Softswitch Installation and Configuration Guide

ManualsBrandsCisco Systems ManualsSwitchPGW 2200

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

Cisco PGW 2200 Softswitch Release 9.8

Software Installation and Configuration

Guide

November 2008

Text Part Number: OL-18083-01

Summary of content (436 pages)

PAGE 1
Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide November 2008 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
PAGE 2
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
PAGE 3
CONTENTS Preface ix Document Objectives Audience ix ix Related Documentation ix Obtaining Documentation and Submitting a Service Request Document Change History x x Preparing for Sun Solaris Operating System and Cisco PGW 2200 Softswitch Software Installation 1-1 Supported Platforms and Cisco Products 1-1 Solaris 10, Cisco PGW 2200 Softswitch Software Release 9.
PAGE 4
Contents Removing the Solstice DiskSuite 2-88 Installing the Log and Spool File Systems (CSCOh024) 2-89 Uninstalling the Log and Spool File System 2-97 Installing Cisco BAMS Archive Partition (CSCOh027) 2-98 Installing the Sparc-based Communications and Alarm Software Package (CSCOh026) 2-103 Installing the Opteron-based Communications Software Package (CSCOh036) 2-118 Installing the Verification Test Suite Script Package (CSCOh021) 2-129 Using the SunVTS Test Package 2-131 Normal Unit Test 2-131 Running a
PAGE 5
Contents Adding a User with Minimal MML Privileges 4-12 Configuring SNMP Support Resources 4-13 Migrating the SNMP Configuration to a More Secure Environment (for Cisco PGW 2200 Softswitch Release 9.
PAGE 6
Contents Verifying Database Synchronization 4-87 Synchronizing Databases 4-88 Checking for Installation Errors 4-88 Reinstalling CSCOga002 4-89 Configuring Cisco ITP-Ls 4-89 Configuring Disk Monitor During Initial Software Configuration Configuring the Data Dumper 4-89 4-90 Configuring the Data Dumper to Support Cisco BAMS 4-92 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.
PAGE 7
Contents Falling Back to Solaris 8 on the Second Disk Drive 5-28 Restoring the Original Cisco PGW 2200 Softswitch Software 5-32 Falling Back to Previous Cisco PGW 2200 Softswitch Software Releases with Platform Changes Replacing Hard Disks on an Existing Solaris 10 Platform 5-33 Backup Procedure 5-34 Hard Disk Replacement Procedure 5-34 Loading the Solaris 10 Operating System 5-35 Loading the Sun Solaris 10 Operating Environment Packages Installing the Cisco PGW 2200 Softswitch 5-35 Restoring the System
PAGE 8
Contents Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.7(3) D-27 Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.6(1) D-37 Sample Uninstall Scripts E-1 Removing a Cisco PGW 2200 Softswitch Software Version: Sample Output for uninstall.
PAGE 9
Preface This preface describes the objectives of this document and explains how to find additional information on related products and services.
PAGE 10
Preface http://www.cisco.com/en/US/products/hw/vcallcon/ps2027/products_documentation_roadmaps_list.
PAGE 11
CH A P T E R 1 Preparing for Sun Solaris Operating System and Cisco PGW 2200 Softswitch Software Installation This chapter provides checklists describing the required and optional components, software media, and information you must have on hand before installing the Sun Solaris operating system and the Cisco PGW 2200 Softswitch software: • Note Cisco PGW 2200 Softswitch Release 9.
PAGE 12
Chapter 1 Preparing for Sun Solaris Operating System and Cisco PGW 2200 Softswitch Software Installation Solaris 10, Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Software Release Preinstallation Checklists Note The target machine must have a terminal connected to the console port by means of a serial cable. Required Software Media Gather all of the appropriate software media listed in Table 1-1. For more information, see the appropriate Sun documentation that shipped with your system.
PAGE 13
Chapter 1 Preparing for Sun Solaris Operating System and Cisco PGW 2200 Softswitch Software Installation Solaris 10, Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Software Release Preinstallation Required Site-Specific Information Your system site administrator can provide the required site-specific information in Table 1-2. Use the Notes column in this table to record the information.
PAGE 14
Chapter 1 Preparing for Sun Solaris Operating System and Cisco PGW 2200 Softswitch Software Installation Solaris 10, Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Software Release Preinstallation Checklists Table 1-4 Check Tasks Checklist Tasks Make sure that the target machine is connected to a terminal by a serial cable inserted into the console port.
PAGE 15
CH A P T E R 2 Installing the Sun Solaris 10 Operating System This chapter provides instructions for installing the packages that create the Sun Solaris 10 operating system and its operating environment on the Sun Netra and Sun Fire platforms. The following sections contain these instructions. Note Note In the following procedures, your responses to prompts sometimes depend on the disk drive size or other particulars of your system. These are pointed out as you follow the procedures.
PAGE 16
Chapter 2 Installing the Sun Solaris 10 Operating System Before You Start Before You Start Be sure to read the following cautions, notes, and tips before installing the Sun Solaris 10 operating system and the operating environment. Cautions, Notes, and Tips Note The procedures in this chapter require a working knowledge of the system administration procedures for the Sun Solaris (UNIX) operating system.
PAGE 17
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System • Installing the Solstice DiskSuite (CSCOh023), page 2-77 • Installing the Log and Spool File Systems (CSCOh024), page 2-89 • Installing Cisco BAMS Archive Partition (CSCOh027), page 2-98 • Installing the Sparc-based Communications and Alarm Software Package (CSCOh026), page 2-103 • Installing the Opteron-based Communications Software Package (CSCOh036), page 2-118 • Installing the Verification
PAGE 18
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System b. When the machine prompts for a password, type either ^ -d to proceed with normal startup, or the root password for system maintenance. Step 3 Load the appropriate version of the CD-ROM labeled Cisco Solaris 10 Operating System Jumpstart Disk for Sparc-based Platforms into the CD-ROM drive. Step 4 If the system is currently running, log in as root.
PAGE 19
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Skipped interface bge0 Beginning system identification... Searching for configuration file(s)... Search complete. Discovering additional network configuration... Completing system identification... Starting remote procedure call (RPC) services: done. System identification complete. Starting Solaris installation program... Searching for JumpStart directory...
PAGE 20
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System - Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selecting Selec
PAGE 21
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System - Selecting package (SUNWpd) Selecting package (SUNWced) Selecting package (SUNWcart200) Selecting package (SUNWkvmt200) Selecting package (SUNWust1) Selecting package (SUNWatfsr) Selecting package (SUNWatfsu) Selecting package (SUNWrcmdr) Selecting package (SUNWrcmds) Selecting package (SUNWxcu4) Selecting package (SUNWefc) Selecting package (SUNWglmr) Selecting package (SUNWi2cr) Selecting package (SUNW
PAGE 22
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System SUNWlibms........................done. SUNWxwfnt........................done. SUNWxwdv.........................done. SUNWxwplr........................done. SUNWperl584core..................done. SUNWperl584usr...................done. SUNWesu..........................done. SUNWcpp..........................done. SUNWdtcor........................done. SUNWxwplt........................done. SUNWlibC..........
PAGE 23
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System SUNWwsr2.........................done. SUNWlxml.........................done. SUNWlexpt........................done. SUNWxge..........................done. SUNWxcu4.........................done. SUNWxwacx........................done. SUNWsprot........................done. SUNWzfskr........................done. SUNWzfsr.........................done. SUNWsmapi........................done. SUNWzfsu...........
PAGE 24
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System SUNWglmr.u.......................done. SUNWi2cr.u.......................done. SUNWloc..........................done. SUNWpstl.u.......................done. SUNWus.u.........................done. SUNWbtool........................done. SUNWjfca.........................done. SUNWjfcau........................done. SUNWjss..........................done. SUNWkey..........................done. SUNWatfsr.........
PAGE 25
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System SUNWrge..........................done. SUNWroute........................done. SUNWrpcib........................done. SUNWrsgk.........................done. SUNWsolnm........................done. SUNWsshcu........................done. SUNWsshdr........................done. SUNWsshdu........................done. SUNWspnego.......................done. SUNWsshr.........................done. SUNWsshu...........
PAGE 26
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Sun Fire V210, No Keyboard Copyright 2005 Sun Microsystems, Inc. All rights reserved. OpenBoot 4.18.5, 2048 MB memory installed, Serial #52030991. Ethernet address 0:3:ba:19:ee:f, Host ID: 8319ee0f.
PAGE 27
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Installing the Sun Solaris 10 Operating System for Opteron-based Platforms The instructions in this section were written to correspond with the instructions in the Cisco Solaris 10 Operating System Startup Disk for Opteron-based Platforms. Other Solaris installations are similar, with slight variations. These instructions will note the differences between the sets of installation instructions.
PAGE 28
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System f. Save your changes and exit the Setup menu. Information similar to the following is displayed: SSC Alert: Host System has Reset screen not found. keyboard not found. Keyboard not present. Caution Using ttya for input and output. Ensure that the selected display device is set to the corresponding console device. If you use a monitor, choose solaris. If you use serial console, select solaris ttya.
PAGE 29
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System - Selecting cluster (SUNWCssh) Selecting cluster (SUNWCpool) Selecting cluster (SUNWCvld) Selecting cluster (SUNWCfwshl) Selecting cluster (SUNWClu) Selecting cluster (SUNWCcpc) Selecting cluster (SUNWCsea) Selecting cluster (SUNWCstl) Selecting cluster (SUNWCmip) Selecting cluster (SUNWCqos) Selecting cluster (SUNWCzone) Selecting cluster (SUNWCzebra) Deselecting package (SUNWauda) Deselecting package (S
PAGE 30
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System - Selecting package (SUNWinst) Selecting package (SUNWi15rf) Selecting package (SUNWipc) Selecting package (SUNWmdbr) Selecting package (SUNWmfrun) Selecting package (SUNWrsg) Selecting package (SUNWrsgk) Selecting package (SUNWter) Selecting package (SUNWtoo) Selecting package (SUNW1394) Selecting all disks Configuring boot device Using disk (c1t0d0) for "rootdisk" Deleting Solaris fdisk partition (c1t0
PAGE 31
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Warning: 1062 sector(s) in last cylinder unallocated /dev/rdsk/c1t0d0s5:116599770 sectors in 18978 cylinders of 48 tracks, 128 sectors 56933.5MB in 1187 cyl groups (16 c/g, 48.00MB/g, 5824 i/g) super-block backups (for fsck -F ufs -o b=#) at: 32, 98464, 196896, 295328, 393760, 492192, 590624, 689056, 787488, 885920, Initializing cylinder groups: .......................
PAGE 32
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add link /dev/ipsecesp=../devices/pseudo/ipsecesp@0:ipsecesp c devices/pseudo/keysock@0:keysock (136, 0) 0666 root sys link /dev/keysock=..
PAGE 33
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Installation of was successful. Installation of was successful. 22155 blocks Installation of was successful. 440 blocks Installation of was successful. 63 blocks Installation of was successful. 3 blocks Installation of was successful. 8688 blocks Installation of was successful.
PAGE 34
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Installation of was successful. 687 blocks Installation of was successful. 694 blocks Installation of was successful. Installation of was successful. 6063 blocks Installation of was successful. 134 blocks Installation of was successful. 173 blocks Installation of was successful.
PAGE 35
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Installation of was successful. 1498 blocks Installation of was successful. 4857 blocks Reboot client to install driver. Installation of was successful. 2431 blocks Reboot client to install driver. Installation of was successful. 599 blocks Installation of was successful. 1085 blocks Installation of was successful.
PAGE 36
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Reboot client to install Reboot client to install Reboot client to install Reboot client to install Reboot client to install Reboot client to install Reboot client to install Reboot client to install Reboot client to install Removing empty OWconfig driver. driver. driver. driver. driver. driver. driver. driver. driver. Installation of was successful.
PAGE 37
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System 2429 blocks Reboot client to install driver. Installation of was successful. 1423 blocks Installation of was successful. 95 blocks Installation of was successful. 40 blocks Installation of was successful. 1198 blocks Installation of was successful. Installation of was successful.
PAGE 38
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System 671 blocks Installation of was successful. 1251 blocks Reboot client to install driver. Installation of was successful. 2194 blocks Installation of was successful. 24616 blocks Installation of was successful. 1022 blocks Installation of was successful. 1830 blocks Installation of was successful. 596 blocks Reboot client to install driver.
PAGE 39
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Installation of was successful. 606 blocks Installation of was successful. Installation of was successful. 1366 blocks Installation of was successful. 878 blocks Installation of was successful. 4985 blocks Installation of was successful. Reboot client to install driver. Installation of was successful.
PAGE 40
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Installation of was successful. 231 blocks Installation of was successful. 184 blocks Installation of was successful. 928 blocks Installation of was successful. 314 blocks Installation of was successful. 228 blocks Reboot client to install driver. Installation of was successful. 10159 blocks Installation of was successful.
PAGE 41
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Installation of was successful. Modifying /a/etc/hba.conf Installation of was successful. 3366 blocks Installation of was successful. 537 blocks Reboot client to install driver. Installation of was successful. 312 blocks Installation of was successful. 803 blocks Reboot client to install driver. Installation of was successful.
PAGE 42
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System 497 blocks Installation of was successful. 271 blocks Reboot client to install driver. Installation of was successful. 145 blocks Installation of was successful. 89 blocks Reboot client to install driver. Installation of was successful. 125 blocks Installation of was successful.
PAGE 43
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System SUNWsshu SUNWlibC SUNWj5rt SUNWwbsup SUNWinstall-patch-utils-root SUNWswmt SUNWmdr SUNWmdu SUNWadmc SUNWnfsckr SUNWnfscr SUNWnfscu SUNWkrbr SUNWkrbu SUNWbip SUNWtnetc SUNWrcmdc SUNWib SUNWtavor SUNWtcsh SUNWtecla SUNWter SUNWpr SUNWtls SUNWtnetd SUNWtnetr SUNWtnfc SUNWtnfd SUNWtoo SUNWucbt SUNWudaplr SUNWudaplu SUNWipoib SUNWudapltu SUNWudapltr SUNWocfr SUNWocf SUNWos86r SUNWrmodr CADP160 SUNWaudd SUNWusb
PAGE 44
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System SUNWadp SUNWradpu320 SUNWadpu320 SUNWamr SUNWsprot SUNWrsg SUNWgssdh SUNWgssk SUNWxge SUNWbtool SUNWcslr SUNWidnl SUNWinst SUNWintgige SUNWipc SUNWipfr SUNWipfu SUNWlur SUNWluu SUNWiscsir SUNWiscsiu SUNWloc SUNWnisr SUNWnisu SUNWzebrar SUNWzebrau SUNWzip SUNWzoner SUNWluzone SUNWpoolr SUNWpool SUNWzoneu SUNWzsh SYMhisl SUNWcpc SUNWbindr SUNWbind SUNWbipr SUNWcadp SUNWced SUNWcfcl SUNWcfclr SUNWluxop SUNWc
PAGE 45
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System SUNWsasnm SUNWsadmi SUNWsacom SUNWmipr SUNWmipu SUNWmkcd SUNWfchbar SUNWfchba SUNWfcip SUNWfcmdb SUNWfcp SUNWfcprt SUNWfcsm SUNWfmd SUNWfss SUNWnge SUNWpkgcmdsr SUNWpkgcmdsu SUNWpsdcr SUNWsolnm SUNWpsdir SUNWqlc SUNWqos SUNWqosu SUNWrmodu SUNWroute SUNWrpcib SUNWrsgk SUNWrtls SUNWspnego Customizing system files - Mount points table (/etc/vfstab) fd/dev/fdfd- no /proc-/procproc- no /dev/dsk/c1t0d0s3--swap-n
PAGE 46
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Completed profile begin script.
PAGE 47
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System - Selecting package (SUNWmkcd) Selecting package (SUNWspnego) Selecting package (SUNWtnfc) Selecting package (SUNWtnfd) Selecting package (SUNWbind) Selecting package (SUNWbindr) Selecting package (SUNWctpls) Selecting package (SUNWfss) Selecting package (SUNWgcmn) Selecting package (SUNWgssdh) Selecting package (SUNWgssk) Selecting package (SUNWinst) Selecting package (SUNWi15rf) Selecting package (SUNWi
PAGE 48
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System 3149856, 3248288, 3346720, 3445152, 3543584, 3642016, 3740448, 3838880, 3937312, 4035744 - Creating /var (c1t0d0s1) Warning: 4866 sector(s) in last cylinder unallocated /dev/rdsk/c1t0d0s1:10249470 sectors in 1669 cylinders of 48 tracks, 128 sectors 5004.6MB in 105 cyl groups (16 c/g, 48.
PAGE 49
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add add c devices/pseudo/tcp@0:tcp (42, 2) 0666 root sys link /dev/tcp=../devices/pseudo/tcp@0:tcp c devices/pseudo/tcp6@0:tcp6 (142, 3) 0666 root sys link /dev/tcp6=..
PAGE 50
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Installation of was successful. 3826 blocks Installation of was successful. Installation of was successful. 5495 blocks Installation of was successful. Installation of was successful. Installation of was successful. 22155 blocks Installation of was successful. 440 blocks Installation of was successful.
PAGE 51
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Installation of was successful. 3755 blocks Installation of was successful. Installation of was successful. 554 blocks Installation of was successful. 11613 blocks Installation of was successful. 687 blocks Installation of was successful. 694 blocks Installation of was successful.
PAGE 52
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System 8 blocks Installation of was successful. 3840 blocks Installation of was successful. 259 blocks Installation of was successful. 237 blocks Installation of was successful. 1498 blocks Installation of was successful. 4857 blocks Reboot client to install driver. Installation of was successful. 2431 blocks Reboot client to install driver.
PAGE 53
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Installation of was successful. 559 blocks Reboot client to install driver. Installation of was successful. Installation of was successful. 974 blocks Installation of was successful. 1580 blocks Reboot client to install driver. Reboot client to install driver. Reboot client to install driver. Reboot client to install driver. Reboot client to install driver.
PAGE 54
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System 379 blocks Reboot client to install driver. Installation of was successful. 679 blocks Reboot client to install driver. Installation of was successful. 8309 blocks Installation of was successful. 2429 blocks Reboot client to install driver. Installation of was successful. 1423 blocks Installation of was successful.
PAGE 55
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Installation of was successful. 2519 blocks Installation of was successful. 190 blocks Installation of was successful. 453 blocks Installation of was successful. 671 blocks Installation of was successful. 1251 blocks Reboot client to install driver. Installation of was successful. 2194 blocks Installation of was successful.
PAGE 56
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Installation of was successful. 45 blocks Installation of was successful. 4056 blocks Installation of was successful. 267 blocks Installation of was successful. 9 blocks Installation of was successful. 606 blocks Installation of was successful. Installation of was successful.
PAGE 57
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System 918 blocks Installation of was successful. 29 blocks Reboot client to install driver. Installation of was successful. 215 blocks Installation of was successful. 128 blocks Installation of was successful. 231 blocks Installation of was successful. 184 blocks Installation of was successful.
