Installation Guide
Table Of Contents
- Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide
- Preface
- Objectives
- Audience
- Organization
- Conventions
- Related Documents
- Finding the Product Serial Number
- Obtaining Documentation, Support, and Security Guidelines
- About the 1560 Access Point
- Hardware Models
- Hardware Features
- Network Deployment Examples
- Unpacking the Access Point
- Tools and Hardware
- Safety Warnings
- Before Beginning the Installation
- Becoming Familiar with Access Point Installation Components
- Mounting the Access Point
- AP Mounting Options
- Access Point Mounting Orientation
- Wall Mounting the Access Point with AIR-ACC1530-PMK1= Mounting Kit
- Wall Mounting the Access Point with AIR-ACC1560-PMK1= Mounting Kit
- Pole Mounting the Access Point with the AIR-ACC1530-PMK1= Kit
- Pole Mounting the Access Point with the AIR-ACC1560-PMK2= Kit
- Wall Mounting the Access Point with the Pivoting Mounting Kit
- Pole Mounting the Access Point with the Pivoting Mounting Kit
- Horizontally Mounting the Access Point with Optional Horizontal Mount Plate
- Installing AP Cover AIR-ACC1560-CVR=
- Installing Antennas
- Grounding the Access Point
- Powering the Access Point
- Connecting a Fiber-optic Cable to the AP
- Configuring the Access Point
- What to Do Next
- Guidelines for Using the Access Points
- Important Notes
- Controller MAC Filter List
- Using DHCP Option 43
- Monitoring the Access Point LEDs
- Verifying Controller Association
- Changing the Bridge Group Name
- Accessing the Console Port and the Reset Button
- Manufacturers Federal Communication Commission Declaration of Conformity Statement
- Industry Canada
- Declaration of Conformity for RF Exposure
- European Community, Switzerland, Norway, Iceland, and Liechtenstein
- Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC
- Declaration of Conformity for RF Exposure
- Guidelines for Operating Cisco Aironet Access Points in Japan
- Administrative Rules for Cisco Aironet Access Points in Taiwan
- Operation of Cisco Aironet Access Points in Brazil
B-9
Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide
Appendix B Declarations of Conformity and Regulatory Information
Declaration of Conformity for RF Exposure
Declaration of Conformity for RF Exposure
The following is the declaration of conformity for RF exposure for the United States, Canada, European
Union and Australia.
United States
This system has been evaluated for RF exposure for Humans in reference to ANSI C 95.1 (American
National Standards Institute) limits. The evaluation was based on ANSI C 95.1 and FCC OET Bulletin
65C rev 01.01.
AP1562E:To maintain compliance, the minimum separation distance for antennas that have 8 dBi to
14 dBi gain, is 23.6 inches (60 cm) from general bystanders. The minimum separation distance from
antennas that have less than 8 dBi gain to general bystanders is 9.8 inches (25 cm).
AP1562I & AP1562D: To maintain compliance , the minumum seperate distance is 9.8 inches (25cm)
Canada
This system has been evaluated for RF exposure for Humans in reference to ANSI C 95.1 (American
National Standards Institute) limits.
The evaluation was based on RSS-102 Rev 5.
AP1562E:To maintain compliance, the minimum separation distance for antennas that have 8 dBi to 14
dBi gain, is 23.6 inches (60 cm) from general bystanders. The minimum separation distance from
antennas that have less than 8 dBi gain to general bystanders is 11.8 inches (30 cm).
AP1562I & AP1562D: To maintain compliance, the minumum seperate distance is 11.8 inches (30cm)
European Union
This system has been evaluated for RF exposure for Humans in reference to the ICNIRP (International
Commission on Non-Ionizing Radiation Protection) limits. The evaluation was based on the EN 50385
Product Standard to Demonstrate Compliance of Radio Base stations and Fixed Terminals for Wireless
Telecommunications Systems with basic restrictions or reference levels related to Human Exposure to
Radio Frequency Electromagnetic Fields from 300 MHz to 40 GHz. To maintain compliance, the
minimum separation distance for antennas that have 8 dBi to 14 dBi gain, is 23.6 inches (60 cm)
from general bystanders. The minimum separation distance from antennas that have less than 8 dBi
gain to general bystanders is 9.8 inches (25 cm).
Australia
This system has been evaluated for RF exposure for Humans as referenced in the Australian Radiation
Protection standard and has been evaluated to the ICNIRP (International Commission on Non-Ionizing
Radiation Protection) limits. To maintain compliance, the minimum separation distance for antennas
that have 8 dBi to 14 dBi gain, is 23.6 inches (60 cm) from general bystanders. The minimum
separation distance from antennas that have less than 8 dBi gain to general bystanders is 9.8 inches
(25 cm).