REVIEW DRAFT Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide November, 2013 Cisco Systems, Inc. www.cisco.com Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco website at www.cisco.com/go/offices.
REVIEW DRAFT THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
REVIEW DRAFT CONTENTS Preface vii Objectives Audience vii vii Organization viii Conventions viii Related Documents xiv Finding the Product Serial Number xiv Obtaining Documentation, Support, and Security Guidelines CHAPTER 1 Overview xvi 1-1 About the 1532 Access Point Hardware Models 1-2 Regulatory Domains 1-1 1-2 Hardware Features 1-3 Connectors 1-3 1532I/1532E Connectors 1-3 1532I/E Connectors 1-5 Antenna Port Locations 1-7 Radio Operation 1-7 AP1532I (Internal Antenna) 1-8 AP1532E
Contents REVIEW DRAFT CHAPTER 2 Installing the Access Point 2-1 Unpacking the Access Point 2-2 Package Contents 2-2 Tools and Hardware 2-2 Optional Tools and Hardware 2-2 Optional Tools and Hardware That You Supply Warnings 2-3 2-3 Safety Information 2-4 FCC Safety Compliance Statement Safety Precautions 2-4 2-4 Avoiding Damage to Radios in a Testing Environment 2-6 Installation Guidelines 2-7 Site Surveys 2-7 Before Beginning the Installation 2-8 Becoming Familiar with Access Point Installation
Contents REVIEW DRAFT Connecting an Ethernet Cable to the Access Point Connecting Streetlight AC Power 2-39 Connecting a DC Power Cable to the Access Point 2-37 2-42 Configuring the Access Point 2-47 Adding the Access Point MAC Addresses to the Controller Filter List Configuring a RAP 2-47 Configuring a Bridge Group Name 2-48 What to Do Next CHAPTER 3 Troubleshooting 2-47 2-49 3-1 Guidelines for Using the Access Points 3-2 Important Notes 3-2 Convergence Delays 3-2 Bridge Loop 3-3 Controller DH
Contents REVIEW DRAFT Canada B-7 European Union Australia B-7 B-7 Guidelines for Operating Cisco Aironet Access Points in Japan Japanese Translation B-8 English Translation B-8 VCCI Statement for Japan B-9 Administrative Rules for Cisco Aironet Access Points in Taiwan Chinese Translation B-9 English Translation B-10 Chinese Translation B-10 English Translation B-10 Statement 371—Power Cable and AC Adapter B-11 English Translation B-11 EU Declaration of Conformity B-11 Operation of Cisco Aironet Access Po
REVIEW DRAFT Preface This section describes the objectives, audience, organization, and conventions of the Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide. Objectives This publication explains the steps for installing the Cisco Aironet 1530 Series Outdoor Access Point (called the access point in this document). The access point is available in an internal antenna (1532I) or an external antenna (1532E) version. The 1532 model is a dual-radio platform that supports dual-band (2.
REVIEW DRAFT Organization This guide contains the following sections: Chapter Title Description Chapter 1 Overview Describes the major components and features of the access point. Chapter 2 Installing the Access Point Provides warnings, safety information, and mounting information you need to install your access point. Chapter 3 Troubleshooting Provides basic troubleshooting procedures for the access point.
REVIEW DRAFT Convention Description ^ The symbol ^ represents the key labeled Control. For example, the key combination ^D in a screen display means hold down the Control key while you press the D key. <> Nonprinting characters, such as passwords, are in angle brackets. Notes use the following conventions: Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in this manual. Cautions use the following conventions: Caution Means reader be careful.
REVIEW DRAFT Varoitus TÄRKEITÄ TURVALLISUUSOHJEITA Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.
REVIEW DRAFT Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes.
REVIEW DRAFT Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.
REVIEW DRAFT Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide OL-30864-01 xiii
REVIEW DRAFT Related Documents These documents provide complete information about the access point: • Release Notes for Cisco Wireless LAN Controllers and Lightweight Access Points • Quick Start Guide: Cisco Aironet 1530 Series Outdoor Access Points • Cisco Wireless LAN Controller Configuration Guide Click this link to browse to the Cisco Wireless documentation home page: http://www.cisco.com/en/US/products/hw/wireless/index.
REVIEW DRAFT Figure 1 Location of Serial Number Label 390224 SN: XXXNNNNXXXX SN: XXXNNNNXXXX The access point serial number label contains the following information: • Model number, such as AIR-CAP1532E-x-K9. • Serial number, such as WCN0636279B (11 alphanumeric digits). • Access point MAC address, for example 68BDABF54600 (12 hexadecimal digits). It is located under the serial number. You need your product serial number when requesting support from the Cisco Technical Assistance Center.
REVIEW DRAFT Obtaining Documentation, Support, and Security Guidelines For information on obtaining documentation and support, providing documentation feedback, security guidelines, and recommended aliases and general Cisco documents, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html To view all new wireless documentation, click on Wireless.
REVIEW DRAFT CH A P T E R 1 Overview The Cisco Aironet 1530 Series Outdoor Access Point (hereafter called the access point or AP) is a wireless outdoor access point which is designed for use in a variety of network configurations. The access point supports wireless client access, point-to-point bridging, point-to-multipoint bridging, and point-to-multipoint mesh wireless connectivity. About the 1532 Access Point The 1532 access point supports two radios (2.
Chapter 1 Overview Hardware Models REVIEW DRAFT Hardware Models The model numbers (or part numbers) and configuration for the Cisco Aironet 1532 Outdoor Access Points are described in Table 1-1. For a detailed description of the declarations of conformity and regulatory information for the 1532 access points refer to Appendix B, “Declarations of Conformity and Regulatory Information.
