Cisco TelePresence System 3000 Assembly Guide Use & Care Guide Field-Replaceable Unit Guide October 31, 2008 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
C O N T E N T S Preface ix Introduction i-ix Conventions i-ix Obtaining Documentation, Obtaining Support, and Security Guidelines Related Documentation i-x i-x i-x Overview 1-1 Chapter Organization Assembly Overview 1-1 1-3 Conventions and Terminology Tools and Equipment List 1-5 Building the Display Assembly Parts List 1-4 2-1 2-1 Mounting and Leveling the Plasma Displays Parts List 3-1 Purpose of Leveling the Plasma displays Leveling Alignment Points 3-4 Leveling Goals 3-5 Completing
Contents Building the Table Assembly, Product ID CTS3K-FUR-MAPLE Building the Table Assembly, Product ID CTS3K-M 6-18 Assembling the Remaining Cisco TelePresence Elements Parts List 8-1 8-1 First-Time Setup Parts List 7-1 7-1 Routing Power and Signal Cables Parts List 6-5 9-1 9-1 Loading CTS Administration Software 9-1 Configuring an Alternate TFTP Server (Optional) 9-4 Setting Up CTS Components 9-4 Setting Up the Displays 9-5 Setting Up the Cameras 9-7 Setting Up the Speakers 9-13 Setting
Contents Removing the Left Tabletop Door Section 11-5 Removing a Display Shelf 11-5 Removing the Display Screen and Completing the Procedure 11-6 Replacing a Speaker—Part Number CTS-LDSPKR 11-8 Required Information, Tools, and Equipment 11-8 Powering Off the System 11-8 Removing and Replacing a Speaker 11-8 Replacing a Codec Unit—Part Number CTS-CODEC-PRI-G2 (Primary Codec) or CTS-CODEC-SEC (Secondary Codec) 11-10 Required Information, Tools, and Equipment 11-10 Powering Off the System 11-10 Removing and
Contents Carton 4 of 47: Secondary Codec, 800-28202-xx, CTS-CODEC-SEC A-3 Carton 5 of 47: Secondary Codec, 800-28202-xx, CTS-CODEC-SEC A-4 Carton 6 of 47: Projector, 74-4824-xx, CTS-PRJTR-GEN1 A-4 Carton 7 of 47: Speaker, 74-4740-xx, CTS-LDSPKR A-4 Carton 8 of 47: Speaker, 74-4740-xx, CTS-LDSPKR A-4 Carton 9 of 47: Speaker, 74-4740-xx, CTS-LDSPKR A-4 Carton 10 of 47: Power Cord, 37-08xx-xx, PWR-CORD10-xx A-5 Carton 11 of 47: Camera Bracket, 69-1627-xx, CTS3K-STRUCTURE A-5 Carton 12 of 47: Brackets, 69-1632
Contents Carton 44 of 47: Tabletop, 69-1638-xx, CTS3K-FUR-MAPLE A-12 Carton 45 of 47: Tabletop, 69-1639-xx, CTS3K-FUR-MAPLE A-13 Carton 46 of 47: Display Shelf, 69-1640-xx, CTS3K-FUR-MAPLE A-13 Carton 47 of 47: Speaker Boards, 69-1641-xx, CTS3K-FUR-MAPLE A-13 Carton List for CTS3K-M Table Shelf and Table Section Assemblies A-13 Carton 1 of 44: Mechanical Accessory Kit, CTS3K-ACC-KIT, 53-2855-xx A-13 Carton 2 of 44: Camera Assembly, 800-28487-xx, CTS3K-CAM-CLUST A-15 Carton 3 of 44: Primary Codec, 800-28191
Contents Carton 36 of 44: Projector Screen, 74-5416-xx, CTS3K-SCREEN A-23 Carton 37 of 44: Accessory Cabinet, Right, 69-1837-xx, CTS3K-M-TABLE-G2 A-23 Carton 38 of 44: Accessory Cabinet, Left, 69-1838-xx, CTS3K-M-TABLE-G2 A-23 Carton 39 of 44: Display Shelf Supports and Codec Tray, 69-1626-xx, CTS3K-STRUCTURE Carton 40 of 44: Tabletop Leg Base, 69-1620-xx, CTS3K-STRUCTURE A-24 Carton 41 of 44: Lighting Assembly, 69-1613-xx, CTS3K-LIGHT-STR A-24 Carton 42 of 44: Projector Bracket, 69-1631-xx, CTS3K-STRUCTUR
Preface Revised: October 31, 2008, OL-14521-01 Introduction The Cisco TelePresence 3000 Assembly Guide outlines the steps and best practices for assembling and installing the Cisco TelePresence 3000. This guide is intended primarily for installers of the Cisco TelePresence System 3200. Site planners, network administrators, and facility maintenance personnel may also find this document useful. This preface provides the following information for using this guide and for accessing other resources.
Preface Obtaining Documentation, Obtaining Support, and Security Guidelines Tip Means the information contains useful tips. Obtaining Documentation, Obtaining Support, and Security Guidelines For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.
CH A P T E R 1 Overview Revised: October 31, 2008, OL-14521-01 Chapter Organization Chapter 1, “Overview” (this chapter) Provides chapter organization and content of this document and includes an overview of the assembly steps you perform. Chapter 2, “Building the Display Assembly” • The steps for assembling the three Display structures, connecting them, and positioning them in the conference room are described in a series of illustrations.
Chapter 1 Overview Chapter Organization • Each element is described using one or more illustrations.
Chapter 1 Overview Assembly Overview View of an Assembled Cisco TelePresence System 3200 CISCO IP PHONE 7970 TelePresence 1 4 GHI 7 PQRS 157320 Figure 1-1 3 2 ABC 5 JKL 8 TUV 0 DEF 6 MNO 9 WXYZ # OPER Assembly Overview Perform the following steps to install a CTS 3000: Step 1 Build the display assembly. See Chapter 2, “Building the Display Assembly” for more information. Step 2 Mount and level the plasma displays.
Chapter 1 Overview Conventions and Terminology c. Install the I/O Modules for the table leg power and Ethernet connections and connect the Ethernet cables. See Step 3 and Step 4 in Chapter 7, “Assembling the Remaining Cisco TelePresence Elements” to install the I/O modules and cables and Step 5 in Chapter 8, “Routing Power and Signal Cables” to connect the Ethernet cables. Step 6 Install the codecs and connect the signal cables.
Chapter 1 Overview Tools and Equipment List Cable Connection Labeling System 157702 Figure 1-2 Tools and Equipment List To assemble the Cisco TelePresence 3000, you need the following tools and equipment: Uncrating and Unpacking: • Claw hammer or small pry bar • Large Phillips screwdriver • Tin snips* • Pallet jack or hand cart (for moving component boxes to installation site)* • Safety gloves* • Safety glasses* • Box cutters* Cisco TelePresence System 3200 Structure, Accessory, and Adjus
Chapter 1 Overview Tools and Equipment List Cisco TelePresence System 3000 1-6 OL-14521-01
CH A P T E R 2 Building the Display Assembly Revised: October 31, 2008, OL-14521-01 Parts List Key Part Description Part Number Qty Ctn 1 Display structure 700-23358-xx 3 35, 36, 37 (CTS3K-FURMAPLE) 32, 33, 34 (CTS3K-M) 2 Rear foot stabilizer 700-23360-xx 6 17 3 Front foot stabilizer 700-23359-xx 6 14, 15, 16 4 Leveling foot 51-4540-xx 12 1 5 Display shelf support left 700-23339-xx 3 40 (CTS3K-FURMAPLE) 39 (CTS3K-M) 6 Display shelf support right 700-23340-xx 3 40 (CTS3K-
Chapter 2 Building the Display Assembly Parts List Caution The display structures are unstable during assembly. Use caution, and support all structures as required. Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Note Step 1 The directions left and right refer to the assembly as you face the Plasma displays. Attach the Leveling feet to the Rear and Front Foot stabilizers.
Chapter 2 Building the Display Assembly Parts List Step 2 Note Attach the Codec Safety trays to the Front Foot stabilizers. If you ordered a Presentation Codec, attach the larger tray that comes with the Presentation Codec package, part no. 700-25301-xx, in the center display. Refer to the Cisco TelePresence Hardware Options and Upgrade Guide for more information.
Chapter 2 Building the Display Assembly Parts List Step 3 Attach the Rear and Front Foot stabilizers to the Display structures.
Chapter 2 Building the Display Assembly Parts List Step 4 Attach the left and right Display Shelf supports to each Display structure.
Chapter 2 Building the Display Assembly Parts List Step 5 Attach the Display Tilt brackets to each Display structure. Figure 2-5 Display Tilt brackets 7 1 12 13 201104 7 Note Do not tighten the Display Tilt brackets. You will need to adjust them to level the Plasma displays in Chapter 3, “Mounting and Leveling the Plasma Displays.
Chapter 2 Building the Display Assembly Parts List Step 6 Attach the Camera Assembly bracket to the center Display structure. Figure 2-6 Camera Assembly bracket 13 9 13 201105 1 Note The Camera Assembly bracket attaches to the center Display structure.
Chapter 2 Building the Display Assembly Parts List Step 7 Attach the upper and lower Support crossbars to the left and right Display structures. Figure 2-7 11 Upper and Lower Support crossbars 12 1 10 201107 10 Tip Use the screw holes nearest the ends of the Support crossbars.
Chapter 2 Building the Display Assembly Parts List Step 8 Figure 2-8 Attach the upper and lower Support crossbars to the center Display structure.
Chapter 2 Building the Display Assembly Parts List Step 9 Figure 2-9 Position the three Display structures relative to the rear wall. Positioning the Display Structures 18 - 22” (45.7 cm - 55.
