Instructions

ManualsBrandsCircutor ManualsNetwork Analysis DevicesNetwork diagnostics 3-phase Clamp meter

Table Of Contents

INSTRUCTION MANUAL

Portable power analyzer

MYeBOX 150, MYeBOX 1500

(M084B01-03-19A)

MEASURING EQUIPMENT

E237816

Summary of content (94 pages)

PAGE 1
Portable power analyzer MYeBOX 150, MYeBOX 1500 INSTRUCTION MANUAL (M084B01-03-19A) MEASURING EQUIPMENT E237816
PAGE 2
MYeBOX 150 - MYeBOX 1500 2 Instruction Manual
PAGE 3
MYeBOX 150 - MYeBOX 1500 SAFETY PRECAUTIONS Follow the warnings described in this manual with the symbols shown below. DANGER Warns of a risk, which could result in personal injury or material damage. ATTENTION Indicates that special attention should be paid to a specific point.
PAGE 4
MYeBOX 150 - MYeBOX 1500 CONTENTS SAFETY PRECAUTIONS ��3 DISCLAIMER ��3 CONTENTS ��
PAGE 5
MYeBOX 150 - MYeBOX 1500 6.1.- SETUP MENU: MEASURE SETUP �� 61 6.1.1.- RATED VOLTAGE �� 61 6.1.2.- PRIMARY VOLTAGE �� 62 6.1.3.
PAGE 6
MYeBOX 150 - MYeBOX 1500 REVISION LOG Table 1: Revision log. Date Revision Description 10/16 M084B01-03-15A Initial Version 11/16 M084B01-03-16A Changes in the following sections: 1. - 3.2. - 3.5. - 11. 10/17 M084B01-03-17A Changes in the following sections: 3.2. - 3.5. - 3.8. - 4.2. - 4.2.1. - 4.5.2. - 4.8.2.3. - 5.6. - 6.1.- 6.3.4. - 11.- 14. 02/18 M084B01-03-18A Changes in the following sections: 3.2.- 3.4.- 11. 06/18 M084B01-03-18B Changes in the following sections: 4.2. - 4.8.2.3.
PAGE 7
MYeBOX 150 - MYeBOX 1500 1.- VERIFICATION UPON RECEPTION Check the following points when you receive the device: a) The device meets the specifications described in your order. b) The device has not suffered any damage during transport. c) Perform an external visual inspection of the device prior to switching it on. d) Check that it has been delivered with the following: Kit A_MYeBOX 150 and Kit A_MYeBOX 1500: - An installation guide. - 1 battery. - 1 AC power supply adaptor. - 1 Wi-Fi antenna.
PAGE 8
MYeBOX 150 - MYeBOX 1500 2.- PRODUCT DESCRIPTION MYeBOX is a portable analyzer that measures, calculates and displays the main parameters of any electrical installation (single-phase, two-phase with and without neutral, balanced or unbalanced three-phase and through an ARON connection) MYeBOX can be fully configured remotely and can display electrical parameters on a smartphone or tablet using a mobile application connected to a Wi-Fi network. There are 2 device models:  MYeBOX 150.  MYeBOX 1500.
PAGE 9
MYeBOX 150 - MYeBOX 1500 - 1 μUSB connector to connect and download data to a PC. The MYeBOX mobile application lets you fully program the MYeBOX remotely, configure the measurement, display the most important parameters and send logs to MYeBOX Cloud.
PAGE 10
MYeBOX 150 - MYeBOX 1500 3.- DEVICE INSTALLATION 3.1.
PAGE 11
MYeBOX 150 - MYeBOX 1500 3.2.- BATTERY INSTALLATION Do not disassemble or modify the battery. The warranty does not cover any battery not delivered by Circutor or batteries that have been disassembled or modified. There is a risk of explosion if installed incorrectly. To avoid possible damage: - Only install the batteries supplied or recommended by Circutor. - Keep the battery away from fire and high-temperature lights. - Do attempt to disassemble it. - Do not expose it to water. - Do not short-circuit it.
PAGE 12
MYeBOX 150 - MYeBOX 1500 Figure 2:Removal of the battery cover. Connect the battery, Figure 3. Figure 3:Connect the battery. Insert the connection cable inside the battery cover, Figure 4. Figure 4:Insert the connection cable inside the battery cover. Insert the battery into its correct position and replace the cover. (Figure 5) Be careful not to pinch the battery cables when inserting it.
PAGE 13
MYeBOX 150 - MYeBOX 1500 Figure 5: Inserting the battery. Disconnect the battery if the device is going to be idle for more than 3 months. If the device has been without power for more than 4 weeks, it is recommended to load a few hours before use. The battery reaches its maximum capacity after it is fully charged and discharged a few times. Do not charge the battery at temperatures above 40ºC or below 0ºC. Battery charger selected is not for outdoor use. 3.3.
PAGE 14
MYeBOX 150 - MYeBOX 1500 To install the strap on the device, follow these steps: Figure 7: Installation of the fastening strap: Steps 1 and 2. Figure 8: Installation of the fastening strap: Steps 3 and 4. 3.4.- MYeBOX 480V ~ PSU ADAPTER : POWER SUPPLY ADAPTER Note : The MYeBOX 480V ~ power supply adapter is an accessory sold separately. The MYeBOX 480V~ PSU ADAPTER is a highly efficient universal power supply adapter, designed to power and charge the MYeBOX portable power analyser.
