Installation Manual Part 4

PRELIMINARY
7-5
BWX 8415 Basestation Installation and Commissioning Guide
OL-19519-01
Chapter 7 Commissioning
7.1.3 Install the BWX EMS Software and Start & Configure the BWX EMS Server
Figure 7-4 Stopping the EMS Server
7.1.3.3 Configure the BWX EMS Server
Note The minimum configuration that you will enter into the EMS server will be through the Configuration
& Alarm Manager (CAM) application, which is a graphical user interface (GUI). If you are not already
familiar with the CAM, please review the BWX Mobile WiMAX Configuration Guide.
Please refer to the BWX Mobile WiMAX Configuration Guide for instructions on the configuration of the
EMS server. The configuration of the EMS server includes the following elements:
• General configuration
• Alarm Management configuration
• Performance Management configuration
7.1.3.3.1 General Configuration
General configuration of the EMS server includes changing the EMS ID & Network ID fields, entering
the FTP user name, password & FTP server root path, and entering the BTS/CPE SW Directory.
Note The software upgrade files for BSs and Subscriber Stations (SSs) must be stored on the same PC where
the EMS Server was installed. An FTP server must also be installed on that same PC. Under the FTP
server you must add a user, give this user a password, and assign this user a root default directory. Under
the EMS tab, this user, password, and root directory must be specified during configuration. To do an
upgrade, the file(s) are placed on that directory, and the process is initiated on the EMS, which
communicates with the FTP server (which is the one that does the actual transfer). Refer to Figure 7-5.
If this does not work, then
Enter <CTRL>C at the EMS
Server window to Stop the
EMS. When asked if you
want to terminate the batch
file, enter “N” to gracefully
stop all the other processes
3. Allow time for the EMS
shutdown process to
execute. When the process
is com pleted, this window
will close by itself
NEVER CLOSE THE
EMS WINDOW BY
CLICKING ON THE “X”
"
"
4. The window closes
4. The window closes
4. The window closes
4. The window closes
ciscolaptop
2. When prompted, enter <adminPassword>
1. Open a Command Prompt window and enter stopemsserver <adminID>
5. Close the Command
prompt window
If this does not work, then
Enter <CTRL>C at the EMS
Server window to Stop the
EMS. When asked if you
want to terminate the batch
file, enter “N” to gracefully
stop all the other processes
3. Allow time for the EMS
shutdown process to
execute. When the process
is com pleted, this window
will close by itself
NEVER CLOSE THE
EMS WINDOW BY
CLICKING ON THE “X”
"
"
4. The window closes
4. The window closes
4. The window closes
4. The window closes
If this does not work, then
Enter <CTRL>C at the EMS
Server window to Stop the
EMS. When asked if you
want to terminate the batch
file, enter “N” to gracefully
stop all the other processes
If this does not work, then
Enter <CTRL>C at the EMS
Server window to Stop the
EMS. When asked if you
want to terminate the batch
file, enter “N” to gracefully
stop all the other processes
3. Allow time for the EMS
shutdown process to
execute. When the process
is com pleted, this window
will close by itself
NEVER CLOSE THE
EMS WINDOW BY
CLICKING ON THE “X”
"
"
4. The window closes
4. The window closes
4. The window closes
4. The window closes
3. Allow time for the EMS
shutdown process to
execute. When the process
is com pleted, this window
will close by itself
3. Allow time for the EMS
shutdown process to
execute. When the process
is com pleted, this window
will close by itself
3. Allow time for the EMS
shutdown process to
execute. When the process
is com pleted, this window
will close by itself
NEVER CLOSE THE
EMS WINDOW BY
CLICKING ON THE “X”
"
"
4. The window closes
4. The window closes
4. The window closes
4. The window closes
NEVER CLOSE THE
EMS WINDOW BY
CLICKING ON THE “X”
"
"
NEVER CLOSE THE
EMS WINDOW BY
CLICKING ON THE “X”
NEVER CLOSE THE
EMS WINDOW BY
CLICKING ON THE “X”
"
"""
4. The window closes
4. The window closes
4. The window closes
4. The window closes
4. The window closes
4. The window closes
4. The window closes
4. The window closes
ciscolaptop
2. When prompted, enter <adminPassword>
1. Open a Command Prompt window and enter stopemsserver <adminID>
5. Close the Command
prompt window
ciscolaptop
2. When prompted, enter <adminPassword>
ciscolaptopciscolaptopciscolaptop
2. When prompted, enter <adminPassword>2. When prompted, enter <adminPassword>
1. Open a Command Prompt window and enter stopemsserver <adminID>1. Open a Command Prompt window and enter stopemsserver <adminID>1. Open a Command Prompt window and enter stopemsserver <adminID>
5. Close the Command
prompt window
5. Close the Command
prompt window
5. Close the Command
prompt window