Quick Start Quick Start Guide for Cisco 1040 Sensor 1 Overview 2 Preparing to Connect Your Cisco 1040 3 Connecting Your Cisco 1040 4 Using Your Cisco 1040 5 Where to Go Next 6 Related Documentation 7 Technical Specifications 8 Regulatory Compliance and Safety Information for Your Cisco 1040 9 Obtaining Documentation 10 Documentation Feedback 11 Cisco Product Security Overview 12 Obtaining Technical Assistance 13 Obtaining Additional Publications and Information
1 Overview This guide is designed to help you quickly set up and use your Cisco 1040 Sensor (Cisco 1040). A Cisco 1040 is a shelf-top unit that connects to the network and obtains Power over Ethernet (PoE) through a Cisco Catalyst switch. It is easy to connect your Cisco 1040.
2 Preparing to Connect Your Cisco 1040 This section describes tasks that you must perform the first time you set up your network to support Cisco 1040 operations. If you have not already completed the following tasks, it is advisable to complete them so that your Cisco 1040 becomes fully operational minutes after you connect it. Install and Configure IP Communications Service Monitor 1.
Configure DHCP Server Option 150 Configure your DHCP server so that option 150 returns the IP address for the TFTP server and provides an IP address, subnet mask, default gateway, and, optionally, a DNS server for a Cisco 1040. If you would like to configure a Cisco router as a DHCP server, see the following URL. http://www.cisco.com/en/US/tech/tk648/tk361/technologies_tech_note09186a0080114aee.shtml (Optional) Configure DNS If you are using DNS in your network, configure DNS entries for Cisco 1040s.
1 10/100-1—Ethernet 10/100 Mbps port, standard RJ45 for connecting to the network and obtaining inline power. 3 Status indicator light—See Understanding the Status Indicator Light, page 8. This port supports IEEE 802.3af standard PoE. Note 2 This port does not support Cisco prestandard PoE. 10/100-2—Ethernet 10/100 Mbps port, standard RJ45 for connecting to a SPAN or Remote SPAN (RSPAN) destination port.
Table 1 Cisco 1040 Port Usage (continued) Protocol Port Number Service Name UDP 69 TFTP—Cisco 1040 uses TFTP to get a configuration file and binary image file. UDP 514 Syslog—Cisco 1040 sends syslog messages to Service Monitor. TCP 2000 SCCP—Cisco 1040 uses SCCP to communicate with Service Monitor.
Connecting the Cisco 1040 to the Cisco Catalyst Switch Before you begin this procedure, see the regulatory compliance and safety information Statement 1001—Work During Lightning Activity, page 26. Step 1 Place the Cisco 1040 on top of the appropriate Cisco Catalyst switch. Note The minimum height necessary to install the Cisco 1040 is 5.08 cm (2 in.). The installation of the unit should not restrict the airflow around the device.
4 Using Your Cisco 1040 After you have successfully connected your Cisco 1040, use Service Monitor to manage and configure it. For example, you will use Service Monitor to specify the binary image filename to use, update configuration files, set the time, and reset Cisco 1040s.
Startup Sequence Number Status Indicator Light Cisco 1040 Condition 3 Yellow solid Registering to a service monitor. Note 4 Green solid or green and flashing If unable to register, the Cisco 1040 returns to startup sequence number 2. Registered to a service monitor: • Green solid—Registered to the primary service monitor. • Green and flashing—Registered to a secondary or tertiary service monitor.
• TFTP IP Address—IP address of the TFTP server from which the Cisco 1040 obtains a configuration file and binary image file. • Software Version—Name of the binary image file installed on the Cisco 1040. • Last Updated—The last time that the configuration for the Cisco 1040 was updated.
5 Where to Go Next After you have performed first time installation tasks and connected a Cisco 1040, Cisco 1040 starts listening to RTP traffic and sending MOS data to Service Monitor. For more information, see the following User Guides for IP Communications Management Suite applications: • User Guide for IP Communications Service Monitor 1.0 • User Guide for IP Communications Operations Manager 1.0 You can access these documents: • In PDF in the Documentation directory on the respective product CD-ROM.
