Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide First Published: August 30, 2016 Cisco Systems, Inc. www.cisco.com Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco website at www.cisco.com/go/offices.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
CONTENTS Preface vii Objectives Audience vii vii Organization vii Conventions viii Related Documents xiv Finding the Product Serial Number xiv Obtaining Documentation, Support, and Security Guidelines CHAPTER 1 Overview xvi 1-1 About the 1560 Access Point Hardware Models 1-2 Regulatory Domains 1-1 1-2 Hardware Features 1-3 Connectors 1-3 1562I/1562D Connectors 1-4 1562I/E/D Connectors 1-7 External Antenna Port Locations on AP1562E Radio Operation 1-9 AP1562I (Internal Antenna) 1-10 AP1
Contents CHAPTER 2 Installing the Access Point 2-1 Unpacking the Access Point 2-2 Package Contents 2-2 Tools and Hardware 2-2 Optional Tools and Hardware 2-2 Optional Tools and Hardware That You Supply Warnings 2-3 2-3 Safety Information 2-4 FCC Safety Compliance Statement Safety Precautions 2-4 2-4 Avoiding Damage to Radios in a Testing Environment 2-6 Installation Guidelines 2-7 Site Surveys 2-7 Before Beginning the Installation 2-8 Becoming Familiar with Access Point Installation Components
Contents Cable for the Lightning Arrestor Grounding the Access Point 2-46 2-46 Powering the Access Point 2-47 Connecting a 1560 Series Power Injector 2-48 Connecting an Ethernet Cable to the Access Point Connecting a DC Power Cable to the Access Point Connecting Streetlight AC Power 2-56 Connecting a Fiber-optic Cable to the AP Configuring the Access Point What to Do Next CHAPTER 3 Troubleshooting 2-49 2-52 2-58 2-62 2-63 3-1 Guidelines for Using the Access Points 3-2 Important Notes 3-2 Conv
Contents Declaration of Conformity for RF Exposure United States B-9 Canada B-9 European Union B-9 Australia B-9 B-9 Guidelines for Operating Cisco Aironet Access Points in Japan Japanese Translation B-10 English Translation B-10 VCCI Statement for Japan B-11 Administrative Rules for Cisco Aironet Access Points in Taiwan Chinese Translation B-11 English Translation B-12 Chinese Translation B-12 English Translation B-12 Statement 371—Power Cable and AC Adapter B-13 English Translation B-13 EU Declaration
Preface This section describes the objectives, audience, organization, and conventions of the Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide. Objectives This publication explains the steps for installing the Cisco Aironet 1560 Series Outdoor Access Points (called the access point in this document). Audience This publication is for the person installing and configuring an access point for the first time.
Chapter Title Description Chapter 3 Troubleshooting Provides basic troubleshooting procedures for the access point. Appendix A Translated Safety Warnings Indicates how to access the document that provides translations of the safety warnings that appear in this publication. Appendix B Declarations of Conformity and Regulatory Information Describes the regulatory conventions to which the access point conforms and provides guidelines for operating access points in Japan.
Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in this manual. Cautions use the following conventions: Caution Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data. Warnings use the following conventions: Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury.
Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents.
¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.
Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.
Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide xiii
Related Documents These documents provide complete information about the access point: • Release Notes for Cisco Wireless LAN Controllers and Lightweight Access Points • Quick Start Guide: Cisco Aironet 1560 Series Outdoor Access Points • Cisco Wireless LAN Controller Configuration Guide Click this link to browse to the Cisco Wireless documentation home page: http://www.cisco.com/en/US/products/hw/wireless/index.
Figure 1 Location of Serial Number Label on the Left of the AP The access point serial number label contains the following information: • Model number, such as AIR-AP1562E-x-K9. • Serial number, such as WCN0636279B (11 alphanumeric digits). • Access point MAC address, for example 68BDABF54600 (12 hexadecimal digits). It is located under the serial number. You need your product serial number when requesting support from the Cisco Technical Assistance Center.
Obtaining Documentation, Support, and Security Guidelines For information on obtaining documentation and support, providing documentation feedback, security guidelines, and recommended aliases and general Cisco documents, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html To view all new wireless documentation, click on Wireless.
CH A P T E R 1 Overview The Cisco Aironet 1560 Series Outdoor Access Point (hereafter called the access point or AP) is a wireless outdoor access point which is designed for use in a variety of network configurations. The access point supports wireless client access, point-to-point bridging, point-to-multipoint bridging, and point-to-multipoint mesh wireless connectivity. About the 1560 Access Point The 1560 access point supports two radios (2.
Chapter 1 Overview Hardware Models Hardware Models The model numbers (or part numbers) and configuration for the Cisco Aironet 1560 Outdoor Access Points are described in Table 1-1. For a detailed description of the declarations of conformity and regulatory information for the 1560 access points refer to Appendix B, “Declarations of Conformity and Regulatory Information.
Chapter 1 Overview Hardware Features Hardware Features This section describes the hardware features of the 1560 access point models. The following hardware features are described in this section: • Connectors, page 1-3 • External Antenna Port Locations on AP1562E, page 1-9 • Multiple Power Sources, page 1-10 • Ethernet (PoE) Ports, page 1-12 • Optional Hardware, page 1-12 Connectors Figure 1-4 and Figure 1-5 show the access point connectors for all models.
Chapter 1 Overview Hardware Features 1562I/1562D Connectors Figure 1-1 1 Access Point Models AP1562I and AP1562D Bottom Connectors SFP port If the port is not being used, then do not remove the covering plug. Otherwise, it may lead to water leaking into the access point. 2 Status LED Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide 1-4 3 Gigabit Ethernet and PoE-In port If the port is not in use, then the covering plug must be tightened to 12.5 lbf-in torque.
