User Manual
Table Of Contents
- Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide
- Preface
- Objectives
- Audience
- Organization
- Conventions
- Related Documents
- Finding the Product Serial Number
- Obtaining Documentation, Support, and Security Guidelines
- About the 1532 Access Point
- Hardware Models
- Hardware Features
- Network Deployment Examples
- Unpacking the Access Point
- Tools and Hardware
- Warnings
- Safety Information
- Avoiding Damage to Radios in a Testing Environment
- Installation Guidelines
- Mounting the Access Point
- Installation Options
- Access Point Mounting Orientation
- Wall Mounting the Access Point with the Fixed Mounting Kit
- Pole Mounting the Access Point with the Fixed Mount Kit
- Wall Mounting the Access Point with the Pivoting Mounting Kit
- Pole Mounting the Access Point with the Pivoting Mounting Kit
- Horizontally Mounting the Access Point with Optional Horizontal Mount Plate
- Installing AP Cover or Solar Shield (AIR-ACC1530-CVR=)
- Installing Antennas
- Grounding the Access Point
- Powering the Access Point
- Configuring the Access Point
- What to Do Next
- Guidelines for Using the Access Points
- Important Notes
- Controller MAC Filter List
- Using DHCP Option 43
- Monitoring the Access Point LEDs
- Verifying Controller Association
- Changing the Bridge Group Name
- Access Point Power Injector
- Using the Reset Button
- Manufacturers Federal Communication Commission Declaration of Conformity Statement
- Industry Canada
- Declaration of Conformity for RF Exposure
- European Community, Switzerland, Norway, Iceland, and Liechtenstein
- Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC
- Declaration of Conformity for RF Exposure
- Guidelines for Operating Cisco Aironet Access Points in Japan
- Administrative Rules for Cisco Aironet Access Points in Taiwan
- Operation of Cisco Aironet Access Points in Brazil
- Overview
- Configuring Option 43 for 1000, 1500, and 1530 Series Access Points
- Configuring Option 43 for 1100, 1130, 1200, 1240, 1250, 1300, 1520, and 1530 Series Access Points
REVIEW DRAFT
F-4
Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide
OL-30864-01
Appendix F Configuring DHCP Option 43
Configuring Option 43 for 1100, 1130, 1200, 1240, 1250, 1300, 1520, and 1530 Series Access Points
Configuring Option 43 for 1100, 1130, 1200, 1240, 1250, 1300, 1520,
and 1530 Series Access Points
To configure DHCP Option 43 for Cisco Aironet 1100, 1130, 1200, 1240, 1250, 1300, 1520, and 1530
series access points in the embedded Cisco IOS DHCP server, follow these steps:
Step 1 Enter configuration mode at the Cisco IOS CLI.
Step 2 Create the DHCP pool, including the necessary parameters such as default router and name server. The
commands used to create a DHCP pool are as follows:
ip dhcp pool pool name
network IP Network Netmask
default-router Default router
dns-server DNS Server
Where:
pool name is the name of the DHCP pool, such as AP1530
IP Network is the network IP address where the controller resides, such as 10.0.15.1
Netmask is the subnet mask, such as 255.255.255.0
Default router is the IP address of the default router, such as 10.0.0.1
DNS Server is the IP address of the DNS server, such as 10.0.10.2
Step 3 Add the Option 60 line using the following syntax:
option 60 ascii “VCI string”
For the VCI string, use the value from Table F-1. The quotation marks must be included.
Step 4 Add the Option 43 line using the following syntax:
option 43 hex hex string
The hex string is assembled by concatenating the TLV values shown below:
Type + Length + Val u e
Type is always f1(hex). Length is the number of controller management IP addresses times 4 in hex. Val u e
is the IP address of the controller listed sequentially in hex.
For example, suppose that there are two controllers with management interface IP addresses,
10.126.126.2 and 10.127.127.2. The type is f1(hex). The length is 2 * 4 = 8 = 08 (hex). The IP addresses
translate to 0a7e7e02 and 0a7f7f02. Assembling the string then yields f1080a7e7e020a7f7f02. The
resulting Cisco IOS command added to the DHCP scope is listed below:
option 43 hex f1080a7e7e020a7f7f02