Installation Guide
Table Of Contents
- Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide
- Preface
- Objectives
- Audience
- Organization
- Conventions
- Related Documents
- Finding the Product Serial Number
- Obtaining Documentation, Support, and Security Guidelines
- About the 1560 Access Point
- Hardware Models
- Hardware Features
- Network Deployment Examples
- Unpacking the Access Point
- Tools and Hardware
- Safety Warnings
- Before Beginning the Installation
- Becoming Familiar with Access Point Installation Components
- Mounting the Access Point
- AP Mounting Options
- Access Point Mounting Orientation
- Wall Mounting the Access Point with AIR-ACC1530-PMK1= Mounting Kit
- Wall Mounting the Access Point with AIR-ACC1560-PMK1= Mounting Kit
- Pole Mounting the Access Point with the AIR-ACC1530-PMK1= Kit
- Pole Mounting the Access Point with the AIR-ACC1560-PMK2= Kit
- Wall Mounting the Access Point with the Pivoting Mounting Kit
- Pole Mounting the Access Point with the Pivoting Mounting Kit
- Horizontally Mounting the Access Point with Optional Horizontal Mount Plate
- Installing AP Cover AIR-ACC1560-CVR=
- Installing Antennas
- Grounding the Access Point
- Powering the Access Point
- Connecting a Fiber-optic Cable to the AP
- Configuring the Access Point
- What to Do Next
- Guidelines for Using the Access Points
- Important Notes
- Controller MAC Filter List
- Using DHCP Option 43
- Monitoring the Access Point LEDs
- Verifying Controller Association
- Changing the Bridge Group Name
- Accessing the Console Port and the Reset Button
- Manufacturers Federal Communication Commission Declaration of Conformity Statement
- Industry Canada
- Declaration of Conformity for RF Exposure
- European Community, Switzerland, Norway, Iceland, and Liechtenstein
- Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC
- Declaration of Conformity for RF Exposure
- Guidelines for Operating Cisco Aironet Access Points in Japan
- Administrative Rules for Cisco Aironet Access Points in Taiwan
- Operation of Cisco Aironet Access Points in Brazil
2-7
Cisco Aironet 1560 Series Outdoor Access Point Hardware Installation Guide
Chapter 2 Installing the Access Point
Safety Warnings
Where:
txpwr = Radio transmit power level
tx gain = transmitter antenna gain
rx gain = receiver antenna gain
For a conducted test bed, the following equation describes the relationships among transmit power,
antenna gain, and receiver sensitivity:
txpwr - [attenuation due to coaxial components] < max rx input level
Caution Under no circumstances should you connect the antenna port from one access point to the antenna port
of another access point without using an RF attenuator. If you connect antenna ports, you must not
exceed the maximum survivable receive level of 0 dBm. Never exceed 0 dBm, or damage to the access
point can occur. Using attenuators, combiners, and splitters having a total of at least 60 dB of attenuation
ensures that the receiver is not damaged and that PER performance is not degraded.
Installation Guidelines
Because the access point is a radio device, it is susceptible to common causes of interference that can
reduce throughput and range. Follow these basic guidelines to ensure the best possible performance:
• For information on planning and initially configuring your Cisco Mesh network, refer to the Cisco
Wireless Access Points, Design and Deployment Guide, Release 7.3.
• Review the FCC guidelines for installing and operating outdoor wireless LAN devices at
http://www.cisco.com/c/en/us/products/collateral/routers/3200-series-rugged-integrated-services-r
outers-isr/data_sheet_c78-647116.html.
• Perform a site survey before beginning the installation.
• Install the access point in an area where structures, trees, or hills do not obstruct radio signals to and
from the access point.
• The access points can be installed at any height, but best throughput is achieved when all the access
points are mounted at the same height. We recommend installing the access points no higher than
40 feet to allow support for wireless clients on the ground.
• The Console port is under a sealed plugs Inspect the seal of the plug at the time of installation. Every
time the plug is removed or replaced, properly tighten it. Tighten the plug to 15 lbf-in. If you do not
tighten the plug properly, it will not meet IP67 criteria, and may lead to water leaking into the unit.
• If the DC power port, SFP port, or the PoE-In port is not in use, then the port’s covering plug must
be tightened to 12.5 lbf-in torque. Otherwise, it may lead to water leaking into the access point.
Note To calculate path loss and to determine how far apart to install access points, consult an RF planning
expert.
Site Surveys
Every network application is a unique installation. Before installing multiple access points, you should
perform a site survey to determine the optimum use of networking components and to maximize range,
coverage, and network performance.