CH A P T E R 3 Mounting and Leveling the Plasma Displays Revised: October 31, 2008, OL-14521-01 Parts List Key Part Description Part Number Qty Ctn 1 65-inch high-definition display 74-4881-03 3 20, 21, 22 2 Black buffer strips 700-23981-xx 2 1 3 Display shelves 700-23600-xx, 700-23599-xx, 700-23598-xx (CTS3K-FURMAPLE) 700-23339-xx, 700-23340-xx, 700-23341-xx (CTS3K-M) 3 46 (CTS3K-FURMAPLE) 4 M8 x 20 mm screws Warning 48-2273-xx 44 (CTS3K-M) Notes The Display shelves are used in
Chapter 3 Mounting and Leveling the Plasma Displays Parts List Step 1 Hang the left, center, and right Plasma displays on the Display structure crossbars Caution Make sure the Plasma display Leveling feet remain firmly seated on top of the Display shelf supports. The left, center, and right Plasma displays 201109 Figure 3-1 Caution The edges of the Plasma displays are sharp and uncomfortable to lift with bare hands. Nonslip gloves are recommended.
Chapter 3 Mounting and Leveling the Plasma Displays Parts List Step 2 Attach the Display shelves to the Display shelf supports Attach the Display shelves to the Display shelf supports 201111 Figure 3-2 Note The Display shelves are used in this chapter for leveling purposes only. The Display shelves and the attaching bracketing hardware are described in Chapter 5, Building the Display Shelf Assembly. Use the M8 x 20 mm screws in the Accessory Kit to attach the Display shelves.
Chapter 3 Mounting and Leveling the Plasma Displays Purpose of Leveling the Plasma displays Purpose of Leveling the Plasma displays The three Plasma displays act as windows allowing a three-way view into the remote Cisco TelePresence conference room. The Display shelf in front of each Plasma display acts as a visual bridge between the local and remote conference rooms.
Chapter 3 Mounting and Leveling the Plasma Displays Purpose of Leveling the Plasma displays Leveling Goals Leveling the Display shelves and the Plasma displays, and aligning the seams of the Display shelves with the edges of the Plasma displays insures that images displayed from the remote conference room match the local conference room configuration. The leveling goals illustrated in Figure 3-4 through Figure 3-8 show how to use the leveling alignment points in Figure 3-3.
Chapter 3 Mounting and Leveling the Plasma Displays Purpose of Leveling the Plasma displays Step 5 The surface of the Display shelves should not obstruct any lines of resolution. Use the Plasma display Leveling feet to raise or lower the Plasma displays and make sure all lines of resolution can be seen when sitting at the conference table.
Chapter 3 Mounting and Leveling the Plasma Displays Purpose of Leveling the Plasma displays Step 6 Tip Use the Plasma display Leveling feet to level the Plasma displays along the X axis. Use the Display tilt brackets to level the Plasma displays along the Y axis. You should level the center Plasma display first. Then align the left and right Plasma displays to the center display.
Chapter 3 Mounting and Leveling the Plasma Displays Purpose of Leveling the Plasma displays Step 7 Align the edges of Plasma displays The gap between Plasma displays should be uniformly even from the top edge of the Plasma display to the bottom edge. You should try to make the gap as small as possible.
Chapter 3 Mounting and Leveling the Plasma Displays Purpose of Leveling the Plasma displays Step 8 Align the seams of the Display shelves with the seams between Plasma displays. You may need to adjust the Plasma displays left to right so the seam created between the edges of two Plasma displays are aligned to the corresponding Display shelf seam.
Chapter 3 Mounting and Leveling the Plasma Displays Completing the Plasma display setup Completing the Plasma display setup Step 9 Apply the Black Buffer strips 201119 Figure 3-9 Apply the Black Buffer strips Cisco TelePresence System 3000 3-10 OL-14521-01
CH A P T E R 4 Building the Lighting Assembly Revised: October 31, 2008, OL-14521-01 Parts List Key Part Description Part Number Qty Ctn 1 Notes Lighting support brackets 700-23749-xx 6 26 (CTS3K-FUR-MAPLE) 23 (CTS3K-M) 2 Support struts 700-23752-xx 6 26 (CTS3K-FUR-MAPLE) 23 (CTS3K-M) 3 End structure brackets 700-23750-xx 4 26 (CTS3K-FUR-MAPLE) 23 (CTS3K-M) 4 Plastic diffuser panel: center 700-23745-xx 1 26 (CTS3K-FUR-MAPLE) 23 (CTS3K-M) 5 Plastic diffuser panel: ends 700-23746
Chapter 4 Building the Lighting Assembly Parts List Key Part Description Part Number Qty Ctn 14 Reflector bottom: top side 700-23827-xx 2 26 (CTS3K-FUR-MAPLE) 23 (CTS3K-M) 15 Reflector bottom: end 700-23828-xx 2 26 (CTS3K-FUR-MAPLE) 23 (CTS3K-M) 16 Reflector bottom spacer 700-24152-xx 2 26 (CTS3K-FUR-MAPLE) 23 (CTS3K-M) 17 Reflector top: center 700-23731-xx 1 26 (CTS3K-FUR-MAPLE) 23 (CTS3K-M) 18 Reflector top: top side 700-23734-xx 2 26 (CTS3K-FUR-MAPLE) 23 (CTS3K-M) 19 Refl
Chapter 4 Building the Lighting Assembly Parts List Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Caution Metal and plastic edges can be sharp. Cisco recommends you wear safety gloves and safety glasses when attaching the lighting assembly. Note The directions left and right refer to the assembly as you face the Plasma displays.
Chapter 4 Building the Lighting Assembly Parts List Step 1 Assemble the six Support struts and six Lighting Support brackets.
Chapter 4 Building the Lighting Assembly Parts List Step 2 Attach the left and right outer Support brackets (from Figure 4-1) to the horizontal bar on the left and right Display structures. Figure 4-2 Left and Right outer Support brackets (from Figure 4-1) 31 1 2 201126 31 Note There is no physical difference between the six Support brackets assembled in Figure 4-1. Any two can be used as outer Support brackets.
Chapter 4 Building the Lighting Assembly Parts List Step 3 Attach the four inner Support brackets to the Support crossbars. Figure 4-3 Four inner Support brackets (from Figure 4-1) 1 2 26 201127 31 Note There is no physical difference between the six Support brackets assembled in Figure 4-1. Any two can be used as outer Support brackets.
Chapter 4 Building the Lighting Assembly Parts List Step 4 Attach the four End structure brackets to the ends of the Support crossbars.
Chapter 4 Building the Lighting Assembly Parts List Step 5 Figure 4-5 Attach the three Reflector bottom trays to the Support brackets.
Chapter 4 Building the Lighting Assembly Parts List Step 6 Figure 4-6 Attach the two Reflector bottom spacers to join the three Reflector bottom trays.
Chapter 4 Building the Lighting Assembly Parts List Step 7 Figure 4-7 Attach the left and right (vertical) Reflector Bottom ends to the End Structure brackets and attach the compliance sticker to the left reflector bottom end.
Chapter 4 Building the Lighting Assembly Parts List Step 8 Attach the Light Cup bracket to the left and right (vertical) Reflector Bottom ends.
Chapter 4 Building the Lighting Assembly Parts List Step 9 Figure 4-9 Attach the three 5-foot Light fixtures inside the Reflector bottoms.
Chapter 4 Building the Lighting Assembly Parts List Step 10 Attach the left and right 4-foot Side Light fixtures to the left and right (vertical) Reflector Bottom ends. The power cords for the Side Light fixtures should extend from the top of the fixtures (Figure 4-8).
Chapter 4 Building the Lighting Assembly Parts List Step 11 Figure 4-11 Attach the two center Metal Trim panels.
Chapter 4 Building the Lighting Assembly Parts List Step 12 Figure 4-12 Attach the two side Metal Trim panels.
Chapter 4 Building the Lighting Assembly Parts List Step 13 Figure 4-13 Attach the center Plastic Diffuser panel.
Chapter 4 Building the Lighting Assembly Parts List Step 14 Attach the left and right Plastic Diffuser panels. Note Figure 4-14 The rounded corners of the left and right Plastic Diffuser panels point outward.
Chapter 4 Building the Lighting Assembly Parts List Step 15 Attach the four L-brackets to the two (vertical) end Plastic Diffuser panels.
Chapter 4 Building the Lighting Assembly Parts List Step 16 Figure 4-16 Attach the two (vertical) Plastic Diffuser panels to the End Structure brackets.
Chapter 4 Building the Lighting Assembly Parts List Step 17 Slide the Plastic Diffuser Panel brace between the end (vertical) Plastic Diffuser panel and the left and right Plastic Diffuser panels. Note Figure 4-17 If the diffuser becomes scratched, use a black felt-tip permanent marker to cover the imperfection.
Chapter 4 Building the Lighting Assembly Parts List Step 18 Attach the center Reflector top to the center Reflector bottom. Note Figure 4-18 Do not tighten screws until completing Figure 4-22.
Chapter 4 Building the Lighting Assembly Parts List Step 19 Attach the left and right Reflector tops to the left and right Reflector bottoms. Note Figure 4-19 Do not tighten screws until completing Figure 4-22.
Chapter 4 Building the Lighting Assembly Parts List Step 20 Join the left, center, and right Reflector tops with the left and right Reflector Transition pieces. Note Figure 4-20 Do not tighten screws until completing Figure 4-22.
Chapter 4 Building the Lighting Assembly Parts List Step 21 Attach the left and right (vertical) Reflector ends to the left and right (vertical) Reflector Bottom ends. Note Figure 4-21 Do not tighten screws until completing Figure 4-22.
