Installation Manual Part 4
Table Of Contents
- Commissioning
- 7.1 Install the Element Management System (EMS)
- 7.2 Install Access Services Network Gateway (ASN-GW) Hardware and Broadband Wireless Gateway (BWG) Software
- 7.3 Add and Configure the BWG to the EMS Server
- 7.4 Authentication, Authorization, and Accounting (AAA) Server Installation
- 7.5 Add and Configure a BWX 8415 Basestation
- 7.6 Power Up and Provision the BWX 8415 Basestation
PRELIMINARY
7-33
BWX 8415 Basestation Installation and Commissioning Guide
OL-19519-01
Chapter 7 Commissioning
7.6.2 BWX 8415 Basestation Bootup
Example 7-6 Continuation of the Boot Process (NEED NEW BOOT SEQUENCE SCREENSHOTS)
Example 7-7 Completion of the Boot Process (NEED NEW BOOT SEQUENCE SCREENSHOTS)
When booting from the EMS you get this:
Selecting Config Data Source as EMS.......Done
Initializing NvRam Mib....................Done
Initializing SNMP Agent...................Done
EMS (192.168.2.208) Ping Attempt..........Done
Selecting Config Data Source as EMS.......Done
Initializing NvRam Mib....................Done
Initializing SNMP Agent...................Done
EMS (192.168.2.208) Ping Attempt..........Done
Requesting EMS for Configuration Data.....Done
Configuring BTS from EMS..................Done
Starting MMM..............................Done
Starting Sfm..............................Done
!!!!!!!! BTS Initialization Complete !!!!!!!!!
This step may take a few moments. If the BTS
fails to receive the configuration data from the
EMS (the line will say “Pending” instead of
“Done”), this step will timeout and the BTS will
request the configuration data data again. If
the BTS keeps trying and trying and still does
not get the data from the EMS (each iteration
may take 3 or 4 minutes), there is a
communication problem between the BTS and
the EMS. Check the Ethernet connections
and/or the EMS IP address under SystemÆ
General in the BTS Configuration record.
This step may take a few moments. If the BTS
fails to receive the configuration data from the
EMS (the line will say “Pending” instead of
“Done”), this step will timeout and the BTS will
request the configuration data data again. If
the BTS keeps trying and trying and still does
not get the data from the EMS (each iteration
may take 3 or 4 minutes), there is a
communication problem between the BTS and
the EMS. Check the Ethernet connections
and/or the EMS IP address under SystemÆ
General in the BTS Configuration record.
CCC CCC (TM)
CCC CCC
CCC CCC
CCC CCC CCC CCC CCC CCC
CCC CCC CCC CCC CCC CCC
CCC CCC CCC CCC CCC CCC
CCC CCC CCC CCC CCC CCC CCC CCC CCC
CCC CCC CCC CCC CCC CCC CCC CCC CCC
CCC CCC CCC CCC CCC CCC CCC CCC CCC
CCC CCC CCC CCC CCC CCC CCC CCC CCC P R O F I L E C
CCC CCC CCC CCC CCC CCC CCC CCC CCC
CCC CCC CCC CCC CCC CCC CCC CCC CCC
CCC CCC CCC CCC CCC CCC CCC CCC CCC
CCC CCC Copyright (c) Cisco Systems, Inc. 2008
CCC CCC Copyright (c) Texas Instruments, Inc. 2000-2001
CCC CCC Copyright (c) Wind River Systems, Inc. 1984-2002
### ##### #### ### ###
## ## ## ## ## ## ## ## ##
## ## ## ## ## ##
## ## ## ## ## ##
## ## ## ## ## ##
## ## ## ## ## ## ## ## ##
### ##### #### ### ###
S Y S T E M S
KERNEL : VxWorks5.5.1(WIND version 2.6)
BSP : 1.5RW7.0.2.9
CPU: Cisco Nero 7447A Power PC. Processor #0.
Memory Size: 0xfe00000.
WDB: Ready.
Reset Reason: S_RESET
Current time is WED OCT 22 14:27:22 2008
S_RESET means reboot from the console. Also possible
are UNKNOWN ("hard reset"), EMS_RESET (Reset BTS
from the EMS) and WATCHDOG (BTS rebooted by itself)
S_RESET means reboot from the console. Also possible
are UNKNOWN ("hard reset"), EMS_RESET (Reset BTS
from the EMS) and WATCHDOG (BTS rebooted by itself)