Chapter 1 Overview Hardware Features REVIEW DRAFT Hardware Features This section describes the hardware features of the 1532 access point models. The following hardware features are described in this section: • Connectors, page 1-3 • Antenna Port Locations, page 1-7 • Multiple Power Sources, page 1-8 • Ethernet (PoE) Ports, page 1-10 • Optional Hardware, page 1-10 Connectors Figure 1-4 and Figure 1-5 show the access point connectors for all models.
Chapter 1 Overview Hardware Features REVIEW DRAFT Figure 1-2 Access Point Models AIR-CAP1532E-x-K9 Bottom Connectors 2 3 4 347848 1 1 Antenna 1 port 2 Antenna 2 port 3 LAN port 4 POE-in port Figure 1-3 Access Point Model AIR-CAP1532E-x-K9 Top Connectors 2 347847 1 1 Antenna port 4 Note 2 Antenna port 3 The AIR-CAP1532I-x-K9 does not have any top connectors.
Chapter 1 Overview Hardware Features REVIEW DRAFT 1532I/E Connectors Figure 1-4 Access Point Model AIR-CAP1532I-x-K9 and AIR-CAP1532E-x-K Left Side Connectors 347845 1 1 Console port and Reset button (covered) Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide OL-30864-01 1-5
Chapter 1 Overview Hardware Features REVIEW DRAFT Figure 1-5 Access Point Model AIR-CAP1532I-x-K9 and AIR-CAP1532E-x-K Right Side Connectors 2 347846 1 1 DC Power-In (covered) 2 Ground Pad Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide 1-6 OL-30864-01
Chapter 1 Overview Hardware Features REVIEW DRAFT Antenna Port Locations Figure 1-6 shows the antenna port locations for model AIR-CAP1532E-x-K9. The ports used depend on the optional antennas ordered.
Chapter 1 Overview Hardware Features REVIEW DRAFT Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 AP1532I (Internal Antenna) The 1532I access point 802.11b/g/n radio is used primarily for local access and its 802.11a/n radio for wireless backhaul in the Mesh. The 2 GHz b/g/n radio operates in 2.4 GHz ISM band. It supports channels 1-11 in the US, 1-13 in Europe, and 1-13 in Japan.
Chapter 1 Overview Hardware Features REVIEW DRAFT Warning This equipment must be externally grounded using a customer-supplied ground wire before power is applied. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 366 Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.
Chapter 1 Overview Hardware Features REVIEW DRAFT Ethernet (PoE) Ports The access point supports an Ethernet uplink port (PoE-In). The access point Ethernet uplink port uses an RJ-45 connector (with weatherproofing) to link the access point to the 10BASE-T, 100BASE-T or 1000BASE-T network. The Ethernet cable is used to send and receive Ethernet data and to optionally supply inline power from the power injector or a suitably powered switch port.
Chapter 1 Overview Network Deployment Examples REVIEW DRAFT Network Deployment Examples The access point is a wireless device designed for wireless client access and point-to-point bridging, point-to-multipoint bridging, and point-to-multipoint mesh wireless connectivity. The access point provides 5-GHz backhaul capability to link with another access point to reach a wired network connection or to provide repeater operations for other access points.
Chapter 1 Overview Network Deployment Examples REVIEW DRAFT Wireless client access is supported; however, if bridging between tall buildings, the 2.4-GHz wireless coverage area may be limited and possibly not suitable for direct wireless client access. Figure 1-8 Access Point Point-to-Point Bridging Example 255495 (5 GHz) The access points can also support point-to-point bridging under autonomous mode. In this autonomous mode, the bridging can be done on the 2.4 or 5 GHz radio, but not both.
Chapter 1 Overview Network Deployment Examples REVIEW DRAFT Figure 1-10 Access Point to Multipoint Bridging Example (5 GHz) 255494 (5 GHz) The access points can also support point-to-multipoint bridging under autonomous mode. In this autonomous mode, the bridging can be done on the 2.4 or 5 GHz radio, but not both. In this mode, one access point is designated as the root and the other end is designated as the non-root bridge.
Chapter 1 Overview Network Deployment Examples REVIEW DRAFT Point-to-Multipoint Mesh Network The access point is typically deployed in a mesh network configuration. In a typical mesh deployment, one or more RAPs have a wired network connection through a switch to a controller. Other remote MAPs without wired network connections use the backhaul feature to optimally link to a RAP that is connected to the wired network.
Chapter 1 Overview Network Deployment Examples REVIEW DRAFT Layer 3 Network Operation The access points support Layer 3 network operation. Access points and controllers in Layer 3 configurations use IP addresses and UDP packets, which can be routed through large networks. Layer 3 operation is scalable and recommended by Cisco. Figure 1-13 illustrates a typical Layer-3 wireless network configuration containing access points and a controller.
Chapter 1 Overview Network Deployment Examples REVIEW DRAFT Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide 1-16 OL-30864-01
REVIEW DRAFT CH A P T E R 2 Installing the Access Point This chapter describes how to install the 1532 access point and contains the following sections: • Unpacking the Access Point, page 2-2 • Tools and Hardware, page 2-2 • Warnings, page 2-3 • Safety Information, page 2-4 • Avoiding Damage to Radios in a Testing Environment, page 2-6 • Installation Guidelines, page 2-6 • Mounting the Access Point, page 2-11 • Installing Antennas, page 2-27 • Grounding the Access Point, page 2-38 • Po
Chapter 2 Installing the Access Point Unpacking the Access Point REVIEW DRAFT Unpacking the Access Point To unpack the access point, follow these steps: Step 1 Open the shipping container and carefully remove the contents. Step 2 Return all packing materials to the shipping container, and save it. Step 3 Ensure that all items listed in “Package Contents” are included in the shipment. If any item is damaged or missing, notify your authorized Cisco sales representative.
