Varoitus Laitteisto tulee asentaa paikallisten ja kansallisten sähkömääräysten mukaisesti. Attention L'équipement doit être installé conformément aux normes électriques nationales et locales. Warnung Die Installation der Geräte muss den Sicherheitsstandards entsprechen. Avvertenza L'installazione dell'impianto deve essere conforme ai codici elettrici locali e nazionali. Advarsel Installasjon av utstyret må samsvare med lokale og nasjonale elektrisitetsforskrifter.
38 78-18795-01
Explosive Gas Warning Warning The use of the Cisco Unified Wireless IP Phone in hazardous environments such as areas where high levels of explosive gas may be present is not recommended. Check with the site safety engineer before using any type of wireless device in such an environment. Battery Disposal Warning Do not dispose of the battery pack in fire or water. The battery may explode if placed in the fire.
Japanese Electric Appliance and Radio Laws Statement 371—Power Cable and AC Adapter Statement 372—Wireless LAN Products Battery Safety Notices These battery safety notices apply to the batteries that are approved by the Cisco Unified Wireless IP Phone manufacturers.
Caution This symbol means reader be careful. In this situation, you might do something that could result in equipment damage. Refer to the product documentation for instructions. Caution The battery pack is intended for use only with this device. Caution Do not disassemble, crush, puncture, or incinerate the battery pack. Caution To avoid risk of fire, burns, or damage to your battery pack, do not allow a metal object to touch the battery contacts.
Caution Handle a damaged or leaking battery with extreme care. If you come in contact with the electrolyte, wash the exposed area with soap and water. If the electrolyte has come in contact the eye, flush the eye with water for 15 minutes and seek medical attention. Caution Do not charge the battery pack if the ambient temperature exceeds 104 degrees Fahrenheit (40 degrees Celsius). Caution Do not expose the battery pack to high storage temperatures (above 140 degrees Fahrenheit, 60 degrees Celsius).
Caution To obtain a replacement battery, contact your local dealer. Use only the batteries that have a Cisco part number. Caution Use only the Cisco power supply that is compatible with your phone. To order your power supply, contact your local dealer and refer to the list of Cisco part numbers.
• The use of wireless devices in hazardous locations is limited to the constraints posed by the safety directors of such environments. • The use of wireless devices on airplanes is governed by the Federal Aviation Administration (FAA). European Directives This section includes conformity statements for European directives.
English This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. [Bulgarian]: [Czech]: Dansk [Danish]: Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i Direktiv 1999/5/EF. Deutsch [German]: Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 1999/5/EU.
[Greek]: Français [French]: Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la Directive 1999/5/EC. Íslenska [Icelandic]: Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar 1999/5/EC. Italiano [Italian]: Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/CE.
Malti [Maltese]: Magyar [Hungarian]: Norsk Norwegian Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-direktiv 1999/5/EF. Polski [Polish]: Português [Portuguese]: Este equipamento está em conformidade com os requisitos essenciais e outras provisões relevantes da Directiva 1999/5/EC. [Romania]: Slovenskos [Slovenian]: Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi pogoji Direktive 1999/5/EC.
Slovensky [Slovak]: Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými nariadeniami direktív: 1999/5/EC. Suomi [Finnish]: Svenska [Swedish]: Note 48 You can check on the approval status of your product at the following URL: http://tools.cisco.com/cse/prdapp/jsp/externalsearch.
Declaration of Conformity with Regard to the EU Directive 93/42/ECC This device cannot be categorized as a medical device in order to perform diagnostic, monitoring and treatment functions, as defined in the Medical Directive. However, it does conform to the EMC requirements of the Medical Directive 93/42/EEC.
CE Marking For the Cisco Unified Wireless IP Phone 7920 series, the following CE mark and class-2 identifier are affixed to the equipment and packaging: National Restrictions In the majority of the EU and other European Countries, the 2.4- and 5-GHz bands have been made available for the use of wireless LANs. Table 1 provides an overview of the regulatory requirements in general applicable for the 2.4- and 5-GHz bands. Note The regulatory limits for maximum output power are specified in eirp.
