Installation Manual

30CiscouBR7200 Series Universal Broadband Router Wireless Modem Card and Subsystem Installation and Configuration

Configuring a Wireless Modem Card

ALPHA DRAFT - CISCO CONFIDENTIAL

filbusDes=0x00 lfAddr=0x0205 pktData= 0x0000

filbusDes=0x20 lfAddr=0x0205 pktData= 0x0000

filbusDes=0x00 lfAddr=0x0201 pktData= 0x0046

filbusDes=0x20 lfAddr=0x0201 pktData= 0x0046

filbusDes=0x00 lfAddr=0x0200 pktData= 0x0002

filbusDes=0x20 lfAddr=0x0200 pktData= 0x0002

filbusDes=0x00 lfAddr=0x0204 pktData= 0x0002

filbusDes=0x20 lfAddr=0x0204 pktData= 0x0002

Filter Coefficients (looped) =

0x01D7 0x07B4 0x0241 0xFC87 0x02B7 0xFE43 0x00F2 0xFF9F

0xFFA9 0xFB20 0xF8E4 0x02E9 0xFFCE 0xFEFC 0x0169 0xFE95

0xFF1D 0xF97B 0xFAEF 0x03EA 0xFE10 0x0091 0x0039 0xFF5F

0x0016 0x0337 0x07FF 0xFF57 0xFE20 0x0251 0xFDF7 0x0192

0xFFFF 0x003F 0xFFA1 0x0073 0xFF68 0x0119 0x0068 0xFFFB

0x0143 0xFEF6 0x00CD 0xFF65 0x0079 0xFFAC 0xFF06 0xFFF5

0x00CD 0xFF2B 0x00C6 0xFF4B 0x00B3 0xFF31 0xFF4E 0x0002

0xFEE2 0x00B9 0xFF98 0x002F 0xFFFB 0xFFCD 0x0124 0x002E

0x0010 0x0251 0x05C4 0xFF86 0xFEA6 0x01AB 0xFE88 0x0122

0xFFC1 0xFC7C 0xFAE0 0x0219 0xFFDC 0xFF45 0x0104 0xFEFA

0xFF5c 0xFB4D 0xFC59 0x02D2 0xFE9B 0x0069 0x0029 0xFF8C

0x0154 0x058E 0x01A0 0xFD7F 0x01F5 0xFEBF 0x00AE 0xFFBA

0xFF32 0x0085 0xFFB5 0x0022 0xFFFC 0xFFDB 0x00D3 0x0021

0x00E9 0xFF40 0x0094 0xFF90 0x0058 0xFFC3 0xFF4C 0xFFF8

0x0094 0xFF66 0x008F 0xFF7E 0x0081 0xFF6B 0xFF80 0x0001

0xFFFF 0x002D 0xFFBC 0x0053 0xFF92 0x00CB 0x004B 0xFFFC

Registers in group "ftim":

c = 0x00000019 t = 0x00000000 nlv = 0x0000044F

slip = 0x00000000 instat = 0x00000000 inten = 0x00000003

syncdly = 0x00000001

Registers in group "fdat":

c = 0x00000019 t = 0x00000A00 nlv = 0x0000044F

flbus = 0x00000080 instat = 0x00000001 inten = 0x00000001

flbus_dat = 0x00000000 flbus_star = 0x00000000

show interfaces

Use this command to display the protocol-specific details supported by the identified interface. The

show interfaces command is also the starting point to display interface-specific configurations such

as thresholds and histograms.

Unless an error occurs, no notifications are displayed on the console.

show interfaces radio <slot number>/<port number>