Chapter 2 Installing the Access Point Warnings REVIEW DRAFT • FIPS kit (AIRLAP-FIPSKIT=) • Lightning Arrestor kit (AIR-ACC245LA-N=) Optional Tools and Hardware That You Supply Tools and materials that are user-supplied are: • Ground lug crimping tool (Panduit CT-720 with CD-720-1 die) • 6-AWG copper ground wire • 10 mm open end or box wrench • 13 mm box-end wrench or socket set • Adjustable wrench with opening up to 33 mm and 28 mm socket.
Chapter 2 Installing the Access Point Safety Information REVIEW DRAFT Warning The cables specified in this installation guide that are used with the specified cable glands provide protection against ingress of moisture for a Type 4/IP67 classified enclosure. If substitute cable are used, the installer must ensure that the size (OD) of the cable meets the acceptable range allowed by the cable gland.
Chapter 2 Installing the Access Point Safety Information REVIEW DRAFT Warning To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Statement 1023 Warning This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028 Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Chapter 2 Installing the Access Point Avoiding Damage to Radios in a Testing Environment REVIEW DRAFT • If any part of the antenna system should come in contact with a power line, do not touch it or try to remove it yourself. Call your local power company. They will remove it safely. If an accident should occur, call for qualified emergency help immediately.
Chapter 2 Installing the Access Point Installation Guidelines REVIEW DRAFT Note • Review the FCC guidelines for installing and operating outdoor wireless LAN devices at http://www.cisco.com/en/US/partner/prod/collateral/routers/ps272/data_sheet_c78-647116_ps114 51_Products_Data_Sheet.html. • Perform a site survey before beginning the installation. • Install the access point in an area where structures, trees, or hills do not obstruct radio signals to and from the access point.
Chapter 2 Installing the Access Point Installation Guidelines REVIEW DRAFT • Do you have the proper permits, if required? • Are you following the proper safety procedures and practices? • Have you configured the access points before you go onsite? It is always easier to resolve configurations or device problems first. • Do you have the proper tools and equipment to complete your survey.
Chapter 2 Installing the Access Point Installation Guidelines REVIEW DRAFT Figure 2-1 Components in a Typical Access Point Installation 1 2 9 10 8 3 5 351963 4 7 6 1 Building roof-overhang 6 Ground 2 Shielded outdoor-rated Ethernet (CAT5e or better) cable1 7 Power cord 3 Water drip loop 8 Power injector 9 Shielded Ethernet (CAT5e or better) cable1 4 6-AWG copper grounding wire 5 Ground rod1 1 10 Controller (through a switch) 1. User supplied.
Chapter 2 Installing the Access Point Installation Guidelines REVIEW DRAFT Figure 2-2 Standard Pole Mount Installation 1 5 2 4 3 1 1532 series access point model AIR-CAP1532E-x-K9 3 Mounting bracket (part of pole mount kit) 2 One of four M6 AP mount hole and key hole slots 4 Stainless steel mounting straps (part of pole mount kit) 5 Pole (wood, metal, or fiberglass) 2 in. to 8 in.
Chapter 2 Installing the Access Point Mounting the Access Point REVIEW DRAFT Mounting the Access Point This section provides instructions for installing your access points. Personnel installing the access point must understand wireless access points and bridging techniques and grounding methods. Caution All installation methods for mounting an access point on any wall surface is subject to the acceptance of local jurisdiction.
Chapter 2 Installing the Access Point Mounting the Access Point REVIEW DRAFT Materials Required to Mount Access Point to a Vertical Wall In Kit Two stainless steel band clamps (adjustable 2"–5", 51 mm – 127 mm) Yes Two stainless steel band clamps(adjustable 5"–8", 127 mm – Yes 203 mm) Crimping tool for ground lug, Panduit CT0720 with CD-720-1 die (http://onlinecatalog.paduit.
Chapter 2 Installing the Access Point Mounting the Access Point REVIEW DRAFT Figure 2-4 Mounting Bracket for Wall and Pole Mounting 1 347852 2 3 Step 2 Note 1 Quick Mount Keyhole Slots (for AP use) 3 Bracket Mount Holes (use bolts up to 1/4" or 6 mm in diameter) 2 Mounting Slots (used with the band clamps) Use four customer-supplied screws and optional screw-anchors to attach the mounting plate to the mounting surface.
Chapter 2 Installing the Access Point Mounting the Access Point REVIEW DRAFT Step 3 Screw an M6 x12 mm bolt into each of the four support bolt holes on the back of the access point. Do not screw the bolt all the way in; leave approximately a 0.13 inch (3.3 mm) space. Step 4 Position the four bolts on the access point into the keyhole slots on the mounting bracket. Step 5 Slide the access point down to sit securely in the quick mount notches.
Chapter 2 Installing the Access Point Mounting the Access Point REVIEW DRAFT Step 4 Screw an M6 bolt into each of the four bolt holes on the back side of the access point. Do not screw the bolt in all the way. Leave a gap of about 0.13" (3.3mm). Step 5 Position the four bolts on the access point into the bracket keyhole slots. Check to be sure that the access point is properly seated in the slots.
Chapter 2 Installing the Access Point Mounting the Access Point REVIEW DRAFT Figure 2-6 AP and Fixed Mount Kit Installed on a Pole 1 2 3 351492 4 1 One of four M6 AP mount hole and key hole slots 2 Metal Band Straps 3 Mounting Slots 4 Pole Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide 2-16 OL-30864-01
Chapter 2 Installing the Access Point Mounting the Access Point REVIEW DRAFT Wall Mounting the Access Point with the Pivoting Mounting Kit The optional pivoting mounting kit contains a mounting bracket for wall or pole mounting. This kit can be used to install the access point on a wall while still allowing for some freedom of movement. This bracket supports metal, wood or fiberglass surfaces.