The requirements for any country may evolve. Cisco recommends that you check with the local authorities for the latest status of their national regulations for both the 2.4- and 5-GHz wireless LANs. Table 1 Overview of Regulatory Requirements for Wireless LANs Frequency Band (MHz) Max Power Level (eirp) (mW) Indoor Only Indoor and Outdoor 2400–2483.5 100 X 5150–53501 200 5470–5725 1.
France For 2.4 GHz, the output power is restricted to 10 mW eirp when the product is used outdoors in the band 2454–2483.5 MHz. There are no restrictions when used in other parts of the 2.4 GHz band. For more details, check http://www.arcep.fr/ Pour la bande 2,4 GHz, la puissance est limitée à 10 mW en p.i.r.e. pour les équipements utilisés en extérieur dans la bande 2454 – 2483,5 MHz. Il n’y a pas de restrictions pour des utilisations dans d’autres parties de la bande 2,4 GHz. Consultez http://www.arcep.
California Perchlorate Contamination Prevention Act (Title 22, California Code of Regulations, Chapter 33) The battery inside this product might contain perchlorate, a known hazardous substance, so special handling and disposal of this product might be necessary. For more information about perchlorate and best management practices for perchlorate-containing substances, see http://www.dtsc.ca.gov/HazardousWaste/Perchlorate/index.
Table 2 Standards Compliance (continued) Regulatory Compliance EMC1 54 Standard • EN 60950 • IEC 60950 • AS/NZS 60950 • 47 CFR Part 15 Class B# • CISPR 11 • CISPR 22 Class B# • AS/NZS CISPR 22 Class B# • CISPR 24 • ICES-003 Class B# • EN 301.489-1 • EN 301.
Table 2 Standards Compliance (continued) Regulatory Compliance EMC3 Standard • EN 61000-3-2 • EN 61000-3-3 • EN 61000-6-1 • KN222 • VCCI Class B# • 47 CFR Part 15 Class B# • CISPR 11 • CISPR 22 Class B# • AS/NZS CISPR 22 Class B# • CISPR 24 • FCC Part 15.247* • FCC Part 15.
Table 2 Standards Compliance (continued) Regulatory Compliance Japan EU RF Exposure3 Standard • IEEE 802.a** • IEEE 802.b/g* • TELEC 71** • EN 300.328* • EN 300.3862 • EN 301.893** • OET-65C (01-01) • ANSI C95.1 (91) • RSS-102 • AS/NZS 2772 • EN 50.360 1. Standards marked with a pound (#) are Class B for the Cisco Unified Wireless IP Phone 7920 and 7921G and do not apply to the chargers which are Class A products. 2.
3. Standards marked with a pound (#) are Class B for the Cisco Unified Wireless IP Phone 7920 and 7921G and do not apply to the chargers which are Class A products. * Standards marked with an asterisk (*) apply to the Cisco Unified Wireless IP Phone 7920 series when using 802.11b/g WiFi ** Standards marked with two asterisks (**) apply only to the Cisco Unified Wireless IP Phone 7921G when using 802.
RF Exposure Information The radio module has been evaluated under FCC Bulletin OET 65C (01-01) and found to be compliant to the requirements as set forth in 47 CFR Sections 2.1091, 2.1093, and 15.247 (b) (4) addressing RF Exposure from radio frequency devices. This model meets the applicable government requirements for exposure to radio frequency waves. This wireless phone contains a radio transceiver.
The highest measured SAR levels for the phones are these: • Cisco Unified Wireless IP Phone 7920 is 0.54 W/kg. • Cisco Unified Wireless IP Phone 7921G is 0.51W/kg. Additional information on SAR and RF Exposure can be obtained off the FCC website at: www.fcc.gov/oet/rfsafety There is no conclusive proof that these mobile phones are or are not a health risk. The FDA and numerous researchers are continuing studies of RF radiation and health issues.
There are several suggested methods to reduce exposure for the user. Among those include: 1. Using a hands-free handset to increase the distance between the antenna and the head of the user. 2. Orienting the antenna away from the user. Additional information can be obtained from the following documentation: • Cisco Systems Spread Spectrum Radios and RF Safety white paper at the following location: http://www.cisco.com/warp/public/cc/pd/witc/ao340ap/prodlit/rfhr_wi.
