Cisco 815 Integrated Services Router Hardware Installation Guide Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
CCSP, CCVP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.
CONTENTS Preface ix Audience and Scope ix Organization ix Related Documentation x Conventions xi Notes, Cautions, and Warnings xi Commands xviii Accessibility xix Obtaining Documentation xix Cisco.
Contents Product Serial Number Location 1-3 Back Panel Ports and LEDs 1-4 Front Panel LEDs 1-6 Router Memory 1-8 Types of Memory 1-8 Amounts of Memory 1-9 Unpacking the Router 1-10 CHAPTER 2 Installation 2-1 Before Installing the Router 2-1 Connecting the Router to Your Local Network 2-2 Connecting Power to the Router 2-5 Verifying Your Installation 2-6 Optional Installation Procedures 2-7 Connecting a PC 2-7 Connecting a Modem 2-9 Stacking the Router 2-10 Unstacking the Router 2-13 CHAPTER 3 Trouble
Contents Troubleshooting WICs and Cables 3-8 Example 3-9 Troubleshooting the Power System 3-11 APPENDIX A Technical Specifications A-1 APPENDIX B Cabling Specifications B-1 Ethernet Cables B-1 Ethernet Network Cabling Guidelines B-2 Console Cable and Adapter B-3 APPENDIX C Installing and Upgrading Memory and Virtual Private Network Modules C-1 Safety Warnings C-1 Opening the Chassis C-2 Locating Modules C-4 Installing and Removing a DIMM C-4 Removing a DIMM C-5 Installing a DIMM C-6 Installing a V
Contents Cisco 815 Integrated Services Router Hardware Installation Guide viii OL-9558-01
Preface This section describes the intended audience, scope, and organization of the Cisco 815 Integrated Services Router Hardware Installation Guide and defines the conventions used to convey instructions and information. Audience and Scope This guide is for users who have some experience in installing and maintaining networking hardware. Cisco 815 integrated services router users should be familiar with the terminology and concepts of local Ethernet and wide-area networking.
Preface Related Documentation • Chapter 3, “Troubleshooting,” describes some problems that you might experience with the router and how to solve these problems. • Appendix A, “Technical Specifications,” lists the physical characteristics, environmental requirements, and power specifications for the router. • Appendix B, “Cabling Specifications,” provides the cables and cabling guidelines for the router.
Preface Conventions Conventions This guide uses the following conventions for information and instructions. Notes, Cautions, and Warnings Notes, cautions, and warnings use the following conventions and symbols: Note Caution Means reader take note. Notes contain helpful suggestions or references to materials not contained in this manual. This caution symbol means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.
Preface Conventions Varoitus Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista. Tässä julkaisussa esiintyvien varoitusten käännökset löydät laitteen mukana olevasta Regulatory Compliance and Safety Information -kirjasesta (määräysten noudattaminen ja tietoa turvallisuudesta).
Preface Conventions Advarsel Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan føre til personskade. Før du utfører arbeid på utstyr, må du vare oppmerksom på de faremomentene som elektriske kretser innebærer, samt gjøre deg kjent med vanlig praksis når det gjelder å unngå ulykker.
Preface Conventions Cisco 815 Integrated Services Router Hardware Installation Guide xiv OL-9558-01
Preface Conventions Cisco 815 Integrated Services Router Hardware Installation Guide OL-9558-01 xv
Preface Conventions Cisco 815 Integrated Services Router Hardware Installation Guide xvi OL-9558-01
Preface Conventions Cisco 815 Integrated Services Router Hardware Installation Guide OL-9558-01 xvii
Preface Conventions Commands Table 1 describes the syntax used with the commands in this document. Table 1 Command Syntax Guide Convention Description boldface Commands and keywords. italic Command input that is supplied by you. [ Keywords or arguments that appear within square brackets are optional. ] {x | x | x} A choice of keywords (represented by x) appears in braces separated by vertical bars. You must select one. ^ or Ctrl Represent the key labeled Control.
Preface Accessibility Table 1 Command Syntax Guide (continued) Convention Description boldface screen font Examples of information that you must enter. < > Nonprinting characters, such as passwords, appear in angled brackets. [ ] Default responses to system prompts appear in square brackets. Accessibility This product family uses a command line interface (CLI). The CLI is 508 conformant since it is text based and relies on a keyboard for navigation.