Chapter 1 Overview Hardware Features Figure 1-2 Access Point Model AP1562E Bottom Connectors 1 Antenna 1 port 4 Status LED 2 Antenna 2 port 5 Gigabit Ethernet and PoE-In port If the port is not in use, then the covering plug must be tightened to 12.5 lbf-in torque. Otherwise, it may lead to water leaking into the access point. 3 SFP port If the port is not being used, then do not remove the covering plug. Otherwise, it may lead to water leaking into the access point.
Chapter 1 Hardware Features Figure 1-3 1 Access Point Model AP1562E Top Connectors Antenna port 4 Note Antenna port 3 The AP1562I and AP1562D models do not have any top connectors.
Chapter 1 Overview Hardware Features 1562I/E/D Connectors Figure 1-4 1 Right Side Connectors on all models Console port. The console port is under a covering plug. Inspect the seal of the plug and properly tighten it at the time of installation, and also every time the plug is removed and replaced. Tighten the plug to 12.5 lbf-in. If you do not tighten the plug properly, it will not meet IP67 criteria, and may lead to water leaking into the unit. 2 Reset button.
Chapter 1 Overview Hardware Features Figure 1-5 1 Left Side Connectors on All Models Ground Pad. 2 DC Power-In (covered). If the port is not in use, then the covering plug must be tightened to 12.5 lbf-in torque. Otherwise, it may lead to water leaking into the access point.
Chapter 1 Overview Hardware Features External Antenna Port Locations on AP1562E Figure 1-6 shows the antenna port locations for model AP1562E. The ports used depend on the optional antennas ordered.
Chapter 1 Overview Hardware Features AP1562E (External Antenna) The 1562E access point is equipped with four N-type RF connectors. The 1562E can be configured via software to support dual band or single band antennas. When configured for dual band antennas, antenna ports 1 and 2 on the bottom of the unit (Figure 1-2) are used to support multiple input/multiple output (MIMO) operation on both 2.4 and 5 GHz radios.
Chapter 1 Overview Hardware Features Caution Do not place the power injector in an unprotected outdoor environment because water could get into the power injector and cause a short circuit and possible fire. Caution When the access point is installed outdoors or in a wet or damp location, the AC branch circuit that is powering the access point should be provided with ground fault protection (GFCI), as required by Article 210 of the National Electrical Code (NEC).
Chapter 1 Overview Hardware Features • External antennas, depending on which ones you purchased (See “AP1562E (External Antenna)” section on page 1-10 for information on available external antennas.) • Wall/Pole mount bracket AIR-ACC1530-PMK1(=) • Wall/Pole mount bracket for AP and AC/DC power adapter AIR-ACC1560-PMK1(=) • Wall/Pole mount bracket with tilt mechanism, spare only AIR-ACC1530-PMK2(=) • Street light power tap (AIR-PWR-ST-LT-R3P=), works only with the AC/DC power adapter.
Chapter 1 Overview Network Deployment Examples Network Deployment Examples The access point is a wireless device designed for wireless client access and point-to-point bridging, point-to-multipoint bridging, and point-to-multipoint mesh wireless connectivity. The access point provides 5-GHz backhaul capability to link with another access point to reach a wired network connection or to provide repeater operations for other access points.
Chapter 1 Overview Network Deployment Examples Wireless client access is supported; however, if bridging between tall buildings, the 2.4-GHz wireless coverage area may be limited and possibly not suitable for direct wireless client access. Figure 1-8 Access Point Point-to-Point Bridging Example 255495 (5 GHz) The access points can also support point-to-point bridging under autonomous mode. In this autonomous mode, the bridging can be done on the 2.4 or 5 GHz radio, but not both.
Overview Network Deployment Examples Figure 1-10 Access Point to Multipoint Bridging Example (5 GHz) 255494 (5 GHz) The access points can also support point-to-multipoint bridging under autonomous mode. In this autonomous mode, the bridging can be done on the 2.4 or 5 GHz radio, but not both. In this mode, one access point is designated as the root and the other end is designated as the non-root bridge. Figure 1-11 Access Point to Multipoint Bridging in Autonomous Mode z z 2.4 GH 2.
Chapter 1 Overview Network Deployment Examples Point-to-Multipoint Mesh Network The access point is typically deployed in a mesh network configuration. In a typical mesh deployment, one or more RAPs have a wired network connection through a switch to a controller. Other remote MAPs without wired network connections use the backhaul feature to optimally link to a RAP that is connected to the wired network. In the mesh network, the links between the access points are referred to as the backhaul links.
Chapter 1 Overview Network Deployment Examples Layer 3 Network Operation The access points support Layer 3 network operation. Access points and controllers in Layer 3 configurations use IP addresses and UDP packets, which can be routed through large networks. Layer 3 operation is scalable and recommended by Cisco. Figure 1-13 illustrates a typical Layer-3 wireless network configuration containing access points and a controller.
Chapter 1 Network Deployment Examples Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide 1-18 Overview
CH A P T E R 2 Installing the Access Point This chapter describes how to install the 1560 access point and contains the following sections: • Unpacking the Access Point, page 2-2 • Tools and Hardware, page 2-2 • Safety Warnings, page 2-4 • Before Beginning the Installation, page 2-8 • Becoming Familiar with Access Point Installation Components, page 2-9 • Mounting the Access Point, page 2-11 • Installing Antennas, page 2-35 • Grounding the Access Point, page 2-48 • Powering the Access Poi
Chapter 2 Installing the Access Point Unpacking the Access Point Unpacking the Access Point To unpack the access point, follow these steps: Step 1 Open the shipping container and carefully remove the contents. Step 2 Return all packing materials to the shipping container, and save it. Step 3 Ensure that all items listed in “Package Contents” are included in the shipment. If any item is damaged or missing, notify your authorized Cisco sales representative.