Chapter 4 Building the Lighting Assembly Parts List Step 22 Attach the left and right corner Reflector Transition pieces to the Reflector tops. Note Figure 4-22 Tighten all screws from Figure 4-18 through Figure 4-22. The goal is to insure the reflector pieces form a “seamless hood” around the lighting assembly.
Chapter 4 Building the Lighting Assembly Parts List Step 23 Attach the two Metal Trim panels to the L-brackets attached to the two (vertical) Plastic Diffuser panels. Note Figure 4-23 These Metal Trim panels cover the access opening used to route cables. You may not want to attach these Metal Trim panels until you complete the cable routing in Chapter 8, “Routing Power and Signal Cables.
CH A P T E R 5 Building the Display Shelf Assembly Revised: October 31, 2008, OL-14521-01 Parts List Key Part Description Part Number Display Shelf, Product ID CTS3K-FUR-MAPLE Qty Ctn 1 Display shelf section: left 700-23600-xx (CTS3K-FURMAPLE) 700-23341-xx (CTS3K-M) 1 46 2 Display shelf section: center 700-23599-xx (CTS3K-FURMAPLE) 700-23340-xx (CTS3K-M) 1 46 3 Display shelf section: right 700-23598-xx (CTS3K-FURMAPLE) 700-23339-xx, (CTS3K-M) 1 46 4 Not used 5 Left accessory cabinet a
Chapter 5 Building the Display Shelf Assembly Parts List Key Part Description Part Number Qty Ctn 12 M4 x 12 mm pan head screws 69-1878-xx 48-2426-xx 13 M8 x 30 mm screw 48-2313-xx 15 1 14 Cam lock coupling 51-4580-xx 20 1 Notes 1 Accessory Cabinet 1 Accessory cabinet, right 700-23601-xx 1 42, 43 2 Accessory cabinet, left 700-23601-xx 1 42, 43 3 Assembly Screen Supports No part number 2 1 48-2273-xx 14 1 4 and M8 x 20 mm screws 12 These brackets might also be located
Chapter 5 Building the Display Shelf Assembly Determining the Display Shelf Type 14 M4 x 12 mm pan head screws 69-1878-xx 48-2426-xx 16 1 For connecting plates Accessory Cabinet 1 Accessory Cabinet, Right 74-5297-xx Kit # 69-1837-xx 1 37 2 Accessory Cabinet, Left 74-5298-xx Kit #69-1838-xx 1 38 3 Assembly Screen Supports No part number 2 1 48-2273-xx 14 1 4 and M8 x 20 mm screws 12 Caution Warning Caution Note These brackets might also be located inside of the assembly cabinet
Chapter 5 Building the Display Shelf Assembly Determining the Display Shelf Type – Display shelves with a product ID of CTS3K-FUR-MAPLE use cam locks, cam lock rods, and plates to attach the sections. – Display shelves with a product ID of CTS3K-M use draw bolts to attach the sections. Figure 5-1 shows the attachment hardware differences.
Chapter 5 Building the Display Shelf Assembly Building the Display Shelf Assembly, Product ID CTS3K-FUR-MAPLE Building the Display Shelf Assembly, Product ID CTS3K-FUR-MAPLE Step 1 Figure 5-2 Attach the Display shelf hardware to the display shelves.
Chapter 5 Building the Display Shelf Assembly Building the Display Shelf Assembly, Product ID CTS3K-FUR-MAPLE Step 2 Figure 5-3 Attach the left Display shelf.
Chapter 5 Building the Display Shelf Assembly Building the Display Shelf Assembly, Product ID CTS3K-FUR-MAPLE Step 3 Figure 5-4 Attach the center Display shelf Center Display shelf 13 Note 201149 2 13 Refer to Figure 5-2 to see the hardware used to attach the center Display shelf to the left Display shelf.
Chapter 5 Building the Display Shelf Assembly Building the Display Shelf Assembly, Product ID CTS3K-FUR-MAPLE Step 4 Figure 5-5 Attach the right Display shelf. Right Display shelf 13 Note 13 201150 3 Refer to Figure 5-2 to see the hardware used to attach the right Display shelf to the center Display shelf.
Chapter 5 Building the Display Shelf Assembly Building the Display Shelf Assembly, Product ID CTS3K-FUR-MAPLE Step 5 Attach the screen supports to the accessory cabinets and position, but do not attach, the cabinets to the left and right attachment brackets These screen supports are only required if you use a Type 1 projector screen, part number 800-28681-xx. If your installation uses the projector screen with a product ID of CTS3K-SCREEN and a part number of 74-5416-xx, do not install these brackets.
Chapter 5 Building the Display Shelf Assembly Building the Display Shelf Assembly, Product ID CTS3K-M Building the Display Shelf Assembly, Product ID CTS3K-M Step 1 Figure 5-7 Attach the Display shelf hardware to the display shelves. Display Shelf Hardware 14 14 8 8 12 9 5 12 12 9 6 3 10 11 205467 1 Note The Right Accessory Cabinet attachment bracket (marked “6” in the illustration), has a central rectangular hole that differentiates it from the Left Accessory Cabinet attachment bracket.
Chapter 5 Building the Display Shelf Assembly Building the Display Shelf Assembly, Product ID CTS3K-M Step 2 Figure 5-8 Attach the left Display shelf.
Chapter 5 Building the Display Shelf Assembly Building the Display Shelf Assembly, Product ID CTS3K-M Step 3 Figure 5-9 Attach the center Display shelf Center Display shelf 13 13 Note 201149 2 Refer to Figure 5-2 to see the hardware used to attach the center Display shelf to the left Display shelf.
Chapter 5 Building the Display Shelf Assembly Building the Display Shelf Assembly, Product ID CTS3K-M Step 4 Figure 5-10 Attach the right Display shelf. Right Display shelf 13 Note 201150 3 13 Refer to Figure 5-2 to see the hardware used to attach the right Display shelf to the center Display shelf.
Chapter 5 Building the Display Shelf Assembly Building the Display Shelf Assembly, Product ID CTS3K-M Step 5 Attach the screen supports to the accessory cabinets and position, but do not attach, the cabinets to the left and right attachment brackets These screen supports are only required if you use a Type 1 projector screen, part number 800-28681-xx. If your installation uses the projector screen with a product ID of CTS3K-SCREEN and a part number of 74-5416-xx, do not install these brackets.
CH A P T E R 6 Building the Table Assembly Revised: October 31, 2008, OL-14521-01 Parts List Key Part Description Part Number Qty Ctn Notes Table Assembly, Product ID CTS3K-FUR-MAPLE 1 Tabletop leg base 800-28454-xx 3 800-28628-xx (left) 1 41 2 Metal packaging brace 700-24275-xx 4 25 3 Molded foam bumper 800-28625-xx 4 25 4 Tabletop section: right-wing 700-23593-xx 1 45 5 Tabletop section: center-right 700-23594-xx 1 44 6 Tabletop section: center 700-23595-xx 1 44 7 Ta
Chapter 6 Building the Table Assembly Parts List Key Part Description Part Number Qty Ctn Notes Accessory Cabinet 1 Left accessory cabinet 700-23601-xx 1 42, 43 2 M8 x 20 mm screws 48-2273-xx 14 1 3 Not used 4 Right accessory cabinet 700-23601-xx 1 42, 43 Cabinet hole covers 700-26753-xx 14 1 Use these to cover screw mounting holes in the cabinet body.
Chapter 6 Building the Table Assembly Parts List Key Part Description Part Number Qty Ctn Notes 20 I/O modules: power/Ethernet 74-xxxx-xx 6 1 Part number changes per country. Refer to Chapter B, “Appendix B: Region- and Country-Specific Equipment” for the part number.