PAGE 15
MYeBOX 150 - MYeBOX 1500 Table 3 (Continuation): MYeBOX 480V~ PSU ADAPTER Technical features. Output Environmental features Operating temperature 0ºC ... +40ºC Storage temperature -20ºC ... +70ºC Relative Humidity (non-condensing) 5 ... 95 % Maximum altitude 2000 m Protection degree IP30 Mechanical features Dimensions 78.8 x 78.8 x 53.1 mm Weight 168 g.
PAGE 16
MYeBOX 150 - MYeBOX 1500 3.5.- VOLTAGE CABLES To measure voltage, you must use 600 V CAT III double-insulated connection cables. The Kit B_MYeBOX 150 and Kit B_MYeBOX 1500 kits come with the necessary cables: - UL 600 V CAT III double-insulated voltage cables, or higher. - UL 600 V CAT III crocodile clamps Coloured markers are included with the devices to identify the measuring channels according to each country's standard. Table 4: Cable colours: European (IEC 60445 :2010).
PAGE 17
MYeBOX 150 - MYeBOX 1500 Table 5 (Continuation):Clamps and transformers for measuring the phase current and the neutral current. Type Scale Measurement range Accuracy(1) Transformer .../ 0.250A 1% ... 200% In 0.5% (1% ... 200% In) (1) Accuracy is given by the following measurement conditions for input 2V: exclusion of errors produced by the clamps and external voltage transformers, with a range in temperature of 5 ... 45 ºC and power factor 0 ... 1.
PAGE 18
MYeBOX 150 - MYeBOX 1500 Table 8:List of terminals on the upper face of the MYeBOX 150. Device terminals on the upper face of the MYeBOX 150 9: Power Supply, auxiliary power supply. 10: μUSB, μUSB connector. 9 10 Figure 11:MYeBOX 150 terminals, upper face. 3.7.2.- MYeBOX 1500 Table 9:List of terminals on the lower face of the MYeBOX 1500.
PAGE 19
MYeBOX 150 - MYeBOX 1500 11 12 16 14 13 15 17 18 Figure 13:MYeBOX 1500 terminals, upper face.
PAGE 20
MYeBOX 150 - MYeBOX 1500 3.8.- CONNECTION DIAGRAMS 3.8.1.- THREE-PHASE NETWORK MEASURING WITH A 4-WIRE CONNECTION, MYeBOX 150. Type of installation (Select circuit)(3): 3 Phases + Neutral. ALIMENTACIÓN AUXILIAR POWER SUPPLY eBOX 150 MY U1 U2 U3 UN I1 I2 I3 IN L1 L2 L3 N CARGA / LOAD Figure 14: Three-phase measuring with a 4-wire connection (MYeBOX 150). Note: See section “3.8.10.- DETAIL OF THE CURRENT MEASUREMENT CONNECTION.” (3) 20 See “5.2.
PAGE 21
MYeBOX 150 - MYeBOX 1500 3.8.2.- THREE-PHASE NETWORK MEASURING WITH A 4-WIRE CONNECTION, MYeBOX 1500. Type of installation (Select circuit)(4): 3 Phases + Neutral. ALIMENTACIÓN AUXILIAR POWER SUPPLY MY eBOX 1500 U1 U2 U3 UN URef I1 I2 I3 IN L1 L2 L3 N CARGA / LOAD Figure 15: Three-phase measuring with a 4-wire connection (MYeBOX 1500). Note: See section “3.8.10.- DETAIL OF THE CURRENT MEASUREMENT CONNECTION.” (4) See “5.2.
PAGE 22
MYeBOX 150 - MYeBOX 1500 3.8.3.- THREE-PHASE NETWORK MEASURING WITH A 3-WIRE CONNECTION, MYeBOX 150 AND MYeBOX1500. Type of installation (Select circuit)(5): 3 Phases. ALIMENTACIÓN AUXILIAR POWER SUPPLY MY eBOX 150 U1 U2 U3 I1 I2 I3 L1 L2 L3 CARGA / LOAD Figure 16: Three-phase measuring with a 3-wire connection (MYeBOX 150, MYeBOX 1500). Note: See section “3.8.10.- DETAIL OF THE CURRENT MEASUREMENT CONNECTION.” (5) 22 See “5.2.
PAGE 23
MYeBOX 150 - MYeBOX 1500 3.8.4.- THREE-PHASE NETWORK MEASURING WITH A 3-WIRE CONNECTION AND ARON CONNECTION, MYeBOX 150 AND MYeBOX 1500. Type of installation (Select circuit)(6): Aron. ALIMENTACIÓN AUXILIAR POWER SUPPLY MY eBOX 150 U1 U2 U3 I1 I3 L1 L2 L3 CARGA / LOAD Figure 17: Three-phase measuring with a 3-wire connection and an ARON connection (MYeBOX 150, MYeBOX 1500). Note: See section “3.8.10.- DETAIL OF THE CURRENT MEASUREMENT CONNECTION.” (6) See “5.2.
PAGE 24
MYeBOX 150 - MYeBOX 1500 3.8.5.- TWO-PHASE NETWORK MEASURING WITH A 3-WIRE CONNECTION, MYeBOX 150. Type of installation (Select circuit)(7): 2 Phases + Neutral. ALIMENTACIÓN AUXILIAR POWER SUPPLY eBOX 150 MY U1 U2 UN I1 I2 IN L1 L2 N CARGA / LOAD Figure 18: Two-phase measuring with a 3-wire connection (MYeBOX 150). Note: See section “3.8.10.- DETAIL OF THE CURRENT MEASUREMENT CONNECTION.” (7) 24 See “5.2.