Chapter 2 Installing the Access Point Tools and Hardware • AC/DC power adapter, spare only AIR-PWRADPT-RGD1= • AIR-PWRINJ-60-PMK= mounting bracket for AIR-PWRADPT-RGD1= • Spare Parts kit containing extra cable glands, power connector, ground lug, etc.
Chapter 2 Installing the Access Point Safety Warnings Safety Warnings Translated versions of all safety warnings are available in the safety warning document that shipped with your access point or on Cisco.com. To browse to the document on Cisco.com, refer to Appendix A, “Translated Safety Warnings” for instructions. Additional safety information, along with regulatory information, is provided in Appendix B, “Declarations of Conformity and Regulatory Information”.
Chapter 2 Installing the Access Point Safety Warnings FCC Safety Compliance Statement The FCC, with its action in ET Docket 96-8, has adopted a safety standard for human exposure to RF electromagnetic energy emitted by FCC-certified equipment. When used with approved Cisco Aironet antennas, Cisco Aironet products meet the uncontrolled environmental limits found in OET-65 and ANSI C95.1, 1991.
Chapter 2 Installing the Access Point Safety Warnings Caution Before connecting or disconnecting a power cord, you must remove power from the power cord using a suitable service disconnect. For safety and to achieve a good installation, please read and follow these safety precautions: • Select your installation site with safety, as well as performance in mind. Remember: electric power lines and phone lines look alike. For safety, assume that any overhead line can kill.
Chapter 2 Installing the Access Point Safety Warnings Where: txpwr = Radio transmit power level tx gain = transmitter antenna gain rx gain = receiver antenna gain For a conducted test bed, the following equation describes the relationships among transmit power, antenna gain, and receiver sensitivity: txpwr - [attenuation due to coaxial components] < max rx input level Caution Under no circumstances should you connect the antenna port from one access point to the antenna port of another access point wit
Chapter 2 Installing the Access Point Before Beginning the Installation Site surveys reveals problems that can be resolved before the network is operational. Because 802.11a/b/g/n operates in an unlicensed spectrum, there may be sources of interference from other 802.11a wireless devices (especially in multi-tenant buildings) that could degrade your 802.11 signals. A site survey can determine if such interference exists at the time of deployment.
Chapter 2 Installing the Access Point Becoming Familiar with Access Point Installation Components • Become familiar with the access point installation components (see the “Becoming Familiar with Access Point Installation Components” section on page 2-9). Becoming Familiar with Access Point Installation Components The access point is designed to be installed in an outdoor environment, such as the exterior roof overhang of a tall building or a streetlight pole.
Chapter 2 Installing the Access Point Becoming Familiar with Access Point Installation Components 1 Building roof-overhang 6 Ground 2 Shielded outdoor-rated Ethernet (CAT5e or better) cable1 7 Power cord 3 Water drip loop 8 Power injector 9 Shielded Ethernet (CAT5e or better) cable1 4 6-AWG copper grounding wire 5 Ground rod1 1 10 Controller (through a switch) 1. User supplied. Warning Installation of the equipment must comply with local and national electrical codes.
Chapter 2 Installing the Access Point Mounting the Access Point Figure 2-3 Streetlight Power Tap Adapter Installation 2 1 3 962 AC/DC Adapter 1 Outdoor light control 2 AC/DC power adapter 3 6-AWG copper grounding wire Mounting the Access Point This section provides instructions for installing your access points. Personnel installing the access point must understand wireless access points and bridging techniques and grounding methods.
Chapter 2 Installing the Access Point Mounting the Access Point Access Point Mounting Orientation When mounting an access point on a horizontal or vertical surface, you must ensure that the access point is oriented with the LED indicators pointing down. This positioning allows LEDs to be visible to someone on the ground below the access point. You must also ensure the access point is mounted in such a way as to ensure that all antenna ports and the console port are accessible for future use.
Chapter 2 Installing the Access Point Mounting the Access Point Wall Mounting the Access Point with AIR-ACC1530-PMK1= Mounting Kit The AIR-ACC1530-PMK1= mounting kit contains a mounting bracket for wall mounting or pole mounting. You can use the mounting bracket as a template to mark the positions of the mounting holes for your installation. You then install the mounting plate, and attach the access point when you are ready.
Chapter 2 Installing the Access Point Mounting the Access Point Figure 2-4 Mounting Bracket for Wall and Pole Mounting 1 347852 2 3 Step 2 Note 1 Quick Mount Keyhole Slots (for AP use) 3 Bracket Mount Holes (use bolts up to 1/4" or 6 mm in diameter) Mounting Slots (used with the band clamps) Use four customer-supplied screws and optional screw-anchors to attach the mounting plate to the mounting surface.
Chapter 2 Installing the Access Point Mounting the Access Point Step 3 Screw an M6 x12 mm bolt into each of the four support bolt holes on the back of the access point. Do not screw the bolt all the way in; leave approximately a 0.13 inch (3.3 mm) space. Step 4 Position the four bolts on the access point into the keyhole slots on the mounting bracket. Step 5 Slide the access point down to sit securely in the quick mount notches.