Chapter 6 Building the Table Assembly Determining the Table Section Type Caution Note Warning In order to prevent scratching the table tops, you should avoid putting any tools on the table surfaces. The directions left and right refer to the assembly as you face it from the front. Table legs are unstable until they are fully attached to the tabletop. Do not use unattached table legs as tabletop supports while you attach tabletop segments. They can fall and cause injury or damage.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-FUR-MAPLE Building the Table Assembly, Product ID CTS3K-FUR-MAPLE Step 1 Remove the Metal packaging braces from the Molded foam bumpers.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-FUR-MAPLE Step 2 Figure 2 Assemble the four Molded foam bumpers and the four Table leg bases. Note The leg base with only one top right attachment bracket is the left-wing leg (see Figure 10). The other three legs each have two attachment brackets. Note Steps for installing all the power and signal cables are in Chapter 7, “Assembling the Remaining Cisco TelePresence Elements.”.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-FUR-MAPLE Step 3 Figure 3 Attach the Right-wing tabletop section to the right Accessory Cabinet bracket.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-FUR-MAPLE Step 4 Figure 4 Attach the right Table segment. a. Cam Lock rods have two adjustable halves that screw into a center piece. Make sure you screw the two halves of the Cam Lock rod equally into the center piece, so both halves are of equal length when inserted into the Cam Lock in each Table segment. b.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-FUR-MAPLE Attach the right-most Table Leg.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-FUR-MAPLE Step 6 Figure 6 Attach the center Table segment. a. Cam Lock rods have two adjustable halves that screw into a center piece. Make sure you screw the two halves of the Cam Lock rod equally into the center piece, so both halves are of equal length when inserted into the Cam Lock in each Table segment. b.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-FUR-MAPLE Step 7 Figure 7 Attach the Right-center Table leg.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-FUR-MAPLE Step 8 Figure 8 Attach the left Table segment. a. Cam Lock rods have two adjustable halves that screw into a center piece. Make sure you screw the two halves of the Cam Lock rod equally into the center piece, so both halves are of equal length when inserted into the Cam Lock in each Table segment. b.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-FUR-MAPLE Step 9 Figure 9 Attach the left center Table leg.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-FUR-MAPLE Step 10 Attach the left-most Table leg. Note Figure 10 The left-most Table leg is different from the other three table legs. It has only one flange on the right side of the leg, to attach to the left Table segment.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-FUR-MAPLE Step 11 Figure 11 Attach the table door.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-FUR-MAPLE Step 12 Using scissors, completely remove one of the four webbed belts from the table hinge safety strap using Figure 12 as a reference; then, install the safety strap and the “please close” label to the table door. When installed, the text on the metal part of the safety strap faces the table and door.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-FUR-MAPLE Step 13 Figure 13 Attach the Accessory cabinets to the left and right attachment brackets and cover the visible screw holes in the cabinet body with the cabinet hole cover.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-M Building the Table Assembly, Product ID CTS3K-M Step 1 Remove the Metal packaging braces from the Molded foam bumpers.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-M Step 2 Assemble the four Molded foam bumpers and the four Table leg bases. Note Figure 15 The leg base with only one top right attachment bracket is the left most table leg (see Figure 25). The other three legs each have two attachment brackets.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-M Step 3 Assemble the I/O modules for the outside left and outside right molded foam bumpers. The outside left and outside right molded foam bumpers only have one I/O module each. The inner molded foam bumpers have two (see Figure 17). Note Steps for routing the Ethernet and power cables are in Chapter 8, “Routing Power and Signal Cables.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-M Step 4 Assemble the I/O modules for the inner molded foam bumpers. Note Steps for routing the Ethernet and power cables are in Chapter 8, “Routing Power and Signal Cables.” Note The flange on the I/O module cover plate is wider on the bottom than on the top.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-M Step 5 Figure 18 Attach the right wing tabletop section to the right Accessory Cabinet bracket.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-M Step 6 Note Figure 19 Attach the right Table segment. a. Make sure you tighten the draw bolt evenly on both sides. b. While a draw bolt is being tightened, hold the table edges together to avoid damage to the draw bolt or the table segment. c. Tighten the draw bolt so the two table segments are connected snugly. d.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-M Step 7 Figure 20 Attach the right most Table Leg.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-M Step 8 Note Figure 21 Attach the center Table segment. a. Make sure you tighten the draw bolt evenly on both sides. b. While a draw bolt is being tightened, hold the table edges together to avoid damage to the draw bolt or the table segment. c. Tighten the draw bolts so the two table segments are connected snugly. d.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-M Step 9 Figure 22 Attach the right center Table leg.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-M Step 10 Note Figure 23 Attach the left Table segment. a. The draw bolts have two halves that screw into a center piece. b. While a draw bolt is being tightened, hold the table edges together to avoid damage to the draw bolt or the table segment. c. Tighten the draw bolts so the two table segments are connected snugly. d.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-M Step 11 Figure 24 Attach the left center Table leg.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-M Step 12 Figure 25 Attach the left most Table leg.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-M Step 13 Attach one microphone to each table segment. There are three microphones for the table. The center microphone cable for the table must be seated in the cable channel on the underside of the center table segment in order to properly install the projector mounting bracket. You can use tape to secure it in place. Note Steps for routing the microphone cables are in Chapter 8, “Routing Power and Signal Cables.”.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-M Step 14 Figure 27 Attach the table door to the tabletop sections and attach the “please close” label to the underside of the table door.
Chapter 6 Building the Table Assembly Building the Table Assembly, Product ID CTS3K-M Step 15 Figure 28 Attach the Accessory cabinets to the left and right attachment brackets and cover the visible screw holes in the cabinet body with the cabinet hole cover. Accessory cabinets 2 1 4 201163 2 Note The Right Accessory Cabinet attachment bracket (marked “4” in the illustration), has a central rectangular hole that differentiates it from the Left Accessory Cabinet attachment bracket.
CH A P T E R 7 Assembling the Remaining Cisco TelePresence Elements Revised: October 31, 2008, OL-14521-01 Parts List Key Part Description Camera and Camera Assembly (Figure 7-1) Part Number Qty Ctn Notes 1 Camera assembly 68-2900-06 1 2 8 M8 x 20 mm screws 48-2273-xx 4 1 Used to attach to the Camera bracket on the center Display structure.
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Key Part Description Ethernet and Power I/O Connections Part Number Qty Ctn 1 I/O blank: large 700-23806-xx 2 1 2 I/O blank: small 700-23807-xx 6 1 3 I/O modules: power/Ethernet 74-xxxx-xx 6 1 4 I/O Module Cover plate 700-23305-xx 4 41 (CTS3K-FUR-MAPLE) 40 (CTS3K-M) 5 10 m Cat6 Ethernet cable, blue 37-0901-xx 6 1 6 3 m Jumper cord 37-0833-xx 9 1 7 M4 nuts 49-0326 20 1 8 M4 x 12 mm screws, bla
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Key Part Description Part Number Qty Ctn 5 M4 x 12 mm screws 48-1045-xx 20 1 6 M4 washers 49-0735-xx 20 1 Notes Audio/Video Extension Unit 1 Mounting bracket for audio/video extension unit 700-26833-xx 1 1 For codecs with a single microphone connection 2 audio/video extension unit 800-30442-xx 1 1 For codecs with a single microphone connection Speaker Assembly 1 Speaker 74-4740-xx 3 7, 8, 9 2 Speake
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Key Part Description Camera Target Assembly Part Number Qty Ctn 1 Tabletop camera target: large 700-24323-xx 1 32 (CTS3K-FUR-MAPLE) 29 (CTS3K-M) 2 Tabletop camera target: small 700-24320-xx 1 32 (CTS3K-FUR-MAPLE) 29 (CTS3K-M) 3 Cardboard ruler 700-24321-xx 1 32 (CTS3K-FUR-MAPLE) 29 (CTS3K-M) 4 Vertical bar 700-23961-xx 2 32 (CTS3K-FUR-MAPLE) 29 (CTS3K-M) 5 Horizontal bar 700-23960-xx 2 32 (CTS3K-FUR-MAPL
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Step 1 Place the assembly over the center display, then attach the Camera Assembly to the Camera Assembly bracket. For clarity, the display has been removed from the illustration in Figure 7-1. Note Figure 7-1 There are two foam pads on inside of the camera assembly.
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Step 2 Attach the Microphones to the left, right, and center Table segments. The center Microphone cable must be seated in the cable channel on the underside of the center Table segment in order to properly install the Projector mounting bracket. You can use tape to secure it in place.
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Step 3 Assemble the I/O Modules for the outside left and outside right Molded Foam bumpers. The outside left and outside right Molded Foam bumpers only have one I/O Module each. The inner Molded Foam bumpers have two (see Figure 7-4).
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Step 4 Assemble the I/O Modules for the two inner Molded Foam bumpers. The outside left and outside right Molded Foam bumpers only have one I/O Module each (see Figure 7-3). The inner Molded Foam bumpers have two.
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Step 5 Attach the Projector to the Projector mounting bracket.
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Step 6 Figure 7-6 Attach the Projector mounting bracket to the underside of the center Table segment. a. Insert the screws and washers in the underside of the center Table segment to prepare for attaching the Projector mounting bracket; then, slide the bracket between the two rows of screws. b.
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Step 7 Attach the VGA module to the center Table segment. The VGA module supports the VGA peripheral cable when not in use.
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Step 8 Figure 7-8 Attach the center Privacy panel.
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Step 9 Figure 7-9 Attach the left Privacy panel.
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Step 10 Figure 7-10 Attach the right Privacy panel.
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Step 11 Attach the right-wing Privacy panel.
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Step 12 Attach the Cable management bars to the three Codecs.
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Step 13 Attach the Codec attachment brackets to the three Codecs.
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Step 14 Note Attach the three Codecs to the Display structure Front foot stabilizers. If you ordered a Presentation Codec with your TelePresence system, refer to the Cisco TelePresence Hardware Options and Upgrade Guide for instructions to install your presentation codec.
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Step 15 • If your codec has one microphone connection, complete the following steps to install the audio/video expansion unit. See Figure 8-8 for an example of this type of codec. • If your codec has three microphone connections, continue to Step 16. See Figure 8-7 for an example of this type of codec. You do not need to install the audio/video expansion unit. a. Attach the audio/video extension unit to its bracket.
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List b. Audio/Video Extension Unit 35 204147 Figure 7-16 Attach the audio/video extension unit to the rear of the display assembly.
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Step 16 Attach the Speaker board brackets and Leveling feet to the Speaker boards. The Speaker board brackets should angle towards the rear of the Display structure.
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Step 17 Figure 7-18 Attach the Speaker boards to the Speaker board brackets on the underside of the Display shelves.
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Step 18 Attach the Speakers to the Speaker boards.
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Step 19 Attach the Projector screen to the Projector clips on the underside of the Display shelves. Note Figure 7-20 Please refer to your Cisco TelePresence Projector Screen Assembly manual for the exact procedures used to build the projector screen. The Projector Screen Assembly manual is included in the projector screen carton.
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Step 20 Auxiliary Control Unit 35 1 204148 Figure 7-21 Attach the auxiliary control unit to its bracket using 5 mm screws; then, attach the unit and bracket to the rear of the display assembly.
Chapter 7 Assembling the Remaining Cisco TelePresence Elements Parts List Step 21 Assemble the Large Camera Target. When you slide the Camera target into the frame, make sure the target is centered in the frame between the vertical lines at the top and bottom of the target.