PAGE 58
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System 328 blocks Installation of was successful. 40 blocks Installation of was successful. 468 blocks Installation of was successful. 844 blocks Installation of was successful. Modifying /a/etc/hba.conf Installation of was successful. 3366 blocks Installation of was successful. 537 blocks Reboot client to install driver.
PAGE 59
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Installation of was successful. 387 blocks Installation of was successful. 136 blocks Installation of was successful. 2 blocks Installation of was successful. 497 blocks Installation of was successful. 271 blocks Reboot client to install driver. Installation of was successful. 145 blocks Installation of was successful.
PAGE 60
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System SUNWadmr SUNWadmap SUNWgssc SUNWgss SUNWopenssl-libraries SUNWsshcu SUNWsshdu SUNWdtdmr SUNWtltk SUNWgzip SUNWsshr SUNWsshu SUNWlibC SUNWj5rt SUNWwbsup SUNWinstall-patch-utils-root SUNWswmt SUNWmdr SUNWmdu SUNWadmc SUNWnfsckr SUNWnfscr SUNWnfscu SUNWkrbr SUNWkrbu SUNWbip SUNWtnetc SUNWrcmdc SUNWib SUNWtavor SUNWtcsh SUNWtecla SUNWter SUNWpr SUNWtls SUNWtnetd SUNWtnetr SUNWtnfc SUNWtnfd SUNWtoo SUNWucbt SU
PAGE 61
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System SUNWvldu SUNWbash SUNWproduct-registry-root SUNWwsr2 SUNWaac SUNWaccr SUNWaccu SUNWgrub SUNWadmfr SUNWadmfw SUNWi15rf SUNWadp SUNWradpu320 SUNWadpu320 SUNWamr SUNWsprot SUNWrsg SUNWgssdh SUNWgssk SUNWxge SUNWbtool SUNWcslr SUNWidnl SUNWinst SUNWintgige SUNWipc SUNWipfr SUNWipfu SUNWlur SUNWluu SUNWiscsir SUNWiscsiu SUNWloc SUNWnisr SUNWnisu SUNWzebrar SUNWzebrau SUNWzip SUNWzoner SUNWluzone SUNWpoolr SUNWp
PAGE 62
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System SUNWlldap SUNWlsimega SUNWmdb SUNWmdbdm SUNWmdbr SUNWdtrc SUNWdtrp SUNWfctl SUNWemlxs SUNWemlxu SUNWmibii SUNWsasnm SUNWsadmi SUNWsacom SUNWmipr SUNWmipu SUNWmkcd SUNWfchbar SUNWfchba SUNWfcip SUNWfcmdb SUNWfcp SUNWfcprt SUNWfcsm SUNWfmd SUNWfss SUNWnge SUNWpkgcmdsr SUNWpkgcmdsu SUNWpsdcr SUNWsolnm SUNWpsdir SUNWqlc SUNWqos SUNWqosu SUNWrmodu SUNWroute SUNWrpcib SUNWrsgk SUNWrtls SUNWspnego Customizing sy
PAGE 63
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Installing boot information - Updating boot environment configuration file - Installing boot blocks (c1t0d0) Installation complete Executing SolStart postinstall phase... Executing finish script "patch_finish"... Finish script patch_finish execution completed. Executing JumpStart postinstall phase... all finished Finish script any_finish execution completed. The begin script log 'begin.
PAGE 64
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System This system is configured with NFS version 4, which uses a domain name that is automatically derived from the system's name services. The derived domain name is sufficient for most configurations. In a few cases, mounts that cross different domains might cause files to be owned by "nobody" due to the lack of a common domain name.
PAGE 65
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Step 4 Note Reboot your system using the method identified for your platform type: • Sparc-based platforms—Enter the boot command and press Enter to reboot the system. • Opteron-based platforms—Press any key to reboot the system.
PAGE 66
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Note On Opteron-based platforms, you can select a terminal type from the picklist, or the default terminal type (from the serial port) is used. We recommend that you use the default terminal while you are installing software. Enter the number that corresponds to the terminal you are using and press Enter. For example, if you are using an X terminal emulator, type 12 and press Enter.
PAGE 67
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Note Caution Step 7 This screen may show a different interface, depending on the platform and PCI card that are installed. For details, see Table 2-1 on page 2-3 (“Device Names on Supported Host Platforms”). The interface configuration prompts do not provide an option to return to a previous step or exit interface configuration.
PAGE 68
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Text similar to the following is displayed: - Host Name for bge0 ----------------------------------------------------------Enter the host name which identifies this system on the network. The name must be unique within your domain; creating a duplicate host name will cause problems on the network after you install Solaris.
PAGE 69
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System System part of a subnet ----------------------[X] Yes [ ] No ------------------------------------------------------------------------------ESC-2_Continue ESC-6_Help Note If you need to modify your IP addresses after you have installed Sun Solaris 10, there are three files you need to update, instead of the two files required in previous releases of Sun Solaris operating system software.
PAGE 70
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System ------------------------------------------------------------------------------ESC-2_Continue ESC-6_Help Note Step 15 The system takes approximately 30 seconds to process this selection. A countdown appears in the display after you activate your choice. Verify that No is selected and press ESC-2 to continue.
PAGE 71
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Primary network interface: Yes Use DHCP: No Host name: va-host IP address: 10.74.49.153 System part of a subnet: Yes Netmask: 255.255.255.224 Enable IPv6: No Default Route: Specify one Router IP Address: 10.74.49.129 ------------------------------------------------------------------------------ESC-2_Continue ESC-4_Change ESC-6_Help Step 18 Note Confirm the information displayed.
PAGE 72
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System - Name Service ---------------------------------------------------------------On this screen you must provide name service information. Select the name service that will be used by this system, or None if your system will either not use a name service at all, or if it will use a name service not listed here. > To make a selection, use the arrow keys to highlight the option and press Return to mark it [X].
PAGE 73
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Name service: NONE Domain name: Server address(es): Search domain(s): yourdomain.com ------------------------------------------------------------------------------ESC-2_Continue ESC-4_Change ESC-6_Help Step 25 Confirm your previous answers and press ESC-2 to continue.
PAGE 74
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System x x x x x v [ [ [ [ [ [ ] ] ] ] ] ] Belize Bolivia Brazil Canada Cayman Islands Chile press Return to mark it [X]. ------------------------------------------------------------------------------ESC-2_Continue ESC-6_Help b. Use the arrow keys to move the cursor to United States and press the spacebar to select it, then press ESC-2 to continue.
PAGE 75
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System - Confirm Information --------------------------------------------------------> Confirm the following information. If it is correct, press F2; to change any information, press F4.
PAGE 76
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Initializing Initializing 992MB of memory at addr 1024MB of memory at addr 1000000000 0 Rebooting with command: boot Boot device: /pci@1c,600000/scsi@2/disk@0,0:a File and args: SunOS Release 5.10 Version Generic_118833-17 64-bit Copyright 1983-2005 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms.
PAGE 77
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Step 3 Mount the CD-ROM in the cdrom directory by entering the following command: # mount -F hsfs -o ro /dev/dsk/devname /cdrom Where devname is the device name for the primary CD-ROM drive. The following device names are valid: Step 4 Step 5 • c0t0d0s0—Device name for primary CD-ROM on a Sparc-based platform. • c0t0d0p0—Device name for primary CD-ROM on an Opteron-based platform.
PAGE 78
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Installing SunVTS Framework (Root) as ## Installing part 1 of 1. /etc/opt/SUNWvts/sunvts.conf.example [ verifying class ] Copyright 2006 Sun Microsystems, Inc. Use is subject to license terms. All rights reserved. Installation of was successful. Adding Processing package instance from SunVTS for Tests(sparc) 6.2,REV=2006.05.04.11.
PAGE 79
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System /opt/SUNWexplo/tools/vxfs /opt/SUNWexplo/tools/vxvm [ verifying class ] ## Executing postinstall script. /usr/bin/catman is not available for use Please run: catman -w -M /opt/SUNWexplo/man manually Installation of was successful. Adding Processing package instance from Sun(TM) Explorer Data Collector Config Files(all) 5.5,REV=2006.07.14.01.
PAGE 80
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System ## Executing postinstall script. Installation of was successful. Adding Processing package instance from Solaris Print - Client, (root)(sparc) 13.1,REV=2005.01.21.15.53 Using as the package base directory. ## Processing package information. ## Processing system information. 10 package pathnames are already properly installed.
PAGE 81
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Sudo - superuser do(sparc) 1.6.8.5,REV=2006.03.26.16.30 Using as the package base directory. ## Processing package information. ## Processing system information. Installing Sudo - superuser do as ## Installing part 1 of 1. /opt/sfw/READMEs/README.SFWsudo /opt/sfw/bin/sudo /opt/sfw/etc/sudoers /opt/sfw/man/man1m/sudo.1m /opt/sfw/man/man1m/visudo.1m /opt/sfw/man/man4/sudoers.
PAGE 82
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System SUCH DAMAGE. YOU MUST OBSERVE ANY AUTHORS' CONDITIONS WITH RESPECT TO INDIVIDUAL COMPONENTS PROVIDED WITHIN THIS CODE. SUPPORT FOR THE TECHNOLOGIES AND DOCUMENTATION IS NOT PROVIDED BY SUN MICROSYSTEMS, INC.
PAGE 83
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System 119963-08 Checking installed patches... Verifying sufficient filesystem capacity (dry run method)... Installing patch packages... Patch 119963-08 has been successfully installed. See /var/sadm/patch/119963-08/log for details Patch packages installed: SUNWlibC Validating patches... Loading patches installed on the system... Done! Loading patches requested to install.
PAGE 84
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System Done! The following requested patches have packages not installed on the system Package SUNWarc from directory SUNWarc in patch 118833-36 is not installed on the system. Changes for package SUNWarc will not be applied to the system. Package SUNWarcr from directory SUNWarcr in patch 118833-36 is not installed on the system. Changes for package SUNWarcr will not be applied to the system. ...
PAGE 85
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating System SUNWmdbr SUNWmdr SUNWmdu SUNWnfsckr SUNWnfscr SUNWnfscu SUNWnisu SUNWopenssl-commands SUNWopenssl-libraries SUNWpcu SUNWpd SUNWpiclu SUNWpsu SUNWqos SUNWrcmdc SUNWroute SUNWrpcib SUNWsacom SUNWses SUNWsmapi SUNWssad SUNWtavor SUNWtoo SUNWudapltr SUNWudapltu SUNWuedg SUNWugen SUNWuksp SUNWuprl SUNWusb SUNWusbs SUNWwbsup SUNWxcu4 SUNWxge Completed installation of core extra packages Start core hardening Chan
PAGE 86
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Step 7 Remove the CD from the CD-ROM drive. This completes the installation of platform-specific data. Proceed to the “Loading the Sun Solaris 10 Operating Environment” section on page 2-72. Loading the Sun Solaris 10 Operating Environment This section contains the procedures used to load the software packages that create the Sun Solaris 10 operating environment on your host platforms.
PAGE 87
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Installing the Sparc-based Solaris 10 Patches Package (CSCOh022) To install the Sparc-based Solaris 10 Operating System Patches package (CSCOh022): Step 1 If you are using the CD-ROM, load the Cisco Solaris 10 Operating Environment CD into the CD-ROM drive. Enter the following command # pkgadd -d /cdrom/cdrom0/CSCOh022.
PAGE 88
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment The system lists the patches that it will install. This list will vary over time. A screen similar to the following is displayed: …. !! !! !! !! You must now change directories to /opt/sun_install and run the installPatches.sh script as root. Installation of was successful.
PAGE 89
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Note If you used the CD-ROM drive to load the Solaris 10 patch cluster, eject the CD prior to rebooting. This completes the procedures for installing the Solaris 10 patches for Sparc-based platforms. Go to Table 2-2 on page 2-72 if you want to continue with the list for package installation.
PAGE 90
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Using as the package base directory. ## Processing package information. ## Processing system information. 10 package pathnames are already properly installed. ## Verifying disk space requirements. ## Checking for conflicts with packages already installed. ## Checking for setuid/setgid programs.
PAGE 91
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment not indicate a problem. Please look at the log file after the rest of the patches are applied Install Solaris 10 patches from set 2 ... Changed to /var/tmp directory *** InstallPatches10 ends Tue Jul 8 11:14:41 GMT+8 2008 *** ************************************************* * It is necessary to reboot this machine * * for these patches to be incorporated * * the operating system.
PAGE 92
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Step 1 Load the Cisco Solaris 10 Operating Environment CD into the CD-ROM drive. Enter the following command to install the DiskSuite installation scripts: # pkgadd -d /cdrom/cdrom0/CSCOh023.pkg Text similar to the following is displayed. The following packages are available: 1 CSCOh023 Media Gateway Controller Solaris 10 DiskSuite (sparc,i386) 3.
PAGE 93
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment !! !! !! /opt/sun_install/DiskSuite and run the install_disksuite_1.sh script as root. Installation of was successful. Step 4 Change directories. Enter the following command: cd Step 5 /opt/sun_install/DiskSuite Run the first script. Enter the following command: ./install_disksuite_1.sh Text similar to the following is displayed: You are running as root - Good...
PAGE 94
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment * 14087 accessible cylinders * * Flags: * 1: unmountable * 10: read-only * * First Sector Last * Partition Tag Flags Sector Count Sector 0 2 00 8201856 4100928 12302783 1 7 00 12302784 10247232 22550015 2 5 00 0 143349312 143349311 3 3 01 0 8201856 8201855 4 0 00 22550016 50880 22600895 5 0 00 22600896 116647488 139248383 6 0 00 139248384 4100928 143349311 Mount Directory / /var /opt Do you want t
PAGE 95
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment 6 7 select modify name print label ! quit partition> Enter partition> change `6' partition change `7' partition select a predefined table modify a predefined partition table name the current table display the current table write partition map and label to the disk execute , then return table name (remember quotes): FORMAT MENU: disk - select a disk type - select (define) a disk type partit
PAGE 96
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment 0 - change `0' partition 1 - change `1' partition 2 - change `2' partition 3 - change `3' partition 4 - change `4' partition 5 - change `5' partition 6 - change `6' partition 7 - change `7' partition select - select a predefined table modify - modify a predefined partition table name - name the current table print - display the current table label - write partition map and label to the disk ! -
PAGE 97
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment d3: Mirror is setup d6: Mirror is setup d9: Mirror is setup d12: Mirror is setup d15: Mirror is setup The machine will now reboot. Wait for the system to come up. Then log in as root, cd /opt/sun_install/DiskSuite and continue by executing the script install_disksuite_2.sh Press the ENTER key to continue: Step 7 Press Enter to reboot your system.
PAGE 98
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment mirror to the second disk. It will take some time for the disk to be completely mirrored.
PAGE 99
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment nvramrc=devalias backup_root /pci@1f,0/pci@1/scsi@8/disk@1,0 Then bring the machine down to the boot prompt # /usr/sbin/shutdown -g0 -y -i0 .... system shuts down.... ok boot backup_root The machine should reboot from the second disk. The following text will be found in the boot output.
PAGE 100
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Disk1 is a system-maintained standard for the system's second hard disk. Note a. If the prtconf command returns the above information, you can use it to boot the second disk without any additional changes. Proceed to Step 4. b.
PAGE 101
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment . Executing last command: boot disk1 Boot device: /pci@1f,0/pci@1/scsi@8/disk@1,0 File and args: SunOS Release 5.10 Version Generic_108528-13 64-bit Copyright 1983-2004 Sun Microsystems, Inc. All rights reserved. The machine should reboot from the second disk. Step 6 Verify that the following text is displayed in the boot output (see the output in Step 4, above).
PAGE 102
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment d12: Mirror Submirror 0: d10 State: Okay Submirror 1: d11 State: Okay Pass: 1 Read option: roundrobin (default) Write option: parallel (default) Size: 116599770 blocks (55 GB) ... d14: Submirror of d15 State: Okay Size: 4096575 blocks (2.
PAGE 103
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment This procedure un-mirrors the disk partitions and removes the DiskSuite application from the platform. Use this procedure if a system has DiskSuite installed and you no longer wish to use CSCOh024 to configure the second disk for the log and spool directories.
PAGE 104
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment To determine whether DiskSuite is installed and configured, run the /usr/sbin/metastat command. If the command is found and it displays the status of mirrors, it indicates that DiskSuite is installed and configured. Note For the device names for each platform type, see Table 2-1 on page 2-3 (Device Names on Supported Host Platforms).
PAGE 105
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Table 2-4 Step 1 18-GB Disk 2 Partition Table (Cisco PGW 2200 Softswitch with Log and Spool Package) (continued) 5 0.00 6 0.00 7 0.00 Load the Cisco Solaris 10 Operating Environment CD into the CD-ROM drive. From the /var/tmp directory of the target machine, install the Log And Spool Software by entering the following command: # cd /var/tmp # pkgadd -d /cdrom/cdrom0/CSCOh024.
PAGE 106
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Step 4 Answer y and press Enter to install the files. Text similar to the following is displayed: ## Checking for setuid/setgid programs. This package contains scripts which will be executed with super-user permission during the process of installing this package. Do you want to continue with the installation of [y,n,?] Step 5 Type y and press Enter to continue.
PAGE 107
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment AVAILABLE DISK SELECTIONS: 0. c0t0d0 /pci@1f,4000/scsi@3/sd@0,0 1.
PAGE 108
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment analyze defect backup verify save inquiry volname ! quit format> p PARTITION MENU: 0 1 2 3 4 5 6 7 select modify name print label ! quit partition> 0 Part Tag 0 root - surface analysis defect list management search for backup labels read and display labels save new disk/partition definitions show vendor, product and revision set 8-character volume name execute , then return change
PAGE 109
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Enter partition id tag[var]: unassigned Enter partition permission flags[wm]: wm Enter new starting cyl[23157]: 0 Enter partition size[2097414b, 726c, 1024.13mb, 1.00gb]: 0c partition> 6 Part Tag Flag Cylinders Size Blocks 6 usr wm 23883 - 24608 1.
PAGE 110
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment disk type partition current format repair label analyze defect backup verify save inquiry volname ! quit format> q - select a disk select (define) a disk type select (define) a partition table describe the current disk format and analyze the disk repair a defective sector write label to the disk surface analysis defect list management search for backup labels read and display labels save new d
PAGE 111
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Uninstalling the Log and Spool File System Use the following procedure if you need to remove the Log and Spool File system from the second disk. Contact Cisco TAC if you need assistance (see the “Obtaining Documentation and Submitting a Service Request” section in the Preface). Note Step 1 You must be logged in as root to uninstall CSCOh024.
PAGE 112
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Note If you have installed the Solaris DiskSuite package (CSCOh023) on your system, the messages below are displayed during system boot. They are normal Solaris DiskSuite startup messages and do not indicate any problem with your system.
PAGE 113
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment The selected base directory must exist before installation is attempted. Do you want this directory created now [y,n,?,q] Step 3 Answer y and press Enter to create the directory. Text similar to the following is displayed: Using as the package base directory. ## Processing package information. ## Processing system information.