Chapter 2 Installing the Access Point Mounting the Access Point Wall Mounting the Access Point with AIR-ACC1560-PMK1= Mounting Kit The AIR-ACC1560-PMK1= mounting kit contains a mounting bracket, for wall mounting or pole mounting, the access point and the power supply together. You can use the mounting bracket as a template to mark the positions of the mounting holes for your installation. You then install the mounting plate, and attach the access point when you are ready.
Chapter 2 Installing the Access Point Mounting the Access Point Figure 2-6 Step 2 Note Mounting Bracket for Wall and Pole Mounting 1 Quick Mount Keyhole Slots (for AP use) 3 Screw holes for fastening the power supply to the bracket. 2 3 of 6 bracket mount holes for fastening the bracket to a wall. Use bolts up to 1/4" or 6 mm in diameter. Use four customer-supplied screws and optional screw-anchors to attach the mounting plate to the mounting surface.
Chapter 2 Installing the Access Point Mounting the Access Point Figure 2-7 Mounting Bracket Dimensions Step 3 Screw an M6 x12 mm bolt into each of the four support bolt holes on the back of the access point. Do not screw the bolt all the way in; leave approximately a 0.13 inch (3.3 mm) space. Step 4 Position the four bolts on the access point into the keyhole slots on the mounting bracket. Step 5 Slide the access point down to sit securely in the quick mount notches.
Chapter 2 Installing the Access Point Mounting the Access Point Pole Mounting the Access Point with the AIR-ACC1530-PMK1= Kit The AIR-ACC1530-PMK1= mounting kit contains a mounting bracket for wall mounting or pole mounting.This kit can be used to install the access point on a pole, mast or streetlight. It supports metal, wood or fiberglass poles from 2 to 8 inches in diameter.
Chapter 2 Installing the Access Point Mounting the Access Point Step 6 Using a 10mm wrench, tighten the four bolts that connect the access point to the bracket to a torque of 40 lbf-in. Step 7 Locate the access point to its final position. Tighten the band clamps with the wrench so that the access point does not slide on the pole. Ensure that the clamps are tight enough to not let the AP move. Step 8 Continue with the Grounding the Access Point, page 2-48.
Chapter 2 Installing the Access Point Mounting the Access Point Pole Mounting the Access Point with the AIR-ACC1560-PMK2= Kit The AIR-ACC1560-PMK2= fixed mounting kit contains a mounting bracket, for wall mounting or pole mounting, the access point along with the power supply kit.This mounting kit supports metal, wood or fiberglass poles from 2 to 8 inches in diameter.
Chapter 2 Installing the Access Point Mounting the Access Point Step 6 Using a 10mm wrench, tighten the four bolts that connect the access point to the bracket to a torque of 40 lbf-in. Step 7 Mount the power supply to the bracket with four #8-32 screws. Step 8 Locate the access point to its final position. Tighten the band clamps with the wrench so that the access point does not slide on the pole. Ensure that the clamps are tight enough to not let the AP move.
Chapter 2 Installing the Access Point Mounting the Access Point Wall Mounting the Access Point with the Pivoting Mounting Kit The optional pivoting mounting kit contains a mounting bracket for wall or pole mounting. This kit can be used to install the access point on a wall while still allowing for some freedom of movement. This bracket supports metal, wood or fiberglass surfaces. Figure 2-10 Pivoting Mounting Kit 2 1 351493 3 1 Mounting holes for the AP 3 Wall mount bracket.
Chapter 2 Installing the Access Point Mounting the Access Point Figure 2-11 Pivoting Mounting Kit Dimensions 4X 6.5MM THRU 2x M8 THRU 56 2.20 28 1.10 100 3.94 Table 2-5 [4.0] .16 SLOT WIDTH 352000 17.10 .
Chapter 2 Installing the Access Point Mounting the Access Point Materials Required for mounting AP on a vertical wall with pivoting mounting kit In Kit 13-mm box-end wrench or socket set No 10-mm box-end wrench No Figure 2-12 Caution AP wall mounted with Pivoting Mounting Kit The mounting surface, attaching screws and optional wall anchors must be able to support a 50-lb (22.7 kg) static weight.
Chapter 2 Installing the Access Point Mounting the Access Point Step 6 Using the long bolt and the hardware supplied with the pivoting bracket, bolt the AP and its mounted bracket, on to the bracket mounted on the wall (see Figure 2-14 for an exploded view of this assembly). Step 7 Pivot the AP to your desired position, and then tighten the bolts (using a 13 mm wrench). Step 8 Continue with Grounding the Access Point, page 2-48.
Chapter 2 Installing the Access Point Mounting the Access Point Figure 2-14 Exploded View of the Pivoting Mounting Kit 1 2 3 4 5 1 90.0 mm M8 screw 2 M8 washer 3 M8 spring washer 4 M8 nut 5 80.
Chapter 2 Installing the Access Point Mounting the Access Point Materials Required In Kit Crimping tool for ground lug, Panduit CT0720 with CD-720-1 die (http://www.panduit.
Chapter 2 Installing the Access Point Mounting the Access Point Figure 2-15 AP Pivot Mounted 3 1 4 2 Step 8 1 Bolted Bracket Mounting Holes 2 Mounting Slots 3 Pole 4 Metal Band Mounting Straps. For the kit which uses a clamp instead of metal bands, see Figure 2-13.