Chapter 2 Installing the Access Point Mounting the Access Point REVIEW DRAFT Materials Required for mounting AP on a vertical wall with pivoting mounting kit In Kit Grounding block No Grounding rod No 13-mm box-end wrench or socket set No 10-mm box-end wrench No AP wall mounted with Pivoting Mounting Kit 351322 Figure 2-8 Caution The mounting surface, attaching screws and optional wall anchors must be able to support a 50-lb (22.7 kg) static weight.
Chapter 2 Installing the Access Point Mounting the Access Point REVIEW DRAFT Step 4 Match the holes in the bracket plate to the holes in the back of the access point. Step 5 Screw an M8 x12 mm bolt into each of the four bolt holes (using a 10 mm box wrench or socket, torque the bolts to 40 lbf-in) on the back side of the access point and mounting bracket.
Chapter 2 Installing the Access Point Mounting the Access Point REVIEW DRAFT Figure 2-10 Exploded View of the Pivoting Mounting Kit 1 2 3 4 5 1 90.0 mm M8 screw 2 M8 washer 3 M8 spring washer 4 M8 nut 5 80.
Chapter 2 Installing the Access Point Mounting the Access Point REVIEW DRAFT Materials Required In Kit Crimping tool for ground lug, Panduit CT0720 with CD-720-1 die (http://onlinecatalog.paduit.
Chapter 2 Installing the Access Point Mounting the Access Point REVIEW DRAFT Figure 2-11 AP Pivot Mounted 1 3 2 347853 4 1 2 Pole Metal Band Mounting Straps. For the kit which uses a clamp instead of metal bands, see Figure 2-9.
Chapter 2 Installing the Access Point Mounting the Access Point REVIEW DRAFT Materials Required In Kit Drill bit for wall anchors No Electric drill and standard screwdriver No #6 AWG ground wire No Shielded outdoor-rated Ethernet (CAT5e or better) cable No Grounding block No Grounding rod No 13-mm box-end wrench or socket set No 10-mm box-end wrench No Step 1 Mount the pivot bracket to a wall or a pole as shown in the previous procedures.
Chapter 2 Installing the Access Point Mounting the Access Point REVIEW DRAFT Figure 2-12 Access Point Horizontally Mounted using the Optional Horizontal Mount Plate Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide 2-24 OL-30864-01
Chapter 2 Installing the Access Point Mounting the Access Point REVIEW DRAFT Figure 2-13 Exploded View of a Horizontally Mounted Access Point 1 3 4 2 1 Pivoting bracket. Can be mounted on a pole or 2 a wall.
Chapter 2 Installing the Access Point Installing AP Cover or Solar Shield (AIR-ACC1530-CVR=) REVIEW DRAFT Installing AP Cover or Solar Shield (AIR-ACC1530-CVR=) You can install an optional solar shield AIR-ACC1530-CVR= to cover the AP. Note The cover can be installed prior to or after all connections are made. The only exception is when remote cabled antennas are installed – in such cases, the shield must be installed before the antenna cables are attached to the AP.
Chapter 2 Installing the Access Point Installing Antennas REVIEW DRAFT Installing Antennas Table 2-6 shows the antennas supported by the 1532 access point and provides required quantities for each model. Table 2-6 1532 Access Point Supported External Antennas Product ID Frequency Band Gain Type AIR-ANT2547VG-N 2.4 / 5 GHz 4 / 7 dBi Omnidirectional AIR-ANT2588P3M-N= 2.4 / 5 GHz 4 / 7 dBi Omnidirectional AIR-ANT2588P3M-N 2.4 / 5 GHz 8 / 8 dBi Directional AIR-ANT2450V-N 2.
Chapter 2 Installing the Access Point Installing Antennas REVIEW DRAFT 4. Plan your installation carefully and completely before you begin. Each person involved in an installation should be assigned to a specific task and should know what to do and when to do it. One person should be in charge of the operation to issue instructions and watch for signs of trouble. 5. When installing your antenna, follow these guidelines: – Do not use a metal ladder. – Do not work on a wet or windy day.
Chapter 2 Installing the Access Point Installing Antennas REVIEW DRAFT – 5250–5875 MHz — 7-dBi The antenna is designed to create an omnidirectional broadcast pattern. To achieve this pattern, mount the access point clear of any obstructions to the sides of the radiating element. For detailed information on this antenna, refer to the Cisco Aironet Dual-Band Omnidirectional Antenna (AIR-ANT2547V-N, AIR-ANT2547VG-N) document. Follow all safety precautions when installing the antennas.
Chapter 2 Installing the Access Point Installing Antennas REVIEW DRAFT Cisco Aironet 2.4-GHz/5-GHz 8-dBi Directional Antenna (AIR-ANT2588P3M-N) The Cisco Aironet 2.4-GHz/5-GHz 8-dBi Directional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in both the 2.4-GHz and 5-GHz frequency bands. This antenna has 8-dBi gain in both bands. For detailed information on this antenna, refer to the Cisco Aironet 2.
Chapter 2 Installing the Access Point Installing Antennas REVIEW DRAFT Cisco Aironet 5-GHz 14-dBi 2-Port Directional Antenna (AIR-ANT5114P2M-N) The Cisco Aironet 5-GHz 14-dBi 2-Port Directional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 5-GHz frequency band. This antenna has 14-dBi in the 5-GHz band.
