Getting Started Guide
Table Of Contents
- 1 About this Guide
- 2 About the Access Point
- 3 Safety Instructions
- 4 Unpacking the AP
- 5 Ports and Connectors on the AP
- 6 Preparing the AP for Installation
- 7 Installation Overview
- 8 Performing a Pre-Installation Configuration
- 9 Mounting and Grounding the Access Point
- 10 Powering the Access Point
- 11 Configuring and Deploying the Access Point
- 12 Checking the Access Point LEDs
- 13 Miscellaneous Usage and Configuration Guidelines
- 14 Related Documentation
- 15 Declarations of Conformity and Regulatory Information
- Manufacturers Federal Communication Commission Declaration of Conformity Statement
- VCCI Statement for Japan
- Guidelines for Operating Cisco Aironet Access Points in Japan
- Statement 371—Power Cable and AC Adapter
- Industry Canada
- Canadian Compliance Statement
- European Community, Switzerland, Norway, Iceland, and Liechtenstein
- Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC
- Declaration of Conformity for RF Exposure
- Generic Discussion on RF Exposure
- This Device Meets International Guidelines for Exposure to Radio Waves
- This Device Meets FCC Guidelines for Exposure to Radio Waves
- This Device Meets the Industry Canada Guidelines for Exposure to Radio Waves
- Cet appareil est conforme aux directives internationales en matière d'exposition aux fréquences radioélectriques
- Additional Information on RF Exposure
- Administrative Rules for Cisco Aironet Access Points in Taiwan
- Operation of Cisco Aironet Access Points in Brazil
- Declaration of Conformity Statements
- 16 Obtaining Documentation and Submitting a Service Request
4
–
BandSelect
–
Integrated Bluetooth LE 4.1 radio for location and asset tracking.
• Real-time Service Extender which extends real-time services such as voice, wireless, video, and
data to remote locations.
• Datagram Transport Layer Security (DTLS) connection between the access point and the
controller.
• The AP supports the following hardware external interfaces:
–
The Aironet OEAP1810 Series comes with three local GigE Ethernet Ports, one uplink GigE
port, and one passive pass-through RJ45 port.
–
One 10/100/1000BASE-T PoE uplink port.
–
RS-232 management console interface through RJ-45
–
Three 10/100/1000BASE-T ports (local Ethernet ports), including one PoE out port
PoE out provides 802.3af when the access point is powered by Cisco local power supply
(AIR-PWR-D=), ~6.5W when powered by 802.3at, and no output when powered by 802.3af.
–
DC power connector
–
One passive pass-through port RJ-45 (back to bottom).
–
Mode button. For information on how to use the Mode button, see “Using the Mode Button”
section on page 24.
–
USB 2.0 port (no software support at this time)
–
One multi-color LED status indicator. See the “Checking the Access Point LEDs” section on
page 22 for information on the colors of the LED status indicator.
–
Three local Gigabit Ethernet ports available to securely connect wired devices to the network.
• Four integrated 2.4 GHz/5 GHz dual-band antennas located near each corner of the 1810WI
access point under the top housing. Peak antenna gain is approximately 3
dBi and 5 dBi in 2.4
GHz and 5 GHz bands respectively.
A full listing of the access point's features and specification are provided in the Cisco Aironet
OEAP1810 Series Access Point Data Sheet, at the following URL:
(URL to be added later)
Access Point Model Numbers and Regulatory Domains
The Cisco Aironet OEAP1810 series access point models have the format AIR-OEAP1810-x-K9. The
‘x’ in the model number is a placeholder for the regulatory domain. For information on supported
regulatory domains, see the following page:
http://www.cisco.com/go/aironet/compliance