User Manual
Table Of Contents
- Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide
- Preface
- Objectives
- Audience
- Organization
- Conventions
- Related Documents
- Finding the Product Serial Number
- Obtaining Documentation, Support, and Security Guidelines
- About the 1532 Access Point
- Hardware Models
- Hardware Features
- Network Deployment Examples
- Unpacking the Access Point
- Tools and Hardware
- Warnings
- Safety Information
- Avoiding Damage to Radios in a Testing Environment
- Installation Guidelines
- Mounting the Access Point
- Installation Options
- Access Point Mounting Orientation
- Wall Mounting the Access Point with the Fixed Mounting Kit
- Pole Mounting the Access Point with the Fixed Mount Kit
- Wall Mounting the Access Point with the Pivoting Mounting Kit
- Pole Mounting the Access Point with the Pivoting Mounting Kit
- Horizontally Mounting the Access Point with Optional Horizontal Mount Plate
- Installing AP Cover or Solar Shield (AIR-ACC1530-CVR=)
- Installing Antennas
- Grounding the Access Point
- Powering the Access Point
- Configuring the Access Point
- What to Do Next
- Guidelines for Using the Access Points
- Important Notes
- Controller MAC Filter List
- Using DHCP Option 43
- Monitoring the Access Point LEDs
- Verifying Controller Association
- Changing the Bridge Group Name
- Access Point Power Injector
- Using the Reset Button
- Manufacturers Federal Communication Commission Declaration of Conformity Statement
- Industry Canada
- Declaration of Conformity for RF Exposure
- European Community, Switzerland, Norway, Iceland, and Liechtenstein
- Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC
- Declaration of Conformity for RF Exposure
- Guidelines for Operating Cisco Aironet Access Points in Japan
- Administrative Rules for Cisco Aironet Access Points in Taiwan
- Operation of Cisco Aironet Access Points in Brazil
- Overview
- Configuring Option 43 for 1000, 1500, and 1530 Series Access Points
- Configuring Option 43 for 1100, 1130, 1200, 1240, 1250, 1300, 1520, and 1530 Series Access Points
REVIEW DRAFT
2-3
Cisco Aironet 1530 Series Outdoor Access Point Hardware Installation Guide
OL-30864-01
Chapter 2 Installing the Access Point
Warnings
• FIPS kit (AIRLAP-FIPSKIT=)
• Lightning Arrestor kit (AIR-ACC245LA-N=)
Optional Tools and Hardware That You Supply
Tools and materials that are user-supplied are:
• Ground lug crimping tool (Panduit CT-720 with CD-720-1 die)
• 6-AWG copper ground wire
• 10 mm open end or box wrench
• 13 mm box-end wrench or socket set
• Adjustable wrench with opening up to 33 mm and 28 mm socket.
• Large flat or phillips screw driver (for port plugs)
• Small flat screwdriver for DC power connector
• Optional shielded outdoor-rated Ethernet (CAT5e or better) cable with 0.20 to 0.35 in
(0.51 to 0.89 cm) diameter
• Optional Ethernet RJ-45 connector and installation tool
• Optional shielded outdoor-rated DC power cable with 0.20 to 0.35 inch (.0.51 to 0.89 cm) diameter
• Optional ground rod, as required by local regulations
• Optional ladder, power lift, rope, or other tools as required
Warnings
Translated versions of all safety warnings are available in the safety warning document that shipped with
your access point or on Cisco.com. To browse to the document on Cisco.com, refer to Appendix A,
“Translated Safety Warnings” for instructions.
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this device.
Statement 1071
SAVE THESE INSTRUCTIONS
Warning
This equipment is to be installed by trained and qualified personnel, as per these installation
instructions. The installer is responsible for obtaining any required local or national safety
inspections of the structural integrity of the installation by the local authority/inspection department.
Warning
Do not operate the unit near unshielded blasting caps or in an explosive environment unless the
device has been modified to be especially qualified for such use.
Statement 364