CH A P T E R 8 Routing Power and Signal Cables Revised: October 31, 2008, OL-14521-01 Parts List Key Part Description Part Number Qty Ctn 1 Power distribution units 74-4787-01 4 1 2 Speaker cable 37-0849-01 3 1 3 8 m DVI-to-VGA + audio cable 37-0848-01 1 1 4 6 m video cable 37-0854-01 1 1 5 3 m (black) Cat6 Ethernet cable 37-0877-01 5 1 6 10 m Cat6 Ethernet cable, blue 37-0901-01 2 1 7 7 m power cord 37-xxxx-xx 1 10 8 3 m Jumper cord 37-0833-01 9 1 9 2 m Jump
Chapter 8 Routing Power and Signal Cables Parts List Warning Caution Output receptacles cannot exceed 15A for any one receptacle. Correct routing of the various power cords to the appropriate PDU is critical for the safety and success of the Cisco TelePresence System 3200 assembly. Each PDU is routed to a different 20A circuit to prevent circuit overload when all the electrical components are properly installed.
Chapter 8 Routing Power and Signal Cables Parts List Step 1 Attach the two left Power Distribution Units (PDU) to the left Accessory cabinet. The accessory cabinets each have screw holes for two PDUs on one side wall and screw holes for one PDU on the other. When the cabinets are correctly oriented with each door opening out to the side, the right cabinet has the single-PDU side facing the rear wall, and the left cabinet has the double-PDU side facing the rear wall.
Chapter 8 Routing Power and Signal Cables Parts List Step 2 Attach the right PDU to the right Accessory cabinet. The accessory cabinets each have screw holes for two PDUs on one side wall and screw holes for one PDU on the other. When the cabinets are correctly oriented with each door opening out to the side, the right cabinet has the single-PDU side facing the rear wall, and the left cabinet has the double-PDU side facing the rear wall.
Chapter 8 Routing Power and Signal Cables Parts List Step 3 Figure 8-3 Attach the center PDU to the center privacy panel. Table assembly PDU attachment to the center Privacy panel 201184 1 Note The PDU power cable should extend from the right side.
Chapter 8 Routing Power and Signal Cables Parts List Step 4 Figure 8-4 Route the power cables for the table leg foam bumper I/O modules and the projector. Routing Power Cables for I/O Modules and Projector CISCO IP PHONE 7970 TelePresence 1 4 GHI 7 PQRS 3 2 ABC 5 JKL 8 TUV 0 DEF 6 MNO 9 WXYZ # 8 Table Leg Power 9 Projector Power 201204 OPER Note The six jumper cords from the I/O modules in the table legs route to the center PDU.
Chapter 8 Routing Power and Signal Cables Parts List Step 5 Figure 8-5 Route the signal cables from the table assembly.
Chapter 8 Routing Power and Signal Cables Parts List Step 6 Note Figure 8-6 Connect the Cisco Unified IP Phone, VGA peripheral, and projector HD video cables. The VGA Peripheral cable is the free-hanging cable resting in the VGA module attached to the center Table segment.
Chapter 8 Routing Power and Signal Cables Parts List Step 7 Connect the microphone cables. • If you have a codec with three microphone outputs, connect the microphones using Figure 8-7 as a guide. Cable the microphones using the following markings and colors on the codec: – A single dot on a green background indicates a center microphone. – Two dots on a white background indicate a left microphone. Note The directions left and right refer to the assembly as you face it from the front.
Chapter 8 Routing Power and Signal Cables Parts List Figure 8-7 Connecting the Microphones For a Three-Microphone Outlet Codec CISCO IP PHONE 7970 TelePresence 1 4 GHI 7 PQRS 3 2 ABC 5 JKL 8 TUV 0 DEF 6 MNO 9 WXYZ # 205771 OPER 14 Microphones Cisco TelePresence System 3000 8-10 OL-14521-01
Chapter 8 Routing Power and Signal Cables Parts List Connecting the Microphones for a Codec with One Microphone Outlet and an Audio/Video Extension Unit 205760 Figure 8-8 Cisco TelePresence System 3000 OL-14521-01 8-11
Chapter 8 Routing Power and Signal Cables Parts List Step 8 Connect the speaker cables using the following markings and colors on the codec: • A single dot on a green background indicates a center speaker. • Two dots on a white background indicate a left speaker. • Three dots on a red background indicate a right speaker. Figure 8-9 shows the speaker cabling. Left and right are reversed.
Chapter 8 Routing Power and Signal Cables Parts List Step 9 Figure 8-10 Connect the following cables: • Attach and route the power cables for the lighting assembly by connecting the lights to the auxiliary control unit. • Connect the serial cable between the projector and the auxiliary control unit. • Connect the Ethernet cables between the codec and the auxiliary control unit. • Connect the power cord for the auxiliary control unit to a wall outlet.
Chapter 8 Routing Power and Signal Cables Parts List Step 10 Cabling the Plasma displays Signal Power 201186 Figure 8-11 Connect the plasma display cables. Note Figure 8-11 displays the rear view of the Cisco TelePresence System 3200. Left and right are reversed. Tip Before you plug cables into a Codec or PDU, label each cable.
Chapter 8 Routing Power and Signal Cables Parts List Step 11 Cabling the Camera assembly 5 10 RJ45 Power over Ethernet 201188 Figure 8-12 Connect the camera assembly cables. HDMI connector Note The camera cluster can experience radio frequency interference issues if the camera Ethernet and video cables are routed, bundled, or tied together. Cisco recommends that you route the Ethernet and video cables separately and use cable ties to tie them to opposite sides of the frame.
Chapter 8 Routing Power and Signal Cables Parts List Step 12 Note Figure 8-13 Connect the codec signal cables. If you ordered a Presentation Codec or Auxiliary Control Unit with your TelePresence system, refer to the Cisco TelePresence Hardware Options and Upgrade Guide for cabling instructions.
Chapter 8 Routing Power and Signal Cables Parts List Step 13 Figure 8-14 Connect the codec power cables.
Chapter 8 Routing Power and Signal Cables Parts List Step 14 Figure 8-15 (Optional) If your installation uses an optional external display or a document camera, install and route the cabling.
Chapter 8 Routing Power and Signal Cables Parts List Step 15 (Optional) If your installation uses an external display or a document camera with a presentation codec, install and route the cabling. Refer to the “Options for the Cisco TelePresence System 3000” chapter of the Cisco TelePresence Hardware Options and Upgrade Guide for more information about the presentation codec.
Chapter 8 Routing Power and Signal Cables Parts List Cisco TelePresence System 3000 8-20 OL-14521-01
CH A P T E R 9 First-Time Setup Revised: February 6, 2009, OL-14521-01 After you have assembled the Cisco TelePresence System (CTS), you set up the individual system components (such as displays and cameras) using Hardware Setup, located under Troubleshooting in the CTS Administration software.
Chapter 9 First-Time Setup Loading CTS Administration Software Note Make sure that you power on all codecs within 30 seconds to avoid power on detection failure. After you turn on the codecs, the displays associated with each codec becomes active. CTS displays green check marks on all displays to show bootup progress. Bootup is complete when the system displays six check marks as shown in Figure 9-1.
Chapter 9 First-Time Setup Loading CTS Administration Software Figure 9-2 System IP Address Note Note If the IP address that displays is 192.168.100.2, the CTS-3000 could not contact the DHCP server or your system does not use DHCP. If your network does not use DHCP, navigate to Configuration > IP Settings, change the DHCP Enabled setting to No, and specify a static IP address, subnet mask, gateway and DNS server. Step 2 After successful bootup, the CTS Administration Software loads.
Chapter 9 First-Time Setup Configuring an Alternate TFTP Server (Optional) Step 5 Note From the Cisco IP telephone welcome page, press Next. The system reboots. The system might reboot several times during the initial startup process. Step 6 Open a browser on a computer that is connected to the network. Step 7 In the URL field, type the IP address that you obtained in Step 3 and press Enter. The browser launches Cisco TelePresence System Administration.
Chapter 9 First-Time Setup Setting Up CTS Components Step 2 From Troubleshooting, choose Hardware Setup to initially set up the components in the Cisco TelePresence system.
Chapter 9 First-Time Setup Setting Up CTS Components Troubleshooting Displays Use Table 9-1 to troubleshoot problems with the images on the displays. Table 9-1 Troubleshooting Chart for Display Problems Problem Cisco TelePresence 3000/3200 only Power-on test indicates the displays turn on in the wrong sequence. The normal power on sequence is the left, center, then right display screen. No image.
Chapter 9 First-Time Setup Setting Up CTS Components Setting Up the Cameras The cameras are set up correctly when images are centered and in focus on the display screens and the white balance has been configured. The hardware setup software provides a camera Auto Adjust feature and a way to use targets to fine-tune the camera’s focus. Attach the Camera Target Two camera targets are provided with the Cisco TelePresence system: a large white target and a smaller target.
Chapter 9 First-Time Setup Setting Up CTS Components Note Figure 9-3 If one of the left/right screws is covered by the camera cable, use the other screw to make all left/right adjustments.
Chapter 9 First-Time Setup Setting Up CTS Components Figure 9-4 Correct Camera Target Alignment—Center Display Red plus sign within black cross Note curved lines touching screen border 205764 Red lines Figure 9-5 Table edge Correct Camera Target Alignment—Right Display Red Vertical line Red plus sign within black cross 205765 Red lines Table edge Cisco TelePresence System 3000 OL-14521-01 9-9
Chapter 9 First-Time Setup Setting Up CTS Components Figure 9-6 Correct Camera Target Alignment—Left Display Red Vertical line Red plus sign within black cross 205766 Red lines • Click Hide Camera Target to remove the alignment images. • Click Done when you complete the adjustment. Table edge Show All Camera Targets • Click Show All Camera Targets to align each camera independent of the other cameras.