Chapter 2 Installing the Access Point Installing Antennas REVIEW DRAFT Cisco Aironet 2.4-GHz 13-dBi 2-Port Directional Antenna (AIR-ANT2413P2M-N) The Cisco Aironet 2.4-GHz 13-dBi 2-Port Directional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz frequency band. This antenna has 13-dBi gain in the 2.4-GHz frequency band. For detailed information on this antenna, refer to the Cisco Aironet 2.
Chapter 2 Installing the Access Point Installing Antennas REVIEW DRAFT Cisco Aironet 2.4-GHz 5-dBi Omnidirectional Antenna (AIR-ANT2450V-N) The Cisco Aironet 2.4-GHz 5-dBi Omnidirectional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz frequency band. This antenna has a 5-dBi gain in the 2.4-GHz band. For detailed information on this antenna, refer to the document Cisco Aironet 5-dBI Omnidirectional Antenna (AIR-ANT2450V-N).
Chapter 2 Installing the Access Point Installing Antennas REVIEW DRAFT Cisco Aironet 2.4-GHz 8-dBi Omnidirectional Antenna (AIR-ANT2480V-N) The Cisco Aironet 2.4-GHz 8-dBi Omnidirectional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz frequency band. This antenna has 8-dBi gain in the 2.4-GHz frequency band. For detailed information on this antenna, refer to the document Cisco Aironet 8-dBi Omnidirectional Antenna (AIR-ANT2480V-N).
Chapter 2 Installing the Access Point Installing Antennas REVIEW DRAFT Cisco Aironet 5-GHz 8-dBi Omnidirectional Antenna (AIR-ANT5180V-N) The Cisco Aironet 5-GHz 8-dBi Omnidirectional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 5-GHz frequency band. This antenna has 8-dBi gain in the 5-GHz frequency band. For detailed information on this antenna, refer to the document Cisco Aironet 8-dBi Omnidirectional Antenna (AIR-ANT5180V-N).
Chapter 2 Installing the Access Point Installing Antennas REVIEW DRAFT Antenna N-Type Connector Locations The access point antenna N-type connectors are located on the top and the bottom of model AIR-CAP1532E-x-K9. The N-type connectors support variety of the Cisco Aironet antennas. For detailed information on these antennas, refer to Antenna Configurations, page 2-28. Figure 2-22 shows the antenna port locations viewed from the RF cover side.
Chapter 2 Installing the Access Point Installing Antennas REVIEW DRAFT • Connect the lightning arrestor components directly to the grounding point. • The contact points of the ground connection must be clean and free of dust and moisture. • Tighten threaded contacts to the torque specified by the manufacturer. Installation Notes This lightning arrestor is designed to be installed between the antenna cable that is attached to an outdoor antenna and the Cisco Aironet wireless device.
Chapter 2 Installing the Access Point Grounding the Access Point REVIEW DRAFT Cable for the Lightning Arrestor Coaxial cable loses efficiency as the frequency increases, resulting in signal loss. The cable should be kept as short as possible because cable length also determines the amount of signal loss (the longer the run, the greater the loss). Cisco recommends a high-quality, low-loss cable for use with the lightning arrestor.
Chapter 2 Installing the Access Point Powering the Access Point REVIEW DRAFT Warning This equipment must be externally grounded using a customer-supplied ground wire before power is applied. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 366 Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.
Chapter 2 Installing the Access Point Powering the Access Point REVIEW DRAFT Warning Connect the unit only to DC power source that complies with the Safety Extra-Low Voltage (SELV) requirements in IEC 60950 based safety standards Statement 1033 Connecting a 1530 Series Power Injector The 1530 Series Access Points support the following power injectors: • AIR-PWRINJ1500-2= — 100-240 VAC input, indoor use only • AIR-PWRINJ4= — 100-240 VAC input, indoor use only The power injector provides (AIR-PWRINJ
Chapter 2 Installing the Access Point Powering the Access Point REVIEW DRAFT Connecting an Ethernet Cable to the Access Point You need to supply these tools and materials: • Shielded outdoor-rated Ethernet (CAT5e or better) cable with 0.2 to 0.35 in. (0.51 to 0.
Chapter 2 Installing the Access Point Powering the Access Point REVIEW DRAFT Note Warning Verify that the cable gland has a rubber seal and ensure that it is not damaged. Failure to install the cable gland and rubber gasket properly will cause the cable grip to leak.
Chapter 2 Installing the Access Point Powering the Access Point REVIEW DRAFT Inserting RJ-45 Connector into the Ethernet Port Opening in Case 352056 Figure 2-26 1 2 3 1 Ethernet port opening in access point case. 2 3 Exploded view of the cable gland,on the Ethernet cable.
Chapter 2 Installing the Access Point Powering the Access Point REVIEW DRAFT Warning Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV) requirements in IEC 60950 based safety standards. Statement 1033 To connect a DC power cable, you need to supply these tools and material: • Shielded outdoor-rated DC power cable (minimum 18 AWG) with outside cable diameter of 0.20 to 0.35 inch (0.51 to 0.89 cm).
Chapter 2 Installing the Access Point Powering the Access Point REVIEW DRAFT Step 4 Loosen the thread-Lock sealing nut of the cable gland by turning it counter clockwise, but do not remove (see Figure 2-28). Note Warning Verify that the cable gland has a rubber seal and ensure that it is not damaged. Failure to install the Cable Gland properly will cause the cable grip to leak.
Chapter 2 Installing the Access Point Powering the Access Point REVIEW DRAFT Figure 2-29 Step 8 Two-Position Terminal Strip 1 Securing screws 2 Wire opening for ground (DC return) 3 Wire opening for DC + Insert the two-position terminal strip into the DC power opening in the access point case, and carefully push the terminal strip into the internal connector (see Figure 2-30).