PAGE 25
MYeBOX 150 - MYeBOX 1500 3.8.6.- TWO-PHASE NETWORK MEASURING WITH A 3-WIRE CONNECTION, MYeBOX 1500. Type of installation (Select circuit)(8): 2 Phases + Neutral. ALIMENTACIÓN AUXILIAR POWER SUPPLY MY eBOX 1500 U1 U2 UN URef I1 I2 IN L1 L2 N CARGA / LOAD Figure 19: Two-phase measuring with a 3-wire connection (MYeBOX 1500). Note: See section “3.8.10.- DETAIL OF THE CURRENT MEASUREMENT CONNECTION.” (8) See “5.2.
PAGE 26
MYeBOX 150 - MYeBOX 1500 3.8.7. - SINGLE-PHASE NETWORK MEASUREMENT, PHASE TO PHASE, WITH A 2-WIRE CONNECTION, MYeBOX 150 AND MYeBOX 1500. Type of installation (Select circuit)(9): 2 Phases. ALIMENTACIÓN AUXILIAR POWER SUPPLY MY eBOX 150 U1 U2 I1 L1 L2 CARGA / LOAD Figure 20: Single-phase measurement, phase to neutral, with a 2-wire connection (MYeBOX 150, MYeBOX 1500). Note: See section “3.8.10.- DETAIL OF THE CURRENT MEASUREMENT CONNECTION.” (9) 26 See “5.2.
PAGE 27
MYeBOX 150 - MYeBOX 1500 3.8.8.- SINGLE-PHASE NETWORK MEASUREMENT, PHASE TO NEUTRAL, WITH A 2-WIRE CONNECTION, MYeBOX 150. Type of installation (Select circuit)(10): 1 Phase + Neutral. ALIMENTACIÓN AUXILIAR POWER SUPPLY MY eBOX 150 U1 UN I1 L1 N CARGA / LOAD Figure 21: Single-phase measurement, phase to neutral, with a 2-wire connection (MYeBOX 150). Note: See section “3.8.10.- DETAIL OF THE CURRENT MEASUREMENT CONNECTION.” (10) See “5.2.
PAGE 28
MYeBOX 150 - MYeBOX 1500 3.8.9.- SINGLE-PHASE NETWORK MEASUREMENT, PHASE TO NEUTRAL, WITH A 2-WIRE CONNECTION, MYeBOX 1500. Type of installation (Select circuit)(11): 1 Phase + Neutral. ALIMENTACIÓN AUXILIAR POWER SUPPLY MY eBOX 1500 U1 UN URef I1 L1 N CARGA / LOAD Figure 22: Single-phase measurement, phase to neutral, with a 2-wire connection (MYeBOX 1500). Note: See section “3.8.10.- DETAIL OF THE CURRENT MEASUREMENT CONNECTION.” (11) 28 See “5.2.
PAGE 29
MYeBOX 150 - MYeBOX 1500 3.8.10.- DETAIL OF THE CURRENT MEASUREMENT CONNECTION. eBOX 1500 Figure 23: Detail of the current measurement connection. 3.8.11.- LEAKAGE CURRENT CONNECTION, ILeak. (MYeBOX 1500 MODEL) CARGA /LOAD ILeak L1 L2 L3 N Figure 24: Connection of the leakage current, ILeak (MYeBOX 1500).
PAGE 30
MYeBOX 150 - MYeBOX 1500 3.9.- REGISTERING AND UPDATING THE DEVICE Before using the device for the first time, it is necessary to: 1.- Register the MYeBOX on the web page www.myebox.es 2.- Register the device on a network with Internet connection. 3.- Download the latest version of the mobile application MYeBOX, which can be found in the App Store and on Google Play. 4.- Connect to the device from the mobile application. 5.
PAGE 31
MYeBOX 150 - MYeBOX 1500 4.- OPERATION 4.1.- OPERATING PRINCIPLE The MYeBOX is a four-quadrant portable power analyzer (consumption and generation).
PAGE 32
MYeBOX 150 - MYeBOX 1500 4.2.- MEASUREMENT PARAMETERS The device measures and logs different types of parameters:  Electrical parameters,  Quality parameters (EVQ) such as overvoltages, gaps and outages, in accordance with EN50160.  Wave shapes of the different channels. All the measurement parameters can be viewed on the MYeBOX mobile application, as shown in Table 11. Table 11: MYeBOX measurement parameters.
PAGE 33
MYeBOX 150 - MYeBOX 1500 Table 11 (Continued): MYeBOX measurement parameters. Parameter No. of hours of active tariff (12) Cost (12) CO2 Emissions (12) (12) Parameters shown on the device's display. Units hours COST kgCO2 Tariff: T1-T2    4.2.1.- QUALITY PARAMETERS Power quality control requires defining the TRMS of the voltage level, subsequently used by the analyzer to record events.
PAGE 34
MYeBOX 150 - MYeBOX 1500  Transients Transients are detected by checking that the difference between one sample and the next does not exceed the maximum nominal slope value multiplied by the distortion level coefficient selected by the user (“6.3.4.- TRANSIENTS, DISTURB”). In this case 128 samples are checked per cycle. The maximum nominal slope value is the maximum tangent value calculated using a nominal value selected by the user.
