Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide First Published: November 14, 2016 Cisco Systems, Inc. www.cisco.com Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco website at www.cisco.com/go/offices.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
CONTENTS Preface vii Objectives Audience vii vii Organization vii Conventions viii Related Documents xiv Finding the Product Serial Number xv Obtaining Documentation, Support, and Security Guidelines CHAPTER 1 Overview xvi 1-1 About the 1560 Access Point 1-1 Access Point Models 1-2 Regulatory Domains 1-2 Hardware Features 1-3 Ports and Connectors 1-3 Connectors on the Base 1-4 Connectors on the Head 1-6 Connectors on the Sides 1-7 Internal Antenna Models 1-8 AP1562I (Internal Antenna) 1
Contents CHAPTER 2 Installing the Access Point 2-1 Unpacking the Access Point 2-2 Package Contents 2-2 Optional Tools and Hardware From Cisco 2-2 Additional Tools and Hardware Required for Installation Pre-Installation Checks and Installation Guidelines 2-3 Typical Access Point Installation Components 2-5 2-3 Mounting the Access Point 2-6 Choosing a Mounting Kit 2-6 Wall Mounting the Access Point with AIR-ACC1530-PMK1= 2-7 Wall Mounting the Access Point with AIR-ACC1560-PMK1= 2-10 Pole Mounting the A
Contents CHAPTER 3 Troubleshooting 3-1 Guidelines for Using the Access Point Convergence Delays 3-2 Bridge Loop 3-3 Controller DHCP Server 3-3 MAP Data Traffic 3-3 Controller MAC Filter List Using DHCP Option 43 3-2 3-3 3-3 Accessing the Console Port and the Reset Button Resetting the Access Point 3-4 Monitoring the Access Point Status LED Verifying Controller Association Changing the Bridge Group Name APPENDIX A B 3-5 3-8 3-8 Safety Guidelines and Warnings A-1 FCC Safety Compliance Statement
Contents Japanese Translation B-10 English Translation B-10 VCCI Statement for Japan B-11 Administrative Rules for Cisco Aironet Access Points in Taiwan Chinese Translation B-11 English Translation B-12 Chinese Translation B-12 English Translation B-12 Statement 371—Power Cable and AC Adapter B-13 English Translation B-13 EU Declaration of Conformity B-13 Operation of Cisco Aironet Access Points in Brazil Access Point Models B-13 Regulatory Information B-14 Portuguese Translation B-14 English Translation B
Preface This section describes the objectives, audience, organization, and conventions of the Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide. Objectives This publication explains the steps for installing the Cisco Aironet 1560 Series Outdoor Access Points (called the access point or AP in this document). Audience This publication is for the person installing and configuring an access point for the first time.
Chapter Title Description Chapter 3 Troubleshooting Provides basic troubleshooting procedures for the access point. Appendix A Safety Guidelines and Warnings Provides the safety warnings and guidelines that need to be strictly followed during the deployment of the access point. Appendix B Declarations of Conformity and Regulatory Information Describes the regulatory conventions to which the access point conforms and provides guidelines for operating access points in Japan.
Warnings use the following conventions: Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.
Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.
Figyelem Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide xi
Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.
Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide xiii
Related Documents To view all support information for the Cisco Aironet 1560 Series, see: http://www.cisco.com/c/en/us/support/wireless/aironet-1560-series/tsd-products-support-series-home.
Finding the Product Serial Number The access point serial number is on the side of the access point (refer to Figure 1). Figure 1 Location of Serial Number Label on the Left of the AP Serial Number The access point serial number label contains the following information: • Serial number, such as WCN0636279B (11 alphanumeric digits). • Access point MAC address, for example 68BDABF54600 (12 hexadecimal digits). It is located under the serial number.
Obtaining Documentation, Support, and Security Guidelines For information on obtaining documentation and support, providing documentation feedback, security guidelines, and recommended aliases and general Cisco documents, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/c/en/us/td/docs/general/whatsnew/whatsnew.html To view all new wireless documentation, click on Wireless.
CH A P T E R 1 Overview The Cisco Aironet 1560 Series Outdoor Access Point (hereafter called the access point or AP) is a wireless outdoor access point which is designed for use in a variety of network configurations. The access point supports wireless client access, point-to-point bridging, point-to-multipoint bridging, and point-to-multipoint mesh wireless connectivity. About the 1560 Access Point The 1560 access point supports two radios (2.