Preface Obtaining Documentation You can access international Cisco websites at this URL: http://www.cisco.com/public/countries_languages.shtml Product Documentation DVD The Product Documentation DVD is a comprehensive library of technical product documentation on a portable medium. The DVD enables you to access multiple versions of installation, configuration, and command guides for Cisco hardware and software products.
Preface Documentation Feedback Documentation Feedback You can rate and provide feedback about Cisco technical documents by completing the online feedback form that appears with the technical documents on Cisco.com. You can submit comments about Cisco documentation by using the response card (if present) behind the front cover of your document or by writing to the following address: Cisco Systems Attn: Customer Document Ordering 170 West Tasman Drive San Jose, CA 95134-9883 We appreciate your comments.
Preface Cisco Product Security Overview Reporting Security Problems in Cisco Products Cisco is committed to delivering secure products. We test our products internally before we release them, and we strive to correct all vulnerabilities quickly. If you think that you have identified a vulnerability in a Cisco product, contact PSIRT: • For Emergencies only — security-alert@cisco.
Preface Obtaining Technical Assistance Obtaining Technical Assistance Cisco Technical Support provides 24-hour-a-day award-winning technical assistance. The Cisco Technical Support & Documentation website on Cisco.com features extensive online support resources. In addition, if you have a valid Cisco service contract, Cisco Technical Assistance Center (TAC) engineers provide telephone support. If you do not have a valid Cisco service contract, contact your reseller.
Preface Obtaining Technical Assistance Submitting a Service Request Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service requests are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Service Request Tool provides recommended solutions. If your issue is not resolved using the recommended resources, your service request is assigned to a Cisco engineer.
Preface Obtaining Additional Publications and Information Severity 3 (S3)—Operational performance of the network is impaired, while most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels. Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations.
Preface Obtaining Additional Publications and Information • iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies learn how they can use technology to increase revenue, streamline their business, and expand services. The publication identifies the challenges facing these companies and the technologies to help solve them, using real-world case studies and business strategies to help readers make sound technology investment decisions.
C H A P T E R 1 Overview This chapter introduces the Cisco 815 integrated services router, also referred to in this guide as the router, and covers the following topics: • Key Features • Back Panel Ports and LEDs • Front Panel LEDs • Router Memory • Unpacking the Router Key Features The Cisco 815 integrated services router (see Figure 1-1) is a small, modular desktop router that provides an integrated cable solution.
Chapter 1 Overview Key Features Cisco 815 Integrated Services Router 146794 Figure 1-1 PWR WIC0 ACT/C WI H0 AC C1 T/CH0 Cisco 80 ETH ACT OK ACT/C H1 AC T/C seri0 es r o u te r H1 COL Table 1-1 Key Features Feature Description One Fast Ethernet (10/100BASE-TX) port Two Cisco WAN interface card (WIC) slots • Operates in full- or half-duplex mode (with manual override available). • Supports autosensing for 10- or 100-Mbps operation. • Supports IEEE 802.1Q VLAN encapsulation.
Chapter 1 Overview Key Features Table 1-1 Key Features (continued) Feature Description AutoInstall support Configuration files can be easily downloaded to the router over a WAN connection. Kensington security slot Router can be secured to a desktop or other surface using Kensington lockdown equipment.
Chapter 1 Overview Back Panel Ports and LEDs Back Panel Ports and LEDs This section describes the router back panel ports and LEDs, which are shown and identified in Figure 1-3 and are described in Table 1-2 and Table 1-3. Figure 1-4 shows a closer view of the WIC-4ESW module, which is installed in the WIC 0 slot on the router. Figure 1-5 shows a closer view of the HWIC-CABLE-D-2 module, which is installed in the WIC 1 slot on the router.
