Cisco IR829 Integrated Services Router Hardware Installation Guide August 2015 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
CONTENTS Cisco IR829 Integrated Services Router Hardware Installation Guide 1 CHAPTER 1 Product Overview 1-1 General Description LEDs 1-4 Memory 1-6 SKU Information 1-1 1-6 Hardware Features 1-6 Platform Features for Cisco IR829 Reset Button 1-8 1-7 Antennas 1-8 Antennas and Installation Scenarios 1-8 Supported Cisco Antennas and Cables 1-10 CHAPTER 2 Power Supply 1-22 SFP Modules 1-22 Installing the Router 2-1 Equipment, Tools, and Connections 2-2 Items Shipped with your Router 2-2 Addit
Contents Connecting to DC Power 3-3 Plugs and Pin-Outs 3-4 Constructing a Power cable Wiring the DC Power 3-5 Verifying Connections CHAPTER 4 Initial Configuration 3-4 3-6 4-1 Setup Command Facility 4-1 Verifying the Initial Configuration Where To Go From Here 4-4 800 Series Documentation 4-4 4-4 Cisco IR829 Differences 4-5 LEDs 4-5 Software Bundle Installation CHAPTER 5 4-6 Guest Operating System (Guest OS) Installation and Configuration Guest Operating System Overview Prerequisites 5-1
Contents CHAPTER 6 Technical Specifications Router Specifications 6-1 6-1 6-2 Cisco IR829 Integrated Services Router Hardware Installation Guide 3
Contents Cisco IR829 Integrated Services Router Hardware Installation Guide 4
Preface This preface describes the objectives, audience, organization, and conventions of this guide and describes related documents that have additional information.
Preface Organization This guide is organized into the following chapters. Chapter Name Description Chapter 1 Chapter 1, “Product Overview” Describes the router models and the hardware features available. Chapter 2 Chapter 2, “Installing the Router” Lists the items shipped with the router, the equipment and tools necessary for installing the router, the safety warnings and guidelines, and the procedures for installing the router.
Preface Safety Warnings Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.
Preface Warnung WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
Preface Varning! VIKTIGA SÄKERHETSANVISNINGAR Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.
Preface Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.
Preface Cisco 829 Integrated Services Router Hardware Installation Guide 7
Preface Warning When installing the product, please use the provided or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for any other electrical devices than products designated by CISCO.
Preface Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024 Warning If the symbol of suitability with an overlaid cross appears above a port, you must not connect the port to a public network that follows the European Union standards.
Preface Warning Hot surface. Statement 1079 Related Documentation • Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers • Cisco IOS Release Notes • Cisco 800 Series Integrated Services Routers Software Configuration Guide. Searching Cisco Documents To search an HTML document using a web browser, press Ctrl-F (Windows) or Cmd-F (Apple).
CH A P T E R 1 Product Overview This chapter provides an overview of the features available for the Cisco IR829 Integrated Services Routers (ISRs) and contains the following sections: Note • General Description, page 1-1 • SKU Information, page 1-6 • Hardware Features, page 1-6 For compliance and safety information, see Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers.
Chapter 1 Product Overview General Description Figure 1-2 shows the front panel details of the Cisco IR829. Figure 1-2 Cisco IR829 Front Panel 1 CELLULAR 0 AUX 5 Serial Ports 2 Limited Modularity Slot 6 USB-A Port 3 Gigabit WAN 7 Power Input, Battery, and Ignition connector. Refer to the DC Power section for pin-outs. 4 Gigabit LAN/PoE 8 WLAN ANT0 5GHz Figure 1-3 shows the back panels details of the Cisco IR829. Figure 1-3 Note Cisco IR829 Back Panel 1 WLAN ANT 0 2.
Chapter 1 Product Overview General Description Figure 1-4 Behind the SIM Door Figure 1-5 shows the top of the Cisco IR829. Figure 1-5 Cisco IR829 Top Cover Figure 1-6 shows the LED detail.
Chapter 1 Product Overview General Description Figure 1-6 Cisco IR829 LED Detail The following section shows a detailed description of the LEDs. LEDs The following table describes the LEDs for the Cisco IR829.