Chapter 1 Overview Access Point Models Access Point Models The model numbers (or part numbers) and configuration for the Cisco Aironet 1560 Outdoor Access Points are described in Table 1-1. For a detailed description of the declarations of conformity and regulatory information for the 1560 access points refer to Appendix B, “Declarations of Conformity and Regulatory Information.
Chapter 1 Overview Hardware Features Hardware Features This section describes the hardware features of the 1560 access point models. The following hardware features are described in this section: • Ports and Connectors, page 1-3 • Internal Antenna Models, page 1-8 • External Antenna Model, page 1-10 • Power Sources, page 1-11 Ports and Connectors Figure 1-4 and Figure 1-5 show the access point connectors for all models.
Chapter 1 Overview Hardware Features Connectors on the Base Access Point Models AP1562I and AP1562D Base Connectors 1 1 2 3 SFP port If the port is not being used, then do not remove the covering plug. Otherwise, it may lead to water leaking into the access point. 2 354842 Figure 1-1 3 Gigabit Ethernet and PoE-In port If the port is not in use, then the covering plug must be tightened to 12.5 lbf-in torque. Otherwise, it may lead to water leaking into the access point.
Chapter 1 Overview Hardware Features Figure 1-2 Access Point Model AP1562E Base Connectors 2 3 4 5 354843 1 1 Antenna 1 port 4 Status LED 2 Antenna 2 port 5 Gigabit Ethernet/WAN and PoE-In port. If the port is not in use, then the covering plug must be tightened to 12.5 lbf-in torque. Otherwise, it may lead to water leaking into the access point. 3 SFP port If the port is not being used, then do not remove the covering plug. Otherwise, it may lead to water leaking into the access point.
Chapter 1 Hardware Features Connectors on the Head Note Figure 1-3 The AP1562I and AP1562D models do not have any connectors on the head of the AP.
Chapter 1 Overview Hardware Features Connectors on the Sides Figure 1-4 Right Side Connectors on all models 1 41 2 1 2 Console port. The console port is under a covering plug. Inspect the seal of the plug and properly tighten it at the time of installation, and also every time the plug is removed and replaced. Tighten the plug to 12.5 lbf-in. If you do not tighten the plug properly, it will not meet IP67 criteria, and may lead to water leaking into the unit. Reset button.
Chapter 1 Overview Hardware Features Figure 1-5 Left Side Connectors on All Models 1 840 2 1 2 Ground Pad. DC Power-In (covered) (42 V – 57 V). If the port is not in use, then the covering plug must be tightened to 12.5 lbf-in torque. Otherwise, it may lead to water leaking into the access point. Internal Antenna Models AP1562I (Internal Antenna) The AP1562I model has an internal omnidirectional antenna. The 1562I access point 802.11b/g/n radio is used primarily for local access and its 802.
Chapter 1 Overview Hardware Features The 1562I access point is equipped with three integrated dual-band antennas with 7 dBi gain at 2 GHz and 4 dBi gain at 5 GHz. AP1562D (Internal Directional Antenna) The 1562D access point 802.11b/g/n radio is used primarily for local access and its 802.11a/n/ac radio for wireless backhaul in the Mesh. The 2 GHz b/g/n radio operates in 2.4 GHz ISM band. It supports channels 1-11 in the US, 1-13 in Europe, and 1-13 in Japan.
Chapter 1 Overview Hardware Features External Antenna Model Figure 1-6 shows the antenna port locations for model AP1562E. The ports used depend on the optional antennas ordered. For detailed information on these antennas, refer to Installing External Antennas, page 2-30.
Chapter 1 Overview Hardware Features The 2 GHz b/g/n radio operates in 2.4 GHz ISM band. It supports channels 1-11 in the US, 1-13 in Europe, and 1-13 in Japan. It has 2 transmitters with a maximum total output power of 27 dBm for 802.11b/g/n operation. Output power is configurable for 8 levels in 3 dB steps. It has two receivers that enable maximum-ratio combining (MRC). The 5 GHz a/n radio operates in the UNII-1 band (5.15-5.25 GHz), UNII-2 band (5.25 - 5.35 GHz), UNII-2 Extended/ETSI band (5.47 - 5.