Chapter 1 Overview Back Panel Ports and LEDs Figure 1-4 WIC-4ESW ACT 4x LNK AC T 3x LN K ACT 2x LNK ACT 1x LNK Figure 1-5 DS ABLE-D Table 1-2 HWIC-CABLE-D-2 -2 CABLE US ONLINE LINK 146788 HWIC-C 95777 WIC 4ESW POWER Back Panel Connectors Connector/Slot Label/Color Description Ethernet port 10/100 ETHERNET (yellow) Connects the router to the local Ethernet network.
Chapter 1 Overview Front Panel LEDs Use the back panel LEDs during router installation to confirm that you have correctly connected all the cables to the router. Table 1-3 Back Panel LEDs LED Label Color Description WIC0 OK Green On when the WIC is correctly installed in the card slot. There are 2 LEDS associated with the WIC-4ESW: The right LED, which is labeled LNK, and the left LED, which is labeled ACT.
Chapter 1 Overview Front Panel LEDs Front Panel LEDs WIC0 WIC1 ETH PWR ACT/CH0 ACT/CH0 ACT OK ACT/CH1 ACT/CH1 COL 65537 Figure 1-6 Table 1-4 Front Panel LEDs LED Label Color Description PWR Green On means that DC power is being supplied to the router. OK Green On means that the router has successfully booted up and the software is functional. This LED blinks during the power-on self-test (POST).
Chapter 1 Overview Router Memory Table 1-4 Front Panel LEDs (continued) LED Label Color Description 2-port serial cards—Blinks when data is being sent to or received from the second port on the 2-port card in the WIC 1 slot. ETH N/A N/A. ACT Green Blinks when there is network activity on the Ethernet port. COL Yellow Blinks when there are packet collisions on the local Ethernet network.
Chapter 1 Overview Router Memory Amounts of Memory The Cisco 815 integrated services router supports a maximum of 32 MB of flash memory and 128 MB of DRAM. Use the show version command to see how much DRAM, NVRAM, and flash memory is stored in your router. The following example of output for the show version command shows the amount of memory in this router: 815# show version Cisco IOS Software, C815 Software (C815-IPBASE-M), Version 12.4(5.13.
Chapter 1 Overview Unpacking the Router Unpacking the Router Figure 1-7 lists the items that come with your router. All these items are in the accessory kit that came with your router.
C H A P T E R 2 Installation This chapter provides procedures for installing the Cisco 815 integrated services router and includes the following sections: • Before Installing the Router • Connecting the Router to Your Local Network • Connecting Power to the Router • Verifying Your Installation • Optional Installation Procedures Before Installing the Router The Cisco 815 integrated services router is shipped ready for desktop mounting.
Chapter 2 Installation Connecting the Router to Your Local Network Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals.
Chapter 2 Installation Connecting the Router to Your Local Network Caution Do not connect a WAN cable to the card until you have completed the installation procedure. Note For details about specific WAN interface cards (WICs), connecting the card to the WAN line, and configuring the interface with Cisco IOS software, see the Cisco Interface Cards Hardware Installation Guide. Warning The ports labeled 10/100 ETHERNET and CONSOLE are safety extra-low voltage (SELV) circuits.
Chapter 2 Installation Connecting the Router to Your Local Network Figure 2-1 Cisco Connecting the Router to the Local Network WIC 4ESW 815 ACT 4x LNK WIC0O K ACT 3x LNK ACT 2x LNK ACT FDX CONS OLE 1x LNK 100 LINK 10/10 0 ET HERN HWIC-C ABLE-D -2 DS US ONLINE CABLE ET AUX MODO K WIC LINK POW ER 1O K +5, +1 2, -12 VD C 1 3 2 AUI 155186 8 7 6 5 4 3 2 1 Step 2 1 10/100 Ethernet port on the Cisco 815 integrated services router 2 Straight-through Ethernet cable 3 Ethern
Chapter 2 Installation Connecting Power to the Router Connecting Power to the Router Read the following warnings before connecting the router to power. Warning The power supply is designed to work with TN power systems. Warning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use.
Chapter 2 Installation Verifying Your Installation 1 2 Power supply Power socket Step 2 Connect one end of the separate power cord to the socket on the power supply. Step 3 Connect the other end of the separate power cord to a power outlet. Step 4 Press the router power switch to ON ( | ). Step 5 Confirm that the router has power by checking that the PWR LED on the front panel is on.
