User Guide

FINAL DRAFT —Cisco Confidential
6-12
Cisco ASR 9000 Series Aggregation Services Router Getting Started Guide
OL-17502-01
Chapter 6 Troubleshooting the Cisco IOS XR Software
Interfaces Not Coming Up
Verifying System Interfaces
Perform the following steps to verify the system interfaces.
Step 1 Type the show platform command in administration EXEC to verify that all nodes are in the “IOS XR
RUN” state:
RP/0/RSP0/CPU0:router(admin)# show platform
Node Type PLIM State Config State
-----------------------------------------------------------------------------
0/1/SP MSC(SP) N/A IOS XR RUN PWR,NSHUT,MON
0/1/CPU0 MSC 16OC48-POS/DPT IOS XR RUN PWR,NSHUT,MON
0/2/SP MSC(SP) N/A IOS XR RUN PWR,NSHUT,MON
0/2/CPU0 MSC 16OC48-POS/DPT IOS XR RUN PWR,NSHUT,MON
0/3/SP MSC(SP) N/A IOS XR RUN PWR,NSHUT,MON
0/3/CPU0 MSC 16OC48-POS/DPT IOS XR RUN PWR,NSHUT,MON
0/RSP0/CPU0 RP(Active) N/A IOS XR RUN PWR,NSHUT,MON
0/RSP1/CPU0 RP(Standby) N/A IOS XR RUN PWR,NSHUT,MON
0/SM0/SP FC/S(SP) N/A IOS XR RUN PWR,NSHUT,MON
0/SM1/SP FC/S(SP) N/A IOS XR RUN PWR,NSHUT,MON
0/SM2/SP FC/S(SP) N/A IOS XR RUN PWR,NSHUT,MON
0/SM3/SP FC/S(SP) N/A IOS XR RUN PWR,NSHUT,MON
Step 2
Type the show ipv4 interface brief command to verify IP address configuration and protocol status:
RP/0/RSP0/CPU0:router# show ipv4 interface brief
Interface IP-Address Status Protocol
gi0/1/0/0 unassigned Shutdown Down
gi0/1/0/1 unassigned Shutdown Down
gi0/1/0/2 unassigned Shutdown Down
gi0/1/0/3 unassigned Shutdown Down
gi0/1/0/4 unassigned Shutdown Down
gi0/1/0/5 unassigned Shutdown Down
gi0/1/0/6 unassigned Shutdown Down
gi0/1/0/7 unassigned Shutdown Down
gi0/1/0/8 unassigned Shutdown Down
gi0/1/0/9 unassigned Shutdown Down
gi0/1/0/10 unassigned Shutdown Down
gi0/1/0/11 unassigned Shutdown Down
gi0/1/0/12 unassigned Shutdown Down
gi0/1/0/13 unassigned Shutdown Down
gi0/1/0/14 unassigned Shutdown Down
gi0/1/0/15 unassigned Shutdown Down
gi0/2/0/0 10.10.1.101 Down Down
gi0/2/0/1 unassigned Shutdown Down
gi0/2/0/2 unassigned Shutdown Down
gi0/2/0/3 unassigned Shutdown Down
TenGigE0/3/0/0 unassigned Shutdown Down
TenGigE0/3/0/2 unassigned Shutdown Down
MgmtEth0/RSP0/CPU0/0 unassigned Shutdown Down
Step 3 Configure the interfaces, as shown in the following examples.
Note Type the commit command to make the new configuration part of the active running
configuration. If you end the configuration session, you are automatically prompted to commit
the changes, as shown in the second example:
RP/0/RSP0/CPU0:router# configure