Chapter 1 Overview Hardware Features Ethernet (PoE) Ports The access point supports an Ethernet uplink port (PoE-In). The access point Ethernet uplink port uses an RJ-45 connector (with weatherproofing) to link the access point to the 10BASE-T, 100BASE-T or 1000BASE-T network. The Ethernet cable is used to send and receive Ethernet data and to optionally supply inline power from the power injector or a suitably powered switch port.
Chapter 1 Overview Network Deployment Examples Network Deployment Examples The access point is a wireless device designed for wireless client access and point-to-point bridging, point-to-multipoint bridging, and point-to-multipoint mesh wireless connectivity. The access point provides 5-GHz backhaul capability to link with another access point to reach a wired network connection or to provide repeater operations for other access points.
Chapter 1 Overview Network Deployment Examples Wireless client access is supported; however, if bridging between tall buildings, the 2.4-GHz wireless coverage area may be limited and possibly not suitable for direct wireless client access. Figure 1-8 Access Point Point-to-Point Bridging Example 255495 (5 GHz) Point-to-Multipoint Bridging The access points can be used as a RAP to connect multiple remote MAPs with their associated wired networks.
Chapter 1 Overview Network Deployment Examples Point-to-Multipoint Mesh Network The access point is typically deployed in a mesh network configuration. In a typical mesh deployment, one or more RAPs have a wired network connection through a switch to a controller. Other remote MAPs without wired network connections use the backhaul feature to optimally link to a RAP that is connected to the wired network. In the mesh network, the links between the access points are referred to as the backhaul links.
Chapter 1 Overview Network Deployment Examples Layer 3 Network Operation The access points support Layer 3 network operation. Access points and controllers in Layer 3 configurations use IP addresses and UDP packets, which can be routed through large networks. Layer 3 operation is scalable and recommended by Cisco. Figure 1-11 illustrates a typical Layer-3 wireless network configuration containing access points and a controller.
CH A P T E R 2 Installing the Access Point This chapter describes how to install the 1560 access point and its accessories.
Chapter 2 Installing the Access Point Unpacking the Access Point Unpacking the Access Point To unpack the access point, follow these steps: Step 1 Open the shipping container and carefully remove the contents. Step 2 Return all packing materials to the shipping container, and save it. Step 3 Ensure that all items listed in “Package Contents” are included in the shipment. If any item is damaged or missing, notify your authorized Cisco sales representative.
Chapter 2 Installing the Access Point Unpacking the Access Point • FIPS kit (AIRLAP-FIPSKIT=) • Lightning Arrestor kit (AIR-ACC245LA-N=) Additional Tools and Hardware Required for Installation You need to independently procure the following tools and materials which maybe required during various stages of installing the AP: • Ground lug crimping tool (Panduit CT-720 with CD-720-1 die) • 6-AWG copper ground wire • 10 mm open end or box wrench • 13 mm box-end wrench or socket set • 16 mm box-en
Chapter 2 Installing the Access Point Unpacking the Access Point Note To calculate path loss and to determine how far apart to install access points, consult an RF planning expert. Before you begin the installation process, ensure the following: • Perform a site survey. See the “Performing Site Surveys” section on page A-5. • Your network infrastructure devices must be operational and properly configured. • Your controllers are connected to switch trunk ports.
Chapter 2 Installing the Access Point Unpacking the Access Point Typical Access Point Installation Components The access point is designed to be installed in an outdoor environment, such as the exterior roof overhang of a tall building or a streetlight pole. Carefully review Figure 2-1 to become familiar with the system components, connectors, indicators, cables, system interconnection, and grounding.
Chapter 2 Installing the Access Point Mounting the Access Point Mounting the Access Point This section provides instructions for installing your access points. Personnel installing the access point must have a good understanding of wireless access points, bridging techniques, and grounding methods. Choosing a Mounting Kit The 1560 Series Access Point can be wall, pole, or tower mounted. The available mounting kits are provided in the table below.
Chapter 2 Installing the Access Point Mounting the Access Point Wall Mounting the Access Point with AIR-ACC1530-PMK1= The AIR-ACC1530-PMK1= mounting kit contains a mounting bracket for wall mounting or pole mounting. You can use the mounting bracket as a template to mark the positions of the mounting holes for your installation, install the mounting bracket, and then attach the access point to the bracket. Table 2-1 lists the materials needed for this installation.