PAGE 114
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment The second hard drive will be reformatted by this script, all data on this drive will be lost Do you want to continue with formatting? (y or n) Installation started on Wed Jul 9 20:54:33 EDT 2008 Platform is SUNW,Sun-Fire-V210 Searching for disks...
PAGE 115
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment FORMAT MENU: disk type partition current format repair label analyze defect backup verify save inquiry volname ! quit format> p PARTITION MENU: 0 1 2 3 4 5 6 7 select modify name print label ! quit partition> 0 Part Tag 0 root - select a disk select (define) a disk type select (define) a partition table describe the current disk format and analyze the disk repair a defective sector write
PAGE 116
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Enter partition id tag[unassigned]: unassigned Enter partition permission flags[wm]: wm Enter new starting cyl[2216]: 0 Enter partition size[50880b, 5c, 4e, 24.84mb, 0.02gb]: 0c partition> 5 Part Tag Flag Cylinders Size Blocks 5 unassigned wm 2221 - 13683 55.
PAGE 117
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment disk type partition current format repair label analyze defect backup verify save inquiry volname ! quit format> q - select a disk select (define) a disk type select (define) a partition table describe the current disk format and analyze the disk repair a defective sector write label to the disk surface analysis defect list management search for backup labels read and display labels save new di
PAGE 118
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Note The installation of this package does not automatically enable ftp communications on your host. If you are installing this software on a Cisco BAMS system or if your host requires that the ftp communications be enabled, you can find instructions for enabling ftp in Step 5 of this procedure.
PAGE 119
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment /opt/sun_install/SolPkg/SUNWnfsckr.tar.gz /opt/sun_install/SolPkg/SUNWnfscr.tar.gz /opt/sun_install/SolPkg/SUNWnfscu.tar.gz /opt/sun_install/SolPkg/SUNWnfsskr.tar.gz /opt/sun_install/SolPkg/SUNWnfssr.tar.gz /opt/sun_install/SolPkg/SUNWnfssu.tar.gz /opt/sun_install/SolPkg/SUNWtftp.tar.gz /opt/sun_install/SolPkg/SUNWtftpr.tar.gz /opt/sun_install/SolPkg/SUNWvts.tar.gz /opt/sun_install/SolPkg/SUNWvtsmn.
PAGE 120
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment X Window System Optional Clients(sparc) 6.6.2.7400,REV=0.2004.12.15 Copyright 2005 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms. Using as the package base directory. ## Processing package information. ## Processing system information. 6 package pathnames are already properly installed. ## Verifying package dependencies. ## Verifying disk space requirements.
PAGE 121
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment This package contains scripts which will be executed with super-user permission during the process of installing this package. Do you want to continue with the installation of [y,n,?] y Installing FTP Server, (Root) as ## Installing part 1 of 1.
PAGE 122
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment including all modifications or additions, on a medium and in a form allowing fully working executable programs to be produced. 2. Redistributions of Source Code must retain the copyright notices as they appear in each Source Code file and the COPYRIGHT file, these license terms, and the disclaimer/limitation of liability set forth as paragraph 6 below. 3.
PAGE 123
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment 7. USE, MODIFICATION, OR REDISTRIBUTION, OF THIS SOFTWARE IMPLIES ACCEPTANCE OF ALL TERMS AND CONDITIONS OF THIS LICENSE. $Id: LICENSE,v 1.4 2000/07/01 17:42:15 wuftpd Exp $ Copyright (c) 1993, 1994 All rights reserved.
PAGE 124
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Using as the package base directory. ## Processing package information. ## Processing system information. 2 package pathnames are already properly installed. ## Verifying package dependencies. ## Verifying disk space requirements.
PAGE 125
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment /etc/opt /etc ## Updating system information. Removal of was successful. spawn pkgrm SUNWvtsts The following package is currently installed: SUNWvtsts SunVTS for Tests (sparc) 6.4,REV=2007.07.05.12.
PAGE 126
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment x SUNWvts/reloc/sunwvts/lib/locale/c/LC_MESSAGES, 0 bytes, 0 tape blocks x SUNWvts/reloc/sunwvts/lib/sparcv9, 0 bytes, 0 tape blocks spawn pkgadd -d . SUNWvts Processing package instance from SunVTS Framework(sparc) 6.4,REV=2007.07.05.10.00 Copyright 2007 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms. ## Executing checkinstall script.
PAGE 127
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment ## Installing part 1 of 1. y y y 94197 blocks Installation of was successful. x SUNWvtsr, 0 bytes, 0 tape blocks x SUNWvtsr/archive, 0 bytes, 0 tape blocks x SUNWvtsr/archive/none.bz2, 1280 bytes, 3 tape blocks x SUNWvtsr/install, 0 bytes, 0 tape blocks x SUNWvtsr/install/copyright, 93 bytes, 1 tape blocks x SUNWvtsr/install/depend, 848 bytes, 2 tape blocks x SUNWvtsr/install/i.
PAGE 128
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment ## Processing package information. ## Processing system information. 5 package pathnames are already properly installed. ## Verifying package dependencies. WARNING: The package "Documentation Tools " is a prerequisite package and should be installed. Do you want to continue with the installation of [y,n,?] y ## Verifying disk space requirements.
PAGE 129
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Patch packages installed: SUNWvts SUNWvtsts Installation of patch 137324-01 successful x SUNWnfsckr, 0 bytes, 0 tape blocks x SUNWnfsckr/archive, 0 bytes, 0 tape blocks ... x SUNWnfsckr/reloc/kernel/misc, 0 bytes, 0 tape blocks x SUNWnfsckr/reloc/kernel/misc/sparcv9, 0 bytes, 0 tape blocks spawn pkgadd -d .
PAGE 130
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Do you want to continue with the installation of [y,n,?] y Installing Network File System (NFS) client support (Root) as ## Installing part 1 of 1. 109 blocks [ verifying class ] [ verifying class ] y y y [ verifying class ] ## Executing postinstall script. Installation of was successful.
PAGE 131
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Processing package instance from Network File System (NFS) server kernel support (Root)(sparc) 11.10.0,REV=2005.01.21.15.53 Copyright 2007 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms. Using as the package base directory. ## Processing package information. ## Processing system information. 3 package pathnames are already properly installed.
PAGE 132
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Note If you need to disable the ftp communications software, use the svcadm disable ftp command. If you need to determine the status of the ftp communications software, use the svcs -a | grep ftp command. The communications and alarm software installation is now complete. Go to Table 2-2 on page 2-72 if you want to continue with the list for package installation.
PAGE 133
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment ## Verifying disk space requirements. ## Checking for conflicts with packages already installed. ## Checking for setuid/setgid programs. This package contains scripts which will be executed with super-user permission during the process of installing this package. Do you want to continue with the installation of [y,n,?] Step 3 Type y and press Enter to continue the installation.
PAGE 134
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment X Window System Optional Clients(i386) 6.6.2.7400,REV=0.2004.12.15 Copyright 2005 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms. Using as the package base directory. ## Processing package information. ## Processing system information. 6 package pathnames are already properly installed. ## Verifying package dependencies. ## Verifying disk space requirements.
PAGE 135
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment ## ## ## ## 7 package pathnames are already properly installed. Verifying package dependencies. Verifying disk space requirements. Checking for conflicts with packages already installed. Checking for setuid/setgid programs. This package contains scripts which will be executed with super-user permission during the process of installing this package.
PAGE 136
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment an irrevocable offer to provide a copy of the Source Code for up to three years at the cost of materials and delivery. Such redistributions must allow further use, modification, and redistribution of the Source Code under substantially the same terms as this license.
PAGE 137
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. 7.
PAGE 138
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
PAGE 139
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment ## Verifying package dependencies in global zone ## Processing package information. ## Removing pathnames in class /etc/opt/SUNWvts/sunvts.conf.example /etc/opt/SUNWvts/lib/conf /etc/opt/SUNWvts/lib /etc/opt/SUNWvts /etc/opt /etc ## Updating system information. Removal of was successful.
PAGE 140
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment x SUNWvts/install, 0 bytes, 0 tape blocks x SUNWvts/install/checkinstall, 971 bytes, 2 tape blocks x SUNWvts/install/copyright, 93 bytes, 1 tape blocks x SUNWvts/install/depend, 849 bytes, 2 tape blocks x SUNWvts/install/i.
PAGE 141
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Installation of was successful. ... SunVTS man pages(i386) 6.4,REV=2007.07.05.13.25 Copyright 2007 Sun Microsystems, Inc. All rights reserved. ... Installation of was successful. y y Archive: 137325-01.
PAGE 142
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Copyright 2007 Sun Microsystems, Inc. All rights reserved. ... Installation of was successful. ... Network File System (NFS) server support (Usr)(i386) 11.10.0,REV=2005.01.21.16.34 Copyright 2007 Sun Microsystems, Inc. All rights reserved. ... Installation of was successful. ... Trivial File Transfer Server(i386) 11.10.0,REV=2005.01.21.16.
PAGE 143
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment installed with this package NTP software is installed and configured. System reboot is required to activate it. Do you want to reboot now?[yes|no] Step 6 You must reboot your system for the changes to take effect.
PAGE 144
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment 1 CSCOh021 Media Gateway Controller Solaris 10 test for SPARC/Opteron (sparc,i386) 3.0(6) Select package(s) you wish to process (or 'all' to process all packages). (default: all) [?,??,q]: Note Step 3 You can also download the VTS script package (CSCOh021) from Cisco.com.
PAGE 145
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Using the SunVTS Test Package Use the SunVTS program to test the following: • CPUs • Memory • Ethernet cards Note In order for you to fully test the Ethernet ports, all Ethernet ports must be configured with valid IP addresses and connected to an Ethernet network with at least one other machine on the network.
PAGE 146
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Checking to see if rpcbind is running starting rpc services rpcbind giving rpcbind a chance to start Checking to see if vtsk is running starting vtsk giving vtsk a chance to start VTS probe output: Processor(s) CPU(cputest) CPU Test FPU(fputest) Floating Point Unit Test dtlb(dtlbtest) Data TLB Test l1cache(l1dcachetest) Level 1 Cache Test l2sram(l2sramtest) External Cache Test system(systest) System
PAGE 147
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Host Address: 10.0.49.119 Host ID: 18089793 Domain Name: e1000g2(nettest) Host_Name: Host Address: 172.16.101.119 Host ID: 18089793 Domain Name: e1000g3(netlbtest) Port Address: Unknown Host ID: 18089793 Comm.Ports asy0(serialtest) Port a -- asy0 /dev/term/a : /devices/ ... :a USB-Devices kbd(usbtest) Device information: USB Keyboard Unknown platform.
PAGE 148
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Central Processor Unit Test all ... Level 1 Data Cache Test all done System Test done Central Processor Unit Test all done Floating Point Unit Test all done Physical Memory Test ( 8064MB) ... Physical Memory Test done Network Test e1000g0 ... Network Test e1000g1 ... Network Test e1000g2 ... Network Loobpack Test e1000g3 ... DVD/CD Test c3t0d0 ... Hard Disk Test c0t3d0 20% ...
PAGE 149
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment e1000g3 Total number of network interfaces: 4 Number of DVD/CD drives : CD-ROM/DVD drives : c3t0d0 1 Number of LOM or TSALARM devices: LOM or TSALARM devices: Number of SSP devices: ALOM devices: 0 0 Number of NALM devices: NALM devices: 0 Number of (virtual) CPUs : 2 Note: Dual core CPUs count as two virtual CPUs (virtual) CPUs : CPU Amount of physical memory : 8064MB Amount of swap memory
PAGE 150
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment # cd /var/tmp Step 2 Enter the following command to start the test: # /opt/sun_install/vts_script brief Running a Test in Full Mode When run in full mode, the vts_script tests 100 percent of each disk surface. To run the test in full mode: Step 1 Change directories to the /var/tmp directory.
PAGE 151
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Table 2-5 Sample Estimates of VTS Script Execution Times (continued) Platform Type, Number of CPUs, CPU speed, VTS Amount of RAM, Number of Disks, Version Size of Disks Brief Mode Execution Time (Hours:Minutes: Seconds) Normal Mode Execution Time (Hours:Minutes: Seconds) Full Mode Execution Time (Hours:Minutes: Seconds) 6.0 Netra 440, 4, 1281 MHz, 8 GB, 4, 146 GB 0:11:00 2:32:00 12:30:00 6.
PAGE 152
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment This completes the Sparc-based Solaris 10 Patch cluster installation procedures. For Cisco PGW 2200 Softswitch Hosts: The Cisco PGW 2200 Softswitch software can now be loaded. For Cisco HSI: The Cisco HSI software can now be loaded. For Cisco BAMS: The BAMS software can now be loaded.
PAGE 153
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Figure 2-1 Step 2 System Agreement Accept the agreement in the Figure 2-1. A window similar to the one in Figure 2-2 is displayed. Figure 2-2 Create Initial Manager-level User Step 3 Enter the user ID and password and confirm the password. The default user ID/password is admin/admin. Step 4 Click the check mark button. A window similar to the one in Figure 2-3 is displayed.
PAGE 154
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Figure 2-3 Step 5 Warning Message Window Check the check box and click Yes on the warning message window. A window similar to the one in Figure 2-4 is displayed. Figure 2-4 LOM Screen This completes the LOM configuration on Sun Fire V40z platform. Cisco PGW 2200 Softswitch Release 9.
PAGE 155
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Configuring ILOM on Sun Fire X4600 Platform Configuring the Static IP Address Using the Command Line Interface (CLI) There are several options to connect to the ILOM. Use the following procedure to establish the connection to the ILOM using a serial connection. The following procedure is based on the Sun Microsystems document, Integrated Lights Out Manager (ILOM) Administration Guide, For ILOM 1.1.1.
PAGE 156
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Figure 2-5 Sun Fire X4600/X4600 M2 Server Back Panel 10/100 Ethernet port for net management 10/100/1000 Gigabit Ethernet ports (4) 271772 AC power connectors (4) Video connector Step 4 Serial management port USB connectors (2) Press Enter on the terminal device. The login prompt similar to the following is displayed.
PAGE 157
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Start ILOM Using Secure HTTP Follow the following steps to start the ILOM using secure HTTP. These steps are based on Chapter 4, “Using the WebGUI”, of the Sun Microsystems document, Integrated Lights Out Manager (ILOM) Administration Guide, For ILOM 1.1.1. You can find this document on Sun Microsystems web site at the following URL, http://docs.sun.com.
PAGE 158
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Configuring the IP Address with CLI The SP IP address configuration with CLI on Sun Netra X4200 M2 platform is the same as the configuration on Sun Fire X4600 platform. See Configuring the Static IP Address Using the Command Line Interface (CLI), page 2-141.
PAGE 159
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Figure 2-8 LAN Configuration in BIOS Setup Utility on Sun Netra X4200 M2 Platform Step 6 Choose Static in the IP Assignment. Step 7 Enter the IP address, the subnet mask, and the default gateway. Step 8 Select Commit. Step 9 Select Exit. Step 10 Highlight the Save Changes and Exit option. Then press Enter.
PAGE 160
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Figure 2-9 Sun Integrated Lights Out Manager Step 3 Click the Remote Control tab. Step 4 Choose the color settings accordingly: • 16-bit high-quality color for the fast Ethernet connection • 8-bit low-quality color for the normal Ethernet connection Step 5 Click Launch redirection. Step 6 Accept security warnings and hostname mismatch warnings if any.
PAGE 161
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Figure 2-10 Sun ILOM Remote Console This completes the ILOM configuration on the Sun Netra X4200 M2 platform. An Example of Using ILOM Here is a simple example of using ILOM to manage the Sun Netra X4200 M2 platform. You are going to use ILOM to install the Sun Solaris 10 on a Sun Netra X4200 M2 platform.
PAGE 162
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Figure 2-11 Step 4 Note System Output on ILOM Remote Control Console Choose the desired console device as shown in Figure 2-12. If you see the system output from a monitor directly connected to the Sun Netra X4200 M2 platform or from a remote control console of ILOM, choose Solaris. If you are using a serial console, choose Solaris Serial Console ttya. Cisco PGW 2200 Softswitch Release 9.
PAGE 163
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Figure 2-12 Note Console Settings of the Sun Solaris 10 Operating System Installation See detailed system output of the installation in the “Loading the Sun Solaris 10 Operating System” section on page 2-2. Cisco PGW 2200 Softswitch Release 9.
PAGE 164
Chapter 2 Installing the Sun Solaris 10 Operating System Loading the Sun Solaris 10 Operating Environment Cisco PGW 2200 Softswitch Release 9.
PAGE 165
CH A P T E R 3 Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher This chapter describes how to install Cisco PGW 2200 Softswitch and later releases of the Cisco PGW 2200 Softswitch software. This chapter contains the following sections: Note • Before You Start, page 3-1 • Installing the Cisco PGW 2200 Softswitch Software Release 9.
PAGE 166
Chapter 3 Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Before You Start Table 3-1 Installation Overview and Reference Sections Condition Action The Sun Solaris 10 operating system is not yet installed, you must first install it. Start with Chapter 2, “Installing the Sun Solaris 10 Operating System.
PAGE 167
Chapter 3 Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Releases Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Releases Note Before you begin this procedure, the Solaris 10 operating system and Solaris 10 operating environment should be already installed on your system.
PAGE 168
Chapter 3 Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Releases Step 6 Enter y to install the CSCOgu000 utilities package on this host. Step 7 The system begins to display various configuration settings for the Cisco PGW 2200 Softswitch software. We recommend that you accept the default values (by pressing Enter). You can, however, specify a different user ID and a group ID.
PAGE 169
Chapter 3 Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Releases Use supplied admin file for unattended install? [n] [y,n,?,q] c. Note Enter y and press Enter. This procedure can take approximately 1 hour to complete. Text similar to the following is displayed, showing the packages that were installed: Installation of was successful. WARNING: setting mode of
PAGE 170
Chapter 3 Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Releases Installing libengif.so Installing libhelp.so Installing libinf.so Installing libmmdb.so Installing libpem.so Installing libpolbase.so Installing libpolcomp.so Installing libpolfiles.so Installing libpolnuman.so Installing libpolroute.so Installing libpom.so Installing libpxe.so Installing libpxelog.so Installing libqbe.so Installing libqbe_v6.
PAGE 171
Chapter 3 Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Releases NOTE: Each TimesTen installation is identified by a unique instance name. The instance name must be a non-null alphanumeric string, not longer than 255 characters. Instance name will be 'tt60'.
PAGE 172
Chapter 3 Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Releases Copyright (c) 1996-2006, Oracle. All rights reserved. Type ? or "help" for help, type "exit" to quit ttIsql. All commands must end with a semicolon character. IInstallation of was successful. WARNING: setting mode of to default mode (755) Updating parameters for critagt.cnf Updating parameters for startcia.
PAGE 173
Chapter 3 Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Releases Updating Updating Updating Updating parameters parameters parameters parameters for for for for tibco.cfg tib4pgw.sh tibAdapter.pl tibsimulator.pl Installation of was successful. Installing ca Uncompressing callver Installing get_trc.