6 Related Documentation Note Although every effort has been made to validate the accuracy of the information in the printed and electronic documentation, you should also review the documentation on Cisco.com for any updates. For information about configuring SPAN and RSPAN ports on Cisco Catalyst switches, see the software configuration guide for the appropriate switch model and Cisco IOS version. Use this procedure to locate software configuration guides for Cisco Catalyst switches.
Table 2 Related Documentation To learn more about... The known product bugs (DDTS) See this document Release Notes for CiscoWorks IP Communications Service Monitor 1.0 In the On the On the In the product product On Cisco online package? CD?1 Cisco.com? Doc. CD? help? No Yes No Yes (PDF, HTML) No Quick Start Guide for IP Communications Service Monitor 1.
7 Technical Specifications These sections describe the technical specifications for Cisco 1040: • Physical and Operating Environment Specifications, page 14 • Cable Specifications, page 15 • Network Port Pinouts, page 15 Physical and Operating Environment Specifications Specification Value or Range Operating temperature 0° to 40°C (32° to 104°F) Operating relative humidity 10% to 90% (non-condensing) Height 3.8 cm (1.5 in.) Width 24.1 cm (9.5 in.) Depth 20.3 cm (8 in.) Weight .5kg (1.0 lb.
Cable Specifications • RJ-45 jack for the LAN 10/100BaseT connection (10/100-1) • RJ-45 jack for the second LAN 10/100BaseT compliant connection (10/100-2) Caution External AC/DC Power Supply Specification: You must use a separately certified AC-to-DC Power Supply. This Power Supply must be rated: 5vDC 2.5A certified and marked: Limited Power Source (or L.P.S.).
8 Regulatory Compliance and Safety Information for Your Cisco 1040 Caution If the Cisco 1040 is used in a manner not specified by Cisco, the protection provided in the equipment might be impaired. Caution Inline power circuits provide current through the communication cable. Use the Cisco-provided cable or a minimum 24 AWG communication cable (for example, CAT 5, 24 AWG). Caution The Cisco 1040 has no operator-serviceable parts inside.
Warning Definition—Statement 1071 Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.
Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents.
Advarsel VIKTIGE SIKKERHETSINSTRUKSJONER Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.
Varning! VIKTIGA SÄKERHETSANVISNINGAR Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.
Translated Warnings This section contains the following warnings translated into multiple languages: • Statement 1004—Installation Instructions, page 25 • Statement 1001—Work During Lightning Activity, page 26 • Statement 1021—SELV Circuit, page 27 • Statement 1074—Comply with Local and National Electrical Codes, page 30 • Statement 1040—Product Disposal, page 31 • Statement 19—TN Power Warning, page 35 • Statement 331—Power Supply Installation Warning, page 36 24
• Statement 1005—Circuit Breaker, page 37 • Statement 1019—Main Disconnecting Device, page 39 Statement 1004—Installation Instructions Warning Waarschuwing Varoitus Read the installation instructions before connecting the system to the power source. Statement 1004 Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit. Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen.
Statement 1001—Work During Lightning Activity Warning Waarschuwing Varoitus Tijdens onweer dat gepaard gaat met bliksem, dient u niet aan het systeem te werken of kabels aan te sluiten of te ontkoppelen. Älä työskentele järjestelmän parissa äläkä yhdistä tai irrota kaapeleita ukkosilmalla. Attention Ne pas travailler sur le système ni brancher ou débrancher les câbles pendant un orage. Warnung Arbeiten Sie nicht am System und schließen Sie keine Kabel an bzw. trennen Sie keine ab, wenn es gewittert.
¡Advertencia! Varning! No operar el sistema ni conectar o desconectar cables durante el transcurso de descargas eléctricas en la atmósfera. Vid åska skall du aldrig utföra arbete på systemet eller ansluta eller koppla loss kablar. Statement 1021—SELV Circuit Warning Waarschuwing To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits.
Varoitus Jotta vältyt sähköiskulta, älä kytke pienjännitteisiä SELV-suojapiirejä puhelinverkkojännitettä (TNV) käyttäviin virtapiireihin. LAN-portit sisältävät SELV-piirejä ja WAN-portit puhelinverkkojännitettä käyttäviä piirejä. Osa sekä LAN- että WAN-porteista käyttää RJ-45-liittimiä. Ole varovainen kytkiessäsi kaapeleita.