Chapter 2 Installing the Access Point Mounting the Access Point Materials Required In Kit Four wall mounting screws (6mm max) No Four wall anchors (specified for all material) No Drill bit for wall anchors No Electric drill and standard screwdriver No #6 AWG ground wire No Shielded outdoor-rated Ethernet (CAT5e or better) cable No Grounding block No Grounding rod No 13-mm box-end wrench or socket set No 10-mm box-end wrench No Step 1 Mount the pivot bracket to a wall or a pole as s
Chapter 2 Installing the Access Point Mounting the Access Point Figure 2-16 Access Point Horizontally Mounted using the Optional Horizontal Mount Plate Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide 2-31
Chapter 2 Installing the Access Point Mounting the Access Point Figure 2-17 Exploded View of the Pivot Bracket Parts 1 3 4 2 1 Pivoting bracket. Can be mounted on a pole or 2 a wall.
Chapter 2 Installing the Access Point Installing AP Cover AIR-ACC1560-CVR= Installing AP Cover AIR-ACC1560-CVR= You can install an AP cover AIR-ACC1560-CVR=, which also acts as a a solar shield. The cover can be installed prior to or after all connections are made. However, if remote cabled antennas are to be installed, the shield must be installed before the antenna cables are attached to the AP. Step 1 This step applies only to AP1562D models.
Chapter 2 Installing the Access Point Installing AP Cover AIR-ACC1560-CVR= Figure 2-19 1 Installing the Cover on the AP Solar Shield Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide 2-34 2 Two of four #8-32 screws
Chapter 2 Installing the Access Point Installing Antennas Installing Antennas Table 2-8 shows the external antennas supported by the 1562E access point and provides required quantities for each model. Table 2-8 1562E Access Point Supported External Antennas Product ID Frequency Band Gain Type AIR-ANT2547VG-N 2.4 / 5 GHz 4 / 7 dBi Omnidirectional (gray) AIR-ANT2547V-N 2.4 / 5 GHz 4 / 7 dBi Omnidirectional (white) AIR-ANT2588P3M-N= 2.4 / 5 GHz 8 / 8 dBi Directional AIR-ANT2450V-N 2.
Chapter 2 Installing the Access Point Installing Antennas 3. Contact your electric power company. Tell them your plans and ask them to come look at your proposed installation. 4. Plan your installation carefully and completely before you begin. Each person involved in an installation should be assigned to a specific task and should know what to do and when to do it. One person should be in charge of the operation to issue instructions and watch for signs of trouble. 5.
Chapter 2 Installing the Access Point Installing Antennas • Gain: – 2400–2483 MHz — 4-dBi – 5250–5875 MHz — 7-dBi The antenna is designed to create an omnidirectional broadcast pattern. To achieve this pattern, mount the access point clear of any obstructions to the sides of the radiating element. For detailed information on this antenna, refer to the Cisco Aironet Dual-Band Omnidirectional Antenna (AIR-ANT2547V-N, AIR-ANT2547VG-N) document. Follow all safety precautions when installing the antennas.
Chapter 2 Installing the Access Point Installing Antennas Cisco Aironet 2.4-GHz/5-GHz 8-dBi Directional Antenna (AIR-ANT2588P3M-N) The Cisco Aironet 2.4-GHz/5-GHz 8-dBi Directional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in both the 2.4-GHz and 5-GHz frequency bands. This antenna has 8-dBi gain in both bands. For detailed information on this antenna, refer to the Cisco Aironet 2.4-GHz/5-GHz 8-dBi Directional Antenna (AIR-ANT2588P3M-N) document.
Installing the Access Point Installing Antennas Figure 2-22 Antenna Ports For Connection to AP’s Dual Band Ports 1 352639 Chapter 2 Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide 2-39
Chapter 2 Installing the Access Point Installing Antennas Cisco Aironet 5-GHz 14-dBi 2-Port Directional Antenna (AIR-ANT5114P2M-N) The Cisco Aironet 5-GHz 14-dBi 2-Port Directional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 5-GHz frequency band. This antenna has 14-dBi in the 5-GHz band. For more information, see the Cisco Aironet 5-GHz 14-dBi Directional Antenna document, at the following URL: http://www.cisco.
Chapter 2 Installing the Access Point Installing Antennas Cisco Aironet 2.4-GHz 13-dBi 2-Port Directional Antenna (AIR-ANT2413P2M-N) The Cisco Aironet 2.4-GHz 13-dBi 2-Port Directional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz frequency band. This antenna has 13-dBi gain in the 2.4-GHz frequency band. For detailed information on this antenna, refer to the Cisco Aironet 2.4-GHz 13-dBi Directional Antenna (AIR-ANT2413P2M-N) document.
Chapter 2 Installing the Access Point Installing Antennas Cisco Aironet 2.4-GHz 5-dBi Omnidirectional Antenna (AIR-ANT2450V-N) The Cisco Aironet 2.4-GHz 5-dBi Omnidirectional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz frequency band. This antenna has a 5-dBi gain in the 2.4-GHz band. For detailed information on this antenna, refer to the document Cisco Aironet 5-dBI Omnidirectional Antenna (AIR-ANT2450V-N).
Chapter 2 Installing the Access Point Installing Antennas Cisco Aironet 2.4-GHz 8-dBi Omnidirectional Antenna (AIR-ANT2480V-N) The Cisco Aironet 2.4-GHz 8-dBi Omnidirectional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz frequency band. This antenna has 8-dBi gain in the 2.4-GHz frequency band. For detailed information on this antenna, refer to the document Cisco Aironet 8-dBi Omnidirectional Antenna (AIR-ANT2480V-N).
Chapter 2 Installing the Access Point Installing Antennas Cisco Aironet 5-GHz 8-dBi Omnidirectional Antenna (AIR-ANT5180V-N) The Cisco Aironet 5-GHz 8-dBi Omnidirectional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 5-GHz frequency band. This antenna has 8-dBi gain in the 5-GHz frequency band. For detailed information on this antenna, refer to the document Cisco Aironet 8-dBi Omnidirectional Antenna (AIR-ANT5180V-N).