PAGE 174
Chapter 3 Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Installing the Cisco PGW 2200 Softswitch Software Release 9.
PAGE 175
Chapter 3 Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Releases b. Select the specific protocol(s) you need from the tables (instead of selecting all) and enter the protocol identifier(s). The following prompt is displayed: Would you like to add another protocol set to your system? [y] [y,n,?,q] Step 11 Select one of the following options: a.
PAGE 176
Chapter 3 Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Releases Step 14 Note You can now begin configuring your Cisco PGW 2200 Softswitch software in the “Using the Cisco MGC Environment Configuration Tool” section on page 4-8.
PAGE 177
Chapter 3 Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Releases 4 package pathnames are already properly installed. ## Verifying disk space requirements. ## Checking for conflicts with packages already installed. ## Checking for setuid/setgid programs. This package contains scripts which will be executed with super-user permission during the process of installing this package.
PAGE 178
Chapter 3 Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Releases Text similar to the following is displayed: For security reasons, ftp access is disabled by default. Do you want to allow ftp access? (y/n) [N] Step 6 If you want to allow ftp access, perform the following steps. If you do not want to allow ftp access, enter n and press Enter, then proceed to Step 7. a. Type y and press Enter.
PAGE 179
Chapter 3 Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Releases ************************************************** Do you want to reboot the machine now? (y/n) [N] Step 9 Enter y and press Enter to reboot the system and reset your security settings. Step 10 Enter eject and press Enter to open the CD-ROM drive door once the system has completed the reboot.
PAGE 180
Chapter 3 Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Releases Installing the License File if the Cisco PGW 2200 Softswitch is NOT Running If the Cisco PGW 2200 Softswitch is not in a running state, perform the following steps. Step 1 Save the license file (.lic) to a temporary directory on your hard disk.
PAGE 181
Chapter 3 Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Releases Installing on a Fault Tolerant System Caution To ensure the successful installation of a fault tolerant configuration, you must provision the software for the active Cisco PGW 2200 Softswitch host after Step 10 of the “Installing the Cisco Security Package (CSCOh020)” section on page 3-12, before proceeding to Step 1, below.
PAGE 182
Chapter 3 Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Releases Note Always check cisco.com (http://www.cisco.com/kobayashi/sw-center/sw-voice.shtml) to ensure that you have the latest required patch version released by Cisco on your system, CD, or file system (if downloaded previously from cisco.com). Cisco PGW 2200 Softswitch Release 9.
PAGE 183
CH A P T E R 4 Configuring the Cisco PGW 2200 Softswitch Software This chapter describes how to configure Release 9.8 of the Cisco PGW 2200 Softswitch software. Quick Guide to Configuring the Cisco PGW 2200 Softswitch Software Note The Cisco PGW 2200 Softswitch software files and processes are located in the /opt/CiscoMGC directory. The following table provides an overview of the Cisco PGW 2200 Softswitch software configuration.
PAGE 184
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Before You Start Table 4-1 Quick Guide to Configuring the Cisco PGW 2200 Softswitch Software (continued) Task Detailed Procedures Configuring the Execution Environment on page 4-25 – Changing XECfgParm.dat File Parameters on page 4-26 – Changing XECfgParm.
PAGE 185
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Before You Start Caution • Have your company's internal support and Cisco support contact information readily available so you can get help with the installation if needed. (If you have questions or need assistance, see the “Obtaining Documentation and Submitting a Service Request” section on page x of the Cisco support contact information.) • Ensure that you have access to the console port on your Cisco PGW 2200 Softswitch host.
PAGE 186
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Initial Cisco PGW 2200 Softswitch Software Configuration Table 4-2 Software Directory Structure (continued) Directory Contents /opt/CiscoMGC/var Contains the log, spool, trace, and Coredump file directories. /opt/CiscoMGC/var/log Default platform informational and error logs. /opt/CiscoMGC/var/spool Spool files for CDRs and measurements. /opt/CiscoMGC/var/trace Location of trace files created by using the sta-trc MML command.
PAGE 187
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Initial Cisco PGW 2200 Softswitch Software Configuration Table 4-3 shows the Cisco PGW 2200 Softswitch configuration parameters. Table 4-3 Configuration Parameters Parameter Description *.CPUTimerInterval Samples the frequency of CPU utilization. Prior to Release 9.4(1), this parameter must be set to 0 during the initial configuration of any platform with a single CPU (including Sun Netra t 100/105, Sun Netra V 120, and Sun Netra 120).
PAGE 188
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Initial Cisco PGW 2200 Softswitch Software Configuration Table 4-3 Configuration Parameters (continued) Parameter Description *.SysConnectDataAccess Controls whether data access is enabled or disabled (if the engine attempts to connect to the MMDB or to call screening database at startup). Values: • true = connect to MMDB or call screening database • false = do not connect to MMDB or call screening database Default: false Note *.TCAP.
PAGE 189
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Initial Cisco PGW 2200 Softswitch Software Configuration Table 4-3 Configuration Parameters (continued) Parameter Description engine.SysVirtualSwitch Indicates whether the Cisco PGW 2200 Softswitch host functions as a signaling controller or a virtual switch controller.
PAGE 190
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Initial Cisco PGW 2200 Softswitch Software Configuration Table 4-4 Item Note Parameters Required for Initial Setup Parameter Name Default Value Changed Values 1 *.platformId 1 2, if slave 2 *.transpathId 01 02, if standby 3 *.ownTranspathId 01 02, if standby 4 *.peerTranspathId 02 01, if standby 5 *.MGC_CDR_NODE_ID MGC-CDR-NO System Id for Call Data Records (CDRs) DE-STRING 6 *.
PAGE 191
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Initial Cisco PGW 2200 Softswitch Software Configuration A dialog box displays, warning that the MGC Environment Configuration Tool is for initial system configuration only. Note Step 2 To run the MGC Environment Configuration Tool in detail mode, enter the command MGC_Setup -detail. Click Yes to continue running the XECfg program. The MGC Environment Configuration Tool screen expands to provide information from the XECfgParm.dat file.
PAGE 192
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Initial Cisco PGW 2200 Softswitch Software Configuration Table 4-5 Step 3 Note MGC Environment Configuration Tool Startup Parameters (continued) Field Usage Call Screening Indicates whether call screening is enabled or disabled on the Cisco PGW 2200 Softswitch. This setting is optional. CLLI Code The CLLI code identifying the site where the Cisco PGW 2200 Softswitch is located. This setting is optional.
PAGE 193
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring Groups and Users If you set the Operational Mode to Active/Standby, the XECfg program displays a prompt that allows you to transfer the XECfgParm.dat.slave file to a remote machine when you exit the application. To transfer the file to a remote machine, enter the FTP password. Otherwise, exit the application. Configuring Groups and Users You must set up groups and users for the Cisco PGW 2200 Softswitch software on each host server.
PAGE 194
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring Groups and Users # useradd -u UID -g mgcgrp -d /opt/CiscoMGC/local -s /bin/csh -m username UID is a user ID that is an integer from 0 through 2147483647 (excluding the numbers 0, 1, 2, 3, 4, 5, 9, 37, 71, 60001, 60002, and 65534, because they are used by the operating system).
PAGE 195
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SNMP Support Resources Text similar to the following is displayed: Copyright ? 1998-2002, Cisco Systems, Inc. User has minimal access privileges sh-passat mml> To exit MML, type quit and press Enter. This completes the procedure for adding a user with minimal MML privileges. The group and user configuration is now complete. Continue to the “Configuring SNMP Support Resources” section on page 4-13.
PAGE 196
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SNMP Support Resources Note SNMP managers such as the Cisco Media Gateway Controller Node Manager (Cisco MNM) or HP OpenView can be used to receive traps. Note The config-snmp utility is case-sensitive. It will accept “name1” and “NAME1” as two different entries. Migrating the SNMP Configuration to a More Secure Environment (for Cisco PGW 2200 Softswitch Release 9.
PAGE 197
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SNMP Support Resources 2. Enter the following commands to restart the snmp daemon: ps -ef |grep snmpdm The system will display the process ID for the snmp daemon. Restart the daemon using the following command: kill -9 snmpdm_pid Where snmpdm_pid is the process ID for the snmp daemon. Note that the first instance of ReadAndNotifyToAll in the snmpCommunityEntry will be the only CommunityName used in the Trap.
PAGE 198
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SNMP Support Resources b. To check critagt: # ps -ef |grep critagt If the critagt process is running, text similar to the following is displayed: root 27888 1 0 May 19 ? 0:15 /opt/CiscoMGC/snmp/critagt -d Step 4 To start the config-snmp utility, enter the following commands and press Enter: # cd /opt/CiscoMGC/local # config-snmp The following screen is displayed: Migrating snmpd.cnf into a more secure setting...
PAGE 199
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SNMP Support Resources Adding an SNMP Community Entry Continuing from Step 6, above (of the section Running the config-snmp Utility): Step 1 Enter 12 to select snmpCommunityEntry and view the entries: Text similar to the following and the SNMPD Configuration Main Menu are displayed.
PAGE 200
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SNMP Support Resources ReadAndNotifyToAll usm ApplicationsView - ApplicationsView CiscoInternalSignal snmpv1 All All All CiscoInternalSignal snmpv2c All All All CiscoInternalSignal usm All All All Would you like to proceed with the Add [n]/[y]? Step 3 Enter y to proceed (if you enter n to cancel the addition, you return to the SNMPD Configuration Main Menu).
PAGE 201
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SNMP Support Resources For steps on how to execute the selections from the SNMPD Configuration Main Menu, see the following sections: • Adding an SNMP Community Entry, page 4-17 • Deleting an SNMP COMMUNITY, page 4-19 • Adding a Trap Destination, page 4-20 • Deleting a Trap Destination, page 4-22 • Activating the New Settings, page 4-23 • Verifying the SNMP Configuration Migration, page 4-24 Note To complete the migratio
PAGE 202
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SNMP Support Resources Enter snmpCommunityName: Step 3 Enter an SnmpCommunityName. Select an SnmpCommunityName from the list that is displayed in Step 1. The SnmpCommunityName T555, is an example: T555 Text similar to the following is displayed: snmpCommunityName: T555 is about to be deleted.
PAGE 203
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SNMP Support Resources =================== Add Trap Menu =================== 1. TargetAddress: 6.6.6.6:0 , TargetAddrParams: v1ExampleParams , IP Mask: 255.255.255.255:0 Would you like to proceed with the Add Step 2 [n]/[y]? Enter y to add a Trap Destination (if you enter n to cancel the addition, you return to the SNMPD Configuration Main Menu). Text similar to the following is displayed: Enter IP Address (x.x.x.
PAGE 204
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SNMP Support Resources Verifying the SNMP Configuration Migration, page 4-24 • The procedure for adding a Trap Destination is now complete. Proceed to the selection you entered in the SNMPD Configuration Main Menu.
PAGE 205
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SNMP Support Resources Step 5 Enter your selection.
PAGE 206
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SNMP Support Resources Verifying the SNMP Configuration Migration Perform the following steps to verify that your changes were applied by running the config-snmp utility: Step 1 To start the config-snmp utility, type the following command and press Enter: # config-snmp Text similar to the following is displayed: Migrating snmpd.cnf into a more secure setting...
PAGE 207
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring the Execution Environment #Entry type: snmpCommunityEntry #Format: snmpCommunityIndex (text) # snmpCommunityName (text) # snmpCommunitySecurityName (text) # snmpCommunityContextEngineID (octetString) # snmpCommunityContextName (text) # snmpCommunityTransportTag (text) # snmpCommunityStorageType (nonVolatile, permanent, readOnly) snmpCommunityEntry Icomname1 comname1 ReadWriteAll localSnmpID - - nonVolatile snmpCommunityEntry Ijammmy
PAGE 208
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring the Execution Environment • Initializing the Provisioning Object Manager, page 4-41 The configuration data file, or XECfgParm.dat file (located in /opt/CiscoMGC/etc/XECfgParm.dat), lists all the components in the Cisco PGW 2200 Softswitch software and defines how it operates. You must edit the execution environment parameters in the XECfgParm.dat file to initialize and configure the Cisco PGW 2200 Softswitch software application.
PAGE 209
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring the Execution Environment Note Do not restart the software yet if you need to configure SCP queries or initialize the call screening database. Complete the instructions in the appropriate sections of this chapter before restarting the software. Continue to “Changing XECfgParm.dat File Parameters in a Running Fault Tolerant System” to change parameters without call interruption.
PAGE 210
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring the Execution Environment Tip If Host X does not take over call processing after switchover, restart the software on Host Y to take over the calls. Check the parameters you changed on Host X and make sure you have the correct values. Configuring Basic System Information Note For a complete list of the parameters found in the XECfgParm.
PAGE 211
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring the Execution Environment Parameter Modification *.ownTranspathId To identify the local Cisco PGW 2200 Softswitch host in a fault tolerant system, enter the same value that you used for *.transpathID. If you have two Cisco PGW 2200 Softswitch hosts in a fault tolerant system, enter this value in the *.peerTranspathID field in the XECfgParm.dat file on the second host server. If you have a simplex system, leave this value blank.
PAGE 212
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring the Execution Environment Parameter Modification *.transpathId To identify the local Cisco PGW 2200 Softswitch host in a fault tolerant system, enter any one- or two-digit integer. If you have two Cisco PGW 2200 Softswitch hosts in a fault tolerant system, this number must be different in the XECfgParm.dat file for each host.
PAGE 213
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring the Execution Environment Note If there are two Ethernet interfaces defined on the Cisco PGW 2200 Softswitch, it is mandatory to have these on distinct subnets. For example, consider the following configuration: *.IP_AddrLocalA = 172.22.119.108 *.IP_AddrLocalB = 172.22.119.54 This is not a valid combination because they are on the same subnet. The following example illustrates a valid combination: *.IP_AddrLocalA = 172.22.119.
PAGE 214
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring the Execution Environment Parameter Modification *.IP_Addr1 Enter the IP address of the bge0 interface. *.IP_Addr2 Enter the IP address of the bge1 interface (if configured). *.IP_Addr3 Enter the IP address of the bge2 interface (if configured). *.IP_Addr4 Enter the IP address of the bge3 interface (if configured). *.
PAGE 215
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring the Execution Environment Parameter Modification engine.SysCdrCollection Designates the format of CDRs. Values: • true—Invalid for Release 7.4 and above. • false—Generates binary format CDRs (default) Default: false Note Do not change this value. Setting this to a value of true for Release 7.4 and higher is not valid and may have deleterious effects on the system. engine.
PAGE 216
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring the Execution Environment Setting the Call Cutoff Timer The Cisco PGW 2200 Softswitch call cutoff timer is disabled by default. To set the call cutoff timer, modify the following parameter in the XECfgParm.dat file: Parameter Modification *.CallCutoffTimer Provides a global system-wide timer, which is started when a call is answered and runs for the pre-configured time.
PAGE 217
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring the Execution Environment Configuring Call Detail Record File Output To configure call detail record (CDR) file output, modify the following parameters in the Data Dumper and Engine sections of the XECfgParm.dat file: Parameter Modification engine.CDRencodingFormat To specify the call detail record (CDR) file encoding format, enter one of the following values: engine.
PAGE 218
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring the Execution Environment Configuring the Clearing Location and Default Location Parameters The ClearingLocation and DefaultLocation parameters are used to determine a call’s location value. If you require a value other than the default to be sent to the switch, use these parameters to override the Clearing Location and Default Location fields in the Call Context.
PAGE 219
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring the Execution Environment Parameter Modification ClearingLocation This property overrides the Clearing Location field in Call Context. Change this value if you need a value other than the default to be sent to the switch. Valid values are: • 0—The Cisco PGW 2200 Softswitch software uses the default Clearing Location in Call Context.
PAGE 220
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring the Execution Environment Parameter Modification DefaultLocation This property overrides the Default Location field in Call Context. Change this value if you need to define a customer-specific default location for your system that can differ from the default location set in the type definition of the protocol.
PAGE 221
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring the Execution Environment Configuring Switchover To configure switchover, modify the following parameters in the foverd section of the XECfgParm.dat file. : Parameter Modification foverd.conn1Type To set the connection type for connection number 1, enter serial or socket. Typically, set this value to socket. Note foverd.
PAGE 222
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring the Execution Environment Parameter Modification foverd.ipLocalPortB To define the secondary local port number used for IP communication, enter a unique number, keeping the following in mind: • Typically, if Type is socket, set this value to 1053. • If you have two Cisco PGW 2200 Softswitch hosts in a switchover configuration, enter this value in the foverd.ipPeerPortB field in the XECfgParm.dat file on the secondary host.
PAGE 223
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring the Execution Environment Parameter Modification foverd.abswitchPort To specify the port used for communication with the A/B switch, enter a location; for example, /dev/term/a. Note foverd.heartbeatInterval If your configuration does not use an A/B switch, use the default value (/dev/null). Specifies the maximum time in milliseconds between heartbeat messages from the peer switchover daemon.
PAGE 224
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries Parameter Modification pom.dataSync Used in a fault tolerant system to indicate that the POM should synchronize the provisioning data at startup. • If you have a standalone system, set this value to false. • If you have a fault tolerant system, set this value to true. Caution Note If pom.
PAGE 225
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries Warning Note • Configuring the trigger.dat File Attributes, page 4-43 • Sample trigger.dat File, page 4-45 Do not edit trigger.dat file parameters that are not listed below, and remember that all parameters are case-sensitive. Otherwise, your system might not work as intended. The following Bellcore Standards are supported for US 800 toll-free services: IN/1 Toll Free Service support: GR-1428 AIN 0.
PAGE 226
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries Configuring the Translation Type Attribute Perform the following steps to configure the Translation Type (translationType) attribute: Step 1 Back up the trigger.dat file. Step 2 Determine the Trigger Number that you need to edit. You can get this information from your network administrator. Step 3 Navigate to directory /opt/CiscoMGC/etc.