Chapter 1 Product Overview General Description Table 1-1 LED Descriptions (continued) LED Activity Description GPS GPS Status Off — GPS not configured On — GPS configured Slow Flash — GPS Acquiring in Standalone GPS Fast Flash — GPS Acquiring in Assisted GPS Note Slow Flash is defined as the LED will be on for 0.25 seconds and off for 0.75 seconds. Fast Flash s defined as the LED will be on for 0.25 seconds and off for 0.25 seconds.
Chapter 1 Product Overview SKU Information RSSI RSSI (2) RSSI (1) RSSI (0) -90 — 75dBm Off Off On - Green -75 — 60dBm Off On - Green On - Green >60dBm On - Green On - Green On - Green Memory The Cisco IR829 uses flash memory and main memory. The flash memory contains the Cisco IOS software image and the boot flash contains the ROMMON boot code. All memory components are factory default and not upgradeable by the end user. Table 1-2 shows the memory allocation.
Chapter 1 Product Overview Hardware Features • Reset Button, page 1-8 • Supported Cisco Antennas and Cables, page 1-10 • Power Supply, page 1-22 Platform Features for Cisco IR829 The following lists the hardware platform features for the Cisco IR829. • Intel Atom Dual-Core Rangeley CPU, 1250 MHz • 2GB DDR3 memory capacity • 64MB SPI BIOS NOR flash • 8GB (4GB usable) “eMMC” bulk storage flash • 4-port GE LAN switch, optional PoE 802.
Chapter 1 Product Overview Antennas Reset Button The Reset button resets the router configuration to the default configuration set by the factory. To restore the router configuration to the default configuration set by the factory, use a standard size #1 paper clip with wire gauge 0.033 inch or smaller and simultaneously press the reset button while applying power to the router. Note The rear cover must be removed to expose the reset switch. Antennas The IR829 has 4 x Wi-Fi antennas (2.
Chapter 1 Product Overview Antennas Figure 1-8 Sample Installation Installation Users need to provision a 8 x 8" flat mounting surface with a mounting hole on the roof of the vehicle for the 5-in-1 antenna, and a 6 x 6" flat mounting surface with a mounting hole for the 2-in-1 WiFi antenna. Without a flat mounting surface, the antenna will not meet IP67 standards and may have reduced service life. Ground plane Cisco recommends having a 1 foot ground plane under both the 5-in-1 and 2-in-1 antennas.
Chapter 1 Product Overview Antennas MIMO ports on 5-in-1 and 2-in-1 Cellular and WLAN ports on the 5-in-1 and 2-in-1 antennas support MIMO technology. MIMO brings significant improvements in throughput and robustness of the wireless link in fading channels. Users choosing to connect only one wireless port on MIMO capable products are giving up significant wireless performance in both throughput and robustness of the link.
Chapter 1 Product Overview Antennas Table 1-4 Use Case 4G/LTE Radio Modules/Cables/Antennas Radio Module Lightning Arrestor or Adapter Indoor Cable Outdoor Cable Antenna R/A-TNC(m) to N(m), LMR-240-FR/CMR, 1', qty 2 • Note 37-100705-01 Not available from Cisco R/A-TNC(m) to N(m), LMR-240-FR/CMR, 5', qty 2 • Note 37-100717-01 Not available from Cisco R/A-TNC(m) to N(m), LMR-240-FR/CMR, 10', qty 2 • Note 37-100754-01 Not available from Cisco R/A-TNC(m) to N(m), LMR-240-FR/CMR, 15', qty 2 • Not
Chapter 1 Product Overview Antennas Table 1-4 4G/LTE Radio Modules/Cables/Antennas Use Case Radio Module 4G/LTE Case 3: IR829GW-LTE None -GA-EK9 —OR IR829GW-LTE qty 2x -GA-ZK9 PID: 4G-AE010-R IR829GW-LTE CPN: 07-1144-01 -NA-AK9 Front Panel Swivel Mount 4G-LTE dipoles Indoor Cable Lightning Arrestor or Adapter Outdoor Cable Antenna None None Qty 2 x 4G Indoor Swivel Mount Dipole, 0 dBi, TNC(m), white • 07-1174-01 • ANT-4G-DP-IN-TN C IR829GW-LTE 10ft extension base for TNC dipole -VZ-AK9 a
Chapter 1 Product Overview Antennas Table 1-4 4G/LTE Radio Modules/Cables/Antennas Use Case Radio Module 4G/LTE Case 5: IR829GW-LTE None -GA-EK9 2x ceiling mount 4G-LTE antennas IR829GW-LTE -GA-ZK9 IR829GW-LTE -NA-AK9 IR829GW-LTE -VZ-AK9 2x TNC(f) Indoor Cable Lightning Arrestor or Adapter Outdoor Cable Antenna None None Qty 2 x 4G Indoor omni-directional Ceiling Mount 2 dBi, • 07-1121-01 • 4G-ANTM-OM-C M — OR Qty 2 x 4G Dipole Ceiling Mount 2 dBi • 07-1174-01 • ANT-4G-DP-IP-TN C GPS
Chapter 1 Product Overview Antennas Table 1-5 lists the supported Single Band Cisco WiFi antenna for the Cisco IR829. Table 1-5 Supported Single Band Cisco WiFi Antenna Use Case Radio Module Indoor Cable WiFi Use Case 2: Dual Band N/A Simultaneous Single Band, Front 802.11n 2x2 MIMO Panel Mounted WiFi Antennas Lightning Arrestor or Adapter Outdoor Cable N/A N/A Antenna 2x Single Band, Swivel Mount Omni, RP-TNC(plug), 2.2dBi @ 2.