Chapter 2 Installing the Access Point Mounting the Access Point Note The mounting wall, attaching screws, and wall anchors must be able to support a 50-lb (22.7 kg) static weight. Step 3 Screw an M6 x12 mm bolt into each of the four support bolt holes on the back of the access point. Do not screw the bolt all the way in, but leave a gap of approximately 0.13 inch (3.3 mm).
Chapter 2 Installing the Access Point Mounting the Access Point Figure 2-2 Mounting Bracket for Wall and Pole Mounting 1 3 354865 2 1 One of four keyhole slots for mounting the AP. 2 One of four slots for steel band clamps, used for pole mounting only. Figure 2-3 3 Bracket mount holes for fastening bracket to the wall. You can use bolts of up to 1/4" or 6 mm in diameter.
Chapter 2 Installing the Access Point Mounting the Access Point Wall Mounting the Access Point with AIR-ACC1560-PMK1= The AIR-ACC1560-PMK1= mounting kit contains a mounting bracket, for wall mounting or pole mounting, the access point and the power supply together. You can use the mounting bracket as a template to mark the positions of the mounting holes for your installation, install the mounting bracket, and then attach the access point to the bracket.
Chapter 2 Installing the Access Point Mounting the Access Point Note The mounting wall, attaching screws, and wall anchors must be able to support a 50-lb (22.7 kg) static weight. Step 3 Screw an M6 x12 mm bolt into each of the four support bolt holes on the back of the access point. Do not screw the bolt all the way in, but leave a gap of approximately 0.13 inch (3.3 mm).
Chapter 2 Installing the Access Point Mounting the Access Point Figure 2-4 Mounting Bracket for Wall and Pole Mounting AP with Power Supply 3 3 2 1 [180.3] 7.10 [117.5] 4.63 [63.5] 2.50 1 One of four keyhole slots for mounting the AP. 2 Three of six bracket mount holes for fastening the bracket to a wall. Support bolts of up to 1/4" (6 mm) in diameter. 3 Screw holes for fastening the power supply to the bracket.
Chapter 2 Installing the Access Point Mounting the Access Point Pole Mounting the Access Point with AIR-ACC1530-PMK1= The AIR-ACC1530-PMK1= mounting kit contains a mounting bracket that can be used for both wall mounting and pole mounting. This kit can be used to install the access point on a pole, mast or streetlight. It supports metal, wood or fiberglass poles from 2 to 8 inches in diameter.
Chapter 2 Installing the Access Point Mounting the Access Point Figure 2-5 Step 7 Locate the access point to its final position. Tighten the band clamps with the wrench so that the access point does not slide on the pole. Ensure that the clamps are tight enough to not let the AP move. Step 8 Proceed with installing antennas (only for external antenna models), connecting the data cables, grounding the access point, powering and configuring the access point.
Chapter 2 Installing the Access Point Mounting the Access Point Pole Mounting the Access Point with the AIR-ACC1560-PMK1= Kit The AIR-ACC1560-PMK1= fixed mounting kit contains a mounting bracket, for both wall-mounting and pole-mounting, the access point along with the power supply kit. This mounting kit supports metal, wood or fiberglass poles from 2 to 8 inches in diameter.
Chapter 2 Installing the Access Point Mounting the Access Point Figure 2-6 Step 6 Using a 10mm wrench, tighten the four bolts that connect the access point to the bracket to a torque of 40 lbf-in. Step 7 Mount the power supply to the bracket with four #8-32 screws. Step 8 Locate the access point to its final position. Tighten the band clamps with the wrench. Ensure that the clamps are tight enough to not let the AP move. Step 9 Continue with the Grounding the Access Point, page 2-42.
Chapter 2 Installing the Access Point Mounting the Access Point Wall Mounting the AP using AIR-ACC1530-PMK2= Pivoting Mounting Kit The optional pivoting mounting kit AIR-ACC1530-PMK2= contains a pivoting mounting bracket for both wall and pole mounting. This kit allows for adjusting the position of the AP by pivoting the AP along its vertical plane.