PAGE 227
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries F15 F16 OS10 F14 OS9 F13 OS8 F12 OS7 F11 OS6 F10 OS5 F9 OS4 F8 OS3 F7 tcapBodyType msg F6 OS1 F5 translationType F4 asn1Encoding F3 stpScpGroupIndex F2 tcapType F1 $MessageSending Table Values OS2 Table 4-6 # MS 1: Customer 1 LNP 2 0 6 0 255 1 1 0 0 0 0 0 0 0 0 0 0 255 1 2 0 0 0 0 0 0 0 0 0 0 0 1 3 0 0 0 0 0 0 0 0 0 255 1 4 0 0 0 0 0 0 0
PAGE 228
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries #---------------------------------------------------------# TT 2: Generic LNP #---------------------------------------------------------2 2 1 3 0 0 0 0 0 0 0 0 #---------------------------------------------------------# TT 3: Genesys 800 #---------------------------------------------------------3 3 10 4 5 0 0 0 0 0 0 0 #---------------------------------------------------------# TT 4: ANSI AIN 800 NPA #-------------------
PAGE 229
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries 7 14 10 16 0 0 0 0 0 0 0 0 #---------------------------------------------------------# TT 15: INAP LNP Service (Service Key = 1) #---------------------------------------------------------7 15 10 16 0 0 0 0 0 0 0 0 #---------------------------------------------------------# TT 16: INAP Carrier Pre-Selection Service (Service Key =2) #---------------------------------------------------------7 16 10 16 0 0 0 0 0 0
PAGE 230
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries #---------------------------------------------------------14 25 0 0 0 0 0 0 0 0 0 0 #---------------------------------------------------------# TT28 : INAP CS1 Post temp-connection handling #---------------------------------------------------------15 0 0 0 0 0 0 0 0 0 0 0 #---------------------------------------------------------# TT 29 : INAP CS2 Initial DP #---------------------------------------------------------13 29
PAGE 231
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries 3 0 0 0 0 0 0 0 0 0 #------------------------------------------------# MA 9: INAP Prepaid Services InitialDP #------------------------------------------------3 0 0 0 0 0 0 0 0 0 #-------------------------------------------------------# MA 10: INAP Prepaid Services ApplyChargingReport #-------------------------------------------------------0 0 0 0 0 0 0 0 0 0 #---------------------------------------------------#
PAGE 232
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries inap-lnp-norway inap-pp-initdp inap-pp-charge-atexp inap-pp-bcsm inap-pp-charge-texp inap-pp-charge-final inap-lnp-portugal inap-cs1-initdp inap-cs1-dummy-25 inap-cs1-dummy-26 inap-cs1-dummy-27 inap-cs1-dummy-28 inap-cs2-initdp ansi-pre-ain-cnam 17 18 19 20 21 22 23 24 25 26 27 28 29 30 ############### $MessageSending ############### # # F1 F2 F3 F4 F10 F11 F12 F13 F14 F15 F16 # tcapType stpScpGroupIndex msg asn1Encodi
PAGE 233
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries #--------------------------------------------------------------------------------------------------------------------------# MS 6: ANSI AIN 800 NPA-NXX-XXX #--------------------------------------------------------------------------------------------------------------------------2 0 6 0 255 1 4 0 0 0 0 0 0 0 0 0 #---------------------------------------------------------------------------------------------------------------
PAGE 234
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries #--------------------------------------------------------------------------------------------------------------------------# MS 14: INAP InitialDP Query, Free Phone Service #--------------------------------------------------------------------------------------------------------------------------1 0 1 0 0 1 110 0 0 0 0 0 0 0 0 0 #---------------------------------------------------------------------------------------------
PAGE 235
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries #--------------------------------------------------------------------------------------------------------------------------# MS 22: INAP Prepaid Services ApplyChargingReport (Final End) #--------------------------------------------------------------------------------------------------------------------------1 0 3 0 0 3 13 0 0 0 0 0 0 0 0 0 #----------------------------------------------------------------------------------
PAGE 236
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries #--------------------------------------------------------------------------------# MS 30 : ANSI PRE AIN CNAM # tcapType=PRE AIN, msg=query with permission , asn1Encoding=asn1_definite, # tcapBodyType=sequence, OS= 19 #--------------------------------------------------------------------------------3 0 6 0 5 2 19 0 0 0 0 0 0 0 0 ################# $OperationSending ################# # # F1 F2 F7 # componentType opClass PS
PAGE 237
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries #-------------------------------------------------------------------------------------------6 1 3 1 3 0 6 #-------------------------------------------------------------------------------------------# OS 7: ANSI PRE AIN 800 Termination Information #-------------------------------------------------------------------------------------------2 1 0 0 0 0 7 #-----------------------------------------------------------------------
PAGE 238
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries #-------------------------------------------------------------------------------------------1 2 0 24 1 0 13 #-------------------------------------------------------------------------------------------# OS 15: INAP LNP for Portugal #-------------------------------------------------------------------------------------------1 1 0 0 1 0 14 #------------------------------------------------------------------------------------
PAGE 239
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries # PS 1: Customer 1 LNP #---------------------------------------------------------------------------------------------------------------------------------------------------100 1 101 1 102 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 #---------------------------------------------------------------------------------------------------------------------------------------------------# PS 2: Generic LNP #-------------------
PAGE 240
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries # PS 9: INAP Free Phone, LNP & Carrier Pre-Selection Services #---------------------------------------------------------------------------------------------------------------------------------------------------200 1 201 1 202 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 #---------------------------------------------------------------------------------------------------------------------------------------------------
PAGE 241
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries # PS 17: INAP CS1 ApplyChargingReport #---------------------------------------------------------------------------------------------------------------------------------------------------214 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 #---------------------------------------------------------------------------------------------------------------------------------------------------# PS 18: ANSI PRE AIN CNAM #
PAGE 242
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries #-------------------------------------------------------------------------------------------------# RR 7: ANSI AIN 800 #-------------------------------------------------------------------------------------------------5 6 #-------------------------------------------------------------------------------------------------# RR 8: ANSI PRE AIN 800 With termination status notification #------------------------------------------
PAGE 243
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries #-------------------------------------------------------------------------------------------------0 13 #-------------------------------------------------------------------------------------------------# RR 16: INAP Free Phone, LNP & Carrier Pre-Selection Services, Expected Response 1, End: Connect #-------------------------------------------------------------------------------------------------11 14 #---------------------
PAGE 244
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries # RR 24: INAP Prepaid Services, Expected Response (Continue, FurnishChargeInformation, ReleaseCall) #-------------------------------------------------------------------------------------------------17 18 #-------------------------------------------------------------------------------------------------# RR 25: INAP LNP for Portugal, Unexpected Response (default action) #----------------------------------------------------
PAGE 245
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries #-------------------------------------------------------------------------------------------------# RR 33: INAP CS1, Expected Response (Continue, RequestReportBCSMEvent, EstablishTemporaryConnection) #-------------------------------------------------------------------------------------------------24 24 #-------------------------------------------------------------------------------------------------# RR 34: INAP CS1, Expe
PAGE 246
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries # # F1 F2 F3 F19 F20 F21 # MSG OR1 REQ REQ OR10 REQ F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 F14 F15 F16 F17 F18 OR2 REQ OR3 REQ OR4 REQ OR5 REQ OR6 REQ OR7 REQ OR8 REQ OR9 #----------------------------------------------------------------------------------------------------# MR 1: Customer 1 LNP / Generic LNP #----------------------------------------------------------------------------------------
PAGE 247
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries # MR 8: CS1/INAP Based CLI Screening, End Message w/ Connect #----------------------------------------------------------------------------------------------------3 8 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 #----------------------------------------------------------------------------------------------------# MR 9: CS1/INAP Based CLI Screening, End Message w/ ConnectToResource, PlayAnnouncment #-------------------------------
PAGE 248
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries #----------------------------------------------------------------------------------------------------# MR 16: INAP Prepaid Services, Expected Response (Continue, Connect) #----------------------------------------------------------------------------------------------------2 13 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 #----------------------------------------------------------------------------------------------------# MR 17:
PAGE 249
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries #----------------------------------------------------------------------------------------------------4 25 0 30 0 27 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 #----------------------------------------------------------------------------------------------------# MR 24: INAP CS1 , Expected Response (RRBE, ETC, FCI) #----------------------------------------------------------------------------------------------------4 23 0 28 1 24 0 0 0 0
PAGE 250
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries ################### $OperationReceiving ################### # # F1 F2 # componentType opClass F3 F4 F5 F6 opCodeFamily opCodeSpecifier opCodeFlag PR #---------------------------------------------------------------------# OR 1: Customer 1 LNP / Generic LNP #---------------------------------------------------------------------6 1 101 1 4 1 #---------------------------------------------------------------------# OR 2: Gene
PAGE 251
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries #---------------------------------------------------------------------1 1 0 20 1 11 #---------------------------------------------------------------------# OR 13: INAP Prepaid Services, Expected Response (Connect) #---------------------------------------------------------------------1 2 0 20 1 12 #---------------------------------------------------------------------# OR 14: INAP Prepaid Services, Expected Response (ApplyC
PAGE 252
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries #---------------------------------------------------------------------# OR 25: INAP CS1, Expected Response (ReleaseCall) #---------------------------------------------------------------------1 2 0 22 1 24 #---------------------------------------------------------------------# OR 26: INAP CS1, Expected Response (CollectInformation) #---------------------------------------------------------------------1 2 0 27 1 0 #-------
PAGE 253
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries # componentType opClass 1 2 opCodeFamily opCodeSpecifier opCodeFlag PR 0 47 1 32 #---------------------------------------------------------------------# OR 37: INAP CS2, Expected Response (ConnectToResource operation) #---------------------------------------------------------------------# componentType opClass opCodeFamily opCodeSpecifier opCodeFlag PR 1 2 0 19 1 33 #----------------------------------------------------
PAGE 254
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries 205 0 0 1 0 0 1 0 0 206 0 0 1 0 0 1 0 0 204 0 0 1 0 0 3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 #-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------# PR 4: ANSI AIN 800 Result #-----------------------------------------------------------
PAGE 255
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries #-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------209 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 #--------------------------------------------------------------------------------------------------------------
PAGE 256
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries #-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------# PR 15: INAP Prepaid Services FurnishCharging Parameters #-----------------------------------------------------------------------------------------------------------------------------------------------
PAGE 257
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries 211 0 0 1 0 0 1 0 0 212 0 0 0 0 0 1 0 0 213 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 #-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------# PR 21: INAP CS1 SendChargingInformation Parameters #-----------------------------------
PAGE 258
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries # ParameterAssistingSSPIPRoutingAddress, ServiceInteractionIndicators, ItuAsn1EtcLegIDElem,ItuAsn1EtcCallSegmentIDElem,ItuAsn1EtcCarrierElem #-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------223 1 1 207 0 1 253 0 1 254 0 1 229 0 1 0 0 0 0 0 0 0 0 0 0 0
PAGE 259
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries 239 0 0 1 0 0 1 0 0 240 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 #-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------# PR 32: INAP CS1 PlayAnnouncement(InformationToSend, RequestAnnouncementComplete, LegId Ca
PAGE 260
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries #-------------------------------------------------------------------------4 1 2 0 0 0 0 0 0 0 0 0 0 0 0 #-------------------------------------------------------------------------# RA 3: Generic LNP 1st Expected #-------------------------------------------------------------------------1 1 0 4 1 2 0 0 0 0 0 0 0 0 0 #-------------------------------------------------------------------------# RA 4: Genesys (Error) #----------
PAGE 261
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries # RA 15: INAP LNP for Norway, Unexpected Response #-------------------------------------------------------------------------4 1 14 0 0 0 0 0 0 0 0 0 0 0 0 #-------------------------------------------------------------------------# RA 16: INAP LNP for Norway, Expected Response #-------------------------------------------------------------------------4 1 15 0 0 0 0 0 0 0 0 0 0 0 0 #------------------------------------------
PAGE 262
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries #-------------------------------------------------------------------------# RA 28: INAP CS2, Expected Response(DL, SL, MCS,DFCwithArg,RRBE, ML, CWA) #-------------------------------------------------------------------------4 1 20 0 0 0 0 0 0 0 0 0 0 0 0 #-------------------------------------------------------------------------# RA 29: INAP CS2, Expected Response(CTR,PA,RRBE,CWA) #-----------------------------------------
PAGE 263
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring SCP Queries #-------------------------3 0 0 0 0 # AD 7: CS1/INAP Based CLI Screeing Data for RESULT_ACTION_RE_TRIGGER_VIA_LCM_COND information # Cond Param Val Trg Pic #-------------------------2 209 1 13 10 # AD 8: CS1/INAP Based CLI Screeing Data for RESULT_ACTION_RE_TRIGGER_VIA_LCM_COND information # Cond Param Trg Pic Null #-------------------------0 209 13 10 0 # AD 9: CS1/INAP Based CLI Screeing Data for RESULT_ACTION_SEND_ACTI
PAGE 264
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Initializing the Call Screening Database # Act Null Null Null Null #-------------------------0 0 0 0 0 # AD 18: INAP LNP for Portugal Data for RESULT_ACTION_SEND_ACTION_TO_LCM information (IN_ROUTE) # Act Null Null Null Null #-------------------------3 0 0 0 0 # AD 19: INAP CS1 Data for RESULT_ACTION_SEND_ACTION_TO_LCM information (IN_RELEASE) # Act Null Null Null Null #-------------------------5 0 0 0 0 # AD 20: INAP CS1 Data for RESULT_ACTION
PAGE 265
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Initializing the Call Screening Database • Ported Numbers • Number Termination • Multiple Dial Plan • Advice of Charge II You might want to perform white and black list screening to include or exclude calls from certain numbers. You can provision white lists that specify allowed A-numbers (calling numbers) or B-numbers (called numbers). Black lists block specified A-numbers (calling numbers) or B-numbers (called numbers).
PAGE 266
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Initializing the Call Screening Database Network Requirements In most replication schemes, you need to identify the name of the host machine on which your data store resides. The operating system translates this host name to an IP address. This section describes how to configure your host names to ensure they use the correct IP addresses.
PAGE 267
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Initializing the Call Screening Database 192.168.11.2 UK-A-Netra1125-2 192.168.12.2 UK-A-Netra1125-2.hme1 UK-A-Netra1125-2 <----- Peer PGW hostname Peer Cisco PGW 2200 Softswitch Host /etc/hosts 127.0.0.1 localhost 192.168.11.2 UK-A-Netra1125-2 loghost 192.168.12.2 UK-A-Netra1125-2.hme1 192.168.11.1 UK-A-Netra1125-1 1 92.168.12.1 UK-A-Netra1125-1.
PAGE 268
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Initializing the Call Screening Database where activehost is the name (not IP address) of your active host. In the example below, the active host is hostx and the standby host is hosty. Caution Do not use IP addresses when setting up database replication. If you do, replication will fail. Example 4-2 Initializing Database Replication on the Standby Host Configuring replication for DSN=howdydb Restoring file /opt/TimesTen4.
PAGE 269
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Initializing the Call Screening Database Step 5 Enter the numan-rtrv MML command to verify that the entry you added in Step 4 was replicated to the database on the standby host. For example: mml> numan-rtrv:bwhite:custgrpid="S018",svcname="testsvc",cli="9998" Text similar to the following is displayed: M VSC-01 - Media Gateway Controller 2000-08-30 11:33:52 RTRV "session=test:bwhite" /* The cli :9998: exists.
PAGE 270
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Initializing the Call Screening Database % ./db_count.sh The output shows the rows counted in each database table: Counting the rows in each database table. CISCO.ANNOUNCEMENT < 0 > CISCO.A_CHARGE_ORIGIN < 0 > CISCO.A_NUMBERDIALPLANSELECTION < 0 > CISCO.BLACKLIST_A < 0 > CISCO.BLACKLIST_B < 0 > CISCO.CBBOOKINGINFO < 0 > CISCO.CBMONITORINGINFO < 0 > CISCO.CLIIPADDRESS < 0 > CISCO.CLIPREFIX < 0 > CISCO.FULLNUMBERTRANSLATION < 0 > CISCO.
PAGE 271
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring Cisco ITP-Ls Step 2 Check the log file for installation errors. (The log file is in the directory /var/adm/MGC_install.log.) Reinstalling CSCOga002 If you experience database errors such as an incorrect timestamp after completing the “Checking for Installation Errors” section on page 4-88, you need to reinstall the CSCOga002 package, which contains the Cisco PGW 2200 Softswitch database components.
PAGE 272
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring the Data Dumper Step 4 To change the percentage of disk usage at which alarming and disk trimming is initiated, modify the value of the diskmonitor.Threshold parameter. The default value is 80. Step 5 To change the number of days that finished CDR files are kept in the log directory, modify the value of the diskmonitor.CdrRmFinished parameter.
PAGE 273
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring the Data Dumper Table 4-7 Dumper Sink Log File Parameters Field Name Default Value Description maxRecs 1000 The maximum number of records a file can contain before it is flushed or moved to the spool area. If this value is set to 0, the number of records is unlimited. You can improve system performance by increasing the value of this record to a larger value, such as 50000.
PAGE 274
Chapter 4 Configuring the Cisco PGW 2200 Softswitch Software Configuring the Data Dumper to Support Cisco BAMS Step 8 Stop and start the newly-standby host (formerly active host). Step 9 Repeat Step 3 and Step 4 for the version of dmprSink.dat stored in this directory. Step 10 Change to the /opt/CiscoMGC/etc/active_link directory by entering the following UNIX command: # cd /opt/CiscoMGC/etc/active_link/ Step 11 Repeat Step 3 and Step 4 for the version of dmprSink.dat stored in this directory.
PAGE 275
CH A P T E R 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 This chapter describes how to migrate your Cisco PGW 2200 Softswitch to the Solaris 10 operating system and Cisco PGW 2200 Softswitch software Release 9.8.
PAGE 276
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Cautions and Notes • The disks in the system must be at least 18 GB in size. • You (or the person doing the upgrade) must be an experienced Solaris system administrator. You must be familiar with system administration tasks such as mounting file systems and running tar to save and restore files. Use Table 5-1 to determine the appropriate steps to upgrade your system.
PAGE 277
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Required Software Note The Cisco PGW 2200 Softswitch supports a live upgrade from the Sparc-based platforms to the Opteron-based platforms. There is no service outrage during the upgrade. For detailed procedure of this live upgrade, see the “Upgrading Lively from Sparc-based Platforms to Opteron-based Platforms” section on page 5-21.
PAGE 278
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Migration Overview Note • /etc/inet/hosts • /etc/inet/netmasks • /etc/inet/ntp.conf You may have already recorded some of this information based on the “Required Site-Specific Information” section on page 1-3 and the “Required Machine-Specific Information” section on page 1-3. Migration Overview In order to migrate to Release 9.
PAGE 279
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Migration from Release 9.5 or 9.6 to Release 9.8 without Platform Changes Table 5-2 Migration Procedures to Release 9.8 Across Different Platforms Target Release 9.8 From Release 9.5 or 9.6 From Release 9.7 Sparc-based Sparc-based Opteron-based Migration from Release 9.7 to Release 9.8 without Platform Changes, page 5-20 — Sparc-based Migration from Release 9.5 or 9.6 to Release 9.
PAGE 280
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Migration from Release 9.5 or 9.6 to Release 9.8 without Platform Changes % sudo /etc/init.d/CiscoMGC stop Step 4 Follow these steps to back up the system: a. Local Tape Backup—Using the mgcbackup utility, back up the system to the local tape drive. % /opt/CiscoMGC/local/mgcbackup –d /dev/rmt/0 b.
PAGE 281
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Migration from Release 9.5 or 9.6 to Release 9.8 without Platform Changes % /opt/TimesTen/32/bin/ttVersion presenter The Cisco PGW 2200 Softswitch displays output similar to the following example: [ output = "TimesTen Release x.y.z build time ... ] f. Replace the TimesTen database Release x.y.z with the new version: % echo xyz >/opt/CiscoMGC/etc/version.ttdb g. Ensure that the version.ttdb, migrate.ttdb, and export.