Chapter 2 Installing the Access Point Powering the Access Point REVIEW DRAFT Figure 2-30 Inserting the Terminal Strip into the DC Power Opening in the Access Point Case 1 352057 2 1 DC power opening in access point case. Also 2 see Figure 2-31.
Chapter 2 Installing the Access Point Powering the Access Point REVIEW DRAFT Connecting Streetlight AC Power The access point can be installed on a streetlight pole and powered from a streetlight outdoor light control using the optional streetlight power tap adapter and AC/DC power adapter, AIR-PWRADPT-1530=. The AC/DC power adapter is used inline from the street light tap to the 1530 DC connector.
Chapter 2 Installing the Access Point Powering the Access Point REVIEW DRAFT Step 3 When using the streetlight power tap adapter (AIR-PWR-ST-LT-R3P=), ensure that the access point is mounted within 3 feet (1 m) of the outdoor light control. Step 4 Ensure that a 6-AWG ground wire is attached to the access point (see Figure 2-32) and connected to the streetlight pole (for instructions see Grounding the Access Point, page 2-38).
Chapter 2 Installing the Access Point Configuring the Access Point REVIEW DRAFT Figure 2-33 Access Point DC Power Connector and Ground Lug (Both AP 1532 Models) 1 2 347846 1 DC power port 2 Ground lug location Step 10 Plug the streetlight power tap adapter into the outdoor light control fixture, as shown in Figure 2-32. Step 11 Plug the outdoor light control into the streetlight power tap adapter.
Chapter 2 Installing the Access Point Configuring the Access Point REVIEW DRAFT Step 7 Repeat Steps 2 to 6 to add other access points to the list. Step 8 Log out of your controller, and close your web browser. Configuring a RAP The access point defaults to the mesh access point (MAP) radio role. One or more of your access points must be reconfigured as a root access point (RAP). The RAPs connect to a wired Ethernet link through a switch to the controller.
Chapter 2 Installing the Access Point Configuring the Access Point REVIEW DRAFT Step 3 Double-click on an access point name. Step 4 Find Mesh Information, and enter the new BGN in the Bridge Group Name field. Step 5 Click Apply. Step 6 Repeat Steps 2 through 5 for each access point. Step 7 Log out from your controller, and close your web browser.
Chapter 2 Installing the Access Point What to Do Next REVIEW DRAFT What to Do Next When you power up a MAP that is not connected to a wired Ethernet, fiber-optic, or cable network to the controller, the access point uses the Cisco Adaptive Wireless Path Protocol (AWPP) to bind to another mesh access point (MAP) with the best path to a root access point (RAP) connected to the wired network to a controller. The access point sends a discovery request when powered up.
Chapter 2 Installing the Access Point What to Do Next REVIEW DRAFT Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide 2-54 OL-30864-01
REVIEW DRAFT CH A P T E R 3 Troubleshooting This chapter provides troubleshooting procedures for basic problems with the access point. For the most up-to-date, detailed troubleshooting information, refer to the Cisco Technical Support and Documentation website at the following URL: http://www.cisco.com/cisco/web/support/index.
Chapter 3 Troubleshooting Guidelines for Using the Access Points REVIEW DRAFT Guidelines for Using the Access Points You should keep these guidelines in mind when you use the access points: • The access point only supports Layer 3 CAPWAP communications with the controllers. In Layer 3 operation, the access point and the controller can be on the same or different subnets. The access point communicates with the controller using standard IP packets.
Chapter 3 Troubleshooting Controller MAC Filter List REVIEW DRAFT Bridge Loop The access point supports packet bridging between wired and wireless network connections. The same network must never be connected to multiple wired ports on an access point or on two bridged access points. A bridge loop causes network routing problems. Controller DHCP Server The controller DHCP server only assigns IP addresses to lightweight access points and wireless clients associated to an access point.
Chapter 3 Troubleshooting Monitoring the Access Point LEDs REVIEW DRAFT Monitoring the Access Point LEDs If your access point is not working properly, look at the LEDs on the bottom of the unit. You can use them to quickly assess the status of the unit. Figure 3-1 shows the location of the access point LEDs. Figure 3-1 Access Point LEDs –Shown on the Bottom of AP 1532E 347848 LED Indicator Note It is expected that there will be small variations in LED color intensity and hue from unit to unit.
Chapter 3 Troubleshooting Monitoring the Access Point LEDs REVIEW DRAFT LED Message Type Color Meaning Boot loader errors Solid Red There has been a DRAM memory test failure Blinking Red and Amber There has been a FLASH file system failure Blinking Red and Off Cisco IOS errors Association status Operating Status Alignment Mode This sequence may indicate any of the following: • Environment variable failure • Bad MAC address • Ethernet failure during image recovery • Boot environment failu
Chapter 3 Troubleshooting Verifying Controller Association REVIEW DRAFT Verifying Controller Association To verify that your access point is associated to the controller, follow these steps: Step 1 Log into your controller web interface using a web browser. You can also use the controller CLI show ap summary command from the controller console port. Step 2 Click Wireless, and verify that your access point MAC address is listed under Ethernet MAC.
Chapter 3 Troubleshooting Changing the Bridge Group Name REVIEW DRAFT Changing the Bridge Group Name The bridge group name (BGN) controls the association of the access points to a RAP. BGNs can be used to logically group the radios to avoid different networks on the same channel from communicating with each other. This setting is also useful if you have more than one RAP in your network in the same area.