Chapter 1 Product Overview Antennas Table 1-5 Supported Single Band Cisco WiFi Antenna(continued) Use Case Radio Module WiFi Use Case 5: Indoor Cable Dual Band None Simultaneous Single Band, Dual 802.
Chapter 1 Product Overview Antennas Table 1-5 Supported Single Band Cisco WiFi Antenna(continued) Use Case Radio Module Indoor Cable WiFi Use Case 7: Dual Band Simultaneous Single Band, Dual 802.
Chapter 1 Product Overview Antennas Table 1-6 Supported Dual Band Cisco WiFi Antenna(continued) Use Case Radio Module WiFi Use Case 9: Dual Band N/A Simultaneous 802.11n 2x2 MIMO WiFi Dual Band, Dual Element, Wall Mounted Antennas Indoor Cable Lightning Arrestor or Adapter Outdoor Cable N/A N/A Connectors: 2x RP-TNC (jack) WiFi Use Case 10: Dual Band N/A Simultaneous 802.
Chapter 1 Antennas Cisco IR829 Integrated Services Router Hardware Installation Guide 1-18 Product Overview
Chapter 1 Product Overview Antennas Use Case Extension Cable Antenna Transportation Use Case 1: No extension cables are required if the IR829 is located within ~1.0ft of 5-in-1 antenna, and ~2.0ft of WiFi 2-in-1 antenna. Quinta 5 element 5-in-1 transportation antenna, black radome color, 2x 4G cellular, 2x dual band WiFi, 1xGPS 7 x RF ports, with the IR829 deployed in a transportation application. (Default Configuration) Quinta 5-in-1 antenna AND a WiFi 2-in-1 antenna to utilize all 7 ports.
Chapter 1 Antennas Use Case Extension Cable Transportation Use Case 1 Continued: WiFi 2.
Chapter 1 Product Overview Antennas Use Case Extension Cable Antenna Transportation Use Case 2: No extension cables are required if the Tercia 3 element 3-in-1 transportation IR829 unit is located within ~1.0ft of antenna, black radome color, 2x 4G 7 x RF ports, with the IR829 deployed 3-in-1 antenna, and ~2.0ft of WiFi 2-in-1 cellular, 1xGPS in a transportation application. antenna.
Chapter 1 Product Overview Power Supply Power Supply The Cisco IR829 comes with an external power connector. • Direct-wire 12/24VDC vehicle charging system input (9 — 32VDC). • 4-pin locking power connector. SFP Modules The router Ethernet SFP modules provide connections to other devices. These field-replaceable transceiver modules provide the uplink interfaces. Local connectors (LCs) provide the fiber-optic connection. RJ-45 connectors allow copper connections.
CH A P T E R 2 Installing the Router This chapter describes the equipment and the procedures for successfully installing the Cisco IR829 and contains the following sections: • Equipment, Tools, and Connections, page 2-2 • Installing the Router, page 2-3 Caution Do not place anything on top of the router that weighs more than 10 pounds (4.5 kilograms), and do not stack routers on a desktop. Excessive weight on top of the router could damage the chassis.
