User's Manual
Table Of Contents
- Cisco ONS 15454 SDH Reference Manual
- Contents
- About this Guide
- Shelf and FMEC Hardware
- Common Control Cards
- Electrical Cards
- Optical Cards
- Ethernet Cards
- Storage Access Networking Cards
- Card Protection
- Cisco Transport Controller Operation
- Security and Timing
- Circuits and Tunnels
- SDH Topologies and Upgrades
- CTC Network Connectivity
- Alarm Monitoring and Management
- Ethernet Operation
- Hardware Specifications
- A.1 Shelf Specifications
- A.2 SFP Specifications
- A.3 General Card Specifications
- A.4 Common Control Card Specifications
- A.5 Electrical Card and FMEC Specifications
- A.5.1 E1-N-14 Card Specifications
- A.5.2 E1-42 Card Specifications
- A.5.3 E3-12 Card Specifications
- A.5.4 DS3i-N-12 Card Specifications
- A.5.5 STM1E-12 Card Specifications
- A.5.6 BLANK Card
- A.5.7 FMEC-E1 Specifications
- A.5.8 FMEC-DS1/E1 Card Specifications
- A.5.9 FMEC E1-120NP Card Specifications
- A.5.10 FMEC E1-120PROA Card Specifications
- A.5.11 FMEC E1-120PROB Card Specifications
- A.5.12 E1-75/120 Impedance Conversion Panel Specifications
- A.5.13 FMEC-E3/DS3 Card Specifications
- A.5.14 FMEC STM1E 1:1 Card Specifications
- A.5.15 FMEC-BLANK Card Specifications
- A.5.16 MIC-A/P Card Specifications
- A.5.17 MIC-C/T/P Card Specifications
- A.6 Optical Card Specifications
- A.6.1 OC3 IR 4/STM1 SH 1310 Card Specifications
- A.6.2 OC3 IR/STM1 SH 1310-8 Card Specifications
- A.6.3 OC12 IR/STM4 SH 1310 Card Specifications
- A.6.4 OC12 LR/STM4 LH 1310 Card Specifications
- A.6.5 OC12 LR/STM4 LH 1550 Card Specifications
- A.6.6 OC12 IR/STM4 SH 1310-4 Card Specifications
- A.6.7 OC48 IR/STM16 SH AS 1310 Card Specifications
- A.6.8 OC48 LR/STM16 LH AS 1550 Card Specifications
- A.6.9 OC48 ELR/STM16 EH 100 GHz Card Specifications
- A.6.10 OC192 SR/STM64 IO 1310 Card Specifications
- A.6.11 OC192 IR/STM64 SH 1550 Card Specifications
- A.6.12 OC192 LR/STM64 LH 1550 Card Specifications
- A.6.13 OC192 LR/STM64 LH ITU 15xx.xx Card Specifications
- A.7 Ethernet Card Specifications
- A.8 Storage Access Networking Card Specifications
- Administrative and Service States
- Network Element Defaults
- Index
3-2
Cisco ONS 15454 SDH Reference Manual, R5.0
April 2008
Chapter 3 Electrical Cards
3.1.1 Card Summary
Note Each card is marked with a symbol that corresponds to a slot (or slots) on the ONS 15454 shelf assembly.
The cards are then installed into slots displaying the same symbols. See the “1.12.1 Card Slot
Requirements” section on page 1-15 for a list of slots and symbols.
3.1.1 Card Summary
Table 3-1 shows available electrical cards for the ONS 15454 SDH.
Table 3-1 Electrical Cards
Card Description For Additional Information...
E1-N-14 Provides 14 E-1 ports and supports 1:0,
1:1, and 1:N protection. It operates in
Slots 1 to 5 and Slots 13 to 17.
See the “3.2 E1-N-14 Card”
section on page 3-4.
E1-42 Provides 42 E-1 ports and supports 1:3
protection. It operates in Slots 1 to 4 and
Slots 14 to 17.
See the “3.3 E1-42 Card”
section on page 3-6.
E3-12 Provides 12 E-3 ports and supports 1:0
and 1:1 protection. It operates in Slots 1
to 5 and Slots 13 to 17.
See the “3.4 E3-12 Card”
section on page 3-8.
DS3i-N-12 Provides 12 DS-3 ports and supports 1:0,
1:1, and 1:N protection. It operates in
Slots 1 to 5 and Slots 13 to 17.
See the “3.5 DS3i-N-12
Card” section on page 3-10.
STM1E-12 Provides 12 electrical STM-1 ports and
supports 1:1 protection. It operates in
Slots 1 to 4 and Slots 14 to 17.
See the “3.6 STM1E-12
Card” section on page 3-13.
BLANK Assures fulfillment of EMC
requirements in case of empty interface
card slots.
See the “3.7 BLANK Card”
section on page 3-14.
FMEC-E1 Provides electrical connection into the
system for 14 pairs of 75-ohm 1.0/2.3
miniature coax connectors for
unbalanced E-1 ports from the E1-N-14
card.
See the “3.8 FMEC-E1 Card”
section on page 3-15.
FMEC-DS1/E1 Provides electrical connection into the
system for 14 pairs of 120-ohm balanced
E-1 ports from the E1-N-14 card. It uses
high-density 37-pin DB connectors.
See the “3.9 FMEC-DS1/E1
Card” section on page 3-16.
FMEC E1-120NP Provides electrical connection into the
system for 42 pairs of 120-ohm balanced
E-1 ports from the E1-42 card. It uses
Molex 96-pin LFH connectors.
See the “3.10 FMEC
E1-120NP Card” section on
page 3-18.