Chapter 2 Installing the Access Point Installing Antennas Using a Mounting Bracket for External Directional Antennas You can use the AIR-ACCAMK-2= bracket for mounting a directional antenna directly on the access point. See Figure 2-28. Figure 2-28 Directional Antenna Mounting Bracket AIR-ACCAMK-2= Views 1 Mounting holes for the directional antenna. 2 Note the direction of the arrow. Ensure that the bracket and AP are mounted with the arrow pointing upwards.
Chapter 2 Installing the Access Point Installing Antennas Antenna N-Type Connector Locations The access point antenna N-type connectors are located on the top and the bottom of model AIR-AP1562E-x-K9. The N-type connectors support variety of the Cisco Aironet antennas. For detailed information on these antennas, refer to Antenna Configurations, page 2-36. Figure 2-29 shows the antenna port locations viewed from the RF cover side.
Chapter 2 Installing the Access Point Installing Antennas • Connect the lightning arrestor components directly to the grounding point. • The contact points of the ground connection must be clean and free of dust and moisture. • Tighten threaded contacts to the torque specified by the manufacturer. Installation Notes This lightning arrestor is designed to be installed between the antenna cable that is attached to an outdoor antenna and the Cisco Aironet wireless device.
Chapter 2 Installing the Access Point Grounding the Access Point Cable for the Lightning Arrestor Coaxial cable loses efficiency as the frequency increases, resulting in signal loss. The cable should be kept as short as possible because cable length also determines the amount of signal loss (the longer the run, the greater the loss). Cisco recommends a high-quality, low-loss cable for use with the lightning arrestor. Grounding the Access Point The access point must be grounded before connecting power.
Chapter 2 Installing the Access Point Powering the Access Point Powering the Access Point Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074 Warning This equipment must be externally grounded using a customer-supplied ground wire before power is applied. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.
Chapter 2 Installing the Access Point Powering the Access Point 1. The AIR-PWRINJ6 power injector can only be used in an indoor environment. Therefore the cable from the injector must travel from the protected location to the outside mounted access point.
Chapter 2 Installing the Access Point Powering the Access Point Step 7 Continue with What to Do Next, page 2-66. Connecting an Ethernet Cable to the Access Point You need to supply these tools and materials: • Shielded outdoor-rated Ethernet (CAT5e or better) cable with 0.2 to 0.35 in. (0.51 to 0.
Chapter 2 Installing the Access Point Powering the Access Point Note Step 4 Loosen the Thread-Lock sealing nut of the cable gland by turning it counter clockwise, but do not remove it (see Figure 2-32). Note Warning For information on data cable entry, refer to Figure 1-1 Verify that the cable gland has a rubber seal and ensure that it is not damaged. Failure to install the cable gland and rubber gasket properly will cause the cable grip to leak.
Chapter 2 Installing the Access Point Powering the Access Point Figure 2-33 1 Inserting RJ-45 Connector into the Ethernet Port Opening in Case Ethernet port opening in access point case. 2 RJ-45 connector, on shielded outdoor-rated Ethernet (CAT5e or better) cable (with an exploded view of the cable gland, on the Ethernet cable). Step 8 Slide the cable gland with the rubber seal towards the access point, and screw the threaded end of the body into the access point, and hand-tighten.
Chapter 2 Installing the Access Point Powering the Access Point Connecting a DC Power Cable to the Access Point When powering the access point with DC power, you must ensure that DC power can be conveniently removed from the unit. The power should not be removed by disconnecting the DC power connector on the unit. Warning A readily accessible two-poled disconnect device must be incorporated in the fixed wiring.
Chapter 2 Installing the Access Point Powering the Access Point Figure 2-34 1 Step 4 DC power port 2 Ground lug location Loosen the thread-lock sealing nut of the cable gland by turning it counter clockwise, but do not remove it (see Figure 2-35). Note Warning Access Point DC Power Connector and Ground Lug on the Left of the AP Verify that the cable gland has a rubber seal and ensure that it is not damaged. Failure to install the Cable Gland properly will cause the cable grip to leak.
Chapter 2 Installing the Access Point Powering the Access Point Note The cable gland accepts a cable diameter of 0.20 to 0.35 in. (0.51 to 0.89 cm). Step 5 Insert a bare end of the DC power cable into the rounded end of the cable gland (see Figure 2-35), and pull approximately 6 inches of cable through the adapter. Warning When installing the DC power cable, ensure that cable gland and the rubber gasket are present and installed properly, to avoid water leakage into the enclosure.
Installing the Access Point Powering the Access Point Figure 2-37 Inserting the Terminal Strip into the DC Power Opening in the Access Point Case 1 352057 2 1 DC power opening in access point case. Also 2 see Figure 2-38.
Chapter 2 Installing the Access Point Powering the Access Point Connecting Streetlight AC Power The access point can be installed on a streetlight pole and powered from a streetlight outdoor light control using the optional streetlight power tap adapter and AC/DC power adapter, AIR-PWRADPT-RGD1=. The AC/DC power adapter is used inline from the street light tap to the 1560 DC connector. The AC power tap only can be used with the AC/DC power adapter.
Installing the Access Point Powering the Access Point Step 4 Ensure that a 6-AWG ground wire is attached to the access point (see Figure 2-39) and connected to the streetlight pole (for instructions see Grounding the Access Point, page 2-48).