Chapter 2 Installing the Router Equipment, Tools, and Connections Warning This product is not intended to be directly connected to the Cable Distribution System. Additional regulatory compliance and legal requirements may apply for direct connection to the Cable Distribution System. This product may connect to the Cable Distribution System ONLY through a device that is approved for direct connection.
Chapter 2 Installing the Router Installing the Router Ethernet Devices Identify the Ethernet devices that you will connect to the router: hub, servers, and workstations or PCs. Ensure that each device has a network interface card (NIC) for connecting to Ethernet ports. If you plan to configure the software using Cisco IOS commands through the console port, provide an ASCII terminal or a PC that is running terminal emulation software to connect to the console port.
Chapter 2 Installing the Router Installing the Router Warning Note Hot surface. Statement 1079 High Temperature SIMs are required for 4G operations if the Ambient temperature is above 95F (35C) To access the SIM card in the Cisco IR829, follow these steps: Step 1 Place the router on its bottom and ensure that any installed antennas are carefully oriented. Step 2 Remove the SIM access panel using two Phillips head screws. (See Figure 2-1.) Step 3 Locate the SIM card you wish to install/replace.
Chapter 2 Installing the Router Installing the Router Installing Antennas Note Before you install the Cisco IR829 Integrated Services Router on a table, wall, or DIN rail, install the antennas on the front panel. It is difficult to install the antennas after the router is installed. There are four TNC connectors on the front side of the chassis. There are two TNC and one SMA connectors on the back side of the chassis. Two TNC connectors are used to connect to the 4G modem.
Chapter 2 Installing the Router Installing the Router Figure 2-3 Step 2 Install the router to a wall stud using two number-10 wood screws, round- or pan-head, with number-10 washers or two number-10 washer-head screws. The screws must be long enough to penetrate at least 1.0 inch (25.4 mm) into the supporting wood or metal wall stud. (See Figure 2-4.) Figure 2-4 Note Step 3 Cisco IR829 Mounting Holes Mounted to wall For hollow-wall mounting, each bracket requires two wall anchors with washers.
Chapter 2 Installing the Router Installing the Router Installing the Router Ground Connection The router must be connected to a reliable earth ground. Install the ground wire in accordance with local electrical safety standards. • For NEC-compliant grounding, use size 14 AWG (2 mm2) or larger copper wire and a ring terminal with an inner diameter of 1/4 in. (5 to 7 mm). • For EN/IEC 60950-compliant grounding, use size 18 AWG (1 mm2) or larger copper wire. Warning This equipment must be grounded.
Chapter 2 Installing the Router Cisco IR829 Integrated Services Router Hardware Installation Guide 2-8 Installing the Router
CH A P T E R 3 Connecting the Router This chapter describes how to connect Cisco IR829 Integrated Services Router (ISRs) to Ethernet devices and a network.
Chapter 3 Connecting the Router Preparing to Connect the Router Connecting a PC, Server, or Workstation To connect a PC (or other Ethernet devices) to an Ethernet switch port, follow these steps: Step 1 Connect one end of the Ethernet cable to an Ethernet switch port on the router. In this example a PC is being connected to GE LAN Port 2. See Figure 3-1.
Chapter 3 Connecting the Router Connecting a Terminal or PC to the Console Port Step 3 (Optional) Connect additional servers, PCs, or workstations to the other Ethernet switch ports. Connecting a Terminal or PC to the Console Port Connect a terminal or PC to the Console port either to configure the software by using the CLI or to troubleshoot problems with the router.
Chapter 3 Connecting the Router Connecting to DC Power Plugs and Pin-Outs The IR829 ships with a DC power accessory kit that contains a 4-pin locking connector and pins to use for the power connections. Four contacts are supplied, but only three are used. One is a spare. The power entry receptacle is on the IR829. The pin-outs are shown in Figure 3.
Chapter 3 Connecting the Router Connecting to DC Power Figure 3-5 Power cable 3 2 1 349790 4 Details listed in the power cable example are: 1 4-pin locking connector 2 2 loops of DC power and power return wires only. Other wires that may be used should run outside the Ferrite. 3 Note Ferrite bead and the loops of wire are not needed at this time. Note Ferrite bead and the loops of wire are not needed at this time.