PAGE 35
MYeBOX 150 - MYeBOX 1500 Figure 30:Transients detected with a distortion coefficient of 90.0. 4.3.- KEYPAD FUNCTIONS The MYeBOX has 5 capacitive keys and 2 buttons: Table 12: Button functions. Button Press Device on/off button. Data logging start/end button. When the device's off button is pressed, the screen shown in Figure 31 appears to confirm the shut-down. POWER OFF YES Figure 31:Device shut-down screen (1). Use the and keys to select whether or not to turn off the device.
PAGE 36
MYeBOX 150 - MYeBOX 1500 Table 13: Key functions: Display menus. Key Press Go to the previous display screen. Go to the next display screen. Access the display menu. Access the setup menu from the Setup menu Go to the next display menu. Go to the previous display menu. Table 14: Key functions: Setup menus. Key Press Go to the previous configuration screen. Move the cursor one position to the left in edit mode. Go to the next display screen. Move the cursor one position to the right in edit mode.
PAGE 37
MYeBOX 150 - MYeBOX 1500 4.5.- LED INDICATORS 4.5.1.- MYeBOX 150. The MYeBOX 150 model has 14 indicator LEDs, as shown in Figure 34 and Table 15. Wifi Memory Battery ON USB REC MY DATE TIME 25/06/2015 15:07:50 U1 U2 U3 UN I1 I2 I3 IN Figure 34:MYeBOX 150 indicator LEDs. Table 15: LED description, MYeBOX 150. LED ON Wi-Fi Description Power off Device off. Blinking light (1 s) Device on. Power off Wi-Fi connection disabled. Power on Wi-Fi connection enabled.
PAGE 38
MYeBOX 150 - MYeBOX 1500 Table 15 (Continued): LED description, MYeBOX 150. LED Description Power on Green: Battery charge between 70 ... 100 %. Yellow: Battery charge between 30 ... 70 %. Red: Battery charge between 5 ... 30 %. Blinking light (1 s) Battery Green: Battery not charging, charge between 70 ... 100 %. Yellow: Battery not charging, charge between 30 ... 70 %. Red: Battery not charging, charge between 5 ... 30 %. Blinking light (0.5 s) Red: Battery not charging, charge < 5%.
PAGE 39
MYeBOX 150 - MYeBOX 1500 Table 15 (Continued): LED description, MYeBOX 150. LED IN Description Power off Clamp not connected (LN) Power on Clamp connected (LN) 4.5.2.- MYeBOX 1500. The MYeBOX 1500 model has 21 indicator LEDs, as shown in Figure 35 and Table 16. Wifi 3G Battery ON IN1 IN2 OUT1 OUT2 USB REC MY DATE TIME 25/06/2015 15:07:50 U1 U2 U3 UN URef I1 Memory I2 I3 IN ILeak Figure 35:MYeBOX 1500 indicator LEDs. Table 16: LED description, MYeBOX 1500.
PAGE 40
MYeBOX 150 - MYeBOX 1500 Table 16 (Continued): LED description, MYeBOX 1500. LED Description Power off 3G connection disabled. Power on 3G 3G connection enabled. Blinking light (1 s) 3G traffic. Power on Green: Battery charge between 70 ... 100 %. Yellow: Battery charge between 30 ... 70 %. Red: Battery charge between 5 ... 30 %. Blinking light (1 s) Battery Green: Battery not charging, charge between 70 ... 100 %. Yellow: Battery not charging, charge between 30 ... 70 %.
PAGE 41
MYeBOX 150 - MYeBOX 1500 Table 16 (Continued): LED description, MYeBOX 1500. LED U1 U2 U3 UN URef I1 I2 I3 IN ILeak Description Power off No voltage at the corresponding input. (U1: L1, U2: L2, U3: L3, UN: LN, URef: Reference voltage) Power on Voltage at the corresponding input.
PAGE 42
MYeBOX 150 - MYeBOX 1500 4.8.- DATA LOGGING 4.8.1. DATABASE The MYeBOX has a database that logs all the device's parameters and events. To begin logging data, push the button. When the button is pushed, the screen shown in Figure 36 appears to confirm the beginning of recording. RECORDING YES Figure 36:Recording confirmation screen. Use the and keys to select whether or not the device should record. And press the key to confirm the option. Press the button again to end logging.
PAGE 43
MYeBOX 150 - MYeBOX 1500 The device only recognises cards in FAT32 format. If a MicroSD memory card in another format is used, the device will not be able to write to it and a write error will be indicated by the REC LED blinking. We recommend not using cards that have information you wish to keep, and backing up the information frequently for security purposes. A ZIP file containing three file types is saved to the MicroSD memory: A *.
PAGE 44
MYeBOX 150 - MYeBOX 1500 Table 18 (Continued):.EVA file description.
PAGE 45
MYeBOX 150 - MYeBOX 1500 4.8.2.3. .STD file The standard (.STD) file is used to store all the parameters that have to be recorded periodically, within a programmed period of time. Table 20 shows the variables that can be included in an STD file.
PAGE 46
MYeBOX 150 - MYeBOX 1500 Table 20 (Continued) : List of variables that can be included in the STD file Variables Direct current Inverse current Current maximum demand Active power maximum demand Aparent power maximum demand Variables Cost CO2 Emissions (15) Default recording period.
PAGE 47
MYeBOX 150 - MYeBOX 1500 Asymmetry coefficient, Ka: ratio between the homopolar and direct components in an unbalanced system. |𝑈𝑈0 | 100 |𝑈𝑈𝑑𝑑 | |𝑈𝑈0 | coefficient. Equation 𝐾𝐾𝑎𝑎1:%Asymmetry = 100 |𝑈𝑈𝑑𝑑 | 𝐾𝐾𝑎𝑎 % = | |𝑈𝑈𝑖𝑖inverse Unbalance coefficient, Kd: ratio between the and direct components in an unbal𝐾𝐾𝑑𝑑 % = 100 anced system |𝑈𝑈𝑑𝑑 | 𝐾𝐾𝑑𝑑 % = |𝑈𝑈𝑖𝑖 | 100 |𝑈𝑈𝑑𝑑 | Equation 2:Unbalance coefficient.
