Installation Manual Part 4
Table Of Contents
- Commissioning
- 7.1 Install the Element Management System (EMS)
- 7.2 Install Access Services Network Gateway (ASN-GW) Hardware and Broadband Wireless Gateway (BWG) Software
- 7.3 Add and Configure the BWG to the EMS Server
- 7.4 Authentication, Authorization, and Accounting (AAA) Server Installation
- 7.5 Add and Configure a BWX 8415 Basestation
- 7.6 Power Up and Provision the BWX 8415 Basestation
PRELIMINARY
7-31
BWX 8415 Basestation Installation and Commissioning Guide
OL-19519-01
Chapter 7 Commissioning
7.6.2 BWX 8415 Basestation Bootup
Example 7-3 Changing the Boot Parameter Values (NEED NEW BOOT SEQUENCE SCREENSHOTS)
Example 7-4 Continuation of the Boot Process (NEED NEW BOOT SEQUENCE SCREENSHOTS)
[Navini Boot]: p
date and time : 10/22/2008[14:22]
autoboot countdown : delayed
ems inet : 192.168.2.208
snmp community : public
traffic path : enet
mac address : 00:04:6a:00:3b:cc
ip on enet (active) : 192.168.2.67
ip on enet (standby) : 192.168.2.68
netmask on enet : 255.255.255.0
mgmt vlan id|priority: 1:0 [1-4094]:[0-7]
ip on backplane : 10.0.0.1
gateway on enet : 192.168.2.1
[Navini Boot]:
[Navini Boot]: @
CPLD Firmware Version: 0x18
Starting File System......................Done
Mounting Drive /dev0......................Done
Starting TCP/IP Stack.....................Done
Attached TCP/IP interface to mv unit 0
Attaching interface lo0...done
Mounting Remote Filesystem................
Default Route added,Gateway = 192.168.2.1
Host 172.31.26.201 added to host table ...........Done
Starting Telnet Daemon....................Done
Starting Load Monitoring Tools............Done
Loading symbol table from /cf/LOADS/BTSB/core.sym ..Done
Starting WDB Tools........................Done
Starting Target Shell.....................Done
Initializing System Logger................Done
At the prompt, type "p"
and hit <Enter> to verify
the changes
Enter "c" for changes;
"@" to continue
33
33
33
33
Programming System Support Fpga ..........Done
Programming Shazam Fpga ..................Done
Programming Aphex Fpga ...................Done
Programming RF Fpga ......................Done
Starting L1 DSP Bootloader ........................
WIMAX APP
CP Image Path = /cf/LOADS/BTSB/CP01_MX_IMAGE.bin ... : File open - Success
PP01 Image Path = /cf/LOADS/BTSB/CCP01_MX_IMAGE.bin ... : File open - Success
XP Image Path = /cf/LOADS/BTSB/XP_MX_IMAGE.bin ... : File open - Success
Reset Vals = 0
------------------- DSP STATUS REGISTERS -------------------------
--------------------------------------------------------------------
|GDSW Ver|ResetReg|AUX|PP01|PP23|PP45|PP67|CP01|CP23|CP45|CP67|CP89|
--------------------------------------------------------------------
| 98 | 0 | b | b | 0 | 0 | 0 | b | b | b | b | 0 |
--------------------------------------------------------------------
Starting MPC184 Security Processor........Done
Enable All: XP, CCP, [4]CPs (DSP Bootline Flag: 0x5f)...BootlineMask = 5f
Calling OAM Mem Pool
##########Starting L2 Tasks############
START BtsL2L3If::BtsL2L3If
OAM Mem Pool... Done
Initializing GDSW Parameters..............Done
Starting MCE..............................Done
Starting AsnCom...........................Done
Starting AsnComRx.........................Done
Starting MME..............................Done
Initializing OAM MemPools .............Done
Initializing L2 Applications.....................Done
Initializing Doubly List..................Done
Starting BTS L2 L1If .....................Done