¡Advertencia! Para evitar la sacudida eléctrica, no conectar circuitos de seguridad de voltaje muy bajo (safety extra-low voltage = SELV) con circuitos de voltaje de red telefónica (telephone network voltage = TNV). Los puertos de redes de área local (local area network = LAN) contienen circuitos SELV, y los puertos de redes de área extendida (wide area network = WAN) contienen circuitos TNV. En algunos casos, tanto los puertos LAN como los WAN usan conectores RJ-45.
Statement 1074—Comply with Local and National Electrical Codes Warning Waarschuwing Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale elektriciteitsvoorschriften. Varoitus Laitteisto tulee asentaa paikallisten ja kansallisten sähkömääräysten mukaisesti. Attention L'équipement doit être installé conformément aux normes électriques nationales et locales. Warnung Die Installation der Geräte muss den Sicherheitsstandards entsprechen.
Statement 1040—Product Disposal Warning Waarschuwing Varoitus Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 Het uiteindelijke wegruimen van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen. Tämä tuote on hävitettävä kansallisten lakien ja määräysten mukaisesti.
Varning! 32 Vid deponering hanteras produkten enligt gällande lagar och bestämmelser. Aviso O descarte definitivo deste produto deve estar de acordo com todas as leis e regulamentações nacionais. Advarsel Endelig bortskaffelse af dette produkt skal ske i henhold til gældende love og regler.
Statement 353—This Product Must be Connected Warning Waarschuwing Varoitus Attention This product must be connected to a power-over-ethernet (PoE) IEEE 802.3af compliant power source or an IEC60950 compliant limited power source. Statement 353 Dit product moet worden verbonden met een stroomvoorziening die compatibel is met PoE (power-over-ethernet) IEEE 802.3af of een beperkte stroomvoorziening die compatibel is met IEC60950. Tämä tuote on liitettävä PoE (power-over-ethernet) IEEE 802.
Warnung Dieses Produkt muss entweder an eine Stromquelle angeschlossen sein, die mit dem IEEE 802.3af-Standard Power-over-Ethernet (PoE) kompatibel ist oder an eine Stromquelle für geringe Leistungen, die IEC60950-kompatibel ist. Avvertenza Questo prodotto deve essere connesso a una fonte di alimentazione di tipo PoE (power-over-ethernet) conforme a IEEE 802.3af o a una fonte di alimentazione conforme a IEC60950.
When using an AC/DC power supply, the following warnings apply: • Statement 19—TN Power Warning, page 35 • Statement 331—Power Supply Installation Warning, page 36 • Statement 1005—Circuit Breaker, page 37 • Statement 1019—Main Disconnecting Device, page 39 Statement 19—TN Power Warning Warning Waarschuwing Varoitus The device is designed to work with TN power systems. Statement 19 Het apparaat is ontworpen om te functioneren met TN energiesystemen.
Varning! Enheten är konstruerad för användning tillsammans med elkraftssystem av TN-typ. Statement 331—Power Supply Installation Warning Warning Waarschuwing Varoitus De stroomtoevoer moet binnen worden geplaatst. Tehonlähde on sijoitettava sisätiloihin. Attention Le bloc d’alimentation électrique doit être placé à l’intérieur. Warnung Die Stromversorgungsquelle darf nicht im Freien aufgestellt werden. Avvertenza Advarsel Aviso 36 The power supply must be placed indoors.
¡Advertencia! Varning! El suministro de energía debe estar ubicado en un lugar cubierto y no al aire libre. Strömkällan måste vara placerad inomhus. Statement 1005—Circuit Breaker Warning Waarschuwing This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 120 VAC, 15A (U.S.
Warnung Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschlussbzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der Schutzvorrichtung nicht mehr als: 120 VAC, 15A (U.S./CAN); 240 VAC, 10A (INTERNATIONAL) beträgt. Avvertenza Questo prodotto dipende dall'impianto dell'edificio per quanto riguarda la protezione contro cortocircuiti (sovracorrente). Assicurarsi che il dispositivo di protezione non abbia un rating superiore a: 120 VAC, 15A (U.S.