Chapter 9 First-Time Setup Setting Up CTS Components Figure 9-7 Attaching the Camera Hood Assembly 7 2 1 3 201203 7 Cisco TelePresence System 3000 OL-14521-01 9-11
Chapter 9 First-Time Setup Setting Up CTS Components Troubleshooting Cameras Use Table 9-2 to troubleshoot problems with cameras. Table 9-2 Troubleshooting Chart for Camera Problems Problem Cisco TelePresence 3000/3200 only Camera image appears on the wrong display. Possible Cause Action Cables are plugged into the wrong connector ports. Check that the cables from each camera are plugged into the correct connector on its respective codec.
Chapter 9 First-Time Setup Setting Up CTS Components Setting Up the Speakers The speakers are set up correctly you can hear sound clearly from each one. You can choose whether you want to cycle through the speakers automatically or manually. • Click Speakers on the Hardware Setup window to select the speaker test. • Click Start to begin the speaker setup. • Click Cycle Through Speakers to have sound cycled automatically for 5 seconds on each speaker.
Chapter 9 First-Time Setup Setting Up CTS Components microphones per screen, depending on the number of microphones installed. The top microphone represents the microphone in the front row; the bottom microphone icons represent the back row microphones. • Click Microphones on the Hardware Setup window. • Click Start to begin setup. • Lightly tap each microphone and watch the audio meter on the corresponding display screen to see that sound registers.
Chapter 9 First-Time Setup Setting Up CTS Components Setting Up the Projector This section contains the steps that you perform to set up the projector and includes the following sections: • Standard CTS-3000 Projector Setup, page 9-15 • Projector Setup With an Auxiliary Control Unit, page 9-19 Standard CTS-3000 Projector Setup To set up a projector with a standard CTS-3000 installation, complete the following steps: Note Step 1 Note The following procedures are specific to the Sanyo PLV-Z4 and PLV
Chapter 9 First-Time Setup Setting Up CTS Components Step 3 Set the display to display right-side up by completing the following steps: a. Note Press the MENU key on the remote control. The menu screen will appear upside down and reversed. If the image is right-side up, continue to Step 4. b. Use the Up Arrow and Down Arrow keys and highlight Setting. c. Press the Right Arrow key and select Setting to enter the Setting submenu. d. Press the Up Arrow and Down Arrow keys and select Advanced Menu.
Chapter 9 First-Time Setup Setting Up CTS Components Step 9 Step 10 d. Press the Right Arrow key and select Normal. e. Press the Left Arrow key to confirm your selection. Eliminate overscan by completing the following steps: a. Press the Up Arrow and Down Arrow keys and highlight Picture adj. b. Press the Right Arrow key and select Picture adj. to enter the Picture Adjustment submenu. c. Press the Right Arrow key and select Overscan. d.
Chapter 9 First-Time Setup Setting Up CTS Components Step 12 Step 13 Select the screen size by completing the following steps: a. From the main menu, use the Up Arrow and Down Arrow keys to highlight the Screen function. Press the Right Arrow key to select the Screen sub-menu. b. Use the up and Down Arrow keys to select Normal, then press OK. c. Press the Left Arrow key to return to the main menu. Select the video source by completing one of the following procedures: a.
Chapter 9 First-Time Setup Setting Up CTS Components If the input image is displaying correctly, you should see an image projected on the projection surface. Step 17 If the image is out of focus or is too small, use the projector focus ring to focus the image and use the zoom lever to create the largest possible image. Step 18 Click Stop in Cisco TelePresence System Administration to remove the test pattern and complete the projector test.
Chapter 9 First-Time Setup Setting Up CTS Components Step 6 c. Press OK until the group number setting changes to 100. d. Press the Down Arrow key until the No. setting changes to 4. e. Press the Left Arrow key until the Data setting changes to 0. f. Press the ON-OFF key to end the service menu. Center the projector display within the screen by completing the following steps: a. Locate the lock switch and two dials on the side of the projector. b. Move the switch to the unlock position. c.
Chapter 9 First-Time Setup Setting Up CTS Components Troubleshooting Presentation Devices Use Table 9-5 to troubleshoot problems with presentation devices. Table 9-5 Troubleshooting Chart for Presentation Device Problems Problem Possible Cause Possible Solution Test pattern is not displayed. Projector power switch is off. Check projector power switch. Switch the projector on/off rocker switch to the ON position. Test pattern is not displayed. Power cable is not connected.
Chapter 9 First-Time Setup Setting Up CTS Components Note The Cisco TelePresence System can display information from multiple input devices during a meeting; if multiple input devices are sending information, the projector displays the input from the last presentation device sending information.
CH A P T E R 10 Use & Care Guide Revised: October 31, 2008, OL-14521-01 Maintaining the Tabletop Caution Waxing or rubbing the surface with any type of abrasive is not recommended. • For general daily care - use a dampened cloth with clean water. • To remove dirt - use a mild soap and water solution. Wipe off with clean water afterward to remove the soap. • To remove ink marks - rub the stained area with a pencil eraser. • To polish the tabletop - use lemon oil.
Chapter 10 Use & Care Guide Maintaining the Projector Maintaining the Projector Note Refer to the Projector User Guide included with your projector for maintenance issues such as cleaning the projector lens. To replace the projector lamp, see the “Replacing the Projector Lamp—Part Number CTS-PRJTR-BL-GEN1” section on page 11-17. Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
CH A P T E R 11 Field-Replaceable Unit Guide Revised: October 31, 2008, OL-14521-01 This chapter describes the steps you perform to replace the field-replaceable units (FRUs) for the Cisco TelePresence system and includes the following sections: • Replacing the Camera Cluster—Part Number CTS3K-CAM-CLST-G2, page 11-1 • Replacing a Plasma Display—Part Number CTS-DISP-65-GEN2, page 11-3 • Replacing a Speaker—Part Number CTS-LDSPKR, page 11-8 • Replacing a Codec Unit—Part Number CTS-CODEC-PRI-G2 (Prim
Chapter 11 Field-Replaceable Unit Guide Replacing the Camera Cluster—Part Number CTS3K-CAM-CLST-G2 • The Release Notes for Cisco TelePresence System for your software release • Power screwdriver with 2.5, 3, and 6 mm (standard or round) Allen bits, or standard 2.5, 3, and 6 mm Allen wrenches • 0.
Chapter 11 Field-Replaceable Unit Guide Replacing a Plasma Display—Part Number CTS-DISP-65-GEN2 Step 6 Reattach the Ethernet and signal cables according to your temporary markings. Do not attach the camera hoods at this time. Step 7 Open a browser on a computer connected to the network. Step 8 Type in the IP address of the center, primary codec unit. Enter the required information at the login screen. Step 9 The Cisco TelePresence Administrator window appears.
Chapter 11 Field-Replaceable Unit Guide Replacing a Plasma Display—Part Number CTS-DISP-65-GEN2 Cisco TelePresence 3000 Structure, Accessory, and Adjustment Assembly: • Tip Power screwdriver with 2.5, 3, and 6 mm (standard or round) Allen bits, or standard 2.5, 3, and 6 mm Allen wrenches A round-head Allen bit allows the bit to work at an angle instead of only straight out, which is helpful in tight spots.
Chapter 11 Field-Replaceable Unit Guide Replacing a Plasma Display—Part Number CTS-DISP-65-GEN2 • If your projector screen does not have side trims and is flush with the display cabinet, grasp the outer edges of the screen and pull it up and away from the Projector clips that hold the screen to the Display shelves. Step 15 Disconnect the Speaker cables from the Speaker terminals. Step 16 Loosen the half-turn bolts on either side of the left Speaker board.
Chapter 11 Field-Replaceable Unit Guide Replacing a Plasma Display—Part Number CTS-DISP-65-GEN2 Step 3 Loosen each cam lock coupling. Step 4 Unscrew the left Display shelf from the two Display Shelf support brackets. Step 5 Pull the left Display shelf away from the center Display shelf and set aside. Step 6 If you are replacing the left Plasma display, skip to the next section, “Removing the Display Screen and Completing the Procedure”.
Chapter 11 Field-Replaceable Unit Guide Replacing a Plasma Display—Part Number CTS-DISP-65-GEN2 See Chapter 3, “Mounting and Leveling the Plasma Displays”. Step 13 If required, attach the camera cluster. See Chapter 7, “Assembling the Remaining Cisco TelePresence Elements” and Chapter 8, “Routing Power and Signal Cables”. Step 14 Reassemble the display shelf sections. See Chapter 5, “Building the Display Shelf Assembly”. Step 15 Hang the speaker boards.
Chapter 11 Field-Replaceable Unit Guide Replacing a Speaker—Part Number CTS-LDSPKR Replacing a Speaker—Part Number CTS-LDSPKR Required Information, Tools, and Equipment To remove and replace a speaker for the Cisco TelePresence 3000, you need the following information, tools, and equipment: • The Cisco TelePresence System Administrator's Guide for your software release • Power screwdriver with 2.5, 3, and 6 mm (standard or round) Allen bits, or standard 2.
Chapter 11 Field-Replaceable Unit Guide Replacing a Speaker—Part Number CTS-LDSPKR c. After you have created a gap of approximately 1/2 inch (1 centimeter) between the screen and the display shelf, detach the holes on the top screen from the locating pins on the underside of the display shelves and remove the screen.
Chapter 11 Replacing a Codec Unit—Part Number CTS-CODEC-PRI-G2 (Primary Codec) or CTS-CODEC-SEC (Secondary Codec) Field-Replaceable Unit Guide Replacing a Codec Unit—Part Number CTS-CODEC-PRI-G2 (Primary Codec) or CTS-CODEC-SEC (Secondary Codec) Required Information, Tools, and Equipment To remove and replace a codec unit for the Cisco TelePresence 3000, you need the following information, tools, and equipment: • The Cisco TelePresence System Administrator's Guide for your software release • Power scre
Chapter 11 Field-Replaceable Unit Guide Replacing a Codec Unit—Part Number CTS-CODEC-PRI-G2 (Primary Codec) or CTS-CODEC-SEC (Secondary Codec) See Chapter 7, “Assembling the Remaining Cisco TelePresence Elements” for additional information. Step 5 Remove the codec from the Display structure. Step 6 Remove the L brackets from the codec. See Chapter 7, “Assembling the Remaining Cisco TelePresence Elements” for additional information. Step 7 Remove the cable management bar from the codec.