PAGE 48
MYeBOX 150 - MYeBOX 1500 4.8.2.4.- Removing the MicroSD memory card. To avoid electric shocks, disconnect the measuring and power supply terminals before opening the cover. Do not use the device without the cover in place. The MicroSD memory card is located under the battery. To remove it, follow the steps indicated in section “3.2.- BATTERY INSTALLATION”. The position of the MicroSD memory card is shown in Figure 37. Figure 37: Location of the MicroSD memory card.
PAGE 49
MYeBOX 150 - MYeBOX 1500 5.- DISPLAY The parameters shown by the device on the screen are organised into different display menus, as shown in Figure 38. MEASURE Measures DEVICE PROFILE Device profile QUALITY Quality COMMUNICATIONS Communications DATE/TIME Date INFORMATION Information ENERGY RATIOS Energy ratios SETUP MENU Configuration menus Figure 38:MYeBOX display menu.
PAGE 50
MYeBOX 150 - MYeBOX 1500 Once the device has finished booting up, the display shows the first screen of the Measure display menu, as shown in Figure 39. VL1 230.0 VL2 230.0 VL3 230.0 Figure 39:Phase-neutral voltage screen, measure menu. If the device detects a system error, the error screen appears as shown in Figure 40, indicating the error code. This screen disappears by pressing any key or button on the unit. SISTEM VERIFIED CODE ERROR: 0x01FE Figure 40: Error code screen.
PAGE 51
MYeBOX 150 - MYeBOX 1500 5.1.- DISPLAY MENU: MEASURE Figure 42 shows the main screen of the Measure display menu, showing all the device’s measuring parameters. MEASURE Figure 42:Measure display menu, main screen. Press the Use the key to enter the display menu. and keys to toggle between the different screens. Table 22: Measure display menu. Measure display menu VL1 230.0 VL2 230.0 VL3 230.0 Phase - Neutral Voltages, VL1, VL2 and VL2 VL12 398.0 VL23 VL31 400.0 401.
PAGE 52
MYeBOX 150 - MYeBOX 1500 Table 21 (Continued): Measure display menu. Measure display menu COS1 -0.80 COS2 -1.00 COS3 -0.50 Cos φ, of each of the phases.(16) COS l l l 1.00 PF l l l -0.95 Cos φ III and Power Factor III (16) kvrC l l l 34500 kvrL l l l 34500 Three-phase Capacitive Reactive Power and three-phase Inductive Reactive Power. (16) kW l l l 34500 kVA l l l 33450 Three-phase Active Power and three-phase Apparent Power. (16) FREQ kWh l l l 50.00 00999999.
PAGE 53
MYeBOX 150 - MYeBOX 1500 5.2.- DISPLAY MENU: DEVICE PROFILE Figure 43 shows the main screen of the Device Profile display menu, showing all the device's profile. DEVICE PROFILE Figure 43:Device Profile display menu, main screen. Press the Use the key to enter the display menu. and keys to toggle between the different screens. Table 23: Device Profile display menu. Device Profile display menu DEVICE NAME MYeBOXService Name of the device, defined in the setup menu.
PAGE 54
MYeBOX 150 - MYeBOX 1500 5.3.- DISPLAY MENU: QUALITY Figure 44 shows the main screen of the Quality display menu, showing all the device's quality parameters. QUALITY Figure 44:Quality display menu, main screen. Press the Use the key to enter the display menu. and keys to toggle between the different screens. Table 24: Quality display menu. Quality display menu NOMINAL VOLTAGE 163.00 Rated voltage SWELL SAG INTERRU 105 113 205 Detected events meter: SWELL, no. of overvoltages detected. SAG, no.
PAGE 55
MYeBOX 150 - MYeBOX 1500 5.4.- DISPLAY MENU: COMMUNICATIONS Figure 45 shows the main screen of the Communications display menu, showing full information about the device's active communications. COMMUNICATIONS Figure 45:Communications display menu, main screen. Press the Use the key to enter the display menu. and keys to toggle between the different screens. Table 25: Communications display menu.
PAGE 56
MYeBOX 150 - MYeBOX 1500 Table 24 (Continued): Communications display menu. Communications display menu Note: Screen visible on the MYeBOX 1500 model 3G SIGNAL 86 % Level of 3G signal, value between 0% and 100%. Note: Screen visible on the MYeBOX 1500 model IMEI 357784047309511 IMEI code (International Mobile Station Equipment Identity) MAIN MENU Press the key to quit the display menu. 5.5.
PAGE 57
MYeBOX 150 - MYeBOX 1500 5.6.- DISPLAY MENU: INFORMATION Figure 47 shows the main screen of the Information display menu, showing full information about the device. INFORMATION Figure 47:Information display menu, main screen. Press the Use the key to enter the display menu. and keys to toggle between the different screens. Table 27: Information display menu. Information display menu MEMORY SPACE 75 % Memory space available.