Chapter 2 Installing the Access Point Connecting a Fiber-optic Cable to the AP Note Step 7 Ensure that your antennas are connected to the access point before you apply power to the access point. Connect the streetlight power tap adapter to the access point AC/DC power adapter. See Connecting a Fiber-optic Cable to the AP.
Chapter 2 Installing the Access Point Connecting a Fiber-optic Cable to the AP You can connect the fiber-optic networking cable to the SFP port (labeled '4' on the base of the AP). The small form-factor pluggable (SFP) transceiver module is used to connect the cable to the SFP port. The SFP port provides both Power-over-Cable and backhaul over fiber options.
Chapter 2 Installing the Access Point Connecting a Fiber-optic Cable to the AP Caution When removing this SFP assembly it is absolutely imperative that you proceed in the reverse order of this installation. Start by loosening the cable gland's nut. Figure 2-42 SC Fiber-optic cable .475" MAX 3.00" MAX 1 1 353684 This end goes into the cable gland 2 SC optic fiber connector Figure 2-43 2 Optic fiber cable Duplex LC Fiber Optic Cable .475" MAX 3.
Chapter 2 Installing the Access Point Connecting a Fiber-optic Cable to the AP Figure 2-44 Exploded View of Connecting Fiber-optic Cable to AP 1 Cable gland 3 Duplex LC Fiber-optic cable 2 SFP module adapter 4 SFP transceiver module Figure 2-45 Fiber-optic Cable Successfully Connected to AP Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide 2-63
Chapter 2 Installing the Access Point Configuring the Access Point Configuring the Access Point For information on configuring the access point, see the following documents: • For Lightweight Access Points and Mesh Access Points, see the Cisco Wireless LAN Controller Configuration Guide, which is available at: (URL to be added at FCS) • For Mesh Access Points, see the Cisco Wireless Mesh Access Points, Design and Deployment Guide, which is available at: (URL to be added at FCS) • For Access Points i
Chapter 2 Installing the Access Point What to Do Next What to Do Next When you power up a MAP that is not connected to a wired Ethernet, fiber-optic, or cable network to the controller, the access point uses the Cisco Adaptive Wireless Path Protocol (AWPP) to bind to another mesh access point (MAP) with the best path to a root access point (RAP) connected to the wired network to a controller. The access point sends a discovery request when powered up.
Chapter 2 What to Do Next Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide 2-66 Installing the Access Point
CH A P T E R 3 Troubleshooting This chapter provides troubleshooting procedures for basic problems with the access point. For the most up-to-date, detailed troubleshooting information, refer to the Cisco Technical Support and Documentation website at the following URL: http://www.cisco.com/cisco/web/support/index.
Chapter 3 Troubleshooting Guidelines for Using the Access Points Guidelines for Using the Access Points You should keep these guidelines in mind when you use the access points: • The access point only supports Layer 3 CAPWAP communications with the controllers. In Layer 3 operation, the access point and the controller can be on the same or different subnets. The access point communicates with the controller using standard IP packets.
Chapter 3 Troubleshooting Controller MAC Filter List Bridge Loop The access point supports packet bridging between wired and wireless network connections. The same network must never be connected to multiple wired ports on an access point or on two bridged access points. A bridge loop causes network routing problems. Controller DHCP Server The controller DHCP server only assigns IP addresses to lightweight access points and wireless clients associated to an access point.
Chapter 3 Troubleshooting Monitoring the Access Point LEDs Monitoring the Access Point LEDs If your access point is not working properly, look at the LEDs on the bottom of the unit. You can use them to quickly assess the status of the unit. Figure 3-1 shows the location of the access point LEDs. Figure 3-1 Note Access Point Status LED It is expected that there will be small variations in LED color intensity and hue from unit to unit.
Chapter 3 Troubleshooting Monitoring the Access Point LEDs LED Message Type Color Meaning Boot loader errors Red There has been a DRAM memory test failure Blinking Red and Amber There has been a FLASH file system failure Blinking Red and Off Cisco IOS errors Association status Operating Status Alignment Mode This sequence may indicate any of the following: • Environment variable failure • Bad MAC address • Ethernet failure during image recovery • Boot environment failure • No Cisco ima
Chapter 3 Troubleshooting Verifying Controller Association Verifying Controller Association To verify that your access point is associated to the controller, follow these steps: Step 1 Log into your controller web interface using a web browser. You can also use the controller CLI show ap summary command from the controller console port. Step 2 Click Wireless, and verify that your access point MAC address is listed under Ethernet MAC. Step 3 Log out of the controller, and close your web browser.
Chapter 3 Troubleshooting Changing the Bridge Group Name Changing the Bridge Group Name The bridge group name (BGN) controls the association of the access points to a RAP. BGNs can be used to logically group the radios to avoid different networks on the same channel from communicating with each other. This setting is also useful if you have more than one RAP in your network in the same area.
Chapter 3 Accessing the Console Port and the Reset Button Figure 3-2 Reset Button Location 1 2 1 Console Port Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide 3-8 2 Reset Button Troubleshooting
Chapter 3 Troubleshooting Accessing the Console Port and the Reset Button Resetting the Access Point Using the Reset button you can either return the AP back to its default factory-shipped configuration or download the latest software image from the default TFTP servers. To use the Reset button: Step 1 Using a wrench, remove the hex-shaped plug from the Console-Reset port. Do not loose the seal around the plug.
Chapter 3 Accessing the Console Port and the Reset Button Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide 3-10 Troubleshooting
A P P E N D I X A Translated Safety Warnings For translated safety warnings, refer to the safety warning document that shipped with your access point or that is available on Cisco.com. To browse to the document on Cisco.com, follow these steps: Step 1 Click this link and go to the Cisco Wireless documentation home page: http://www.cisco.com/en/US/products/hw/wireless/index.html Step 2 Click Support and the Support and Documentation page displays.
