GETTING STARTED GUIDE Cisco Aironet 1830 Series Access Points
1 About this Guide 2 About the Access Point 3 Safety Instructions 4 Unpacking the AP 5 Ports and Connectors on the AP 6 Preparing the AP for Installation 7 Installation Overview 8 Performing a Pre-Installation Configuration 9 Mounting and Grounding the Access Point 10 Powering the Access Point 11 Configuring and Deploying the Access Point 12 Checking the Access Point LEDs 13 Miscellaneous Usage and Configuration Guidelines 14 Related Documentation 15 Declarations of Conformity and Regulato
1 About this Guide This guide provides instructions on how to install and configure your Cisco Aironet 1830 Series Access Point. This guide also provides mounting instructions and limited troubleshooting procedures. The 1830 Series Access Point is referred to as the access point, or abbreviated as AP in this document. 2 About the Access Point The Cisco Aironet 1830 series access point is an 802.11 a/b/g/n/ac (Wave 2) access point, with internal antennas only.
Model numbers ending in C are, by default, factory-shipped with a Cisco Mobility Express software image. For more information, see the Cisco Mobility Express User Guide at the following URL: http://www.cisco.com/c/en/us/td/docs/wireless/access_point/mob_exp/1/user_guide/b_ME_User_Guid e.html Access Point Features A full listing of the access point's features and specification are provided in the Cisco Aironet 1830 Series Access Point Data Sheet, at the following URL: http://www.cisco.
– Mode button. For information on how to use the Mode button, see “Using the Mode Button” section on page 23. – USB 2.0 port (No software support at this time) – One multi-color LED status indicator. See the “Checking the Access Point LEDs” section on page 21 for information on the colors of the LED status indicator. – 1 x 10/100/1000 Mbps WAN Ethernet Port (RJ-45), with PoE support. • 1832I model access point has three integrated 2.4 GHz and 5 GHz dual-band antennas.
3 Safety Instructions Translated versions of the following safety warnings are provided in the translated safety warnings document that is shipped with your access point. The translated warnings are also in the Translated Safety Warnings for Cisco Aironet Access Points, which is available on Cisco.com. Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury.
Caution This product and all interconnected equipment must be installed indoors within the same building, including the associated LAN connections as defined by Environment A of the IEEE 802.3af/at Standard. Note The access point is suitable for use in environmental air space in accordance with section 300.22.C of the National Electrical Code and sections 2-128, 12-010(3), and 12-100 of the Canadian Electrical Code, Part 1, C22.1.
5 Ports and Connectors on the AP The 1830 series access points have an LED indicator on the face of the unit, above the Cisco logo, as shown in Figure 1. For information on the LED scheme, see the “Access Point Status LEDs” section on page 21. The ports and connections on the access point are shown in Figure 2. Figure 1 Access Point LED Indicator Position 354089 1 1 8 LED indicator position. For information on the LED scheme, see the “Access Point Status LEDs” section on page 21.
Access Point Ports and Connections 354181 Figure 2 1 1 2 2 3 4 5 6 Security hasp for padlocking AP to mounting 4 bracket USB 2.0 port Mode button 5 PoE-In port (Ethernet Uplink port) 6 48 V DC input power port (No software support at this time) For information on how to use the Mode button, see “Using the Mode Button” section on page 23.
6 Preparing the AP for Installation Before you mount and deploy your access point, we recommend that you perform a site survey (or use the site planning tool) to determine the best location to install your access point. You should have the following information about your wireless network available: • Access point locations. • Access point mounting options: below a suspended ceiling, on a flat horizontal surface, or on a desktop.
8 Performing a Pre-Installation Configuration For a Cisco Mobility Express deployment, see the Cisco Mobility Express User Guide at this URL: http://www.cisco.com/c/en/us/td/docs/wireless/access_point/mob_exp/1/user_guide/b_ME_User_Guid e.html The following procedures ensure that your access point installation and initial operation go as expected. This procedure is optional. Note Performing a pre-installation configuration is an optional procedure.
Figure 3 Pre-Installation Configuration Setup Controller Layer 3 devices 272488 Cisco wireless access points To perform pre-installation configuration, perform the following steps: Step 1 Make sure that the Cisco wireless LAN controller DS port is connected to the network. Use the CLI, web-browser interface, or Cisco Prime Infrastructure procedures as described in the appropriate Cisco wireless LAN controller guide. a.
information. Note Step 2 The access point requires a gigabit Ethernet (GbE) link to prevent the Ethernet port from becoming a bottleneck for traffic because wireless traffic speeds exceed transmit speeds of a 10/100 Ethernet port. Apply power to the access point. See “Powering the Access Point” section on page 16. a. As the access point attempts to connect to the controller, the LEDs cycle through a green, red, and amber sequence, which can take up to 5 minutes.
