User's Manual

Appendix C
Regulatory Information
18
Australia
T
he
f
ollowing in
f
ormation applies i
f
y
ou use the product
wi
t
hin A
ust
r
a
li
a.
Sa
f
et
y
Notic
e
WARNING: To ensure comp
l
iance wit
h
exposure limits to radiofrequency fields, the
antenna of the device should be no closer than
20 cm
f
rom the bod
y
during use
.
New Ze
ala
n
d
T
he following information applies if you use the product
wit
h
in New Zea
l
an
d.
T
e
l
epermit Statemen
t
Th
e ca
bl
ing
b
etween t
h
e p
h
one port an
d
t
h
e p
h
one s
h
a
ll
not
e
x
ceed
1
00
m
et
r
es.
PTC200 General Warnin
g
T
he grant o
f
a Telepermit
f
or an
y
item o
f
terminal
equipment indicates only that Telecom has accepted
that the item complies with minimum conditions
f
or
co
nn
ect
i
o
n
to
i
ts
n
et
w
o
rk
.
I
t
in
d
i
cates
n
o
e
n
do
r
se
m
e
n
t
of the product by Telecom, nor does it provide any sort
o
f
warrant
y
. Above all, it provides no assurance that an
y
i
tem will work correctl
y
in all respects with another item
of Tele
p
ermitted e
q
ui
p
ment of a different make or model,
n
or does it impl
y
that an
y
product is compatible with all o
f
Te
l
eco
m’
s
n
et
w
o
rk
se
rvi
ces.
Wireless Connectivit
y
Securit
y
on Cisco-Links
y
s
ADSL2+ Dev
i
ce
s
S
etting up the securit
y
o
f
the wireless connection
a
ssociated with ADSL2+ device is the user’s responsibilit
y
.
T
elecom will take no responsibility for charges made to
u
ser’s accounts
d
ue to poor
ly
organize
d
wire
l
ess securit
y
a
llowin
g
unknown users to connect to the Internet via this
device. Do not com
p
lain to the Telecom Fault Service or
Jetstream He
l
p
d
es
k
s
h
ou
ld
t
h
is occur
.
G
eneral Warning for Cisco-Linksys ADSL2+
Devices an
d
ADSL2+ Capa
b
i
l
it
y
T
his device has been tested and found suitable to connect
to t
h
e Te
l
ecom ADSL2+ capa
b
i
l
it
y
. T
h
is in
d
icates on
ly
t
h
at
T
elecom has accepted that this device complies with the
spectrum management plan for ADSL2+ on copper cable
a
n
d
wit
h
simp
l
e voice
b
an
d
compati
b
i
l
it
y
tests inc
l
u
d
e
d
i
n PTC273. It does not indicate that this device is
f
ull
y
com
p
atible with all services accessed via the ADSL2+
capabilit
y
. Contact the supplier o
f
the device when
issues
occu
r
.
D
o
n
ot
ca
ll
t
h
e
T
e
l
eco
m F
au
l
t
Se
rvi
ce
o
r
t
h
e
Jetstream Hel
p
desk.
C
isco-Links
y
s ADSL2+ Devices on Long Line
s
A
DSL2+ devices ma
y
not achieve the t
y
pe o
f
“high speed
”
operation expected when attached to a line that is longer
t
h
an inten
d
e
d
by
t
h
e ITU-T Rec. G.996.1 ADSL stan
d
ar
d
i
.e. >3 km o
f
0.4mm cable or a shorter cable len
g
th with
several tails or multi
p
les. If the device is installed in such
con
d
itions an
d
d
oes not give t
h
e expecte
d
“
d
own
l
oa
d”
p
er
f
ormance, then do not re
f
er the matter to the Telecom
Fault Service or ADSL Hel
p
desk
.
United States of Americ
a
T
he
f
ollowing in
f
ormation applies i
f
y
ou use the product
within the United States of America
.
FCC St
a
tement
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance
20cm between the radiator and your body.
This equipment has been tested and found to comply with the 
limits for a Class B digital device, pursuant to part 15 of the 
FCC rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate 
radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference 
to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try 
to correct the interference by one or more of the following 
measures:

-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different 
from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for 
help.