120 VAC, 15A (U.S./CAN); 240 VAC, 10A (INTERNATIONAL) 120 VAC, 15A (U.S./CAN); 240 VAC, 10A (INTERNATIONAL) Statement 1019—Main Disconnecting Device Warning The plug-socket combination must be accessible at all times, because it serves as the main disconnecting device. Statement 1019 Waarschuwing De combinatie van de stekker en het elektrisch contactpunt moet te allen tijde toegankelijk zijn omdat deze het hoofdmechanisme vormt voor verbreking van de aansluiting.
¡Advertencia! Varning! El conjunto de clavija y toma ha de encontrarse siempre accesible ya que hace las veces de dispositivo de desconexión principal. Man måste alltid kunna komma åt stickproppen i uttaget, eftersom denna koppling utgör den huvudsakliga frånkopplingsanordningen.
Deutsch: Dieses Gerät entspricht den wesentlichen Anforderungen und weiteren Bestimmungen der Richtlinien 73/23/EWG und 89/336/EWG mit der Ergänzung durch Richtlinie 93/68/EWG. Español: Este equipo cumple con los requisitos esenciales y otras disposiciones de las Directrices 73/23/EEC y 89/336/EEC de acuerdo a las modificaciones de la Directriz 93/68/EEC.
Suomalainen: Svenska: Tämä laite on direktiivien 73/23/ETY ja 89/336/ETY (kuten muutettu direktiivissä 93/68/ETY) keskeisten vaatimusten ja määräysten mukainen. Denna utrustning uppfyller de väsentliga kraven och andra villkor i direktiven 73/23/EEC och 89/336/EEC enligt ändringarna i direktiv 93/68/EEC. Regulatory Standards Compliance This section includes all regulatory, safety, and electromagnetic compatibility (EMC) standards.
For specific details about the years, revisions and relevant amendments please refer to the applicable declaration of conformity available at http://www.cisco.com. EMC Environmental Conditions for Products Installed in the European Union This section applies to products to be installed in the European Union. The equipment is intended to operate under the following environmental conditions with respect to EMC: • A separate defined location under user’s control.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Class B Notice for Canada This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Statement 295—Class B Warning for Korea Warning This is a Class B Device and is registered for EMC requirements for residential use.
9 Obtaining Documentation Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems. Cisco.com You can access the most current Cisco documentation at this URL: http://www.cisco.com/techsupport You can access the Cisco website at this URL: http://www.cisco.
Nonregistered Cisco.com users can order technical documentation from 8:00 a.m. to 5:00 p.m. (0800 to 1700) PDT by calling 1 866 463-3487 in the United States and Canada, or elsewhere by calling 011 408 519-5055. You can also order documentation by e-mail at tech-doc-store-mkpl@external.cisco.com or by fax at 1 408 519-5001 in the United States and Canada, or elsewhere at 011 408 519-5001.
Reporting Security Problems in Cisco Products Cisco is committed to delivering secure products. We test our products internally before we release them, and we strive to correct all vulnerabilities quickly. If you think that you might have identified a vulnerability in a Cisco product, contact PSIRT: • Emergencies — security-alert@cisco.com An emergency is either a condition in which a system is under active attack or a condition for which a severe and urgent security vulnerability should be reported.
Cisco Technical Support & Documentation Website The Cisco Technical Support & Documentation website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The website is available 24 hours a day, at this URL: http://www.cisco.com/techsupport Access to all tools on the Cisco Technical Support & Documentation website requires a Cisco.com user ID and password.
For a complete list of Cisco TAC contacts, go to this URL: http://www.cisco.com/techsupport/contacts Definitions of Service Request Severity To ensure that all service requests are reported in a standard format, Cisco has established severity definitions. Severity 1 (S1)—Your network is “down,” or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.
• iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies learn how they can use technology to increase revenue, streamline their business, and expand services. The publication identifies the challenges facing these companies and the technologies to help solve them, using real-world case studies and business strategies to help readers make sound technology investment decisions. You can access iQ Magazine at this URL: http://www.cisco.
Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 European Headquarters Cisco Systems International BV Haarlerbergpark Haarlerbergweg 13-19 1101 CH Amsterdam The Netherlands www-europe.cisco.com Tel: 31 0 20 357 1000 Fax: 31 0 20 357 1100 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA www.cisco.