Owner's manual

ManualsBrandsCirrus Logic ManualsHardwareEP93xx

441

442

443

444

445

446

447

448

449

450

Table Of Contents

Contents
- Figures
- Tables
- Revision History
Preface
- P.1 About the EP93xx User’s Guide
- P.2 Related Documents from Cirrus Logic
- P.3 Reference Documents
- P.4 Notational Conventions
- P.5 Register Example
Introduction
- 1.1 Introduction
- 1.2 EP93xx Features
- 1.3 EP93xx Processor Applications
- 1.4 EP93xx Processor Highlights
ARM920T Core and Advanced High-Speed Bus (AHB)
- 2.1 Introduction
- 2.2 Overview: ARM920T Core
- 2.3 AHB Decoder
MaverickCrunch Co-Processor
- 3.1 Introduction
- 3.2 Programming Examples
  - 3.2.1 Example 1
  - 3.2.2 Example 2
    - 3.2.2.1 C Code
    - 3.2.2.2 MaverickCrunch Assembly Language Instructions
- 3.3 DSPSC Register
- 3.4 ARM Co-Processor Instruction Format
- 3.5 Instruction Set for the MaverickCrunch Co-Processor
Boot ROM
- 4.1 Introduction
  - 4.1.1 Boot ROM Hardware Operational Overview
    - 4.1.1.1 Memory Map
  - 4.1.2 Boot ROM Software Operational Overview
- 4.2 Boot Options
System Controller
- 5.1 Introduction
- 5.2 Registers
Vectored Interrupt Controller
- 6.1 Introduction
- 6.2 Registers
Raster Engine With Analog/LCD Integrated Timing and Interface
- 7.1 Introduction
- 7.2 Features
- 7.3 Raster Engine Features Overview
- 7.4 Functional Details
- 7.5 Registers
Graphics Accelerator
- 8.1 Overview
- 8.2 Block Processing Modes
- 8.3 Line Draws
  - 8.3.1 Breshenham Line Draws
  - 8.3.2 Pixel Step Line Draws
- 8.4 Memory Organization for Graphics Accelerator
- 8.5 Register Programming
  - 8.5.1 Word Count
    - 8.5.1.1 Example: 8 BPP mode
    - 8.5.1.2 Example: 24 BPP (packed) mode
  - 8.5.2 Pixel End and Start
- 8.6 Register Usage
- 8.7 Registers
1/10/100 Mbps Ethernet LAN Controller
- 9.1 Introduction
- 9.2 Descriptor Processor
- 9.3 Registers
DMA Controller
- 10.1 Introduction
- 10.2 Registers
  - 10.2.1 DMA Controller Memory Map
  - 10.2.2 Internal M2P/P2M Channel Register Map
Universal Serial Bus Host Controller
- 11.1 Introduction
  - 11.1.1 Features
- 11.2 Overview
- 11.3 Registers
Static Memory Controller
- 12.1 Introduction
- 12.2 Static Memory Controller Operation
- 12.3 PCMCIA Interface (EP9315 Processor Only)
- 12.4 PC Card Memory-Mode Enable Signals
- 12.5 PC Card Memory Mapping
- 12.6 Registers
  - 12.6.1 Bank Configuration Registers
  - 12.6.2 PCMCIA Configuration Registers (EP9315 Processor Only)
SDRAM, SyncROM, and SyncFLASH Controller
- 13.1 Introduction
- 13.2 Booting from SyncROM or SyncFLASH
- 13.3 Address Pin Usage
- 13.4 SDRAM Initialization
- 13.5 Programming Mode Register: SDRAM Or SyncROM Device
- 13.6 SDRAM Self Refresh
  - 13.6.1 Entering Self Refresh Mode
  - 13.6.2 Exiting Self Refresh Mode
- 13.7 Programming Registers: SyncFLASH Device
- 13.8 External Synchronous Memory System
  - 13.8.1 Chip Select SDCSN[3:0] Decoding
  - 13.8.2 Address/Data/Control Required by Memory System
- 13.9 Registers
UART1 With HDLC and Modem Control Signals
- 14.1 Introduction
- 14.2 UART Overview
- 14.3 Modem
- 14.4 HDLC
- 14.5 UART1 Package Dependency
  - 14.5.1 Clocking Requirements
  - 14.5.2 Bus Bandwidth Requirements
- 14.1 Registers
UART2
- 15.1 Introduction
- 15.2 IrDA SIR Block
- 15.3 UART2 Package Dependency
  - 15.3.1 Clocking Requirements
  - 15.3.2 Bus Bandwidth Requirements
- 15.4 Registers
UART3 With HDLC Encoder
- 16.1 Introduction
- 16.2 Implementation Details
- 16.3 Registers
IrDA
- 17.1 Introduction
- 17.2 IrDA Interfaces
- 17.3 Shared IrDA Interface Feature
- 17.4 Medium IrDA Specific Features
  - 17.4.1 Introduction
    - 17.4.1.1 Bit Encoding
    - 17.4.1.2 Frame Format
  - 17.4.2 Functional Description
- 17.5 Fast IrDA Specific Features
- 17.6 Registers
Timers
- 18.1 Introduction
- 18.2 Registers
Watchdog Timer
- 19.1 Introduction
- 19.1 Registers
Real Time Clock With Software Trim
- 20.1 Introduction
  - 20.1.1 Software Trim
  - 20.1.2 Reset Control
- 20.1 Registers
I2S Controller
- 21.1 Introduction
- 21.2 I2S Transmitter Channel Overview
- 21.3 I2S Receiver Channel Overview
  - 21.3.1 Receiver FIFO’s
- 21.4 I2S Master Clock Generation
- 21.5 I2S Bit Clock Rate Generation
  - 21.5.1 Example of the Bit Clock Generation.
  - 21.5.2 Example of Right Justified LRCK format
- 21.6 Interrupts
- 21.7 Registers
AC’97 Controller
- 22.1 Introduction
- 22.2 Interrupts
  - 22.2.1 Channel Interrupts
  - 22.2.2 Global Interrupts
- 22.3 System Loopback Testing
- 22.4 Registers
Synchronous Serial Port
- 23.1 Introduction
- 23.2 Features
- 23.3 SSP Functionality
- 23.4 SSP Pin Multiplex
- 23.5 Configuring the SSP
- 23.6 Registers
Pulse Width Modulator
- 24.1 Introduction
- 24.2 Theory of Operation
  - 24.2.1 PWM Programming Examples
  - 24.2.2 Programming Rules
- 24.3 Registers
Analog Touch Screen Interface
- 25.1 Introduction
- 25.2 Touch Screen Controller Operation
- 25.3 Registers
Keypad Interface
- 26.1 Introduction
- 26.2 Theory of Operation
- 26.3 Registers
IDE Interface
- 27.1 Introduction
- 27.2 Theory of Operation
- 27.3 Registers
GPIO Interface
- 28.1 Introduction
- 28.2 Registers
Security
- 29.1 Introduction
- 29.2 Features
- 29.3 Contact Information
- 29.4 Registers
Glossary
EP93XX Register List

