Installation Manual Part 3

PRELIMINARY
7-38
BWX 8415 Basestation Installation and Commissioning Guide
OL-19519-01
Chapter 7 Commissioning
7.7.3 Calibration Procedure
When the BS is calibrated, the measured values are stored in the BS and then reported to the EMS to be
stored under Air Interface > Layer 1. The Digital card pre-calibration values are placed in the General
tab. The TX and RX gain values are placed in the Antenna Table.
7.7.3 Calibration Procedure
Before you can calibrate, ensure the following requirements are met:
• The BS must have been previously added and configured in the EMS database
• The BS must be powered up for at least 15 minutes, booted properly, stable (not resetting) and all
alarms cleared before running the calibration
• Select the BS on the EMS CAM by clicking on the BS
Note The BS must be provisioned before you can calibrate. If the BS is not provisioned, refer to
7.6.3 Provision the BWX 8415 Basestation for the steps to perform the provisioning.
Step 1 Select Air Interface > Layer 1 > Layer 1 Tables.
Step 2 Click on Show Configuration.
Step 3 From a terminal emulation program type in the command, caldebugon and hit <Enter> (Figure 7-42).
Figure 7-42 Show Configuration
Step 4 With the Antenna Table tab selected, click on Calibrate
Step 5 Select Full Calibration and Calibrate and then click on Yes . Refer to Figure 7-43.
bts-221 [Active]% caldebugon
bts221 [Active]%
Make sure you type "caldebugof f
when you are done with the calibration!!!
Terminal Emulation Program
bts-221 [Active]% caldebugon
bts221 [Active]%
Make sure you type "caldebugof f
when you are done with the calibration!!!
Terminal Emulation Program
bts-221 [Active]% caldebugon
bts221 [Active]%
Make sure you type "caldebugof f
when you are done with the calibration!!!
Terminal Emulation Program
bts-221 [Active]% caldebugon
bts221 [Active]%
Make sure you type "caldebugof f
when you are done with the calibration!!!
Terminal Emulation Program
bts-221 [Active]% caldebugon
bts221 [Active]%
Make sure you type "caldebugof f
when you are done with the calibration!!!
Terminal Emulation Program
bts-221 [Active]% caldebugon
bts221 [Active]%
Make sure you type "caldebugof f
when you are done with the calibration!!!
Terminal Emulation Program
bts-221 [Active]% caldebugon
bts221 [Active]%
Make sure you type "caldebugof f
when you are done with the calibration!!!
Terminal Emulation Program
bts-221 [Active]% caldebugon
bts221 [Active]%
Make sure you type "caldebugof f
when you are done with the calibration!!!
Terminal Emulation Program
bts-221 [Active]% caldebugon
bts221 [Active]%
Make sure you type "caldebugof f
when you are done with the calibration!!!
Terminal Emulation Program
bts-221 [Active]% caldebugon
bts221 [Active]%
Make sure you type "caldebugof f
when you are done with the calibration!!!
Terminal Emulation Program
bts-221 [Active]% caldebugon
bts221 [Active]%
Make sure you type "caldebugof f
when you are done with the calibration!!!
Terminal Emulation Program
bts-221 [Active]% caldebugon
bts221 [Active]%
Make sure you type "caldebugof f
when you are done with the calibration!!!
Terminal Emulation Program
bts-221 [Active]% caldebugon
bts221 [Active]%
Make sure you type "caldebugof f
when you are done with the calibration!!!
Terminal Emulation Program
bts-221 [Active]% caldebugon
bts221 [Active]%
Make sure you type "caldebugof f
when you are done with the calibration!!!
Terminal Emulation Program
bts-221 [Active]% caldebugon
bts221 [Active]%
Make sure you type "caldebugof f
when you are done with the calibration!!!
Terminal Emulation Program
bts-221 [Active]% caldebugon
bts221 [Active]%
Make sure you type "caldebugof f
when you are done with the calibration!!!
Terminal Emulation Program