PAGE 58
MYeBOX 150 - MYeBOX 1500 Table 28: Code error Error bit Description Action 0x0000 There is no error - 0x0001 Memory (DDR) error Turn the device off and then on again. If the problem persists contact the Technical Assistance Service. 0x0002 0x0004 0x0006 MicroSD memory error Check that the MicroSD memory card has been inserted correctly in its slot. If the problem persists contact the Technical Assistance Service.
PAGE 59
MYeBOX 150 - MYeBOX 1500 Table 29 (Continued) : Energy Ratios display menu Menú de visualización Measure hourT12 costT15.25244 No. of hours of the active Tariff 1 (Energy Generated) Cost per kWh of Tariff 1 (Energy Generated) KgCO2T1125.85855 CO2 emissions of Tariff 1 (Energy Generated) hourT2+ 1 costT2+ 2.32160 No. of hours of the active Tariff 2 (Energy Consumed) Cost per kWh of Tariff 2 (Energy Consumed) KgCO2T2+ 150.70044 CO2 emissions of Tariff 2 (Energy Consumed) hourT25 costT27.85165 No.
PAGE 60
MYeBOX 150 - MYeBOX 1500 6.- CONFIGURATION The device's configuration is organised into different menus, as shown in Figure 49. SETUP MENU MEASURE SETUP Measures DEVICE PROFILE SETUP Device profile QUALITY SETUP Quality COMMUNICATIONS SETUP Communications MEMORY SETUP Memory RESET FACTORY SETUP Factory setting (18) (8) SERVICE SETUP Service MAIN MENU Display menus Figure 49:MYeBOX configuration menu.
PAGE 61
MYeBOX 150 - MYeBOX 1500 If from any setup menu screen no key is pressed for 5 minutes, the device quits the setup menu and returns to the Phase-Neutral Voltages screen of the Measure display menu. Note: Setup menu changes must be made while data logging is off. 6.1.- SETUP MENU: MEASURE SETUP Figure 50 shows the main screen of the Measure setup menu, where the device’s measurement parameters are configured. MEASURE SETUP Figure 50:Measure setup menu, main screen. Press the key to enter the setup menu.
PAGE 62
MYeBOX 150 - MYeBOX 1500 6.1.2.- PRIMARY VOLTAGE This screen is used to configure the primary winding of the voltage transformer. PRIMARY VOLTAGE 000001 Press the Use the key to enter edit mode. and keys to write or change the value of the blinking digit. When the value on the screen is as desired, use the sor. and keys to move the editing cur- Minimum configuration value: 1 V. Maximum configuration value: 500000 V. Press the Use the key to confirm.
PAGE 63
MYeBOX 150 - MYeBOX 1500 6.1.4.- PHASE CLAMP SCALE This screen is used to select the scale of the clamps selected for measuring the phase. Note: If the clamp only has one scale, this parameter cannot be edited. PHASE CLAMP SCALE LOW Press the key to enter edit mode. Use the keys and to browse the different options: Hi, MEDIUM or LOW. (See “3.5.- CURRENT CLAMPS”). Press the Use the key to confirm the option selected. and keys to toggle between the menu’s setup screens. 6.1.5.
PAGE 64
MYeBOX 150 - MYeBOX 1500 6.1.6.- NEUTRAL CLAMP SCALE This screen is used to select the scale of the clamp selected for measuring the neutral. Note: If the clamp only has one scale, this parameter cannot be edited. NEUTRAL CLAMP SCALE LOW Press the key to enter edit mode. Use the keys and to browse the different options: Hi, MEDIUM or LOW. (See “3.5.- CURRENT CLAMPS”). Press the Use the key to confirm the option selected. and keys to toggle between the menu’s setup screens. 6.1.7.
PAGE 65
MYeBOX 150 - MYeBOX 1500 6.1.8.- CLAMP SCALE FOR MEASURING THE LEAKAGE CURRENT, ILeak Note: Configuration parameter available for the MYeBOX 1500 model. This screen is used to select the scale of the clamp selected for measuring the leakage current. Note: If the clamp only has one scale, this parameter cannot be edited. LEAK CLAMP SCALE LOW Press the key to enter edit mode. Use the keys and to browse the different options: Hi, MEDIUM or LOW. (See “3.5.- CURRENT CLAMPS”).
PAGE 66
MYeBOX 150 - MYeBOX 1500 6.1.10.- FREQUENCY This screen is used to select the operating frequency. FREQ HZ 50.00 Press the Use the key to enter edit mode. and keys to browse the different options: 50.00, 50 Hz. 60.00, 60 Hz, Press the Use the key to confirm the option selected. and keys to toggle between the menu’s setup screens. 6.1.11.- SAVE key to save the changes and to go to the main screen of the Measure setup Press the menu.
PAGE 67
MYeBOX 150 - MYeBOX 1500 6.2.- SETUP MENU: DEVICE PROFILE SETUP Figure 51 shows the main screen of the Device Profile setup menu where the device's profile can be configured. DEVICE PROFILE SETUP Figure 51:Device Profile setup menu, main screen. Press the key to enter the setup menu. 6.2.1.- NAME OF THE DEVICE This screen is used to configure the name used to identify the device. DEVICE NAME MYeBOXService Press the Use the key to enter edit mode.
PAGE 68
MYeBOX 150 - MYeBOX 1500 6.2.3.- TYPE OF INSTALLATION This screen is used to configure the installation type. SELECT CIRCUIT 3 PHASES + NEUTRAL Press the key to enter edit mode. Use the keys and to browse the different options: 1 PHASE + NEUTRAL, 2-wire connection. 2 PHASES, tion. 2 PHASES 3 PHASES, Single-phase network measurement, phase to neutral, with a Single-phase network measurement, phase to phase, with a 2-wire connec+ NEUTRAL, Two-phase network measurement with a 3-wire connection.