Additional information can also be obtained from the following organizations: • World Health Organization Internal Commission on Non-Ionizing Radiation Protection at www.who.int/emf • United Kingdom, National Radiological Protection Board at www.nrpb.org.uk • Cellular Telecommunications Association at www.wow-com.
RF Exposure Statement for the European Union This device has been evaluated and found compliant in accordance with EU EMF Directive 1999/519/EC. FCC Safety Compliance Statement The Federal Communications Commission (FCC), with its action in ET Docket 93-62, has adopted a safety standard for human exposure to Radio Frequency (RF) electromagnetic energy emitted by FCC-certified equipment.
Manufacturer’s FCC Declaration of Conformity Statement Model: Cisco Unified Wireless IP Phone 7920 FCC Certification Number: MCLU58H002 Model: Cisco Unified Wireless IP Phone 7921G FCC Certification Number: LDK7900001 Model: Cisco Unified Wireless IP Phone 7925G FCC Certification Number: LDK7925G0269 Manufacturer: Cisco Systems, Inc.
These devices comply with Part 15 rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules.
Caution The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency. Any changes or modification to said product not expressly approved by Cisco, including the use of non-Cisco antennas, could void the user’s authority to operate this device.
For more information, go to this URL: http://www.anatel.gov.br Compliance Statement for Canada This Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada.
This device complies with Class B Limits of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. The device is certified to the requirements of RSS-210 for 2.4-GHz spread spectrum devices.
Statement 191—VCCI Class A Warning for Japan Warning Note 68 This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions. See Table 2, Standards Compliance, for the EMC class for specific models and parts.
Statement 256—Class A Warning for Hungary Warning This equipment is a class A product and should be used and installed properly according to the Hungarian EMC Class A requirements (MSZEN55022). Class A equipment is designed for typical commercial establishments for which special conditions of installation and protection distance are used.
Statement 257—Class A Notice for Taiwan and Other Traditional Chinese Markets Warning This is a Class A Information Product, when used in residential environment, it may cause radio frequency interference, under such circumstances, the user may be requested to take appropriate countermeasures. Statement 257 Statement 294—Class A Warning for Korea Warning 70 This is a Class A Device and is registered for EMC requirements for industrial use. The seller or buyer should be aware of this.
Statement 340—Class A Warning for CISPR22 Warning This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Statement 340 Waarschuwing Dit is een product van klasse A. In een woonomgeving kan dit product radiostoring veroorzaken. In dat geval moet de gebruiker de juiste maatregelen nemen. Varoitus Tämä on A-luokan tuote.
Warnung Dies ist ein Produkt der Klasse A. Bei der Verwendung dieses Produkts im Haus- oder Wohnungsbereich kann es zu Funkstörungen kommen. In diesem Fall muss der Benutzer u. U. angemessene Maßnahmen ergreifen. Avvertenza Prodotto di classe A. È possibile che il prodotto generi interferenze radio in un ambienti chiusi. In questo caso l'utente deve intraprendere le misure adeguate per risolvere il problema. Advarsel Dette er et produkt i klasse A.
Regulatory Compliance and Safety Information 73
EMC Class B Notices and Warnings This section includes the EMC Class B warnings for the Cisco Unified Wireless IP Phone 7920 series. Statement 157—VCCI Compliance for Class B Equipment Warning 74 This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference.
Statement 295—Class B Notice for Korea Warning This is a Class B Device and is registered for EMC requirements for residential use. This device can be used not only in residential areas but in all other areas.
Using External Devices The following information applies when you use external devices with the Cisco Unified Wireless IP Phone. Cisco recommends the use of good quality external devices (such as headsets) that are shielded against unwanted radio frequency (RF) and audio frequency (AF) signals. Depending on the quality of these devices and their proximity to other devices such as mobile phones or two-way radios, some audio noise may still occur.
Caution In European Union countries, use only external headsets that are fully compliant with the EMC Directive [89/336/EC]. Related Documentation For more information, refer to the Cisco Unified Wireless IP Phone 7920 series publications available at this location: http://www.cisco.com/en/US/products/hw/phones/ps379/tsd_products_supp ort_series_home.
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0. Cisco Product Security Overview This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use.