11-4 DS785UM1

Universal Serial Bus Host Controller

EP93xx User’s Guide

11.2.2.2 Data Structures

The basic building blocks for communication across the interface are the Endpoint Descriptor

(ED) and Transfer Descriptor (TD).

The Host Controller Driver assigns an Endpoint Descriptor to each endpoint in the system.

The Endpoint Descriptor contains the information necessary for the Host Controller to

communicate with the endpoint. The fields include the maximum packet size, the endpoint

address, the speed of the endpoint, and the direction of data flow. Endpoint Descriptors are

linked in a list.

A queue of Transfer Descriptors is linked to the Endpoint Descriptor for the specific endpoint.

The Transfer Descriptor contains the information necessary to describe the data packets to

be transferred. The fields include data toggle information, shared memory buffer location, and

completion status codes. Each Transfer Descriptor contains information that describes one or

more data packets. The data buffer for each Transfer Descriptor ranges in size from 0 to 8192

bytes with a maximum of one physical page crossing. Transfer Descriptors are linked in a

queue: the first one queued is the first one processed.

Each data transfer type has its own linked list of Endpoint Descriptors to be processed.

Figure 11-3, Typical List Structure, is a representation of the data structure relationships.

Figure 11-3. Typical List Structure

The head pointers to the bulk and control Endpoint Descriptor lists are maintained within the

operational registers in the HC. The Host Controller Driver initializes these pointers prior to

the Host Controller gaining access to them. Should these pointers need to be updated, the

Host Controller Driver may need to halt the Host Controller from processing the specific list,

update the pointer, then re-enable the HC.

The head pointers to the interrupt Endpoint Descriptor lists are maintained within the HCCA.

There is no separate head pointer for isochronous transfers. The first isochronous Endpoint

Descriptor simply links to the last interrupt Endpoint Descriptor. There are 32 interrupt head

pointers. The head pointer used for a particular frame is determined by using the last 5 bits of

the Frame Counter as an offset into the interrupt array within the HCCA.

The interrupt Endpoint Descriptors are organized into a tree structure with the head pointers

being the leaf nodes. The desired polling rate of an Interrupt Endpoint is achieved by

Head Ptr ED

TDTD

TD TD