Chapter 3 Troubleshooting Access Point Power Injector REVIEW DRAFT Figure 3-2 Power Injector Connectors and LEDs 231484 211485 1 2 3 4 5 6 1 1 Mounting tabs 4 AC POWER LED 2 AP POWER LED 5 TO AP—Ethernet connector (RJ-45) to access point (10/100/1000BASE-T) 3 FAULT LED 6 TO SWITCH—Ethernet connector (RJ-45) to switch (10/100/1000BASE-T) Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide 3-8 OL-30864-01
Chapter 3 Troubleshooting Using the Reset Button REVIEW DRAFT Monitoring the Power Injector LEDs You can use the power injector LEDs to check the power injector status. The LEDs provide the following status information: • AP POWER—Turns solid green after successful discovery; indicates that power injector is supplying power to the access point. • FAULT—Turns solid red when a fault occurs during discovery mode or power-up.
Chapter 3 Troubleshooting Using the Reset Button REVIEW DRAFT Step 1 Using a wrench, remove the hex-shaped plug from the Console-Reset port. Do not to loose the seal around the plug. Step 2 Using a straightened paperclip or a small screwdriver or a pen, push the reset button for less than 10 seconds. This causes the access point to reboot (power cycle). All LEDs turn off for approximately 5 seconds, and then the LEDs will reactivate.
REVIEW DRAFT A P P E N D I X A Translated Safety Warnings For translated safety warnings, refer to the safety warning document that shipped with your access point or that is available on Cisco.com. To browse to the document on Cisco.com, follow these steps: Step 1 Click this link and go to the Cisco Wireless documentation home page: http://www.cisco.com/en/US/products/hw/wireless/index.html Step 2 Click Support and the Support and Documentation page displays.
Appendix A Translated Safety Warnings REVIEW DRAFT Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide A-2 OL-30864-01
REVIEW DRAFT A P P E N D I X B Declarations of Conformity and Regulatory Information This appendix provides declarations of conformity and regulatory information for the Cisco Aironet 1532 Outdoor Access Point.
Appendix B Manufacturers Federal Communication Commission Declaration of Conformity Statement Declarations of Conformity and Regulatory Information REVIEW DRAFT Manufacturers Federal Communication Commission Declaration of Conformity Statement Tested To Comply With FCC Standards FOR HOME OR OFFICE USE Models: FCC Certification number: AIR-CAP1532E-A-K9 LDK102074P AIR-CAP1532EU-A-K9 AIR-CAP1532C-A-K9 AIR-CAP1532CU-A-K9 AIR-CAP1532I-A-K9 Manufacturer: Cisco Systems, Inc.
Appendix B Declarations of Conformity and Regulatory Information Industry Canada REVIEW DRAFT Caution To meet regulatory restrictions, the access point must be professionally installed. Industry Canada Models: IC Certification Number: AIR-CAP1532E-A-K9 2461B-102074P AIR-CAP1532I-A-K9 Canadian Compliance Statement This Class A Digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.
Appendix B Declarations of Conformity and Regulatory Information European Community, Switzerland, Norway, Iceland, and Liechtenstein REVIEW DRAFT European Community, Switzerland, Norway, Iceland, and Liechtenstein Access Point Models: AIR-CAP1532E-E-K9 AIR-CAP1532EU-E-K9 AIR-CAP1532C-E-K9 AIR-CAP1532CU-E-K9 AIR-CAP1532I-E-K9 Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC This declaration is only valid for configurations (combinations of software, fi
Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC REVIEW DRAFT Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide OL-30864-01 B-5
Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC REVIEW DRAFT The following standards were applied: EMC—EN 301.489-1 v1.8.1; EN 301.489-17 v2.1.1 Health & Safety—EN60950-1: 2005; EN 50385: 2002 Radio—EN 300 328 v 1.7.1; EN 301.893 v 1.5.1 The conformity assessment procedure referred to in Article 10.4 and Annex III of Directive 1999/5/EC has been followed.
Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity for RF Exposure REVIEW DRAFT Declaration of Conformity for RF Exposure The following is the declaration of conformity for RF exposure for the United States, Canada, European Union and Australia. United States This system has been evaluated for RF exposure for Humans in reference to ANSI C 95.1 (American National Standards Institute) limits. The evaluation was based on ANSI C 95.1 and FCC OET Bulletin 65C rev 01.
Appendix B Declarations of Conformity and Regulatory Information Guidelines for Operating Cisco Aironet Access Points in Japan REVIEW DRAFT Guidelines for Operating Cisco Aironet Access Points in Japan This section provides guidelines for avoiding interference when operating Cisco Aironet access points in Japan. These guidelines are provided in both Japanese and English.
Appendix B Declarations of Conformity and Regulatory Information Administrative Rules for Cisco Aironet Access Points in Taiwan REVIEW DRAFT VCCI Statement for Japan Warning This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.
Appendix B Declarations of Conformity and Regulatory Information Administrative Rules for Cisco Aironet Access Points in Taiwan REVIEW DRAFT English Translation Administrative Rules for Low-power Radio-Frequency Devices Article 12 For those low-power radio-frequency devices that have already received a type-approval, companies, business units or users should not change its frequencies, increase its power or change its original features and functions.
Appendix B Declarations of Conformity and Regulatory Information Operation of Cisco Aironet Access Points in Brazil REVIEW DRAFT 4.7.7 Manufacturers of U-NII devices are responsible for ensuring frequency stability such that an emission is maintained within the band of operation under all conditions of normal operation as specified in the user manual.
Appendix B Declarations of Conformity and Regulatory Information Operation of Cisco Aironet Access Points in Brazil REVIEW DRAFT Regulatory Information Figure 1 contains Brazil regulatory information for the access point models identified in the previous section.
REVIEW DRAFT A P P E N D I X C Channels and Power Levels For channel and maximum power level settings, refer to the Channels and Maximum Power Settings for Cisco Aironet Lightweight Access Points and Bridges document available on the Cisco Wireless documentation page of Cisco.com. To browse to the document, follow these steps: Step 1 Click this link and go to the Cisco Wireless documentation home page: http://www.cisco.com/en/US/products/hw/wireless/index.html Step 2 Click Support.