PAGE 69
MYeBOX 150 - MYeBOX 1500 6.3.- SETUP MENU: QUALITY SETUP Figure 52 shows the main screen of the Quality setup menu, where the device's quality parameters are configured. QUALITY SETUP Figure 52:Quality setup menu, main screen. Press the key to enter the setup menu. 6.3.1.- OVERVOLTAGE, SWELL This screen is used to configure the threshold value for logging an overvoltage, as a percentage of the rated voltage value. SOBRETENSION / SWELL 110 % Press the Use the key to enter edit mode.
PAGE 70
MYeBOX 150 - MYeBOX 1500 Minimum configuration value: 50% Maximum configuration value: 97% Note: Set the value to 0 to stop recording gaps. Press the Use the key to confirm. and keys to toggle between the menu's setup screens. 6.3.3.- OUTAGE, INTERRUPTION This screen is used to configure the threshold value for logging outages, as a percentage of the rated voltage value. CORTE / INTERRUPTION 010% Press the Use the key to enter edit mode. and keys to write or change the value of the blinking digit.
PAGE 71
MYeBOX 150 - MYeBOX 1500 Press the Use the key to confirm. and keys to toggle between the menu’s setup screens. 6.3.5.- SAVE Press the key to save the changes and to go to the main screen of the Quality setup menu. SAVE Use the and keys to toggle between the menu’s setup screens. 6.3.6.- EXIT Press the values. key to exit to the main screen of the Quality setup menu without saving modified EXIT Use the and keys to toggle between the menu’s setup screens. 6.4.
PAGE 72
MYeBOX 150 - MYeBOX 1500 NETWORK, Select this option when the unit is going to connect to a previously created corporate Wi-Fi network. ACCESS POINT, After selecting this option, the device generates a Wi-Fi network so the user can connect from the mobile application. Press the key to confirm the option selected. Use the and keys to toggle between the menu's setup screens. 6.4.2.- SSID Note: This configuration parameter cannot be edited if ACCESS POINT was selected for the “6.4.1.
PAGE 73
MYeBOX 150 - MYeBOX 1500 NO, Press the WPS deactivated. key to confirm the option selected. Note: The device activates the WPS after the configuration is saved (“6.4.10.- SAVE”). Use the and keys to toggle between the menu's setup screens. 6.4.4.- PASSWORD Note: This configuration parameter cannot be edited if ACCESS POINT was selected for the “6.4.1.Wi-Fi CONFIGURATION” parameter or YES was selected for the “6.4.3.
PAGE 74
MYeBOX 150 - MYeBOX 1500 6.4.6.- APN, ACCESS POINT NAME Note: Configuration parameter available for the MYeBOX 1500 model. Note: This configuration parameter cannot be edited if DISABLE was selected for the “6.4.5.- EN- ABLING 3G COMMUNICATIONS” parameter. This screen is used to configure the name of the APN for 3G communications. APN NAME VODAFONE Press the Use the key to enter edit mode. and keys to write or change the value of the blinking digit.
PAGE 75
MYeBOX 150 - MYeBOX 1500 6.4.8.- APN, PASSWORD Note: Configuration parameter available for the MYeBOX 1500 model. Note: This configuration parameter cannot be edited if DISABLE was selected for the “6.4.5.- ENABLING 3G COMMUNICATIONS” parameter. This screen is used to configure the APN password for 3G communications. APN PASSWORD ******************** Press the Use the key to enter edit mode. and keys to write or change the value of the blinking digit.
PAGE 76
MYeBOX 150 - MYeBOX 1500 6.4.10.- SAVE Press the key to save the changes and to go to the main screen of the Communications setup menu. SAVE Use the and keys to toggle between the menu’s setup screens. 6.4.11.- EXIT Press the key to exit to the main screen of the Communications setup menu without saving modified values. EXIT Use the and keys to toggle between the menu’s setup screens. 6.5.
PAGE 77
MYeBOX 150 - MYeBOX 1500 Press the Use the key to confirm the option selected. and keys to toggle between the menu’s setup screens. 6.5.2.- SAVE Press the key to begin deletion of the database. SAVE While the deletion is being performed, the following screen will be shown: SD FORMATTING .... At the end of the deletion process, different messages can appear, depending on the result: SD SD SD FORMAT DONE, if the deletion has been correctly performed.
PAGE 78
MYeBOX 150 - MYeBOX 1500 6.6.- SETUP MENU: RESET FACTORY SETUP Figure 55 shows the main screen of the Reset Factory setup menu where the default values of the unit can be loaded. RESET FACTORY SETUP Figure 55: Reset facvtory setup menu, main screen. Press the key to enter the setup menu. 6.6.1.- LOADING THE DEFAULT CONFIGURATION. This screen is used to select whether to load the default configuration in the device, i.e. the original factory settings. RESET FACTORY NO Press the key to enter edit mode.
PAGE 79
MYeBOX 150 - MYeBOX 1500 6.6.3.- EXIT Press the key to exit to the main screen of the Reset Factory setup menu without saving modified values. EXIT Use the and Instruction Manual keys to toggle between the menu’s setup screens.
PAGE 80
MYeBOX 150 - MYeBOX 1500 7.- WIRELESS COMMUNICATIONS The device has the following wireless communications: MYeBOX 150 model: Wi-Fi communications MYeBOX 1500 model: Wi-Fi communications  3G communications 7.1.- USAGE ENVIRONMENT AND HEALTH Wireless communications emit radio frequency electromagnetic energy, like other radio devices. Because wireless communications operate under the guidelines found in radio frequency standards and recommendations, they are safe for users to use.