Note 14 When you are installing a Layer 3 access point on a different subnet than the Cisco wireless LAN controller, be sure that a DHCP server is reachable from the subnet on which you will be installing the access point, and that the subnet has a route back to the Cisco wireless LAN controller. Also be sure that the route back to the Cisco wireless LAN controller has destination UDP ports 5246 and 5247 open for CAPWAP communications.
9 Mounting and Grounding the Access Point Cisco Aironet 1832 series access points can be mounted in several configurations – on a suspended ceiling, on a hard ceiling or wall, on an electrical or network box, and above a suspended ceiling. Detailed instructions on how to mount the access point is available at the following URL: http://www.cisco.com/c/en/us/td/docs/wireless/access_point/mounting/guide/apmount.html The standard mounting hardware supported by the AP is listed in Table 1.
10 Powering the Access Point The AP can be powered using: • 48 V DC power via the 48VDC port, using Cisco Power Adapter AC DC AIR-PWR-C=. Ensure that the power cable is routed through the strain relief retention clips cast into the enclosure. See Figure 4. • Power-over-Ethernet (PoE) from the Ethernet cable, from an external power source such as the Cisco Power Injector AIR-PWRINJ4=.You can also use the AIR-PWRINJ5 Cisco Power Injector but with reduced functionality. • Any 802.3at (25.5 W) or 802.3af (15.
Figure 4 Routing the DC Power Cable 2 3 4 5 353859 1 1 Kensington lock slot 4 2 Power cable routed through the strain relief retention clips 5 3 DC power cable DC power cable plugged into the 48VDC port AP secured using a padlock 17
11 Configuring and Deploying the Access Point This section describes how to connect the access point to a wireless LAN controller. The configuration process takes place on the controller. See the Cisco Wireless LAN Controller Configuration Guide for additional information. For a Cisco Mobility Express deployment, see the Cisco Mobility Express User Guide at the following URL: http://www.cisco.com/c/en/us/td/docs/wireless/access_point/mob_exp/1/user_guide/b_ME_User_Guid e.
Note You cannot edit or query any access point using the controller CLI if the name of the access point contains a space. Note Make sure that the controller is set to the current time. If the controller is set to a time that has already passed, the access point might not join the controller because its certificate may not be valid for that time. Access points must be discovered by a controller before they can become an active part of the network.
Deploying the Access Point on the Wireless Network After you have mounted the access point, follow these steps to deploy it on the wireless network: Step 1 Connect and power up the access point. Step 2 Observe the access point LED (for LED descriptions, see “Checking the Access Point LEDs” section on page 21). a. When you power up the access point, it begins a power-up sequence that you can verify by observing the access point LED.
12 Checking the Access Point LEDs Access Point Status LEDs The location of the access point status LED is shown in Figure 1. Note Regarding LED status colors, it is expected that there will be small variations in color intensity and hue from unit to unit. This is within the normal range of the LED manufacturer’s specifications and is not a defect. The access point status LED indicates various conditions and are described in Table 2.
Table 2 LED Status Indications (continued) Message Type LED State Message Meaning Operating status Blinking amber Software upgrade in progress Cycling through green, red, and amber Discovery/join process in progress Rapidly cycling through red, green, amber, and off. Access point location command invoked from controller web interface.
13 Miscellaneous Usage and Configuration Guidelines Using the Mode Button Using the Mode button (see Figure 2) you can: • Reset the AP to its default factory-shipped configuration. • Clear the AP’s internal storage, including all configuration files and the regulatory domain configuration. To use the mode button, press, and keep pressed, the mode button on the access point during the AP's boot cycle. Wait until the AP's status LED changes to Amber.
Troubleshooting the Access Point to Cisco Controller Join Process Note Ensure that your controller is running the latest Cisco Wireless Controller Software Release as specified in the access point’s data sheet. Access points can fail to join a controller for many reasons: a RADIUS authorization is pending; self-signed certificates are not enabled on the controller; the access point’s and controller’s regulatory domains don’t match, and so on.
• An existing access point running software release 8.0.x.x or later has been reset after clearing the configuration. If any of these conditions are met and the access point has not yet joined a controller, you can also configure a DHCP server to return a syslog server IP address to the access point using option 7 on the server. The access point then starts sending all syslog messages to this IP address.