Chapter 3 Connecting the Router Verifying Connections Step 3 Using the pins included in the kit, crimp each pin onto a wire. Step 4 Insert the pins into the power connector, referring to previous figures for guidance. Step 5 Plug the connector into the power entry receptacle. Verifying Connections To verify that all devices are properly connected to the router, first turn on all the connected devices, then check the LEDs. To verify router operation, refer to Table 3-1.
Chapter 3 Connecting the Router Verifying Connections Table 3-1 Verifying the Router Operation (continued) Power and Link LEDs to Check Normal Patterns Sim cards SIM0/SIM1 Off — No USIM Green — USIM installed and active Cellular Modems CELLULAR0/ CELLULAR1 Off — Module not powered on On — Module is powered on and connected but not transmitting or receiving Slow Blink — Module is powered on and searching for connection Fast Blink — Module is transmitting or receiving.
CH A P T E R 4 Initial Configuration This chapter provides instructions for initial configuration of the Cisco IR829 Integrated Services Routers (ISRs). To create the initial configuration, the setup command facility prompts you for basic information about your router and network.
Chapter 4 Initial Configuration Setup Command Facility Note If you make a mistake while using the setup command facility, you can exit and run the setup command facility again. Press Ctrl-C and enter the setup command at the privileged EXEC mode prompt (Router#). To proceed using the setup command facility, enter yes. Would you like to enter the initial configuration dialog? yes Step 3 When the following messages appear, enter yes to enter basic management setup.
Chapter 4 Initial Configuration Setup Command Facility Async0 Async1 GigabitEthernet2 Cellular0 Cellular1 Step 9 unassigned unassigned unassigned unassigned unassigned YES YES NO NO NO unset unset unset unset unset up up up down down down down up down down Choose one of the available interfaces for connecting the router to the management network.
Chapter 4 Initial Configuration Verifying the Initial Configuration After the initial configuration file is created, you can use the Cisco IOS CLI to perform additional configuration. Verifying the Initial Configuration To verify that the new interfaces are operating correctly, perform the following tests: • To verify that the interfaces and line protocol are in the correct state—up or down—enter the show interfaces command.
Chapter 4 Initial Configuration Cisco IR829 Differences Cisco IR829 Differences This section will discuss some of the ways that the Cisco IR829 differs from the rest of the 800 series. LEDs The Cisco IR829 has LEDs that are discussed in previous chapters in this guide. There is also a command that will show you the status of the LEDs if you are not near the device. Use the show platform led command with options to view the different output.
Chapter 4 Initial Configuration Cisco IR829 Differences IR800#show platform led system System LED: amber, blinking Summary of the LED status providers: Client Type ------------------------------ -------GigabitEthernet5 critical Note Status -------OK There may be a lag time between the LED indication on the router and what the show led commands return. Software Bundle Installation The Cisco IR829 ships with the latest software available with the configuration that was ordered.
Chapter 4 Initial Configuration Cisco IR829 Differences updating IOS image... Sending file modes: C0644 61505652 ir800-universalk9-mz.SSA.156-0.3.T IOS md5 verification passed! Done! IR800# *Jun 25 18:51:16.975: %SYS-5-CONFIG_I: Configured from console by bundle install command *Jun 25 18:51:16.975: %IR800_INSTALL-6-SUCCESS_BUNDLE_INSTALL: Successfully installed bundle image. Step 3 Save the configuration and reload the router.
Chapter 4 Cisco IR829 Differences Cisco IR829 Integrated Services Router 4-8 Initial Configuration
CH A P T E R 5 Guest Operating System (Guest OS) Installation and Configuration This chapter details Guest Operating System (Guest OS) installation for the Cisco IR829.
Chapter 5 Guest Operating System (Guest OS) Installation and Configuration Prerequisites Figure 5-1 Connectivity Between Cisco IOS and Guest OS In this example, number 1 is the interface being used on the router and number 2 is the interface on the Linux OS. For the Cisco IR829, 1 is Gigabit Ethernet 5 and 2 is Eth 0. Prerequisites • Router must be running Cisco IOS. Guidelines and Limitations • The bundled Guest OS is based on Linux kernel version 3.8.11.