PAGE 282
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Migration from Release 9.5 or 9.6 to Release 9.8 without Platform Changes At this point, the Cisco PGW 2200 Softswitch configuration data has been saved in MGC.tar files on a tape or remote file server. The file backup is now complete. Proceed to “Installing Sun Solaris 10”. Installing Sun Solaris 10 Follow these steps to install Sun Solaris 10 on PGW host 2.
PAGE 283
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Migration from Release 9.5 or 9.6 to Release 9.8 without Platform Changes Caution Do not load Solstice DiskSuite (CSCOh023) if you are using Veritas Volume Manager to use the second disk for Solaris 8 fallback. For more information about Veritas Volume Manager, refer to http://www.sun.com/products-n-solutions/hardware/docs/Software/Storage_Software/VERITAS_Volu me_Manager/index.html.
PAGE 284
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Migration from Release 9.5 or 9.6 to Release 9.8 without Platform Changes Step 1 Install the Cisco PGW 2200 Softswitch software using the instructions in the “Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Releases” section on page 3-3. Step 2 When the installation is complete, perform the following steps on PGW host 2: Step 3 Log into PGW host 2 as mgcusr.
PAGE 285
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Migration from Release 9.5 or 9.6 to Release 9.8 without Platform Changes Note If you want to use two new disks drives to install the Cisco PGW 2200 Softswitch software Release 9.8, complete the “Installing Sun Solaris 10” and “Loading the Sun Solaris 10 Operating Environment Packages” sections before you begin this procedure.
PAGE 286
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Migration from Release 9.5 or 9.6 to Release 9.8 without Platform Changes % /opt/CiscoMGC/local/mgcbackup -l Caution Step 5 You must now move the backup file to a remote file server using the ftp program so it can be recovered if you need to revert the Cisco PGW 2200 Softswitch to the previous version of Solaris or Cisco PGW 2200 Softswitch software. You are responsible for providing the mechanism and storage location.
PAGE 287
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Migration from Release 9.5 or 9.6 to Release 9.8 without Platform Changes Step 11 Verify that configuration files were successfully backed up. The mgc____backup file and the MGC.tar file must be present. # cd /var/tmp/upgrade # ls Step 12 Caution At this point, you have saved all the required data in tar files in /var/tmp/upgrade.
PAGE 288
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Migration from Release 9.5 or 9.6 to Release 9.8 without Platform Changes Step 2 Wait for the system to return to the boot prompt then load the Cisco Solaris 10 Operating System Startup CD in the CD-ROM drive. If you are replacing the hard disks, power off the system, label, and remove the existing disks using proper anti-static procedures.
PAGE 289
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Migration from Release 9.5 or 9.6 to Release 9.8 without Platform Changes Step 4 Verify that the files successfully transfer to the remote file server before continuing. Step 5 Create an CiscoMGC directory and extract Cisco PGW 2200 Softswitch data files: # # # # # # # # cd /opt mkdir CiscoMGC # Create MGC directory cd /opt/CiscoMGC mkdir snmp # Create snmp directory cp /var/tmp/saved/MGC.tar MGC.tar tar xvf MGC.
PAGE 290
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Migration from Release 9.5 or 9.6 to Release 9.
PAGE 291
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Migration from Release 9.5 or 9.6 to Release 9.8 without Platform Changes 4. Remove Configuration Library Version Enter Selection or 'q' to quit> 3 e. The menu lists available configuration files. Configuration Versions 1. sip-upgrade-0131-3 2. sip-upgrade-0131 3. sip-upgrade-0131-2 4. sip-upgrade-0130 ***Current Production Version = sip-upgrade-0131-3 Enter Selection to Copy or 'q' to go back> f.
PAGE 292
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Migration from Release 9.5 or 9.6 to Release 9.8 without Platform Changes mml> rtrv-iplnk:all c.
PAGE 293
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Migration from Release 9.5 or 9.6 to Release 9.8 without Platform Changes migration completed successfully ***finish checking migration... This operation will copy the selected version of each configuration file from the LIBRARY to the PRODUCTION area. Do you want to overwrite the production files (y/n)? g. Enter y and press Enter to copy the files to the production area.
PAGE 294
Chapter 5 Migration from Release 9.7 to Release 9.8 without Platform Changes Note Step 13 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 If the call replication fails, or if new Active Host is not processing calls, refer to the Cisco PGW 2200 Softswitch Release 9 Operations, Maintenance, and Troubleshooting Guide. Restart PGW host 2 in order to ensure that the changes to the pom.dataSync variable take effect. Migration from Release 9.7 to Release 9.
PAGE 295
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Upgrading Lively from Sparc-based Platforms to Opteron-based Platforms Answer y to the question, “Is the uninstall being done in order to upgrade to a new version of the software?”, at the beginning of the uninstallation procedure. Note Step 10 Install the Cisco PGW 2200 Softswitch software Release 9.8 as described in the “Installing the Cisco PGW 2200 Softswitch Software Release 9.
PAGE 296
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Upgrading Lively from Sparc-based Platforms to Opteron-based Platforms Note No provisioning is allowed during the live upgrade. Before performing the live upgrade, you must stop all the MML provisioning sessions and quit from the MML interface on the old Sparc-based active and standby pair of Cisco PGW 2200 Softswitches.
PAGE 297
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Upgrading Lively from Sparc-based Platforms to Opteron-based Platforms Step 4 Use ftp utility to transfer MGC.tar, ttbackup.tar, and .odbc.ini which are generated in Step 2 and Step 3 from /var/tmp/upgrade directory to the remote file server. Note Use the binary mode of ftp to transfer the three files, MGC.tar, ttbackup.tar, and .odbc.ini.
PAGE 298
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Upgrading Lively from Sparc-based Platforms to Opteron-based Platforms Step 18 Use the following commands to move to the /opt/CiscoMGC/local directory and start the TimesTen database. # cd /opt/CiscoMGC/local # /etc/init.d/tt start Text similar to the following is displayed: The tt60 daemon has started successfully. Step 19 Change the login to mgcusr using the following command: # su - mgcusr Step 20 Run db_count.
PAGE 299
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Upgrading Lively from Sparc-based Platforms to Opteron-based Platforms CISCO.WHITELIST_A < 1001 > CISCO.WHITELIST_B < 1001 > Step 23 Log in PGW 2 as root and stop PGW 2 using the following command: # /etc/init.d/CiscoMGC stop Step 24 Remove PGW 2 from the current network environment and replace it with PGW 4. Step 25 Configure the required network parameters on PGW 4 to make PGW 4 a replacement of PGW 2.
PAGE 300
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Falling Back Overview Falling Back Overview Cisco PGW 2200 Softswitch supports both Sparc-based and Opteron-based platforms on Release 9.7(3) and 9.8(1). Prior to Release 9.7(3), only Sparc-based platforms are supported.
PAGE 301
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Falling Back to Solaris 8 and Cisco PGW 2200 Softswitch Release 9.5 or 9.6 Step 4 Restore the configuration using the following commands: % cd /opt/CiscoMGC/etc/CONFIG_LIB/ % tar xvf CFG_backup973.tar Step 5 Restore the snmp folder using the following command: % cd /opt/CiscoMGC % tar xvf SNMP_backup973.tar Step 6 Restore the dial plan configurations using the following commands: % tar xvf DP_backup973.
PAGE 302
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Falling Back to Solaris 8 and Cisco PGW 2200 Softswitch Release 9.5 or 9.6 Falling Back to Solaris 8 on the Second Disk Drive If the upgrade is not successful, you can fall back to Solaris 8: Step 1 Stop the operating system. # init 0 Step 2 From the ok prompt, boot the secondary boot disk.
PAGE 303
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Falling Back to Solaris 8 and Cisco PGW 2200 Softswitch Release 9.5 or 9.6 Step 6 Enter 4 to remove a disk for replacement. Remove a disk for replacement Menu: VolumeManager/Disk/RemoveForReplace Use this menu operation to remove a physical disk from a disk group, while retaining the disk name. This changes the state for the disk name to a "removed" disk.
PAGE 304
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Falling Back to Solaris 8 and Cisco PGW 2200 Softswitch Release 9.5 or 9.6 13 list Turn off the spare flag on a disk List disk information ? ?? q Display help about menu Display help about the menuing system Exit from menus Select an operation to perform: q Goodbye. Step 11 Use the vxdisk command to verify that rootdiska is removed. # vxdisk list Step 12 Shut down and boot from disk1.
PAGE 305
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Falling Back to Solaris 8 and Cisco PGW 2200 Softswitch Release 9.5 or 9.6 Output format: [Device_Name] c0t0d0 Step 18 To initialize the disk instead of encapsulating, enter y and press Enter. Note To encapsulate the disk, enter n and press Enter.
PAGE 306
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Falling Back to Previous Cisco PGW 2200 Softswitch Software Releases with Platform Changes Step 22 Use the vxprint command to make sure disk0 is remirrored to disk1. When this is complete, shut down the platform and boot. # vxprint –ht # init 0 ok boot Step 23 Repeat Step 3 to verify that the correct software is running.
PAGE 307
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Replacing Hard Disks on an Existing Solaris 10 Platform # /etc/init.d/CiscoMGC stop Step 4 Remove the platform from the current network environment and replace it with the old version Cisco PGW 2200 Softswitch. Step 5 Log in the old version Cisco PGW 2200 Softswitch as root. Step 6 Configure the required network parameters on PGW 4 to make PGW 4 a replacement of PGW 2.
PAGE 308
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Replacing Hard Disks on an Existing Solaris 10 Platform Backup Procedure Before restoring the mgcbackup file, you must install the same Cisco PGW 2200 Softswitch software release and the patch level that was originally on the platform. Follow these steps to back up the system: Step 1 Log in as root and enter the following command to stop the Cisco PGW 2200 Softswitch application: # /etc/init.
PAGE 309
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Replacing Hard Disks on an Existing Solaris 10 Platform Caution Be sure to follow the appropriate anti-static procedures when performing this procedure. Step 1 Label the hard disks with their current locations and remove them from the system. See the Sun System manual for your platform for the proper procedure. Step 2 Install the new hard disks in the same slots as the existing hard disks.
PAGE 310
Chapter 5 Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8 Replacing Hard Disks on an Existing Solaris 10 Platform The hard disk replacement on an existing platform running the Solaris 10 operating system and Cisco PGW 2200 Softswitch software Release 9.8 is now complete. Cisco PGW 2200 Softswitch Release 9.
PAGE 311
CH A P T E R 6 Configuring the Local Area Network Switch This chapter provides a brief overview of the local area network (LAN) switches (Cisco Catalyst Switch family) in your solution. The LAN switch connects the Cisco PGW 2200 Softswitch hosts to the media gateways (MGWs) or to the Cisco IP Transfer Point LinkExtender (ITP-L). A LAN switch is not provided with the Cisco PGW 2200 Softswitch.
PAGE 312
Chapter 6 Configuring the Local Area Network Switch Catalyst 2900 XL Series Catalyst 2900 XL Series See the following web sites for hardware and software documentation for the Catalyst 2900 XL series: http://www.cisco.com/warp/public/cc/pd/si/casi/ca2900xl/prodlit/index.shtml http://www.cisco.com/univercd/cc/td/doc/product/lan/c2900xl/index.
PAGE 313
A P P E N D I X A XECfgParm.dat File Parameters This appendix describes the parameters found in the XECfgParm.dat file for the Cisco PGW 2200 Softswitch software Release 9.x and how they are used by the media gateway controller (MGC). Understanding the XECfgParm.dat File Format The XECfgParm.dat file contains system-wide as well as system tuning parameters. All fields in this file are written in the parm = value format.
PAGE 314
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.
PAGE 315
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition *.actiononchargetableaccessfailure Allows you to specify the action to take when there is a failure to access the meter pulse tariff table. Default: 0 Valid values are: 0 (Continue Call) and 1 (Release Call). *.autonomous Enables a process, for example the engine, to be started without the system.
PAGE 316
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition *.ClearingLocation Specifies whether to override the default location field in the call context for any call, regardless of which network device released the call.
PAGE 317
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition *.CustSpecificINAPHandling Controls INAP (Intelligent Network Application Protocol) behavior, including advertised application context. Values: • tinap • finap • rinap • sinap Default: Null To enable network transfer and DTMF transfer services, set this parameter to sinap.
PAGE 318
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition *.DefaultLocation Specifies whether to override the default location field in the call context data for calls released by the Cisco PGW 2200 Softswitch.
PAGE 319
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition *.DisableCCBSoverTunneledQSIG Specifies the protocol used to deliver Call Back Services messages over the network. Valid Values: • 0—Callback Services are enabled using QSIG • 1—Callback Services are enabled using the QBE interface Default Value: 0 *.
PAGE 320
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition *.GWClearChannelAlgorithm Allows the use of the clear channel 64K unrestricted data transfer between gateways. Different gateways support different codecs. There is a command to see all the codecs supported on the gateway, including the clear channel codec.
PAGE 321
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition *.ipAddrLocalB Second local IP address; used for checkpointing and failover heartbeats if you have active/standby Cisco PGW 2200 Softswitch hosts. Note *.ipAddrPeerA If your configuration does not use an external card, leave this setting as the default value: 0.0.0.0.
PAGE 322
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition *.LISupport Enables Cisco PGW 2200 Softswitch to be used for Lawful Intercept. Set this parameter to true to enable Cisco PGW 2200 Softswitch support for Lawful Intercept. Note Default: false *.logDirectory Location of the active and rotated log files. Default: ..
PAGE 323
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition *.logPrio Defines the initial default logging level used by logging clients when sending messages to the logging server. Use the set-log MML command to change logging levels after installation. You can specify different logging levels for each process. For example, engine.
PAGE 324
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter *.logPrio (continued) Definition • Note *.LongCallTime Critical—These messages indicate errors so severe that a process cannot continue operating. Do not change this value unless you are debugging. Used to generate ongoing Call Data Block (CDB) 1060.
PAGE 325
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition *.maxLocationLabels Specifies the maximum number of location labels that can be provisioned. (Added in Release 9.6(1) Valid value: 3000 Note *.maxNumDChansPerPort Do not change this value. Specifies the maximum number of D-channels that can be provisioned per IP address or port.
PAGE 326
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition *.MMLManualBlockingCic Allows the Cisco PGW 2200 Softswitch to manually block channels that do not respond to Release, Restart, or Disconnect messages. This feature was introduced in Release 9.6(1). Values: • 0 = The MML_Manual_BLOCK capability is disabled.
PAGE 327
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition *.OwnClli Common language location identifier; used for circuit query validation when circuit queries are supported. Value: Alphanumeric string, up to 11 characters. Default: TTTT-SS-BB-XXX Example: 1111-22-33-444 *.
PAGE 328
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition *.RedirectingATree Used to control A-number screening/analysis via A-digit tree. This parameter allows the analysis system to use the A-Digit tree for mapping to the BLACKLIST function on the Redirecting CLI value.
PAGE 329
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition *.sipFailover Specifies whether the Cisco PGW 2200 Softswitch hosts, when connected with a session interrupt protocol (SIP) network, should perform an automatic switchover when a LAN interface fails. Default: false Valid values: true or false *.
PAGE 330
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition *.SUA.maxOPCs Defines the maximum number of SUA OPCs. Value: 64 Do not change this value. Note *.SUA.maxRoutesPerOpcApcSsn Defines the maximum number of SUA routes per OPC, adjacent point code (APC), and subsystem number (SSN) set. Value: 2 Do not change this value. Note *.SUA.
PAGE 331
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition *.tablesFile Location of the database directories. Default: ../etc/tables.dat Note *.tempDir Do not change this value. Location of the temporary files. Default: /tmp Note *.tibcoSupport Do not change this value. Determines whether or not the system supports a TIBCO maintenance interface.
PAGE 332
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition *.VSCNetworkPlacement Determines Cisco PGW 2200 Softswitch placement (AT or IXC) and bias routing accordingly. Values: • Nanp_AT • Nanp_IXC • NULL • 0 Default: NULL Note *.
PAGE 333
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition diskmonitor.CdrRmFinished Specifies the number of days to keep finished CDR files. The default value is 0, which means that if the Cisco BAMS is polling the Cisco PGW 2200 Softswitch, CDR.
PAGE 334
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition diskmonitor.DailyStartTime Specifies the time that the disk monitor is run each day to remove files that are older than the value set in diskmonitor.MaxKeepDays. The time is in 24-hour format and is based on the time set in the operating system. Default: 04:15 diskmonitor.
PAGE 335
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition diskmonitor.PreserveLogs Specifies, along with diskmonitor.SoftLimit, whether platform log data should be preserved or deleted once the disk usage percentage set in diskmonitor.Threshold is reached.
PAGE 336
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition diskmonitor.Threshold Erases old log files to free disk space. The threshold is the percent the disk is full before trimming starts. Only /var/log and /var/spool are monitored by default; the disk monitor function is local to these two directories by default.
PAGE 337
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition engine.CallLimitingControl Allows enabling or disabling the call limiting capability on the Cisco PGW 2200 Softswitch. (added in Release 9.6(1) Valid values: engine.CALL_MEM_BLOCK_SIZE • 0—Call limiting off (default) • 1—Call limiting on Block of memory allocated per call. Used by MDL.
PAGE 338
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition engine.
PAGE 339
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition engine.RelINAPCallsAfterSwOver Defines the treatment of INAP calls in answer state after platform switchover. This parameter is used for calls that require INAP interaction even after the answer state. Currently, this parameter is used only for Prepaid INAP calls.
PAGE 340
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition engine.ShortDurationCallPeriod Allows you to specify the period used to determine a short duration call. Calls with a duration less than the specified value are recorded as a short duration call in the CDR. Default: 0 Valid values are: 0–30. A setting of 0 indicates that this parameter is disabled.
PAGE 341
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition engine.SysGSMTimerInterval Allows group service messages (GSMs—used to advertise the state of circuits) to be sent at a periodic rate from the SS7 side of the network to the IP side of the network. Valid values: 1000–30000 Default for up to Release 9.2(2): 30000 Default for Release 9.
PAGE 342
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition engine.SysMdlMemoryReduction Controls use of MDL memory reductions. Prior to Release 9.4(1):values: • 0—MDL memory reductions not used (maximum performance) • 1—MDL memory reduction improvements used Default: 0 engine.
PAGE 343
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition engine.SysSGCPREtryTimerInterval The interval between SGCP message transmissions, in milliseconds. Default: 1000 Do not change this value. Note engine.SysTraceLevel A debugging tool that allows for different levels of engine tracing. Default: 3 Do not change this value. Note engine.
PAGE 344
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition foverd.abswitchPort Port used for communication with the A/B switch. Value: /dev/term/x Example: /dev/term/b If your configuration does not use an A/B switch, use the default value (/dev/null). Note foverd.
PAGE 345
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition foverd.conn3Addr Specifies the address of the peer system. Example: /dev/term/b If your configuration does not use connection number 3, enter /dev/null (default).
PAGE 346
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition foverd.ipLocalPortB Port number used for IP communication. Default: 0 Note foverd.ipPeerPortA If you have two Cisco PGW 2200 Softswitch hosts in a fault-tolerant configuration, enter this value for the foverd.ipPeerPortB field in the XECfgParm.dat file on the secondary host.