Chapter 2 Installing the Access Point Mounting the Access Point Step 3 Use four screws and, if required, wall anchors to attach the wall-plate end of the mounting bracket to the mounting surface. These screws and anchors are to be sourced independently. Note You can use an exterior-grade plywood backboard to mount the access point to stucco, cement, or drywall. Note The mounting wall, attaching screws, and wall anchors must be able to support a 50-lb (22.7 kg) static weight.
Chapter 2 Installing the Access Point Mounting the Access Point Pivoting Mounting Bracket 354866 Figure 2-7 1 One of four bolt holes for fastening to the back of the AP. This is the AP-plate end of the bracket, and is fastened to the back of the AP. 2 3 Screw holes for wall mounting. These screw holes can also be used as slots for steel band clamps in pole-mount installations. Wall-plate end of the bracket. This plate is fastened to the wall. Figure 2-8 Pivoting Mounting Bracket Dimensions 4X 6.
Chapter 2 Installing the Access Point Mounting the Access Point Figure 2-9 Exploded View of the Pivoting Mounting Kit 1 3 4 354868 2 5 1 90.0 mm M8 screw 4 M8 nut 2 M8 washer 5 80.0 mm M8 screw with washer and spring washer, for fastening the pole-mount screw clamp to the pivoting bracket base plate.
Chapter 2 Installing the Access Point Mounting the Access Point Visualization of AP Fastened to the Pivoting Mounting Kit 354861 Figure 2-10 Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide 2-21
Chapter 2 Installing the Access Point Mounting the Access Point Pole Mounting the AP using AIR-ACC1530-PMK2= Pivoting Mounting Kit The optional pivoting mounting kit AIR-ACC1530-PMK2= contains a pivoting mounting bracket for both wall and pole mounting. This kit can be used to install the access point on a pole, mast, or streetlight. It supports metal, wood or fiberglass poles from 2 to 8 inches in diameter.
Chapter 2 Installing the Access Point Mounting the Access Point Step 3 Fasten the pivot bracket base plate to the pole using either one set of the adjustable band clamps or the screw clamp (the screw clamp can be used only on poles that are not more than 3 inches in diameter). Step 4 Position the pole clamp bracket on the pole as needed before tightening the steel bands clamps or the screw clamp.
Chapter 2 Installing the Access Point Mounting the Access Point Figure 2-11 Pivoting Mounting Kit with Pole Mount Clamp 1 3 1 One of four mounting holes for the access point. This is the AP-plate end of the bracket, and is fastened to the back of the AP. 2 One of four slots for band clamps. 354867 2 3 Pole mount screw clamp. It can fit poles having a diameter of up to 3 in. (76mm). This is the pivot bracket base plate, and is fastened to the pole.
Chapter 2 Installing the Access Point Mounting the Access Point Figure 2-12 AP Wall Mounted Using the Pivoting Mounting Bracket 1 2 3 354846 4 1 One of four mounting holes for mounting the access point 3 to the bracket. 2 Slots for band clamps. 4 Steel band clamps. Pole.
Chapter 2 Installing the Access Point Mounting the Access Point Horizontally Mounting the Access Point using AIR-ACC1530-PMK2= The AIR-ACC1530-PMK2= pivoting pole mount kit contains a horizontal mount plate that allows the AP to be mounted horizontally, as shown in Figure 2-14. The horizontal mounting provides better omni antenna coverage.
Chapter 2 Installing the Access Point Mounting the Access Point Figure 2-13 Exploded View of the Pivot Bracket Parts with Horizontal Mount Plate 1 3 4 354858 2 1 Pivoting bracket. Can be mounted on a pole or a wall. 3 Two out of four screw holes for mounting the horizontal mounting plate to the pivoting bracket. 2 Horizontal mounting plate. 4 Two out of four screw holes for mounting the access point to the horizontal mounting plate.
Chapter 2 Mounting the Access Point Access Point Horizontally Mounted using the Optional Horizontal Mount Plate 354862 Figure 2-14 Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide 2-28 Installing the Access Point
Chapter 2 Installing the Access Point Installing AP Cover AIR-ACC1560-CVR= Installing AP Cover AIR-ACC1560-CVR= You can install a cover AIR-ACC1560-CVR=, which also acts as a a solar shield. The cover can be installed prior to or after all connections are made. However, if remote cabled antennas are to be installed, the shield must be installed before the antenna cables are attached to the AP. This step applies only to AP1562D models.
