integrated with a vibrator, which is software programmable for feedback. This can be helpful when working in noisy environments. 1.6 DATA CAPTURE 1.6.1 BARCODE & RFID READER A wide variety of scan engines is available for delivering flexibility to meet different requirements.
Chapter 1 4) The cradle is ready for charging. 5) Seat the mobile computer in the cradle. If data communications are desired at the same time, you can establish a proper connection with a computer or remote host. For example, you may establish a USB connection for ActiveSync. Make sure that you have Microsoft ActiveSync installed on your computer before you connect the USB cable from the cradle's USB device port ( computer. ) to your Refer to section 2.3 Using ActiveSync.
Terminal Reference Manual Figure 8: Understanding the Cradle 1.7.2 INSERTING THE SIM CARD 1) Press for the mobile computer to enter suspend mode. 2) Hold the mobile computer still and remove the hand strap as well as the battery. 3) Use your finger to slide the locking plate towards its hinge to unlock the SIM card holder.
Chapter 1 Figure 9: Inserting the 4) Flip up the SIM card holder. SIM Card 5) Insert the SIM card to the SIM card holder, using the card orientation shown below. 6) Push the SIM card holder down. 7) Slide the locking plate away from its hinge to secure the SIM card holder. 1.7.3 TURN OFF THE WIRELESS NETWORKS The mobile computer supports state-of-the-art wireless technologies, Bluetooth and 802.11b/g, so that it is able to send/receive data in real time in an efficient way.
Terminal Reference Manual 30
Chapter 2 LEARNING WINDOWS CE BASICS This chapter mainly describes the basic skills to work with the terminal. The add-on utilities for applications regarding data collection, processing, and transmission, are introduced in the following chapters. The terminal is specifically designed for real-time data collection in the Windows CE 5.0 environment. It won't take long for any Windows user to get familiarized with it. Keep these basic skills in mind and explore this Windows CE device at ease.
Terminal Reference Manual SUSPEND MODE Like your PDA, Pocket PC and most handheld devices, the terminal functions when it is turned on. This is because the Windows CE operating system eliminates the booting process and runs continuously. Turn On (= Resume from Suspend) To turn on the mobile computer, simply press . Turn Off (= Suspend) To turn off the mobile computer, press Menu. again, or select Suspend from the Start The system is now ready for use but not in use.
Chapter 2 2.1.1 DESKTOP The desktop appears when the mobile computer is turned on (left below). Tap and hold anywhere blank on the screen to manage or configure the desktop (right below). Alternatively, you may tap to the right of the taskbar, and then select Desktop.
Terminal Reference Manual Note: To customize the desktop, tap anywhere blank on the desktop and select Properties. When you turn on the mobile computer and seat it in the cradle for the first time, you will find these icons displayed on the taskbar. Refer to section 2.1.2 Taskbar for more information on the icons. ICON DESCRIPTION SEE ALSO This icon shows that your cradle is directly connected to a computer via USB port. 1.7.1 Using the Cradle Make sure you have Microsoft ActiveSync installed on 2.
Chapter 2 UNDERSTANDING THE ICONS ON THE TASKBAR ICON DESCRIPTION SEE ALSO The USB connection for ActiveSync operation is successfully 3.2.1 USB established. Connection (via cradle) Double-tap it to view status. Tap [Disconnect] if necessary. The Bluetooth PAN connection fails. (= disconnected) 3.2.4 BTPAN The Bluetooth PAN connection is successfully established through the Bluetooth Manager utility. Double-tap it to view or renew IP Information. It provides control of the power to the 802.
Terminal Reference Manual It indicates the current input mode of keypad. The other icons are . It indicates the modifier key is enabled. (= function mode) 2.1.3 START MENU Tap the Start button on the taskbar to open the Start Menu. 36 1.3.4 Alpha Key 1.3.
Chapter 2 OPTIONS DESCRIPTION Programs Provides access to available programs in the directory: \Windows\Programs Favorites Provides access to your favorites in the directory: \Windows\Favorites Documents Provides access to recent opened documents in the directory: \Windows\Recent Settings Provides access to Run... Runs a program or application. Suspend Enters the Suspend mode.