PAGE 347
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition GWNetworkContinuity For network continuity test on VISM. Valid values: 1—Network continuity is present/requested. 0—Network continuity is present/requested. Default: 0 (Currently this property only applies to VISM GWs.) This property should have value = 1 when the VISM GW property is switched on.
PAGE 348
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition ioChanMgr.sessionPauseTimer Amount of time the Cisco PGW 2200 Softswitch waits for a BSM session set to recover from failure before declaring the session set failure. Values: 1–10 seconds. Default: 8 ioChanMgr.
PAGE 349
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition logger.fileRotateInterval Triggers a file rotation based on the time elapsed since the previous rotation. Default: 1440 minutes (24 hours) Note logger.fileRotateSize This timer is reset after any rotation occurs, regardless of the cause or trigger of the rotation.
PAGE 350
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition MgcHeaderAddrType Sets the Cisco PGW 2200 Softswitch H.248 local MID address type. Values: • 1 = IP address • 2 = Domain name Default: 1 The localMID property contains related information. MML.chg-cfg Timeout value for the chg-cfg MML command in milliseconds; overrides MML.timeout.
PAGE 351
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition pom.dataSync Indicates that the Provisioning Object Manager (POM) should synchronize the provisioning data at startup. Values: • true—POM is enabled, data is synchronized. • false—POM is disabled, no data synchronization (default).
PAGE 352
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition procM.logDBFile Specifies the location of the log level storage. Default: ../var/procMLogTable procM.minCheckHealthInterval Seconds at which a process can generate heartbeats. Default: 10 seconds Note procM.minCheckHealthTimeout Do not change this value. Seconds at which a timeout can occur.
PAGE 353
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition RadiusAccounting.smSize The size of shared memory in MB. Value: Any integer from 1 to 199. Default: 30 replicator.portCommChannelRecv Communication port for the replicator. Default: 2974 Note replicator.portCommChannelSend Do not change this value. Communication port for the replicator.
PAGE 354
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition SIP.Conn_Idle_Period Defines the length of time (in seconds) that a TCP connection can remain idle before the Cisco PGW 2200 Softswitch closes the connection. A value of 0 means that the Cisco PGW 2200 Softswitch does not close idle TCP connections.
PAGE 355
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition SIP.naptr_record_locate Specifies the type of query the Cisco PGW 2200 Softswitch uses to determine the preferred transport protocol of a remote proxy. The Cisco PGW 2200 Softswitch uses the query result for outgoing SIP trunk groups with the siptransportmode property set to Dynamic.
PAGE 356
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition SIP.TransportProtocol Defines the transport protocol used to complete calls. The Cisco PGW 2200 Softswitch can only set up new calls using one protocol at a time. (Obsolete in Release 9.
PAGE 357
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition SipToIsupInterworkingInd Only applicable with SIP to ISUP (or ISUP to SIP) calls.
PAGE 358
Appendix A XECfgParm.dat File Parameters Understanding the XECfgParm.dat File Format Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters Configuration Parameter Definition TCAP.avgInvokePerDialog Sets the average number of Invokes for a TCAP dialog. A single dialog does not necessarily correspond to a single Invoke. The number of Invokes depends on the call flow for the TCAP dialog. Values: 1-10 Default: 1 TCAP.
PAGE 359
A P P E N D I X B Client/Server and Secure Connectivity Relationships This appendix describes the client/server and secure connectivity relationships used among the different applications of the Cisco PGW 2200 Softswitch, Cisco BAMS, and Cisco HSI. Client/Server and Secure Connectivity Relationships The following figures show the client/server and secure connectivity relationships used among the different applications of the Cisco PGW 2200 Softswitch, Cisco BAMS, and Cisco HSI.
PAGE 360
Appendix B Client/Server and Secure Connectivity Relationships Client/Server and Secure Connectivity Relationships Note For simplicity, redundant platforms are not shown in this figure. The secure connectivity among the different application types and the redundant platforms is the same.
PAGE 361
Appendix B Client/Server and Secure Connectivity Relationships Client/Server and Secure Connectivity Relationships Secure Connections between Cisco BAMS Platforms SFTP C Cisco BAMS S Cisco BAMS SFTP S C 205453 Figure B-3 Secure Connectivity Between Cisco BAMS and Cisco PGW 2200 Softswitch Application Platforms Figure B-4 illustrates the client/server relationship and the secure connectivity used when one redundant Cisco BAMS pair controls multiple Cisco PGW 2200 Softswitch application platforms.
PAGE 362
Appendix B Client/Server and Secure Connectivity Relationships Client/Server and Secure Connectivity Relationships Cisco PGW 2200 Softswitch Release 9.
PAGE 363
A P P E N D I X C HP OpenView Sample SNMP Configuration Configuring the Cisco PGW 2200 Softswitch to Send Alarms to HP OpenView This sample configuration sets up a Cisco PGW 2200 Softswitch to send alarms to HP OpenView. Step 1 Load the following MIBs in HP OpenView, in the order shown below. To load MIBs, select the Options menu, and choose Load/Unload MIBs: SNMP. MIB Location CISCO-SMI.my /opt/TransPath/snmp tp.my /opt/TransPath/snmp measurement.my /opt/TransPath/snmp v3-tgt.
PAGE 364
Appendix C HP OpenView Sample SNMP Configuration Configuring the Cisco PGW 2200 Softswitch to Send Alarms to HP OpenView Step 10 Click Set. You should see a dialog box indicating that the values are entered successfully. Step 11 Continue this process until all the MIB object IDs in the table below have the correct MIB instance and SNMP set values. Select MIB Object ID MIB Instance SNMP Set Value snmpTargetAddrRowStatus 51 5 snmpTargetAddrRowStatus 52 5 snmpTargetAddrTDomain 52 .1.3.6.1.6.1.
PAGE 365
Appendix C HP OpenView Sample SNMP Configuration Formatting Trap Messages Tip Select MIB Object ID MIB Instance SNMP Set Value snmpNotifyRowStatus 50 5 snmpNotifyTag 50 Manager1 snmpNotifyStorageType 50 3 snmpNotifyRowStatus 50 1 You can verify the settings by selecting each MIB OID and clicking Start Query. When you do this for snmpNotifyRowStatus, it should show four entries set to active. When you have verified the settings, you can close the MIB browser window. Step 14 Click Close.
PAGE 366
Appendix C HP OpenView Sample SNMP Configuration Formatting Trap Messages $5 tpAlarmSet Alarm set/not set. 2 means the alarm is being set. 1 means the alarm is being cleared $6 tpAlarmNotify Alarm notified/not notified $7 tpAlarmSeverity Alarm severity $8 tpAlarmReported Alarm reported $9 tpComponentId Component identification number. This number consists of two parts, the component type and component instance. The most significant 2 bytes signify the component type.
PAGE 367
A P P E N D I X D Sample Installation Scripts This appendix contains sample outputs from the following: • Sample Output from install.sh, page D-1 • Updated Configuration File Sample, page D-11 • Sample Configured snmpd.cnf File, page D-13 • Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.8(1), page D-16 • Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.7(3), page D-27 • Sample Configured XECfgParm.
PAGE 368
Appendix D Sample Installation Scripts Sample Output from install.sh Enter CiscoMGC UID [20000] Enter CiscoMGC group name [mgcgrp] Enter CiscoMGC GID [20000] [mgcgrp] group added [mgcusr] user added Modifying /etc/init.d/inetinit Installation of was successful. (c)1998 Cisco Systems, Inc. All Rights Reserved. Unpublished -- rights reserved under the copyright laws of the United States.
PAGE 369
Appendix D Sample Installation Scripts Sample Output from install.sh Installing libACE.so Installing libbtsUtil.so Installing libcmg.so Installing libconvutil.so Installing libcxn.so Installing libda.so Installing libeng.so Installing libengif.so Installing libhelp.so Installing libinf.so Installing libmmdb.so Installing libpem.so Installing libpolbase.so Installing libpolcomp.so Installing libpolfiles.so Installing libpolnuman.so Installing libpolroute.so Installing libpom.so Installing libpxe.
PAGE 370
Appendix D Sample Installation Scripts Sample Output from install.sh Preparing to install TimesTen in /opt on va-redskins Executing TimesTen installation script... NOTE: Each TimesTen installation is identified by a unique instance name. The instance name must be a non-null alphanumeric string, not longer than 255 characters. Instance name will be 'tt60'.
PAGE 371
Appendix D Sample Installation Scripts Sample Output from install.sh Installation of was successful. Updating parameters for critagt.cnf Updating parameters for startcia.sh Updating inittab Installation of was successful. Installing /opt/Toolkit/Packages/Packages.tar.gz Installing /opt/Toolkit/bytecode/XECfg/XECfg.tar.gz Installing /opt/Toolkit/bytecode/am/am.tar.gz Installing /opt/Toolkit/bytecode/cdr/cdr.tar.gz Installing /opt/Toolkit/bytecode/log/Viewer.tar.
PAGE 372
Appendix D Sample Installation Scripts Sample Output from install.
PAGE 373
Appendix D Sample Installation Scripts Sample Output from install.sh ## Q931_AUSTRALIA ## ## Q931_SINGAPORE ## ###################### Would you like to add a protocol set to your system? [y] [y,n,?,q] y SNMP Research Critical Application Subagent Version 16.2.0.35 @(#)Copyright 1992-2008 SNMP Research, Incorporated SNMP Research MIB2 Subagent Version 16.2.0.35 @(#)Copyright 1992-2008 SNMP Research, Incorporated SNMP Research Host Resources Subagent Version 16.2.0.
PAGE 374
Appendix D Sample Installation Scripts Sample Output from install.sh Uncompressing dummy.so Uncompressing lcm.mdo Uncompressing lcm.so Installation of was successful. Uncompressing BTNUP_BTNR167.mdo Uncompressing BTNUP_BTNR167.so Uncompressing BTNUP_IUP.mdo Uncompressing BTNUP_IUP.so Uncompressing DPNSS_BTNR188.mdo Uncompressing DPNSS_BTNR188.so Uncompressing QBE.mdo Uncompressing QBE.so Installation of was successful. Uncompressing IETF_SIP.mdo Uncompressing IETF_SIP.
PAGE 375
Appendix D Sample Installation Scripts Sample Output from install.sh Uncompressing Q761_AUSTRL.so Uncompressing Q761_AUSTRL_C2.mdo Uncompressing Q761_AUSTRL_C2.so Installation of was successful. Uncompressing Q761_BASE.mdo Uncompressing Q761_BASE.so Uncompressing Q761_BELG.mdo Uncompressing Q761_BELG.so Uncompressing Q761_BELG_97VER.mdo Uncompressing Q761_BELG_97VER.so Uncompressing Q761_CHILE.mdo Uncompressing Q761_CHILE.so Uncompressing Q761_CHINA.mdo Uncompressing Q761_CHINA.
PAGE 376
Appendix D Sample Installation Scripts Sample Output from install.sh Uncompressing Uncompressing Uncompressing Uncompressing Uncompressing Uncompressing Uncompressing ISUPV2_FINNISH96.so ISUPV2_FRENCH.mdo ISUPV2_FRENCH.so ISUPV2_GERMAN.mdo ISUPV2_GERMAN.so ISUPV2_ISRAEL.mdo ISUPV2_ISRAEL.so Installation of was successful. Uncompressing ISUPV2_JAPAN.mdo Uncompressing ISUPV2_JAPAN.so Uncompressing ISUPV2_JAPAN_C2.mdo Uncompressing ISUPV2_JAPAN_C2.so Uncompressing ISUPV2_NORWEGIAN.
PAGE 377
Appendix D Sample Installation Scripts Updated Configuration File Sample Uncompressing Uncompressing Uncompressing Uncompressing Uncompressing Uncompressing Uncompressing Uncompressing Uncompressing Uncompressing Uncompressing Uncompressing Uncompressing Uncompressing Uncompressing Q767_BASE.so Q767_BRAZIL.mdo Q767_BRAZIL.so Q767_BRAZIL_C2.mdo Q767_BRAZIL_C2.so Q767_COLOMBIA.mdo Q767_COLOMBIA.so Q767_GUATEMALA.mdo Q767_GUATEMALA.so Q767_INDONESIA.mdo Q767_INDONESIA.so Q767_ITAL.mdo Q767_ITAL.
PAGE 378
Appendix D Sample Installation Scripts Updated Configuration File Sample #---------------- MGC Environment Configuration Tool Usage -------------------# REQUIRED STARTUP PARAMETERS # DO NOT MOVE THESE PARAMETERS BEYOND THIS BOX *.platformId = 1 *.transpathId = 01 # Transpath Id for ASN *.ownTranspathId = 01 *.peerTranspathId = 02 *.MGC_CDR_NODE_ID = MGC-CDR-NODE-STRING # System Id for CDR *.desiredPlatformState = standalone *.virtualFaultTolerant = false # avoid prov-dply/sync on FT mode in egw ##### *.
PAGE 379
Appendix D Sample Installation Scripts Sample Configured snmpd.cnf File # Improved SIP Failover Support. Setting 0.0.0.0 to both will disable # the SIP Improved failover support Feature. Configuring only one will # cause the switchover, if the physical interface where it present fails. # *.Virtual_IP_Addr1 = 0.0.0.0 # Must be from *.IP_Addr1 Subnet. *.Virtual_IP_Addr2 = 0.0.0.0 # Must be from *.IP_Addr2 Subnet. ################################################################ *.
PAGE 380
Appendix D Sample Installation Scripts Sample Configured snmpd.
PAGE 381
Appendix D Sample Installation Scripts Sample Configured snmpd.
PAGE 382
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.8(1) # snmpTargetAddrTimeout (integer) # snmpTargetAddrRetryCount (integer) # snmpTargetAddrTagList (text) # snmpTargetAddrParams (text) # snmpTargetAddrStorageType (nonVolatile, permanent, readOnly) # snmpTargetAddrTMask (transport mask, i.e. 255.255.255.255:0) # snmpTargetAddrMMS (integer) snmpTargetAddrEntry 34 snmpUDPDomain 127.0.0.1:0 100 3 TrapSink \ v2cExampleParams nonVolatile 255.
PAGE 383
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.8(1) # Copyright (c) 1997-2008 by Cisco Systems, Inc.
PAGE 384
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.8(1) # are different on the two MGC hosts *.IP_NextHop1 = 0.0.0.0 *.IP_NextHop2 = 0.0.0.0 *.IP_NextHop3 = 0.0.0.0 *.IP_NextHop4 = 0.0.0.0 *.IP_NextHop5 = 0.0.0.0 *.IP_NextHop6 = 0.0.0.0 *.IP_NextHop7 = 0.0.0.0 *.IP_NextHop8 = 0.0.0.0 *.netmaskPeerB = 255.255.255.255 *.netmaskPeerA = 255.255.255.255 *.netmaskLocalB = 255.255.255.255 *.netmaskLocalA = 255.255.255.255 *.Peer_NextHop1 = 0.0.0.
PAGE 385
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.8(1) # DO NOT MOVE THESE PARAMETERS BEYOND THIS BOX #---------------- MGC Environment Configuration Tool Usage -------------------*.disableMeas =false *.sm_meas_baseaddr = 40960 # T ==> Don't accumulate meas in shared mem *.tempDir = /tmp # temporary directory *.dataDir = ../var # volatile data directory *.homeDirRoot = /opt/CiscoMGC *.logDirectory = ../var/log # NEW log directory *.
PAGE 386
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.8(1) *.PNPopulate = disable # disable/enable *.maxLocationLabels = 3000 # 0 to 3000 *.DisableCCBSoverTunneledQSIG = 0 # 0 = Enable, 1 = Disable *.analysisCapabilityLevel = 0 # 0 = existing analysis behaviour, 1 = Longest-matching capability enabled *.FaxUpspeedCodecPreference = null # attempt passthrough if T.38 fax fails *.
PAGE 387
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.8(1) # engine.logPrio = Debug # foverd.logPrio = Debug # M3UA.logPrio = Debug # measMgr.logPrio = Debug # MGCP.logPrio = Debug # H248.logPrio = Debug # mmdbd.logPrio = Debug # mmSAgt.logPrio = Debug # pom.logPrio = Debug # procM.logPrio = Debug # replicator.logPrio = Debug # sagt.logPrio = Debug # SIP.logPrio = Debug # SS7.logPrio = Debug # SUA.logPrio = Debug # TALI.logPrio = Debug # TCAP.
PAGE 388
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.8(1) engine.SysMaxOverlap = 28 engine.SysGSMTimerInterval = 10000 engine.LCMMdlFile = ../lib/lcm engine.CCMdlFile = ../lib/cc engine.mdoDir = ../lib/ engine.VersionTimeoutValue = 10000 engine.MDLANumberScreening = 0 # # # # # # GSM to be sent (milliseconds) LSI call model call context where .
PAGE 389
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.8(1) #---------------------cdrDmpr.openCDR = true cdrDmpr.seqFile = ../var/.cdr.
PAGE 390
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.8(1) SIP.connLocalMsgQueueSize = 1500 # Maximum number of local outgoing messsages per TCP connection queue SIP.udp2tcp_byte_xover = 0 # message size to control whether switch from UDP to TCP SIP.naptr_record_locate = 1 # whether to perform natpr dns query SIP.
PAGE 391
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.8(1) # connection 1 parameters foverd.conn1Type = socket # connection 2 parameters foverd.conn2Type = socket # connection 3 parameters foverd.conn3Type = foverd.conn3Addr = serial /dev/null foverd.heartbeatInterval = 1000 foverd.ackTimeout = 1000 foverd.abswitchTestInterval = 30000 foverd.graceShutTimeout = 6000 foverd.forceShutTimeout = 1000 foverd.commRetryInterval = 30000 foverd.
PAGE 392
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.8(1) engine.RelINAPCallsAfterSwOver = true #---------------------------------# Disk Monitor Parameters #---------------------------------diskmonitor.Limit = 7 # Minimum number of days to preserve (Trimming only occurs when threshold is exceeded. ) diskmonitor.Threshold = 80 # percentage full threshold diskmonitor.
PAGE 393
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.7(3) H248.localMID = 0.0.0.0 # MGC Message Identifier. IP address or domain name H248.MgcHeaderAddrType = 1 # MGC H.248 Message header type. 1=IP Address,2=Domain Name #-----------------------------------------------------------------------------# End of XE Configuration Parameter File #-----------------------------------------------------------------------------MML.
PAGE 394
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.7(3) #---------------- MGC Environment Configuration Tool Usage -------------------# REQUIRED STARTUP PARAMETERS # DO NOT MOVE THESE PARAMETERS BEYOND THIS BOX *.platformId = 1 *.transpathId = 01 # MIGRATED *.ownTranspathId = 01 # MIGRATED *.peerTranspathId = 02 # MIGRATED *.MGC_CDR_NODE_ID = MGC-CDR-NODE-STRING # MIGRATED *.desiredPlatformState = master # MIGRATED *.