Chapter 2 Installing the Access Point Installing External Antennas Figure 2-16 Installing the Cover on the AP 1 354850 2 1 2 Solar Shield Two of four #8-32 screws Installing External Antennas Table 2-8 shows the external antennas supported by the 1562E access point and provides required quantities for each model. Table 2-8 1562E Access Point Supported External Antennas Product ID Frequency Band Gain Type AIR-ANT2547VG-N 2.4 / 5 GHz 4 / 7 dBi Omnidirectional (gray) AIR-ANT2547V-N 2.
Chapter 2 Installing the Access Point Installing External Antennas Table 2-8 1562E Access Point Supported External Antennas Product ID Frequency Band Gain Type AIR-ANT2450V-N 2.4 GHz 5 dBi Omnidirectional AIR-ANT2480V-N 2.4 GHz 8 dBi Omnidirectional AIR-ANT2413P2M-N= 2.
Chapter 2 Installing the Access Point Installing External Antennas Cisco Aironet Dual-Band Omnidirectional Antenna (AIR-ANT2547V-N, AIR-ANT2547VG-N) The Dual-Band Omnidirectional Antenna, referred to as a “stick” antenna, is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz and 5-GHz frequency bands (Figure 2-17). Basic operating features of the antenna are: • Omnidirectional collinear array • Operates in the 2.
Chapter 2 Installing the Access Point Installing External Antennas Figure 2-17 Cisco Aironet Dual-Band Omnidirectional Antenna - Installed Only on Model AIR-AP1562E-x-K9 2 354851 1 1 Antenna connected to antenna port 1(Type-N connector) 2 (TX/RX) Antenna connected to antenna port 2(Type-N connector) (TX/RX) Cisco Aironet 2.4-GHz/5-GHz 8-dBi Directional Antenna (AIR-ANT2588P3M-N) The Cisco Aironet 2.
Chapter 2 Installing the Access Point Installing External Antennas Cisco Aironet 2.4-GHz/5-GHz 8-dBi Directional Antenna - Installed Only on Model AIR-AP1562E-x-K9 334574 Figure 2-18 Note Figure 2-19 When installing the AIR-ANT2588P3M-N with the Cisco Aironet 1560 Series AP, connect the outermost antenna ports (marked ‘1’ in Figure 2-19) to the AP’s dual band antenna ports.
Chapter 2 Installing the Access Point Installing External Antennas Cisco Aironet 5-GHz 14-dBi 2-Port Directional Antenna (AIR-ANT5114P2M-N) The Cisco Aironet 5-GHz 14-dBi 2-Port Directional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 5-GHz frequency band. This antenna has 14-dBi in the 5-GHz band. For more information, see the Cisco Aironet 5-GHz 14-dBi Directional Antenna document, at the following URL: http://www.cisco.
Chapter 2 Installing the Access Point Installing External Antennas Cisco Aironet 2.4-GHz 13-dBi 2-Port Directional Antenna (AIR-ANT2413P2M-N) The Cisco Aironet 2.4-GHz 13-dBi 2-Port Directional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz frequency band. This antenna has 13-dBi gain in the 2.4-GHz frequency band. For detailed information on this antenna, refer to the Cisco Aironet 2.
Chapter 2 Installing the Access Point Installing External Antennas Cisco Aironet 2.4-GHz 5-dBi Omnidirectional Antenna (AIR-ANT2450V-N) The Cisco Aironet 2.4-GHz 5-dBi Omnidirectional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz frequency band. This antenna has a 5-dBi gain in the 2.4-GHz band. For detailed information on this antenna, refer to the document Cisco Aironet 5-dBI Omnidirectional Antenna (AIR-ANT2450V-N).
Chapter 2 Installing the Access Point Installing External Antennas Cisco Aironet 2.4-GHz 8-dBi Omnidirectional Antenna (AIR-ANT2480V-N) The Cisco Aironet 2.4-GHz 8-dBi Omnidirectional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz frequency band. This antenna has 8-dBi gain in the 2.4-GHz frequency band. For detailed information on this antenna, refer to the document Cisco Aironet 8-dBi Omnidirectional Antenna (AIR-ANT2480V-N).