Chapter 11 Field-Replaceable Unit Guide Replacing a Microphone—Part Number CTS-MIC Replacing a Microphone—Part Number CTS-MIC Required Information, Tools, and Equipment To remove and replace a microphone for the Cisco TelePresence 3000, you need the following information, tools, and equipment: • The Cisco TelePresence System Administrator's Guide for your software release • Power screwdriver with 2.5, 3, and 6 mm (standard or round) Allen bits, or standard 2.
Chapter 11 Field-Replaceable Unit Guide Replacing a Microphone—Part Number CTS-MIC Step 5 If you are replacing the center microphone, follow these steps. a. Loosen, but don’t remove, the mounting screws holding the projector assembly to the underside of the center tabletop. b. Remove the projector assembly by sliding the unit to the left and away from the mounting screws. c. Alternately, if the fit is too tight to remove in this manner, remove the mounting screws from the tabletop.
Chapter 11 Field-Replaceable Unit Guide Replacing a Light Fixture—Part Number CTS-LIGHT-FIXT Replacing a Light Fixture—Part Number CTS-LIGHT-FIXT Required Information, Tools, and Equipment To disassemble and reassemble portions of the Cisco TelePresence 3000, you need the following information, tools, and equipment: • Cisco TelePresence System Release 1.4 Administrator’s Guide, OL-13676-03 • Power screwdriver with 2.5, 3, and 6 mm (standard or round) Allen bits, or standard 2.
Chapter 11 Field-Replaceable Unit Guide Replacing the Audio/Video Extension Unit—Part Number CTS-AV-EXP Step 3 Step 4 Step 5 For the right and left vertical light fixtures, follow these steps. a. Remove the screws from the light fixture holding bracket. The bracket is located in the middle of the fixture. Retain the screws. b. Lift the light fixture up and out of the lower cup bracket. For the horizontal light fixtures, follow these steps. a.
Chapter 11 Field-Replaceable Unit Guide Replacing the Audio/Video Extension Unit—Part Number CTS-AV-EXP Step 6 Power on the system by turning the power switches to the On position on the two left PDUs, single right PDU, and (if present) auxiliary control unit or PDU on the rear center of the display assembly. Step 7 Test the microphone by performing the procedures in the “Setting Up the Microphones” section on page 9-13.
Chapter 11 Field-Replaceable Unit Guide Replacing the Cisco IP Phone—Part Number CP-7975G-CTS Replacing the Cisco IP Phone—Part Number CP-7975G-CTS Step 1 Open a browser on a computer connected to the network. Step 2 Type in the IP address of the Cisco Unified Communications Manager. Enter the required information at the login screen. Step 3 Go to Device>Phone and find the phone you are replacing.
Chapter 11 Field-Replaceable Unit Guide Replacing the Projector Lamp—Part Number CTS-PRJTR-BL-GEN1 Note You might have to remove the screws and remove the assembly during this step, rather than loosen the screws. Be sure to secure the projector when you remove the screws. c. Remove the projector assembly by sliding the unit to the side until the projector mounting bracket disengages from the loosened mounting screws.
Chapter 11 Field-Replaceable Unit Guide Replacing the Projector—Part Number CTS-PRJTR-GEN1 Replacing the Projector—Part Number CTS-PRJTR-GEN1 Step 1 Power off the projector by turning off the power switch located on the back of the unit. Step 2 Unplug the VGA cable from the back of the unit. Step 3 Unplug the power cable from the back of the unit. Step 4 Remove two of the six screws that hold the projector assembly to the underside of the center tabletop.
Chapter 11 Field-Replaceable Unit Guide Replacing a PDU—Part Number CTS-PWR-PDU Replacing a PDU—Part Number CTS-PWR-PDU There are two PDUs attached to the left accessory cabinet, one attached to the right accessory cabinet, one PDU attached to the underside of the tabletop, and one attached to the center display structure. Step 1 On the PDU to be replaced, turn the power switch to Off and remove the plug from the wall receptacle. Step 2 Remove any cables plugged into the PDU.
Chapter 11 Field-Replaceable Unit Guide Replacing the Auxiliary Control Unit—Part Number CTS-LIGHT-CTRL Replacing the Auxiliary Control Unit—Part Number CTS-LIGHT-CTRL The auxiliary control unit is located in the center of the display assembly. For more information about the auxiliary control unit, refer to the “Options for the Cisco TelePresence System 3000” chapter of the Cisco TelePresence Hardware Options and Upgrade Guide.
Chapter 11 Field-Replaceable Unit Guide Replacing a Display Shelf Note Make sure to retain all screws, connectors, and other parts during the disassembly.
Chapter 11 Field-Replaceable Unit Guide Replacing a Table Top Section Caution Tip Make sure that all remaining shelves stay on the display structure and do not fall between the structure supports. Slide the shelves to the left; there is space on the left that is created by the open table door. Step 10 Remove the splines from the slot at both edges of the shelf to be replaced. Step 11 Place the new shelf on the display assembly. Step 12 Place the splines in the slots at the edges of the new shelf.
Chapter 11 Field-Replaceable Unit Guide Replacing a Table Top Section Removing and Replacing a Table Top Section Step 1 Open the table door. Step 2 Perform the following actions for specific table top sections: • If you are replacing the table door or the left-center table top section, remove the table door. See Figure 11 for an exploded diagram of the parts for the door. • If you are replacing the center table top section, remove the projector.
Chapter 11 Field-Replaceable Unit Guide Replacing a Table Top Section Step 18 Insert the draw bolts and tighten them between the new table top section and the adjoining table top sections. See Chapter 6, “Building the Table Assembly” for the location of the draw bolts. Step 19 Attach the legs to the table top sections with the screws. See Chapter 6, “Building the Table Assembly” for the location of the table legs and screw attachment locations.
Chapter 11 Field-Replaceable Unit Guide Replacing a Table Top Section Cisco TelePresence System 3000 11-26 OL-14521-01
A P P E N D I X A Appendix A: Parts List Sorted by Carton Revised: October 31, 2008, OL-14521-01 Overview • Each carton may contain multiple parts. Some of these parts are grouped together in kits. Each kit is a smaller box contained within the ‘master’ carton. • Each kit box is identified with an ID number. • If the kit box also contains boxes or bags, each one is identified with an ID number.
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-FUR-MAPLE Table Shelf and Table Section Assemblies Sub-Kit ID Kit ID Number Number Part Description 78-17792-02 Cisco TelePresence Meeting Quick Reference document N/A 78-17795-02 Cisco TelePresence 3000 Assembly, Use & Care, 1 and Field Replacement Unit Guide (pointer to online document) N/A 78-17839-04 Regulatory Compliance and Safety Information 1 N/A 79-0087-02 ESD wrist strap 1 N/A 700-23825-03 Table hinge safe
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-FUR-MAPLE Table Shelf and Table Section Assemblies Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference N/A 74-xxxx-xx I/O modules: power/Ethernet 6 Chapter 7 Refer to Appendix B for specific part numbers.
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-FUR-MAPLE Table Shelf and Table Section Assemblies Carton 5 of 47: Secondary Codec, 800-28202-xx, CTS-CODEC-SEC Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 53-2907-01 48-1962-01 M5 x 12 mm screws 2 Chapter 7 700-23449-xx Cable management bar 1 Chapter 7 68-2898-xx Secondary Codec 1 Chapter 7 N/A Carton 6 of 47: Projector, 74-4824-xx, CTS-PRJTR-GEN1 Sub-Kit ID Kit I
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-FUR-MAPLE Table Shelf and Table Section Assemblies Carton 10 of 47: Power Cord, 37-08xx-xx, PWR-CORD10-xx Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference N/A 37-xxxx-xx Power cord 6 Chapter 8 Refer to “Appendix B: Region- and Country-Specific Equipment” for specific part numbers.