Appendix A Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide A-2 Translated Safety Warnings
A P P E N D I X B Declarations of Conformity and Regulatory Information This appendix provides declarations of conformity and regulatory information for the Cisco Aironet 1562 Outdoor Access Point.
Appendix B Manufacturers Federal Communication Commission Declaration of Conformity Statement Declarations of Conformity and Regulatory Information Manufacturers Federal Communication Commission Declaration of Conformity Statement Tested To Comply With FCC Standards FOR HOME OR OFFICE USE Models: FCC Certification number: AIR-AP1562I-B-K9 LDK102104 AIR-AP1562E-B-K9 LKD102103 AIR-AP1562D-B-K9 LDK102104 Manufacturer: Cisco Systems, Inc.
Appendix B Declarations of Conformity and Regulatory Information Industry Canada Caution To meet regulatory restrictions, the access point must be professionally installed. Requirements of operator to register the RLAN device operating Outdoors in the 5150 -5250 MHz band and addressing possible interference issues in this band Section 15.407(j) of the rules established filing requirements for U-NII operators that deploy a collection of more than 1000 outdoor access points with the 5.15-5.
Appendix B Declarations of Conformity and Regulatory Information Industry Canada Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity for RF Exposure Declaration of Conformity for RF Exposure This access point product has been found to be compliant to the requirements set forth in CFR 47 Section 1.1307 addressing RF Exposure from radio frequency devices as defined in Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields.
Appendix B Declarations of Conformity and Regulatory Information European Community, Switzerland, Norway, Iceland, and Liechtenstein European Community, Switzerland, Norway, Iceland, and Liechtenstein Access Point Models: AIR-AP1562I-E-K9 AIR-AP1562E-E-K9 AIR-AP1562D-E-K9 Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC This declaration is only valid for configurations (combinations of software, firmware, and hardware) provided and supported by Cisco S
Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide B-7
Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC The following standards were applied: EMC—EN 301.489-1 v1.8.1; EN 301.489-17 v2.1.1 Health & Safety—EN60950-1: 2005; EN 50385: 2002 Radio—EN 300 328 v 1.7.1; EN 301.893 v 1.5.1 The conformity assessment procedure referred to in Article 10.4 and Annex III of Directive 1999/5/EC has been followed.
Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity for RF Exposure Declaration of Conformity for RF Exposure The following is the declaration of conformity for RF exposure for the United States, Canada, European Union and Australia. United States This system has been evaluated for RF exposure for Humans in reference to ANSI C 95.1 (American National Standards Institute) limits. The evaluation was based on ANSI C 95.1 and FCC OET Bulletin Canada 65C rev 01.01.
Appendix B Declarations of Conformity and Regulatory Information Guidelines for Operating Cisco Aironet Access Points in Japan Guidelines for Operating Cisco Aironet Access Points in Japan This section provides guidelines for avoiding interference when operating Cisco Aironet access points in Japan. These guidelines are provided in both Japanese and English.
Appendix B Declarations of Conformity and Regulatory Information Administrative Rules for Cisco Aironet Access Points in Taiwan VCCI Statement for Japan Warning This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.
Appendix B Declarations of Conformity and Regulatory Information Administrative Rules for Cisco Aironet Access Points in Taiwan English Translation Administrative Rules for Low-power Radio-Frequency Devices Article 12 For those low-power radio-frequency devices that have already received a type-approval, companies, business units or users should not change its frequencies, increase its power or change its original features and functions.
Appendix B Declarations of Conformity and Regulatory Information Operation of Cisco Aironet Access Points in Brazil 4.7.7 Manufacturers of U-NII devices are responsible for ensuring frequency stability such that an emission is maintained within the band of operation under all conditions of normal operation as specified in the user manual.
Appendix B Declarations of Conformity and Regulatory Information Operation of Cisco Aironet Access Points in Brazil Regulatory Information Figure B-1 contains Brazil regulatory information for the access point models identified in the previous section.
A P P E N D I X C Channels and Power Levels For channel and maximum power level settings, refer to the Channels and Maximum Power Settings for Cisco Aironet Lightweight Access Points and Bridges document available on the Cisco Wireless documentation page of Cisco.com. To browse to the document, follow these steps: Step 1 Click this link and go to the Cisco Wireless documentation home page: http://www.cisco.com/en/US/products/hw/wireless/index.html Step 2 Click Support.
Appendix C Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide C-2 Channels and Power Levels
A P P E N D I X D Access Point Data Sheet The detailed technical specifications for the Cisco Aironet 1560 Series Outdoor Access Points are available at the following URL: http://www.cisco.com/c/en/us/products/collateral/wireless/aironet-1560-series/datasheet-c78-737416.h tml You can also download a copy of the Cisco Aironet 1560 Series Outdoor Access Point Data Sheet from the above URL for offline use.
Appendix D Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide D-2 Access Point Data Sheet
A P P E N D I X E Access Point Pinouts This appendix describes the pin signals of the access point Ethernet connectors, and the power injector input and output connectors.
Appendix E Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide E-2 Access Point Pinouts
A P P E N D I X F Configuring DHCP Option 43 For information on how to configure how to use DHCP Option 43 and to see sample configurations for DHCP Option 43 for lightweight Cisco Aironet access points (LAPs), go to the following URL: http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/97066-dhcp-option-43 -00.
Appendix F Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide F-2 Configuring DHCP Option 43