Terminal Reference Manual USING THE SOFT INPUT PANEL (SIP) Tap the SIP button on the taskbar to select a SIP mode or hide the input panel. In each mode, the characters appear as typed text on the screen. OPTIONS DESCRIPTION Keyboard To type using the virtual keyboard. Transcriber To write freely on the screen in applications, such as WordPad, Inbox, etc. 2.
Chapter 2 DEVICE CONFIGURATION CODE The device configuration of terminal is displayed in 5 digits: xxxx-x Take the screenshot of System Properties below for example.
Terminal Reference Manual 3rd digit RFID module 0= none 1= RFID reader 4th digit Reserved --- 5th digit Keypad module 0= 28-key 2.3 USING ACTIVESYNC ActiveSync is used to synchronize information between the terminal and your desktop computer, to install programs on the mobile computer, and to backup and restore the mobile computer. The Microsoft ActiveSync program has to be installed on your desktop computer first.
Chapter 2 Connect the USB cable from the cradle's USB device port ( computer. ) to your Connect the power cable from the cradle to a nearby power outlet. Turn on the mobile computer and seat it in the cradle. 2) Your computer will automatically detect the USB device. Click [OK] when the connection is established. 3) Select which partnership to set up.
Terminal Reference Manual ALTERNATIVE TO INSTALL NEW PROGRAMS (COPY & PASTE) Alternatively, you may install a new program manually. 1) When connected, open the Microsoft ActiveSync window on your desktop computer. 2) Click the Explorer button from the toolbar. 3) Navigate to the target folder, e.g. the Programs folder, depending on where you wish to access the program. 4) Navigate through file folders on your computer to find the new program (.CAB, .EXE, etc.
Chapter 2 2.3.3 BACKUP/RESTORE To best protect your work, you should regularly back up information on your mobile computer. You can perform a backup by during the ActiveSync operation. The backup file is stored on your desktop computer. 2.4 MANAGING PROGRAMS 2.4.1 QUICK LAUNCH A PROGRAM Tap the Start button to view the Start Menu. To quick launch a program, tap it from the Programs folder. Note: Alternatively, you may tap Start and select Run to run a specific program or open a document.
Terminal Reference Manual If you wish to quick launch a new program, add it to the Programs folder: My Device\Windows\Programs. The program will become available in the Start Menu. To add a new program or subfolder to the Programs folder, you can either use Windows Explorer or ActiveSync. Windows Explorer: to move the program by [Copy] and [Paste Shortcut]. ActiveSync on the desktop computer: to create a shortcut to the program, and place the shortcut in the Programs folder.
Chapter 2 4) Navigate to the Programs folder – My Device\Windows\Programs (right above). 5) Tap and hold anywhere blank on the screen to select [Paste Shortcut] from the pop-up menu. The new program will be added to the Programs folder. 6) Go to Start > Programs and the new program will appear now. USING ACTIVESYNC TO ADD A PROGRAM TO START MENU 1) When connected, open the Microsoft ActiveSync window on your desktop computer.
Terminal Reference Manual 2) Click the Explorer button from the toolbar. 3) Navigate through file folders to find the program you desire. 4) Right-click the program and select [Create Shortcut] from the pop-up menu. 5) Right-click the shortcut and select [Cut] from the pop-up menu. 6) Navigate to the Programs folder – My Device\Windows\Programs. 7) Right-click anywhere blank on the window and select [Paste] from the pop-up menu. The new program will be added to the Programs folder.
Chapter 2 2.4.2 CREATE A FOLDER USING WINDOWS EXPLORER TO ADD A NEW FOLDER 1) Go to Start > Programs and select Windows Explorer. 2) Navigate through file folders to find where you wish to create a new folder. 3) Right-click anywhere blank on the window and select [New Folder] from the pop-up menu. A subfolder will be created. USING ACTIVESYNC TO ADD A NEW FOLDER 1) When connected, open the Microsoft ActiveSync window on your desktop computer. 2) Click the Explorer button from the toolbar.
