User's Manual

ManualsBrandsCisco Systems ManualsElectronicsCisco LoRaWAN Interface Module

Table Of Contents

Important! Read All the Safety Information Before Installing the Hardware.
Getting Started and Product Document of Compliance for the Cisco LoRaWAN Interface Module

Cisco Systems, Inc. www.cisco.com

Getting Started and

Product Document of Compliance for the

Cisco LoRaWAN Interface Module

First Published: 2016-09-20

Last Updated: 2016-10-10

78-100921-01C0

 Cisco Information, page 2

 Introduction, page 2

 Unpacking the Device, page 2

 Equipment That You Supply, page 3

 Related Documentation, page 3

 Installation Warning and Caution Statements, page 4

 Becoming Familiar With the Device, page 5

 Power, page 8

 Pole/Wall Mounting, page 9

 Grounding the Device, page 15

 Regulatory Compliance and Safety Information, page 15

For the complete installation procedure, please refer to the Cisco LoRaWAN Interface Module Hardware Installation

Guide on Cisco.com:

http://www.cisco.com/c/en/us/support/routers/interface-module-lorawan/products-installation-guides-list.html

Important!

Read All the Safety Information Before Installing the Hardware.

Summary of content (18 pages)

PAGE 1
Important! Read All the Safety Information Before Installing the Hardware.
PAGE 2
Getting Started and Product Document of Compliance for the Cisco LoRaWAN Interface Module Cisco Information Cisco Information Table 1 Cisco Company Name and Address Details Company Name Cisco Address Cisco Systems, Inc. 170 West Tasman Drive, San Jose, CA 95134-1706, United States. Introduction The purpose of this document is to provide the installer the necessary information for installing the Cisco LoRaWAN Interface Module. The documentation is on-line, and subject to change.
PAGE 3
Getting Started and Product Document of Compliance for the Cisco LoRaWAN Interface Module Equipment That You Supply — Outdoor GPS antenna lightning arrestor (ACC-LA-G-TM-TF=) Equipment That You Supply  ESD-preventive cord and wrist strap.  Crimping tool (such as Thomas & Bett part number WT2000, ERG-2001, or equivalent).  6 AWG (13.3 mm2) copper ground wire  Wire-stripping tools for stripping 6 AWG (13.
PAGE 4
Getting Started and Product Document of Compliance for the Cisco LoRaWAN Interface Module Installation Warning and Caution Statements Installation Warning and Caution Statements Warning: IMPORTANT SAFETY INSTRUCTIONS Means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.
PAGE 5
Getting Started and Product Document of Compliance for the Cisco LoRaWAN Interface Module Becoming Familiar With the Device Warning: Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant rules. The violation of the rule could lead to serious federal penalty. Note: The device is suitable for use in environmental air space in accordance with section 300.22.
PAGE 6
Getting Started and Product Document of Compliance for the Cisco LoRaWAN Interface Module Becoming Familiar With the Device Figure 1 Cisco LoRaWAN Interface Module Bottom and Right Panels 1 Pressure vent 4 LED indicators 2 DC power port 5 USB port 3 PoE-in port 6 Console port and Reset button 6
PAGE 7
Getting Started and Product Document of Compliance for the Cisco LoRaWAN Interface Module Becoming Familiar With the Device Figure 2 Cisco LoRaWAN Interface Module Top and Left Panels 1 LoRa antenna ports 3 GPS antenna port 2 Ground lug location Antennas The Cisco LoRaWAN Interface Module is equipped with two N-type radio frequency (RF) connectors (antenna ports 1 and 2) on the top of the unit for LoRa antennas, and one TNC connector on the left of the unit for the GPS antenna, as shown in Figure 3
PAGE 8
Getting Started and Product Document of Compliance for the Cisco LoRaWAN Interface Module Becoming Familiar With the Device Déclaration d'exposition aux radiations Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 23 cm de distance entre la source de rayonnement et votre corps.
PAGE 9
Getting Started and Product Document of Compliance for the Cisco LoRaWAN Interface Module Pole/Wall Mounting  DC power—48 VDC Caution: Do not place the power injector in an unprotected outdoor environment because water could get into the power injector and cause a short circuit and possible fire.
PAGE 10
Getting Started and Product Document of Compliance for the Cisco LoRaWAN Interface Module Pole/Wall Mounting Warning: Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Warning: Installation of the equipment must comply with local and national electric codes.
PAGE 11
Getting Started and Product Document of Compliance for the Cisco LoRaWAN Interface Module Pole/Wall Mounting Wall Mounting With the Mounting Kit The mounting kit contains a mounting bracket for wall mounting or pole mounting. You can use the mounting bracket as a template to mark the positions of the mounting holes for your installation. You then install the mounting plate, and attach the Cisco LoRaWAN Interface Module when you are ready.
PAGE 12
Getting Started and Product Document of Compliance for the Cisco LoRaWAN Interface Module Pole/Wall Mounting Figure 5 Mounting Bracket for Wall or Pole Mounting 1 Quick Mount Keyhole Slots (for the Cisco LoRa Interface use) 2 Mounting Slots (used with the band clamps) 3 Bracket Mount Holes (use bolts up to 1/4" or 6 mm in diameter) 2. Use four customer-supplied screws and optional screw-anchors to attach the mounting plate to the mounting surface. 3.
PAGE 13
Getting Started and Product Document of Compliance for the Cisco LoRaWAN Interface Module Pole/Wall Mounting Pole Mounting With the Mounting Kit The mounting kit contains a mounting bracket for wall mounting or pole mounting. This kit can be used to install the Cisco LoRaWAN Interface Module on a pole. It supports metal, wood or fiberglass poles from 2 to 8 inches in diameter.
PAGE 14
Getting Started and Product Document of Compliance for the Cisco LoRaWAN Interface Module Pole/Wall Mounting Figure 6 Cisco LoRaWAN Interface Module and Fixed Mount Kit Installed on a Pole 1 Metal Band Strap 3 Pole 2 Mounting Slots 14
PAGE 15
Getting Started and Product Document of Compliance for the Cisco LoRaWAN Interface Module Grounding the Device Grounding the Device Make sure to follow any grounding requirements at your site. Warning: This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.
PAGE 16
Getting Started and Product Document of Compliance for the Cisco LoRaWAN Interface Module Regulatory Compliance and Safety Information Compliance Information Specification Description Safety IEC 60950-1 EN 60950-1 UL 60950-1 EN 60950-22 EN 50385 IEC/EN 60529 EMC Electromagnetic Emissions FCC 47 CFR Part 15 Class A EN 55022 Class A Electromagnetic Immunity EN 55024 EN 301 489-1/-3 Radio EN 300 220-2 EN 300 440-2 Class A Notice for FCC Modifying the equipment without Cisco’s authorization may resu
PAGE 17
Getting Started and Product Document of Compliance for the Cisco LoRaWAN Interface Module Regulatory Compliance and Safety Information China RoHS Note: This Table is a regulatory document required for products shipped to the People’s Republic of China. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks.
PAGE 18
Getting Started and Product Document of Compliance for the Cisco LoRaWAN Interface Module Regulatory Compliance and Safety Information 18