PAGE 395
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.7(3) # Set *.sipFailover = true # MIGRATED # *.sipFailover = true # MIGRATED *.stPort = 0 # MIGRATED engine.SysVirtualSwitch = 1 # MIGRATED pom.dataSync = true # MIGRATED foverd.ipLocalPortA = 1051 # MIGRATED foverd.ipPeerPortA = 1052 # MIGRATED foverd.ipLocalPortB = 1053 # MIGRATED foverd.ipPeerPortB = 1054 # MIGRATED *.
PAGE 396
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.7(3) M3UA.maxOPCs = 64 # Max number of M3UA OPCs M3UA.maxRoutesPerOpcDpc = 2 # Max number of M3UA routes per OPC/DPC pair SUA.maxSgp = 8 # Max number of SUA SGPs SUA.maxSigServices = 256 # Max number of SUA signalling services SUA.maxOPCs = 64 # Max number of SUA OPCs SUA.maxRoutesPerOpcApcSSN = 2 # Max number of SUA routes per OPC/APC pair and remote SSN *.
PAGE 397
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.7(3) # # # # # # # # # unix filename of the process must be used. Only the logging level of actively or passively managed processes can be set. Valid values for logPrio are Debug, Trace, Info, Warning, Error, and Critical almM.logPrio = Debug amDmpr.logPrio = Debug cdrDmpr.logPrio = Debug cfgM.logPrio = Debug EISUP.logPrio = Debug # ioChanMgr.logPrio = Debug # ISDNIP.
PAGE 398
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.7(3) #------------# Engine #------------engine.SysPropagateChanAvail = false # MIGRATED engine.SysGeneratedCode = true engine.SysGRSTimerInterval = 0 # MIGRATED engine.SysGRSBlockSize = 0 # MIGRATED engine.SysSGCPRetryCount = 3 # max number of SGCP retry messages after failure engine.SysSGCPRetryTimerInterval = 1000 # interval between retransmission (msec) engine.SysCLIval = false engine.
PAGE 399
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.7(3) engine.ChargingMode = 1 # MIGRATED engine.ShortDurationCallPeriod = 0 # MIGRATED engine.ActionOnChargeTableAccessFailure = 0 # MIGRATED engine.CallLimitingControl = 0 # MIGRATED #---------------------# CDR dumper (cdrDmpr) #---------------------cdrDmpr.openCDR = true cdrDmpr.seqFile = ../var/.cdr.
PAGE 400
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.7(3) # measM #----------# # Currently we assume 8000 XEMeas objects fit into 8 Mb of shared memory. # measM.sm_seg_size = 32 # size of shared memory in MB (default is 32) measM.loadBalanceFactor = 20 # num of measmgr distribution points every 5 minutes measM.port = default # port to sync dynamic meas thresholds #---------# almM #---------# almM.
PAGE 401
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.7(3) foverd.conn3Type = foverd.conn3Addr = serial /dev/null foverd.heartbeatInterval = 1000 foverd.ackTimeout = 1000 foverd.abswitchTestInterval = 30000 foverd.graceShutTimeout = 6000 foverd.forceShutTimeout = 1000 foverd.commRetryInterval = 30000 foverd.statusRptInterval = 600000 foverd.peerCommTimeout = 3000 foverd.delayTimeout = 1000 foverd.transitionTimeout = 10000 foverd.
PAGE 402
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.7(3) diskmonitor.Limit = 7 # MIGRATED diskmonitor.Threshold = 80 # MIGRATED diskmonitor.SoftLimit = false # MIGRATED diskmonitor.CdrRmFinished = 0 # MIGRATED diskmonitor.OptFileSys = # list of optional filesystems to monitor (no trimming) diskmonitor.CoreRmDays = 1 # MIGRATED diskmonitor.CfgRmDirs = 64 # MIGRATED diskmonitor.logPrio = Info diskmonitor.
PAGE 403
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.6(1) # Default value: 0 Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.6(1) The following sample XECfgParm.dat files for Cisco PGW 2200 Softswitch Release 9.6(1) are located in the /opt/CiscoMGC/etc directory. # File: XECfgParm.dat # # Purpose: # # This file contains configuration parameters that may be accessed by # XE application programs at run-time.
PAGE 404
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.6(1) *.desiredPlatformState = *.virtualFaultTolerant = *.SysConnectDataAccess = Subsystem *.GWClearChannelAlgorithm = *.SipToIsupInterworkingInd = *.ipAddrLocalA = 10.0.1.160 *.ipAddrLocalB = 10.128.1.5 *.ipAddrPeerA = 10.0.1.161 *.ipAddrPeerB = 10.128.1.6 *.IP_Addr1 *.IP_Addr2 *.IP_Addr3 *.
PAGE 405
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.6(1) # DO NOT MOVE THESE PARAMETERS BEYOND THIS BOX #---------------- MGC Environment Configuration Tool Usage -------------------*.disableMeas = false *.sm_meas_baseaddr = 3400 # T ==> Don't accumulate meas in shared mem # shared memory based address *.tempDir = *.dataDir = *.homeDirRoot = *.logDirectory = *.logFileNamePrefix = *.logPrio = *.logMsgDrop = *.eventTrace = *.debugLevel = *.
PAGE 406
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.6(1) *.maxLocationLabels = 3000 # 0 to 3000 #-----------------------------------------------------------------------# Log Server logfile locations #-----------------------------------------------------------------------# daemonAddr is socket port for logger daemon logger.daemonAddr = ../var/lsd_addr # NEW logfile rotation size max in Megabytes logger.
PAGE 407
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.6(1) # Specialized "autonomous" flags for debug, fault isolation # engine.autonomous = true # cfgM.autonomous = true Talk2.autonomous = false #-------------# procM #-------------procM.minCheckHealthInterval = procM.minCheckHealthTimeout = procM.minKillGracePeriod = procM.almDwellInterval = procM.procHealthDfltAlmCat = procM.servicesDir = procM.servFmt = procM.recovDbFile = procM.
PAGE 408
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.6(1) *.SelectTermCustGrpId = 0 SigPath CustGrpId is 0000. # 1= Select Terminating SigPath CustGrpId if Originating # 0= Always select Originating SigPath CustGrpId *.GlareReattemptCauseValue = 44 # used for re-attempt by GW in Nailed configurations. *.
PAGE 409
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.6(1) # evtTimer(msec.) - Frequency at which the queue is scanned for Msgs. # hbTimer(msec.) - Heart-beat timer, Not yet implemented. # statDiscardThreshold - Size of Control Queue that triggers discarding # all the queued stat events. # sendThreshold - Max. Number of Events from the Queue sent at a time. # IPCsendThreshold - Max. Number of RSIPs from the Queue sent at a time. ioChanMgr.
PAGE 410
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.6(1) # (verb all lowercase) MML.chg-cfg = 10000 MML.startPM = /etc/init.d/CiscoMGC start MML.stopPM = /etc/init.d/CiscoMGC stop MML.vld-cic = 25000 MML.snd = 600000 MML.
PAGE 411
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.6(1) replicator.portDataChannelRecv replicator.portCommChannelSend replicator.portCommChannelRecv replicator.reconnectInterval = replicator.numberReadThreads = = 2970 = 2972 = 2974 15 1 # optional thread (0=no threads,1=one thread) #----------------# Audit properties #----------------engine.AuditTimerInterval = 1000 engine.
PAGE 412
Appendix D Sample Installation Scripts Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.6(1) MML.rtrv-callinfo = 30000 *.AllISDNLinksFailCausesFailover = false diskmonitor.PreserveCDRs = false pom.respTimeout = 1200000 *.AlarmOnActive = false bash-2.03$ Cisco PGW 2200 Softswitch Release 9.
PAGE 413
A P P E N D I X E Sample Uninstall Scripts This appendix contains sample outputs from the following section, Removing a Cisco PGW 2200 Softswitch Software Version: Sample Output for uninstall.sh, page E-1. Removing a Cisco PGW 2200 Softswitch Software Version: Sample Output for uninstall.sh You must stop running the Cisco PGW 2200 Softswitch software and quit all the MML sessions before you uninstall the Cisco PGW 2200 Softswitch software. The following is a sample output from the uninstall script.
PAGE 414
Appendix E Sample Uninstall Scripts Removing a Cisco PGW 2200 Softswitch Software Version: Sample Output for uninstall.sh Removing /opt/CiscoMGC/etc/migrate/migrate_7.0004_7.1 Removing /opt/CiscoMGC/etc/migrate/migrate_7.0005_7.1006 Removing /opt/CiscoMGC/etc/migrate/migrate_7.0_7.0001 Removing /opt/CiscoMGC/etc/migrate/migrate_7.1001_7.1002 Removing /opt/CiscoMGC/etc/migrate/migrate_7.1002_7.1003 Removing /opt/CiscoMGC/etc/migrate/migrate_7.1003_7.1004 Removing /opt/CiscoMGC/etc/migrate/migrate_7.
PAGE 415
Appendix E Sample Uninstall Scripts Removing a Cisco PGW 2200 Softswitch Software Version: Sample Output for uninstall.
PAGE 416
Appendix E Sample Uninstall Scripts Removing a Cisco PGW 2200 Softswitch Software Version: Sample Output for uninstall.
PAGE 417
Appendix E Sample Uninstall Scripts Removing a Cisco PGW 2200 Softswitch Software Version: Sample Output for uninstall.sh Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.6001_to_9.7001/ Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.6001_to_9.7001/properties.mod Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.7001_to_9.7002/ Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.7001_to_9.7002/properties.mod Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.7002_to_9.7003/ Removing /opt/CiscoMGC/etc/CONFIG_LIB/9.7002_to_9.7003/properties.
PAGE 418
Appendix E Sample Uninstall Scripts Removing a Cisco PGW 2200 Softswitch Software Version: Sample Output for uninstall.sh Saving rows... 0/0 rows saved. Table successfully saved. Saving table CISCO.CBBOOKINGINFO Saving index CISCO.CBBOOKINGINFO_IDX1 Saving rows... 0/0 rows saved. Table successfully saved. Saving table CISCO.CBMONITORINGINFO Saving index CISCO.CBMONITORINGINFO_IDX1 Saving rows... 0/0 rows saved. Table successfully saved. Saving table CISCO.CLIIPADDRESS Saving rows... 0/0 rows saved.
PAGE 419
Appendix E Sample Uninstall Scripts Removing a Cisco PGW 2200 Softswitch Software Version: Sample Output for uninstall.sh Table successfully saved. Saving table CISCO.NAMEDSQL Saving index CISCO.NAMEDSQLIX1 Saving rows... 150/150 rows saved. Table successfully saved. Saving table CISCO.NUMBERTERM Saving index CISCO.NUMBERTERM_IDX1 Saving rows... 0/0 rows saved. Table successfully saved. Saving table CISCO.PORTEDNUMBERS Saving index CISCO.PORTEDNUMBERS_TREE_IDX Saving rows... 0/0 rows saved.
PAGE 420
Appendix E Sample Uninstall Scripts Removing a Cisco PGW 2200 Softswitch Software Version: Sample Output for uninstall.sh Removal of was successful. Removal of was successful. Removal of was successful. Removal of was successful. Removal of was successful. Removal of was successful. Removal of was successful. Removal of was successful. Removal of was successful.
PAGE 421
A P P E N D I X F Sample LAN Configurations This appendix contains sample configurations for two LAN switches, Cisco Catalyst 5500 A and Cisco Catalyst 5500 B, and the route switch modules. Sample Configuration for Cisco Catalyst 5500 A To view the current configuration of the Cisco Catalyst 5500 A, type the following command in privileged mode, and press Enter: Catalyst_5513A (enable) show config Output similar to the following appears: begin ! #version 4.
PAGE 422
Appendix F Sample LAN Configurations Sample Configuration for Cisco Catalyst 5500 A set set set set set set ! #ip set snmp snmp snmp snmp snmp snmp trap enable trap enable trap enable extendedrmon extendedrmon extendedrmon config stpx syslog vlanmode disable vlanagent disable enable interface sc0 3 172.25.66.122 255.255.255.192 172.25.66.127 set interface sc0 up set interface sl0 0.0.0.0 0.0.0.
PAGE 423
Appendix F Sample LAN Configurations Sample Configuration for Cisco Catalyst 5500 A e bridge 0x0 stp ieee set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state active br idge 0x0 stp ibm set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state acti ve parent 0 ring 0x0 mode srb aremaxhop 7 stemaxhop 7 set interface sc0 3 172.25.66.122 255.255.255.192 172.25.66.
PAGE 424
Appendix F Sample LAN Configurations Sample Configuration for Cisco Catalyst 5500 A set logging level pruning 2 default set logging level snmp 2 default set logging level spantree 2 default set logging level sys 5 default set logging level tac 2 default set logging level tcp 2 default set logging level telnet 2 default set logging level tftp 2 default set logging level vtp 2 default set logging level vmps 2 default set logging level kernel 2 default set logging level filesys 2 default set logging level d
PAGE 425
Appendix F Sample LAN Configurations Sample Configuration for Cisco Catalyst 5500 A set port enable 1/1-2 set port level 1/1-2 normal set port speed 1/1-2 100 set port duplex 1/1-2 full set port trap 1/1-2 disable set port name 1/1-2 set port security 1/1-2 disable set port broadcast 1/1-2 100% set port membership 1/1-2 static set port protocol 1/1-2 ip on set port protocol 1/1-2 ipx auto set cdp enable 1/1-2 set cdp interval 1/1-2 60 set trunk 1/1 on isl 1-1005 set trunk 1/2 on isl 1-1005 set spantree po
PAGE 426
Appendix F Sample LAN Configurations Sample Configuration for Cisco Catalyst 5500 A set port protocol 3/1-24 ip on set port protocol 3/1-24 ipx auto set cdp enable 3/1-24 set cdp interval 3/1-24 60 set spantree portfast 3/1-24 enable set spantree portcost 3/1-24 3100 set spantree portpri 3/1-24 32 ! #module 4 : 12-port 10/100BaseTX Ethernet set module name 4 set module enable 4 set vlan 2 4/1-2 set vlan 3 4/7-8 set vlan 4 4/3-6 set port channel 4/1-4 off set port channel 4/5-8 off set port channel 4/9-12
PAGE 427
Appendix F Sample LAN Configurations Sample Configuration for Cisco Catalyst 5500 A set spantree portvlancost 4/8 cost 3018 set spantree portvlancost 4/9 cost 3099 set spantree portvlancost 4/10 cost 3099 set spantree portvlancost 4/11 cost 3018 set spantree portvlancost 4/12 cost 3018 ! #module 5 empty ! #module 6 empty ! #module 7 empty ! #module 8 empty ! #module 9 empty ! #module 10 empty ! #module 11 empty ! #module 12 : 1-port Route Switch set module name 12 set port level 12/1 normal set port trap
PAGE 428
Appendix F Sample LAN Configurations Sample Configuration for Cisco Catalyst 5500 B hostname Catalyst_5513A_RSM ! enable password cisco ! no ip domain-lookup ! ! ! interface Vlan2 ip address 209.165.200.224 255.255.255.224 no ip redirects standby 2 timers 1 3 standby 2 priority 110 standby 2 preempt standby 2 authentication VSC3000 standby 2 ip 172.25.66.60 ! interface Vlan3 ip address 209.165.200.224 255.255.255.
PAGE 429
Appendix F Sample LAN Configurations Sample Configuration for Cisco Catalyst 5500 B Catalyst_5513B (enable) show config Output similar to the following appears: begin ! #version 4.5(1) ! set password $1$7OtT$J/rAZe2CANYvHW72ZMtI10 set enablepass $1$0o8Z$xbxAzs4LlepsklB6Ju7VY.
PAGE 430
Appendix F Sample LAN Configurations Sample Configuration for Cisco Catalyst 5500 B ! #dns set ip dns disable ! #tacacs+ set tacacs attempts 3 set tacacs directedrequest disable set tacacs timeout 5 ! #authentication set authentication login tacacs disable console set authentication login tacacs disable telnet set authentication enable tacacs disable console set authentication enable tacacs disable telnet set authentication login local enable console set authentication login local enable telnet set authe
PAGE 431
Appendix F Sample LAN Configurations Sample Configuration for Cisco Catalyst 5500 B set spantree maxage 20 3 set spantree priority 2000 3 #vlan 4 set spantree fwddelay 4 4 set spantree hello 2 4 set spantree maxage 20 4 set spantree priority 2000 4 #vlan 1003 set spantree fwddelay 15 1003 set spantree hello 2 1003 set spantree maxage 20 1003 set spantree priority 32768 1003 set spantree portstate 1003 block 0 set spantree portcost 1003 62 set spantree portpri 1003 4 set spantree portfast 1003 disable #vla
PAGE 432
Appendix F Sample LAN Configurations Sample Configuration for Cisco Catalyst 5500 B clear timezone set summertime disable ! #set boot command set boot config-register 0x2 set boot system flash bootflash:cat5000-sup3.4-5-1.
PAGE 433
Appendix F Sample LAN Configurations Sample Configuration for Cisco Catalyst 5500 B set port duplex 2/1-2 full set port trap 2/1-2 disable set port name 2/1-2 set port security 2/1-2 disable set port broadcast 2/1-2 100% set port membership 2/1-2 static set port protocol 2/1-2 ip on set port protocol 2/1-2 ipx auto set cdp enable 2/1-2 set cdp interval 2/1-2 60 set trunk 2/1 desirable isl 1-1005 set trunk 2/2 desirable isl 1-1005 set spantree portfast 2/1-2 disable set spantree portcost 2/1-2 3019 set spa
PAGE 434
Appendix F Sample LAN Configurations Sample Configuration for Cisco Catalyst 5500 B set cdp interval 4/1-12 60 set trunk 4/1 auto isl 1-1005 set trunk 4/2 auto isl 1-1005 set trunk 4/3 auto isl 1-1005 set trunk 4/4 auto isl 1-1005 set trunk 4/5 auto isl 1-1005 set trunk 4/6 auto isl 1-1005 set trunk 4/7 auto isl 1-1005 set trunk 4/8 auto isl 1-1005 set trunk 4/9 auto isl 1-1005 set trunk 4/10 auto isl 1-1005 set trunk 4/11 desirable isl 1-1005 set trunk 4/12 desirable isl 1-1005 set spantree portfast 4/1
PAGE 435
Appendix F Sample LAN Configurations Sample Configuration for Cisco Catalyst 5500 B set spantree portcost 12/1 3005 set spantree portpri 12/1 15 set spantree portvlanpri 12/1 160 set spantree portvlancost 12/1 cost 3004 4-8,11-15 ! #module 13 empty ! #switch port analyzer !set span 1 1/1 both inpkts disable set span disable ! #cam set cam agingtime 1-4,1003,1005 300 end Sample Configuration for Cisco Catalyst 5500 B RSM To view the current configuration of the Cisco Catalyst 5500 B RSM, access the RSM in
PAGE 436
Appendix F Sample LAN Configurations Sample Configuration for Cisco Catalyst 5500 B standby 4 preempt standby 4 authentication VSC3000 standby 4 ip 209.165.200.224 ! router eigrp 1 network 209.165.200.