Chapter 5 Guest Operating System (Guest OS) Installation and Configuration Configuring Cisco IOS Command Purpose bundle install flash: .CG Installs the specified bundle. copy running config-config startup-config Saves the current running configuration. reload Reloads the router. Configuring Cisco IOS This section describes how to configure the Cisco IOS VM to provide network connectivity to the Guest OS VM.
Chapter 5 Guest Operating System (Guest OS) Installation and Configuration Configuring Cisco IOS ipv6 dhcp client pd prefix-from-provider end The following example configures G5 to allow the Guest OS network connectivity: interface GigabitEthernet 5 duplex auto speed auto ipv6 address prefix-from-provider ::2:0:0:0:1/64 ipv6 enable end Enabling IPv4 Gigabit Ethernet To enable an external Gigabit Ethernet IPv4 interface on the IR829 to provide network connectivity, enter the following commands: Command
Chapter 5 Guest Operating System (Guest OS) Installation and Configuration Configuring Cisco IOS Configuring Guest OS Interface on Cisco IOS The Guest OS Ethernet port (eth0) connects to GigabitEthernet 5 on Cisco IOS. To configure the GigabitEthernet 5 interface with the default gateway address of the DHCP pool, enter the following commands: Note IPv6 must always be enabled on GigabitEthernet 5.
Chapter 5 Guest Operating System (Guest OS) Installation and Configuration Configuring Guest OS Enabling Guest OS Console For heightened security, Guest OS console is disabled by default. To enable Guest OS console, enter the following commands: Command Purpose config terminal Enters global configuration mode. line 1/4 Specifies line 1/4 for configuration and enters line configuration collection mode. transport input all Defines which protocols to use to connect to a specific line of the router.
Chapter 5 Guest Operating System (Guest OS) Installation and Configuration Configuring Guest OS Command Purpose telnet 9.1.2.1 2070 Accesses the Guest OS console. This uses the IP address of the Gigabit Ethernet 5 port. The following is the example result: EXAMPLE Poky 9.0 (Yocto Project 1.4 Reference Distro) 1.4 qemux86 ttyS0 qemux86 login: root root@qemux86:~# Setting the Root Password Guest OS does not have a default root password.
Chapter 5 Guest Operating System (Guest OS) Installation and Configuration Configuring NAT Note Ensure that the PermitEmptyPasswords parameter is set to no. PermitRootLogin yes PasswordAuthentication yes PermitEmptyPasswords no Step 3 Restart SSHD: [GOS]# /etc/init.d/sshd stop Stopping sshd: [GOS]# /etc/init.d/sshd start Starting sshd: [GOS]# Step 4 [ OK ] [ OK ] From the IOS command line, enter the following: IR800#iox host exec enablessh IR800-GOS-1 ssh enabled successfully.
Chapter 5 Guest Operating System (Guest OS) Installation and Configuration Troubleshooting Pro tcp tcp --- Inside global 9.1.1.131:22 9.1.1.131:60100 9.1.1.131 Inside local 192.168.1.2:22 192.168.1.2:60100 192.168.1.2 Outside local 9.1.1.3:53649 9.1.1.3:22 --- Outside global 9.1.1.3:53649 9.1.1.3:22 --- Troubleshooting To determine common causes of configuration failure, enter the following commands: Command Purpose ifconfig eth0 Checks if Guest OS is assigned an IP address.
Chapter 5 Guest Operating System (Guest OS) Installation and Configuration Related Documentation For information on supporting systems referenced in this guide, see the following documentation on Cisco.com: Cisco ASR 1000 Series Aggregation Services Routers Configuration Guide Cisco 3945 Series Integrated Services Router Cisco 2000 Series Connected Grid Routers Installation and Configuration Guide for Cisco Services Ready Engine Virtualization 1.
CH A P T E R 6 Technical Specifications This appendix provides router, port, cabling specifications, and power adapters for the Cisco IR829 Integrated Services Router (ISRs). Note For compliance and safety information, see the Regulatory Compliance and Safety Information Roadmap that was shipped with the router and Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers. Router Specifications Table 6-1 lists the operational limits of the Cisco IR829.
