Installation Manual

CiscouBR7200 Series Universal Broadband Router Wireless Modem Card and Subsystem Installation and Configuration 29
show controllers
ALPHA DRAFT - CISCO CONFIDENTIAL
bec9 = 0x00000000 rxcwsnap = 0x00005EB6 syncstat = 0x00000009
cwrP2pcodecSubsystem:: "coded" (2)
for card = "p2p" (2)
convolutional rate = 7/8
Ndata = 864
local loopback = not looped
Registers in group "ctx":
t = 0x00000000 c = 0x00000026 isr = 0x00000002
ier = 0x00000000 led = 0x000003FF
Registers in group "ctx":
tsr = 0x00000008 cr = 0x00000026 sir = 0x0000FFFF
scr = 0x000000FF isr = 0x00000004 ier = 0x00000000
ndt = 0x00000360 smcr = 0x00000072 becr = 0x0000FFFF
rscr = 0x00000001 rsdr = 0x00000000 lcr = 0x00000001
lpr = 0x00000000 errstat = 0x0000009C errsize = 0x00000020
vrssize = 0x00000058 vsyncp = 0x00000047 vrsth = 0x00000008
verth = 0x0000007F vcon = 0x00000097 msgbytes2 = 0x000000FC
rseed0 = 0x000000A9 rseed1 = 0x00000000 iocntrl = 0x000000D0
njl = 0c000000E8 njm = 0x00000005 blklen2 = 0x000000FC
jdepth = 0x00000056 rsdec = 0x00000000
cwrP2pDspSubsystem:: "dsp" (3)
for card = "p2p" (2)
num RX antennae = 2
bandwidth = 12000000 Hz
throughput = high
Ndata = 864
Codec vframe size = 16
FIR vframe size = 48
IF gain update delay = 97600 ns
cwrP2pDspDerivedParams::
num RX DSPs used = 6
x2method = no
Ntable (32 entries) =
378 729 351 486 675 162 189 594
243 108 135 270 567 756 702 432
648 621 27 459 216 513 81 0
297 540 405 783 324 810 54 837
Ptable (27 entries) =
0 768 544 160 704 320 192 96
608 64 384 800 288 416 256 672
640 32 128 352 576 512 448 224
736 480 832
Mtable (32 entries) =
0x0208 0x025C 0x001C 0x0006 0x001E 0x000E 0x002E 0x0000
0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
0x02D6 0x00DC 0x00DE 0x0000 0x0000 0x0000 0x0000 0x0000
0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
Registers in group "txseq":
c = 0x00000F15 ndata = 0x0000035F
Registers in group "rxseq":
csr = 0x0000BC81 fircmd = 0x0000FFFF ndata = 0x0000135F
crt = 0x0000069F ups = 0x0000002E ifc = 0x00000987
cwrP2pFirSubsystem:: "fir" (4)
for card = "p2p" (2)
num Rx antennae = 2
bandwidth = 12000000 Hz
N+L+nu = 11-4
outer local loopback = looped
cwrP2pFirDerivedParams::
flbusDest=0x00 lfAddr=0x0400 pktData= 0x000A
flbusDest=0x20 lfAddr=0x0400 pktData= 0x0009
flbusDest=0x00 lfAddr=0x0800 pktData= 0x0000 0x0002 0x0000 0x0000
flbusDest=0x20 lfAddr=0x0800 pktData= 0x0000 0x0004 0x0000 0x0000
flbusDest=0x00 lfAddr=0x0C00 pktData= 0x0001 0x00C0 0x00FF 0x003F
flbusDest=0x20 lfAddr=0x0C00 pktData= 0x0004 0x00E0 0x00FC 0x001F