Appendix C Channels and Power Levels REVIEW DRAFT Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide C-2 OL-30864-01
REVIEW DRAFT A P P E N D I X D Access Point Data Sheet The detailed technical specifications for the Cisco Aironet 1530 Series Outdoor Access Points are available at the following URL: http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps12831/data_sheet_c78-728356.html You can also download a copy of the Cisco Aironet 1530 Series Outdoor Access Point Data Sheet from the above URL for offline use.
Appendix D Access Point Data Sheet REVIEW DRAFT Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide D-2 OL-30864-01
REVIEW DRAFT A P P E N D I X E Access Point Pinouts This appendix describes the pin signals of the access point Ethernet connectors, and the power injector input and output connectors.
Appendix E Access Point Pinouts REVIEW DRAFT Table E-2 Access Point PoE-In Ethernet Connector Pinouts for AIR-POWERINJ1500 Pin Number Signal Name 7 Ethernet signal pair (1000BASE-T) and DC return 8 Shield Chassis ground Table E-3 describes the pin signals for the power injector input connector (To Switch).
REVIEW DRAFT A P P E N D I X F Configuring DHCP Option 43 This appendix describes the steps needed to configure DHCP Option 43 on a DHCP server, such as a Cisco Catalyst 3750 series switch, for use with Cisco Aironet Access Points.
Appendix F Configuring DHCP Option 43 Overview REVIEW DRAFT Overview This section contains a DHCP Option 43 configuration example on a DHCP server for use with Cisco Aironet Access Points. For other DHCP server implementations, consult DHCP server product documentation for configuring DHCP Option 43. In Option 43, use the IP address of the controller management interface. Note DHCP Option 43 is limited to one access point type per DHCP pool.
Appendix F Configuring DHCP Option 43 Configuring Option 43 for 1000, 1500, and 1530 Series Access Points REVIEW DRAFT Configuring Option 43 for 1000, 1500, and 1530 Series Access Points To configure DHCP Option 43 for Cisco 1000, 1500, and 1530 series access points in the embedded Cisco IOS DHCP server, follow these steps: Step 1 Enter configuration mode at the Cisco IOS command line interface (CLI).
Appendix F Configuring DHCP Option 43 Configuring Option 43 for 1100, 1130, 1200, 1240, 1250, 1300, 1520, and 1530 Series Access Points REVIEW DRAFT Configuring Option 43 for 1100, 1130, 1200, 1240, 1250, 1300, 1520, and 1530 Series Access Points To configure DHCP Option 43 for Cisco Aironet 1100, 1130, 1200, 1240, 1250, 1300, 1520, and 1530 series access points in the embedded Cisco IOS DHCP server, follow these steps: Step 1 Enter configuration mode at the Cisco IOS CLI.
REVIEW DRAFT GLOSSARY 802.3af/at The IEEE standard that describes a mechanism for Power over Ethernet (PoE). The standard provides the capability to deliver both power and data over standard Ethernet cabling. 802.11 The IEEE standard that specifies carrier sense media access control and physical layer specifications for 1- and 2-megabit-per-second (Mb/s) wireless LANs operating in the 2.4-GHz band. 802.
Glossary REVIEW DRAFT Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide GL-2 OL-30864-01
Glossary REVIEW DRAFT B beacon A wireless LAN packet that signals the availability and presence of the wireless device. Beacon packets are sent by access points and base stations; however, client radio cards send beacons when operating in computer to computer (Ad Hoc) mode. BOOTP Boot Protocol. A protocol used for the static assignment of IP addresses to devices on the network. BPSK Binary phase shift keying is a modulation technique used by IEEE 802.
Glossary REVIEW DRAFT DFS Dynamic Frequency Selection. In some regulatory domains, 5-GHz radios are required to use DFS to avoid interfering with radar signals. DHCP Dynamic host configuration protocol. A protocol available with many operating systems that automatically issues IP addresses within a specified range to devices on the network. The device retains the assigned address for a specific administrator-defined period.
Glossary REVIEW DRAFT I IEEE Institute of Electrical and Electronic Engineers. A professional society serving electrical engineers through its publications, conferences, and standards development activities. The body responsible for the Ethernet 802.3 and wireless LAN 802.11 specifications. infrastructure The wired Ethernet network. IP address The Internet Protocol (IP) address of a station.
Glossary REVIEW DRAFT O omni-directional This typically refers to a primarily circular antenna radiation pattern. OFDM Orthogonal frequency division multiplex is a modulation technique used by IEEE 802.11a-compliant wireless LANs for transmission at 6, 9, 12, 18, 24, 36, 48, and 54 Mb/s. P packet A basic message unit for communication across a network. A packet usually includes routing information, data, and sometimes error detection information.
Glossary REVIEW DRAFT spread spectrum A radio transmission technology that spreads the user information over a much wider bandwidth than otherwise required in order to gain benefits such as improved interference tolerance and unlicensed operation. SSID Service set identifier (also referred to as Radio Network Name). A unique identifier used to identify a radio network and which stations must use to be able to communicate with each other or to an access point.
Glossary REVIEW DRAFT workstation A computing device with an installed client adapter. WPA Wi-Fi Protected Access is a standards-based, interoperable security enhancement that strongly increases the level of data protection and access control for existing and future wireless LAN systems. It is derived from and will be forward-compatible with the upcoming IEEE 802.11i standard. WPA leverages TKIP (Temporal Key Integrity Protocol) for data protection and 802.1X for authenticated key management.