Chapter 6 Table 6-1 Technical Specifications Cisco IR829 Specifications (continued) Description Design Specification Military Standard MIL-STD-810G Method 514.6: Procedure 1 Category 4, Secured Cargo - Common MIL-STD-810G Method 514.6: Procedure 1 Category 20, Ground Vehicles MIL-STD-810G Method 516.6. Procedure 1, Functional Shock MIL-STD-810G Method 516.6. Procedure 5, Crash Hazard MIL-STD-810G Method 516.6.
IMPORTANT! READ ALL THE SAFETY INFORMATION BEFORE INSTALLING THE HARDWARE Getting Started and Product Document of Compliance for the Cisco IR829 Integrated Services Router • Cisco Information, page 2 • Introduction, page 2 • Items Shipped with your Router, page 2 • Equipment that you supply, page 2 • Related Documentation, page 3 • Installation Warning and Caution Statements, page 4 • Grounding the Router, page 5 • Connecting DC Power, page 6 • Connecting to the Router Gateway Ports, page 8
Cisco Information Table 1 Cisco Company Name and Address Details Company Name Cisco Address Cisco Systems, Inc. 170 West Tasman Drive, San Jose, CA 95134-1706, United States. Introduction The purpose of this document is to provide the installer the necessary information for installing the Cisco IR829 Integrated Services Router. The documentation is on-line, and subject to change. Make sure that you are downloading or viewing on-line the latest version before beginning an installation.
Related Documentation To access resources or to display the latest Cisco 800 Series Router documentation on-line, go to this URL:www.cisco.com/go/800 This portal has all of the information you need to get to know your router, install and configure it, as well as access software. Look at the right side of the page under Support.
Installation Warning and Caution Statements Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.
Warning Avoid using or servicing any equipment that has outdoor connections during an electrical storm. There may be a risk of electric shock from lightning. Statement 1088 Caution The equipment shall only be used in an area of not more than pollution degree 2, as defined in IEC 60664-1. The equipment shall be installed in a certified ATEX enclosure that provides a degree of protection not less than IP 54 in accordance with IEC 60079-15. Caution Airflow around the Router must be unrestricted.
Caution Use at least a 4 mm2 conductor to connect to the external grounding screw. The ground lug is supplied with the device. To ground the router to earth ground by using the ground screw, follow these steps: Locate the ground lug in the packaging kit. Store the ground screw for later use. Step 2 Use a wire stripping tool to strip the 14-16 AWG (2.08-1.31mm²) grounding wire to 0.22 in. (5.56 mm).
Warning Explosion Hazard—Substitution of components may impair suitability for Class I, Division 2/Zone 2. Statement 1083 Warning Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV) requirements in IEC 60950 based safety standards. Statement 1033 Plugs and Pin-Outs The following is a brief overview of connecting to DC power. Details can be found in the Cisco IR829 Integrated Services Router Hardware Installation Guide and should be understood before beginning.
Step 3 Using the pins included in the kit, crimp each pin onto a wire. Step 4 Insert the pins into the power connector, referring to previous figures 1 and 2 for guidance. Step 5 Plug the connector into the power entry receptacle. Connecting to the Router Gateway Ports For hazardous location environments, follow these warnings when connecting to the destination ports (antenna, serial, Ethernet, and console ports).
Hazardous Locations Standards and Marking Strings The following standards were used for the hazardous locations approvals and certifications: ANSI/ASA 12.12.01-2013 CAN/CSA C22.2 No. 60079-0-11 Ed. 2 CAN/CSA C22.2 No. 60079-15-12 Ed. 1 CSA C22.2 No.
This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotopically radiated power (EIRP) is not more than that permitted for successful communication. Operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. Users are advised that high-power radars are allocated as primary users (i.e.
• International Commission on Non Ionizing Radiation Protection (ICNIRP) 98 • Ministry of Health (Canada) Safety Code 6. Limits on Human Exposure to Radio Frequency Fields in the range from 3kHz to 300 GHz • Australia Radiation Protection Standard To ensure compliance with various national and international Electromagnetic Field (EMF) standards, the system should only be operated with Cisco approved antennas and accessories.
This Device Meets the Industry Canada Guidelines for Exposure to Radio Waves The IR829 series device includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) as referenced in Health Canada Safety Code 6. The guidelines include a substantial safety margin designed into the limit to ensure the safety of all persons, regardless of age and health.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) © 2015 Cisco Systems, Inc. All rights reserved.