PAGE 81
MYeBOX 150 - MYeBOX 1500 7.2.- LOCATION OF THE ANTENNAS The device has two antennas for Wi-Fi and 3G connections. 3G ( MYeBOX 1500 ) Wi-Fi Figure 56:Location of the wireless antennas. The antennas have a standard connector so they can be exchanged for larger ones if the application requires greater coverage. 7.3.- Wi-Fi COMMUNICATIONS Wi-Fi is one of the most widely-used wireless technologies today, used to connect electronic devices and exchange information between them without a physical connection.
PAGE 82
MYeBOX 150 - MYeBOX 1500 7.4.- 3G COMMUNICATIONS (MYeBOX 1500 model) The MYeBOX 1500 model has 3G communications, so the device can be connected and exchange data with other mobile devices without a Wi-Fi connection. The only thing required is a SIM card. 3G communications can be configured through the mobile application or by using the device's display. See “6.4.- SETUP MENU: COMMUNICATIONS SETUP” and “5.4.- DISPLAY MENU: COMMUNICATIONS”. Continued use of 3G can reduce battery use.
PAGE 83
MYeBOX 150 - MYeBOX 1500 8.- MOBILE APPLICATION MYeBOX The device has the MYeBOX mobile application, which allows users to wirelessly connect to the devices using Wi-Fi or 3G communications (MYeBOX 1500 model) and: Fully configure the device. Display all parameters in real time, both numerically and graphically. View wave shapes. Download the data log files stored on the MicroSD memory. Program e-mail warnings when alarms occur.
PAGE 84
MYeBOX 150 - MYeBOX 1500 10.2.- UPDATING THROUGH THE MOBILE APPLICATION With MYeBOX switched on: 1.- Open the MYeBOX mobile application. 2.- If there is a new version of the unit, the application indicates this in the Setup / Firmware menu. And asks the user if they want to update the unit. 3.- If the user confirms the update, it is started automatically. Note: After updating the MYeBOX, it will be automatically restarted.
PAGE 85
MYeBOX 150 - MYeBOX 1500 11.- TECHNICAL FEATURES Power supply (AC power supply adaptor) Input 100 ... 240 V ~ Rated voltage Frequency 47 ... 63 Hz Consumption MYeBOX 150 MYeBOX 1500 22... 28 VA 25... 31 VA Installation category CAT II 300 V Output Rated voltage 9V Consumption MYeBOX 150 MYeBOX 1500 18 W 20 W Voltage measurement circuit Voltage measurement margin 10 ...600 V ~ (PH-N) Frequency measurement margin 42.5 ... 69 Hz Input impedance 2.
PAGE 86
MYeBOX 150 - MYeBOX 1500 (Continued) Accuracy of measurements (19) Power factor measurement Class 0.5 (IEC 61557-12) Voltage THD measurement Class I (IEC 61000-4-7) Voltage harmonics (up to 50th order) Class I (IEC 61000-4-7) Current THD measurement Class I (IEC 61000-4-7) Current harmonics (up to 50th order) Class I (IEC 61000-4-7) Pinst Flicker 3 % (IEC 61000-4-15) Pst Flicker 5 % (0.2 ...
PAGE 87
MYeBOX 150 - MYeBOX 1500 User interface Display 20 alphanumeric characters x 2 lines Keypad 5 keys, 2 buttons LED MYeBOX 150: 14 LEDs, MYeBOX 1500: 21 LEDs Connectivity μUSB Internal battery Type Lithium Voltage 3V Capacity 220 mAh Battery life 10 years Battery Type Lithium Voltage 3.7 V Capacity 3700 mAh Charge time 6 hours Charge temperature 0 ...
PAGE 88
MYeBOX 150 - MYeBOX 1500 165.96 255.68 40 Figure 58: MYeBOX dimensions. Standards Electrical equipment for measurement, control and laboratory use EMC requirements - Part 1: General requirements Electrical equipment for measurement, control, and laboratory use Part 1: General Requirements EN 61326-1:2013 UL 61010-1, 3rd Edition, 2012-05-11 Electrical equipment for measurement, control, and laboratory use - CAN/CSA-C22.2 No.
PAGE 89
MYeBOX 150 - MYeBOX 1500 12.- MAINTENANCE AND TECHNICAL SERVICE The device does not need any maintenance. Only clean the screen with soapy water and dry with a soft dry cloth. In the case of any query in relation to device operation or malfunction, please contact the CIRCUTOR, SA Technical Support Service. Technical Assistance Service Vial Sant Jordi, s/n, 08232 - Viladecavalls (Barcelona) Tel: 902 449 459 ( España) / +34 937 452 919 (outside of Spain) email: sat@circutor.com 13.
PAGE 90
MYeBOX 150 - MYeBOX 1500 14.
PAGE 91
MYeBOX 150 - MYeBOX 1500 Instruction Manual 91
PAGE 92
MYeBOX 150 - MYeBOX 1500 92 Instruction Manual
PAGE 93
MYeBOX 150 - MYeBOX 1500 Instruction Manual 93
PAGE 94
CIRCUTOR, SA Vial Sant Jordi, s/n 08232 -Viladecavalls (Barcelona) Tel.: (+34) 93 745 29 00 - Fax: (+34) 93 745 29 14 www.circutor.com central@circutor.