Ripwave™ Base Station Installation & Commissioning Guide Part Number 40-00047-00 Revision H, Version 1.0 February 4, 2005 Proprietary All information disclosed by this document is the proprietary property of Navini Networks, Inc. and is protected by copyright, trademark, and/or trade secret laws. All rights therein are expressly reserved.
Navini Networks, Inc. Ripwave Base Station I&C Guide About This Document Purpose This document provides a Navini-certified Installation & Commissioning Technician or Field Engineer with instructions to properly install the Base Transceiver Station (BTS), Radio Frequency Subsystem (RFS), and cabling; and to test and commission the Base Station after installation. Revision History Date 1.31.05 2.4.05 Revision/ Version H/1.0 H/1.0 Authors Editors Comments L. Font L. Font S. Redfoot S.
Navini Networks, Inc. Ripwave Base Station I&C Guide Permissions, Trademarks & Distribution Copyright © 2005, Navini Networks, Inc. All information contained herein and disclosed by this document is the proprietary property of Navini Networks, Inc. and all rights therein are expressly reserved. Acceptance of this material signifies agreement by the recipient that the information contained in this document is confidential and that it will be used solely for the purposes set forth herein.
Navini Networks, Inc. Ripwave Base Station I&C Guide Table of Contents CHAPTER 1: OVERVIEW......................................................................ERROR! BOOKMARK NOT DEFINED. RIPWAVE DESCRIPTION .....................................................................................ERROR! BOOKMARK NOT DEFINED. PROCEDURAL DOCUMENTS & FORMS ...............................................................ERROR! BOOKMARK NOT DEFINED. HIGH-LEVEL I&C PROCESS ...........................................
Navini Networks, Inc. Ripwave Base Station I&C Guide Safety To optimize safety and expedite installation and service, read this document thoroughly. Follow all warnings, cautions, and instructions marked on the equipment and included in this document. To aid in the prevention of injury and damage to property, cautionary symbols have been placed in this document to alert the reader to known potentially hazardous situations, or hazards to equipment or procedures.
Navini Networks, Inc. Ripwave Base Station I&C Guide the equipment. 11. Do not disassemble the equipment. Removing covers exposes dangerous voltages or other risks and also voids the warranty. Incorrect reassembly can cause equipment damage or electrical shock. Only an authorized repair technician should service this product. 12. Do not expose the equipment to extreme hot or cold temperatures. 13.
Navini Networks, Inc. Ripwave Base Station I&C Guide Regulatory & Safety Information Safety Notice WARNING! This device is a Radio Frequency transmitter. A minimum separation distance of 2 meters or more must be maintained between the antenna and all persons during device operations to ensure safe operation. If this minimum distance cannot be maintained, exposure to RF levels that exceed safety limits may result. FCC Notice WARNING! This device is a Radio Frequency transmitter.
Navini Networks, Inc. Ripwave Base Station I&C Guide wires and connection points. 9. A UL listed disconnect device, such as a circuit breaker or fuse, must be installed between the power supply and BTS chassis connections. 10. Power-interconnect wires between the power supply/recitifier and the BTS Digital chassis must have heat shrink tubing applied over the barrel of the terminal lugs after crimping the wire. A picture is provided in the “Installation” section of this manual. 11.
Navini Networks, Inc. Ripwave Base Station I&C Guide France: Use of this equipment is limited to the 2446.5-2483.5 MHz band, with some geographical constraints and the EIRP limited to -20dBW/MHz. Indoor: EIRP limited to 10 mW in the 2400-2446 MHz band. Inside a private area: EIRP limited to 100 mW in the 2446-2483.5 MHz band, with authorization. Outside a private area: the band is not opened. Belgium: EIRP limited to 10 mW. Hungary: Processing gain: 10 dB minimum.
Navini Networks, Inc. Ripwave Base Station I&C Guide Países Bajos: No se requiere licencia para operar a 10 mW en interior o exterior. No se requiere licencia para operar a 100 mW en interiores solamente. Se requiere una licencia para operar a 100 mW en la banda de 2451-2471 MHz en el exterior. . Debe protegerse el uso actual de esta banda por parte del gobierno.
Navini Networks, Inc. Ripwave Base Station I&C Guide Battery Caution & Procedures WARNING! To reduce risk of injury or fire, follow these instructions when handling the battery. 1. Risk of explosion is possible if the battery is replaced with one not supplied by Navini Networks. 2. Do not dispose of the battery in a fire. It may explode. Check with the local codes for battery disposal guidelines. 3. Do not open or mutilate the battery.