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-FUR-MAPLE Table Shelf and Table Section Assemblies Carton 14 of 47: Front Foot Stabilizer, 69-1624-xx, CST3K-STRUCTURE Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 69-1624-xx 700-23359-xx Front foot stabilizer 2 Chapter 2 Carton 15 of 47: Front Foot Stabilizer, 69-1624-xx, CST3K-STRUCTURE Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-FUR-MAPLE Table Shelf and Table Section Assemblies Carton 19 of 47: Auxiliary Control Unit, CTS-LIGHT-CTRL, 74-5405-01 Kit ID Number Sub-Kit ID Number Part Number Part Description Qty Chapter Parts List Reference 74-5405-01 Auxiliary Control Unit 1 Chapter 7 Carton 20 of 47: Plasma Display, 74-4881-xx, CTS-DISP-65-GEN2 Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 74-460
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-FUR-MAPLE Table Shelf and Table Section Assemblies Carton 24 of 47: Projector Bracket, 69-1631-xx, CTS3K-STRUCTURE Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 69-1631-xx 48-1963-01 M6 x 10 mm screws 4 Chapter 7 700-23824-xx Projector mounting bracket 1 Chapter 7 Carton 25 of 47: Foam Bumpers, 69-1634-xx, CTS3K-STRUCTURE Sub-Kit ID Kit ID Number Number Part Number Part
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-FUR-MAPLE Table Shelf and Table Section Assemblies Sub-Kit ID Kit ID Number Number 69-1615-xx 69-1657-xx Part Number Part Description Qty Chapter Parts List Reference 700-23752-xx Support struts 6 Chapter 4 700-25050-01 Diffuser Panel braces / H-clips 3 Chapter 4 48-2274-01 M8 x 70 mm screws 10 Chapter 4 48-2285-01 M8 x 12 mm flat-head screws 10 Chapter 4 49-1165-01 M8 washers 10 Chapter 4 48-2273-01 M8 x
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-FUR-MAPLE Table Shelf and Table Section Assemblies Carton 31 of 47: Light Fixture, 74-5362-xx, CTS-LIGHT-FIXT Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 74-5362-xx 74-5362-01 CTS-Light-Fixt 1 Chapter 4 Carton 32 of 47: Camera Target, 69-1674-xx, CTS-CAM-TOOL Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 69-1674-xx 700-2
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-FUR-MAPLE Table Shelf and Table Section Assemblies Carton 36 of 47: Display Structure, 69-1622-xx, CTS3K-STRUCTURE Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 69-1622-xx 700-23358-xx Display structure 1 Chapter 2 Carton 37 of 47: Display Structure, 69-1622-xx, CTS3K-STRUCTURE Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 6
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-FUR-MAPLE Table Shelf and Table Section Assemblies Carton 41 of 47: Tabletop Leg Base, 69-1620-xx, CTS3K-STRUCTURE Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 69-1620-xx 700-23305-01 I/O Module Cover plate 1 Chapter 7 800-28454-xx Tabletop leg base 3 Chapter 6 800-28628-xx Tabletop leg base, left 1 Chapter 6 69-1636-xx Carton 42 of 47: Accessory Cabinet, 69-1637-xx
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-M Table Shelf and Table Section Assemblies Carton 45 of 47: Tabletop, 69-1639-xx, CTS3K-FUR-MAPLE Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 69-1639-xx 700-23593-xx Tabletop section: right-wing 1 Chapter 6 700-23597-xx Tabletop section: left door 1 Chapter 6 Carton 46 of 47: Display Shelf, 69-1640-xx, CTS3K-FUR-MAPLE Sub-Kit ID Kit ID Number Number Part Number Part De
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-M Table Shelf and Table Section Assemblies Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 37-0854-01 6 m video cable 1 Chapter 8 37-0887-02 3 m Cat6 Ethernet cable, black 5 Chapter 8 37-0901-01 10 m Cat6 Ethernet cable, blue 4 Chapter 7, 8 47-21524-01 Compliance sticker for plasma display 3 Chapter 8 51-4582-02 Cable identification stickers 3 Chapter 8 78-17792-
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-M Table Shelf and Table Section Assemblies Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference CP-7975GCTS 68-3309-01 Cisco IP Phone 7975G 1 Chapter 7 N/A 69-1691-01 VGA Module 1 Chapter 7 N/A 74-4743-01 Microphones 3 Chapter 7 N/A 74-4787-01 Power distribution units 5 Chapter 8 N/A 74-xxxx-xx I/O modules: power/Ethernet 6 Chapter 7 See “Appendix B: Region- and Co
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-M Table Shelf and Table Section Assemblies Sub-Kit ID Kit ID Number Number N/A Part Number Part Description Qty Chapter Parts List Reference 700-23449-xx Cable management bar 1 Chapter 7 68-2898-xx Secondary Codec 1 Chapter 7 Carton 5 of 44: Secondary Codec, 800-28202-xx, CTS-CODEC-SEC Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 53-2907-01 48-1962-01 M5 x 12 mm sc
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-M Table Shelf and Table Section Assemblies Carton 9 of 44: Speaker, 74-4740-xx, CTS-LDSPKR Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 74-4740-xx 74-4740-01 High-Fidelity Loudspeaker 1 Chapter 7 Carton 10 of 44: Power Cord, 37-08xx-xx, PWR-CORD10-xx Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference N/A 37-xxxx-xx Power cord
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-M Table Shelf and Table Section Assemblies Carton 13 of 44: Privacy Panel, Right, 69-1628-xx, CTS3K-STRUCTURE Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 69-1628-xx 700-23362-xx Privacy panel: right-wing 1 Chapter 7 Carton 14 of 44: Front Foot Stabilizer, 69-1624-xx, CST3K-STRUCTURE Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Refe
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-M Table Shelf and Table Section Assemblies Carton 18 of 44: Accessory Cabinet Brackets, 69-1630-xx, CTS3K-STRUCTURE Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 69-1630-xx 700-23336-xx Left accessory cabinet attachment bracket 1 Chapter 5 700-23337-xx Right accessory cabinet attachment bracket 1 Chapter 5 Carton 19 of 44: Auxiliary Control Unit, CTS-LIGHT-CTRL, 74-5405-01
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-M Table Shelf and Table Section Assemblies Carton 23 of 44: Lighting Assembly, 69-1612-xx, CTS3K-LIGHT-STR Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 69-1612-xx 700-23731-xx Reflector top: center 1 Chapter 4 700-23734-xx Reflector top: top side 2 Chapter 4 700-23735-xx Reflector top: end 2 Chapter 4 700-23737-xx Light “cup” bracket 2 Chapter 4 700-23745-xx Pla
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-M Table Shelf and Table Section Assemblies Carton 25 of 44: Light Fixture, 74-5361-xx, CTS-LIGHT-FIXT Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 74-5361-xx 74-5361-01 CTS-Light-Fixt 1 Chapter 4 Carton 26 of 44: Light Fixture, 74-5361-xx, CTS-LIGHT-FIXT Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 74-5361-xx 74-5361-01
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-M Table Shelf and Table Section Assemblies Carton 30 of 44: Display Structure Crossbars, 69-1623-xx, CTS3K-STRUCTURE Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 69-1623-xx 700-23361-xx Support crossbars 4 Chapter 2 Carton 31 of 44: Privacy Panels, 69-1629-xx, CTS3K-STRUCTURE Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 6
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-M Table Shelf and Table Section Assemblies Carton 35 of 44: Spare Fluorescent Bulbs for Light Fixture, 74-5232-xx, CTS-3000-SPR-BULBS Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 74-5232-01 95-9611-01 Spare lights for light fixture 1 Chapter 4 Carton 36 of 44: Projector Screen, 74-5416-xx, CTS3K-SCREEN Kit ID Number Sub-Kit ID Number Part Number 74-5416-xx Part Descripti
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-M Table Shelf and Table Section Assemblies Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 700-23340-xx Display shelf support right 3 Chapter 2 700-23341-xx Codec safety tray 3 Chapter 2 Carton 40 of 44: Tabletop Leg Base, 69-1620-xx, CTS3K-STRUCTURE Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 69-1620-xx 700-23305-01 I
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-M Table Shelf and Table Section Assemblies Carton 44 of 44: Tabletop Sections, Display Shelves, and Speaker Boards, 69-1835-01, CTS3K-M Sub-Kit ID Kit ID Number Number Part Number Part Description Qty Chapter Parts List Reference 74-5299-01 95-9686-01 Tabletop section: Center 1 Chapter 6 74-5300-01 95-9687-01 Tabletop section: Center right 1 Chapter 6 74-5301-01 95-9689-01 Tabletop section: Center left 1 Chapter 6
Appendix A Appendix A: Parts List Sorted by Carton Carton List for CTS3K-M Table Shelf and Table Section Assemblies Cisco TelePresence System 3000 A-26 OL-14521-01
A P P E N D I X B Appendix B: Region- and Country-Specific Equipment Revised: October 31, 2008, OL-14521-01 The following countries and regions have equipment manufactured to local regulations: Asia Pacific Part Description Part Number Qty TelePresence Power Cord PWR-CORD10-AP 37-0831-01 6 I/O modules: power/Ethernet CTS-LAPCONN-AP 74-4861-01 6 Notes Argentina Part Description Part Number Qty TelePresence Power Cord PWR-CORD10-AR 37-0841-01 6 I/O modules: power/Ethernet CTS-LAPCONN-AR 7
Appendix B Appendix B: Region- and Country-Specific Equipment Australia Australia Part Description Part Number Qty TelePresence Power Cord PWR-CORD10-AU 37-0840-01 6 I/O modules: power/Ethernet CTS-LAPCONN-AU 74-4866-01 6 Part Description Part Number Qty TelePresence Power Cord PWR-CORD10-CE 37-0832-01 6 I/O modules: power/Ethernet CTS-LAPCONN-CE 74-4865-01 6 Part Description Part Number Qty TelePresence Power Cord PWR-CORD10-CN 37-0837-01 6 I/O modules: power/Ethernet CTS-LAPCON
Appendix B Appendix B: Region- and Country-Specific Equipment Israel Israel Part Description Part Number Qty TelePresence Power Cord PWR-CORD10-ISR 37-0842-01 6 I/O modules: power/Ethernet CTS-LAPCONN-ISR 74-4863-01 6 Notes Italy Part Description Part Number Qty TelePresence Power Cord PWR-CORD10-ITA 37-0832-01 6 I/O modules: power/Ethernet CTS-LAPCONN-ITA 74-4865-01 6 Notes Japan Part Description Part Number Qty TelePresence Power Cord PWR-CORD10-JP 37-0847-01 6 I/O modules: pow
Appendix B Appendix B: Region- and Country-Specific Equipment Switzerland Switzerland Part Description Part Number Qty TelePresence Power Cord PWR-CORD10-SWI 37-0843-01 6 I/O modules: power/Ethernet CTS-LAPCONN-SWI 6 74-4862-01 Notes United Kingdom Part Description Part Number Qty TelePresence Power Cord PWR-CORD10-UK 37-0831-01 6 I/O modules: power/Ethernet CTS-LAPCONN-UK 74-4861-01 6 Notes Cisco TelePresence System 3000 B-4 OL-14521-01
