Cisco UC Phone 7925G Desktop Charger This chapter describes the Cisco UC Phone 7925G Desktop Charger for use with Cisco Unified Wireless IP Phone 7925G, 7925G-EX, 7925G and 7926G.
The Cisco UC Phone 7925G Desktop Charger provides the following features: • works on line power or from the spare battery for the phone • contains a Power LED and a Battery LED • contains a speakerphone, with the volume controlled by the phone volume buttons • supports Bluetooth headset through the speakerphone • charges the docked phone battery • contains an additional port at the back of the station for charging a spare battery batter Need a figure next: Cisco UC Phone 7925G Desktop Charger, shown with th
The spare battery onlyy charges when the Cisco UC U Phone 7925G Desktop Charger is plugged into line power. The Cisco UC Phone 7925G Desktop Charger supports Bluetooth version 2.1 + EDR using Handsfree version 1.5. The speakerphone supports Acoustic Echo Cancellation (AER) and Noise Noise Reduction (NR) to provide audio under a variety of noise environments. When the Cisco UC U Phone 7925G Desktop Charger establishes a Bluetooth connection, the AER and NR automatically disable.
Touch pad for charger function Detect etect switch for auto link lin function Prerequisites •The Cisco UC Phone 7925G Desktop Charger is connected to external power, or a charged spare battery installed. Procedure Step 1 Turn the phone on. Step 2 Choose tool > Phone Settings > Bluetooth > Device List. List Step 3 Press Scan.. The phone scans for a Bluetooth device. The device name for the charger is “Cisco Dock 7900”. Step 4 Select Cisco Dock 7900, 7900 and press Pair.
•the Cisco UC Phone 7925G Desktop Charger must be connected to an electrical outlet or have a charged spare battery installed. •the phone should be already paired with the charger. Procedure Step 1 Place the phone into the charger, using the following diagram. Diagram to be added after it is created. When the phone docks and pairing has been set up, the Power LED flashes blue. While the Power LED flashes blue, the phone and Cisco Unified Wireless IP Phone 7925G Desktop Charger are pairing.
Charge spare battery Use this procedure to install a spare battery so that it can be recharged. After becoming fully charged, the spare battery can be used as a power source (for a limited time) for the Cisco UC U Phone 7925G Desktop Charger. Prerequisites •The Cisco UC Phone 7925G Desktop Charger must be plugged into the electrical outlet. Procedure Step 1 Use the following diagram to insert the spare battery into the Cisco UC U Phone 7925G Desktop Charger.
•If an uncharged spare battery is in place, the station does not function. The Cisco UC Phone 7925G Desktop Charger must be plugged into an electrical output, or a charged spare battery installed. Troubleshooting Cisco UC U Phone 7925G Desktop Charger problems This section provides information to help you troubleshoot Cisco UC U Phone 7925G Desktop Charger problems. Power LED This section describes situations that are identified by the Power LED.
Battery LED lights green, the spare battery is fully charged. Battery LED unlit Problem The Battery LED is unlit. Cause No spare battery is installed in the Cisco UC U Phone 7925G Desktop Charger, or battery is not making contact correctly. Solution If a battery is not installed, this situation is normal. If a battery is installed, remove the battery and place it back into the charger. Also, check that the Power LED lights green. Battery LED is red Problem The Battery LED is red.
Statement 2002—Declaration Declaration of Conformity with Regard to the Directives 2006/95/EC and 2004/108/EC This equipment complies with the essential requirements and other provisions of Directives 2006/95/EC and 2004/108/EC. For more information, please refer to the Declaration of Conformity.
Modifying the equipment without Cisco's authorization may result in the equipment no longer complying with FCC requirements for Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Caution The Part 15 radio device operates on a non-interference interference basis with other devices operating at this frequency. Any changes or modification to said product not expressly approved by Cisco, including the use of non-Cisco Cisco antennas, could void the user's authority to operate this device. devic Statement 2022—Class Class B Notice for Canada This Class B digital apparatus complies with Canadian ICES-003.
équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Japanese Electric Appliance and Radio Laws Statement 371—Power Power Cable and AC Adapter Statement 295—Class Class B Warning for Korea Warning This is a Class B Device and is registered for EMC requirements for residential use. This device can be used not only in residential areas but in all other areas.
Statement 157—VCCI VCCI Compliance for Class B Equipment This is a Class B product based on the standard of the VCCI Council. If this is used near a radio or Warning television receiver in a domestic environment, it may cause radio Interference. Install and use the equipment according to the instruction manual.