Configuring DHCP Option 43 You can use DHCP Option 43 to provide a list of controller IP addresses to the access points, enabling them to find and join a controller. The following is a DHCP Option 43 configuration example on a Windows 2003 Enterprise DHCP server for use with Cisco Aironet lightweight access points. For other DHCP server implementations, consult product documentation for configuring DHCP Option 43. In Option 43, you should use the IP address of the controller management interface.
is the subnet mask, such as 255.255.255.0 is the IP address of the default router, such as 10.0.0.1 is the IP address of the DNS server, such as 10.0.10.2 Step 3 Add the option 43 line using the following syntax: option 43 hex The hex string is assembled by concatenating the TLV values shown below: Type + Length + Value Type is always f1(hex). Length is the number of controller management IP addresses times 4 in hex.
15 Declarations of Conformity and Regulatory Information This section provides declarations of conformity and regulatory information for the Cisco Aironet 1830 Series Access Points. You can find additional information at this URL: www.cisco.
equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference. However, there is no guarantee that interference will not occur. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna.
Guidelines for Operating Cisco Aironet Access Points in Japan This section provides guidelines for avoiding interference when operating Cisco Aironet access points in Japan. These guidelines are provided in both Japanese and English.
Statement 371—Power Cable and AC Adapter English Translation When installing the product, please use the provided or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for any other electrical devices than products designated by CISCO.
Industry Canada Access Point Models Certification Numbers AIR-AP1832I-A-K9 2461B-102095 AIR-AP1832I-A-K9C 2461B-102098 AIR-AP1832I-UXK9 AIR-AP1832I-UXK9C Canadian Compliance Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Antenna Type Antenna Gain Antenna Impedance Dual-band Omni 2/4 dBi 50 ohms Dual-band Dipole 2/4 dBi 50 ohms Dual-Band Directional 6/6 dBi 50 ohms Operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. La bande 5 150-5 250 MHz est réservés uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC
The following standards were applied: EMC—EN 301.489-1 v1.9.2; EN 301.489-17 v2.2.1 Health & Safety—EN60950-1: 2006; EN 50385: 2002 Radio—EN 300 328 v 1.8.1; EN 301.893 v 1.7.1 The conformity assessment procedure referred to in Article 10.4 and Annex III of Directive 1999/5/EC has been followed.
This device also conforms to the EMC requirements of the Medical Devices Directive 93/42/EEC. Note This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate Compliance. The product carries the CE Mark: Declaration of Conformity for RF Exposure This section contains information on compliance with guidelines related to RF exposure.
As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator. Separation Distance (for FCC ID: LDK102095) MPE 0.69 mW/cm 2 Distance Limit 20 cm (7.87 inches) 1.
Separation Distance (for FCC ID: LDK102095) MPE 0.69 mW/cm2 Distance Limit 20 cm (7.87 inches) 1.00 mW/cm2 Separation Distance (for FCC ID: LDK102098) MPE 0.58 mW/cm 2 Distance Limit 20 cm (7.87 inches) 1.00 mW/cm2 The US Food and Drug Administration has stated that present scientific information does not indicate the need for any special precautions for the use of wireless devices.
Separation Distance (IC 2461B-102098) Frequency MPE 2.4 GHz 2.23 W/m2 5 GHz 2.68 W/m2 Distance 20 cm (7.87 inches) Limit 5.4 W/m2 9.2 W/m2 Health Canada states that present scientific information does not indicate the need for any special precautions for the use of wireless devices.
Distance d'éloignement (IC 2461B-102098) Fréquence MPE 2.4 GHz 2.23 W/m2 5 GHz 2.68 W/m2 Distance 20 cm (7.87 inches) Limite 5.4 W/m2 9.2 W/m2 Santé Canada affirme que la littérature scientifique actuelle n'indique pas qu'il faille prendre des précautions particulières lors de l'utilisation d'un appareil sans fil.
Chinese Translation 41
English Translation Administrative Rules for Low-power Radio-Frequency Devices Article 12 For those low-power radio-frequency devices that have already received a type-approval, companies, business units or users should not change its frequencies, increase its power or change its original features and functions.
English Translation Low-power Radio-frequency Devices Technical Specifications 4.7 Unlicensed National Information Infrastructure 4.7.5 Within the 5.25-5.35 GHz band, U-NII devices will be restricted to indoor operations to reduce any potential for harmful interference to co-channel MSS operations. 4.7.6 The U-NII devices shall accept any interference from legal communications and shall not interfere the legal communications.
Portuguese Translation Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário. English Translation This equipment operates on a secondary basis and consequently must accept harmful interference, including interference from stations of the same kind. This equipment may not cause harmful interference to systems operating on a primary basis.