Chapter 2 Installation Optional Installation Procedures Optional Installation Procedures This section describes some installation procedures that you might or might not use, depending on your site and on how you are configuring the router.
Chapter 2 Installation Optional Installation Procedures Figure 2-3 Connecting the Console Cable to the Router 4 815 ACT 4x LN K ACT 3x LNK ACT 2x LN K WIC0O ACT 1x LN K CONS OLE K FDX 100 LINK 10/100 ETHE HWICCABL E-D-2 RNET AUX DS CABL US ONLIN E E MOD OK W LINK POWE R IC 1O K +5, +1 2, -1 2 VD C 2 1 3 146793 WIC 4ESW Cisco 1 Blue console cable 3 To PC or terminal 2 Console port 4 Cisco 815 integrated services router Step 2 Connect the DB-9 end of the conso
Chapter 2 Installation Optional Installation Procedures Connecting a Modem When a modem is connected to the auxiliary port, a remote user can dial in to the router and configure it. You can use the console cable provided in the accessory kit. Follow these steps to connect a modem to the router, using the console cable: Step 1 Connect the RJ-45 end of the cable to the black AUX port on the back of the router, as shown in Figure 2-4.
Chapter 2 Installation Optional Installation Procedures Step 2 Connect the DB-9 end of the cable to the DB-9 end of the DB-9-to-DB-25 adapter. Step 3 Connect the DB-25 end of the adapter to the modem. Stacking the Router You can stack one Cisco 815 integrated services router in a four-device stack, along with other Cisco products designed for stacking with the router. Using a stacking clip and fastener, you can stack each device directly on top of another device.
Chapter 2 Installation Optional Installation Procedures Figure 2-5 Assembling Stacking Clip and Fastener H11542 Push plastic fastener through small hole at the end of the stacking clip. After assembling the clip and fastener, follow these steps to stack the router with another device: Step 1 Place the clip on top of the lower device, as shown in Figure 2-6. Slide the clip forward so that the front tabs slide into the vent slots. Make sure that the back hooks fit over the edge of the lower device.
Chapter 2 Installation Optional Installation Procedures Figure 2-6 Stacking the Router (Back View) 1 WIC 4ESW Cisco 815 ACT WIC0O 4x LNK ACT 3x LNK K ACT 2x LNK ACT FDX CONS 1x LNK 100 OLE LINK 10/100 HWIC-CA ETHE BLE-D-2 RNET DS CABLE AUX US ONLINE MODO K WIC LINK POW ER 1O K +5, +1 2, -12 VD C 5 155189 2 WIC 4ESW Cisco 815 ACT WIC0O K 4x LNK ACT 3x LNK ACT 2x LNK ACT FDX CONS 1x LNK 100 OLE LINK 10/100 3 HWIC-CA BLE-D-2 ETHE RNET 4 DS CABLE AU
Chapter 2 Installation Optional Installation Procedures Unstacking the Router Follow these steps to unstack the router from another device: Press up on the tab over the center of the lower device to release the clip from the vent, as shown in Figure 2-7.
Chapter 2 Installation Optional Installation Procedures Cisco 815 Integrated Services Router Hardware Installation Guide 2-14 OL-9558-01
C H A P T E R 3 Troubleshooting Use the information in this chapter to help isolate problems you might encounter with the Cisco 815 integrated services router or to rule out the router as the source of the problem. This appendix contains the following sections: • Contacting Your Cisco Reseller • Recovering a Lost Password • Problem Solving Contacting Your Cisco Reseller If you cannot locate the source of a problem, contact your local reseller for advice.
Chapter 3 Troubleshooting Recovering a Lost Password Recovering a Lost Password This section describes how to recover a lost enable password and how to enter a new enable secret password. Password recovery consists of the following major processes: • Determining the Configuration Register Value With this process, you determine the configuration of the router, so that you may restore the configuration after the password is recovered.
Chapter 3 Troubleshooting Recovering a Lost Password Step 4 At the user EXEC prompt (Router>), enter the show version command to display the existing configuration register value (shown at the end of this example output): 815# show version Cisco IOS Software, C815 Software (C815-IPBASE-M), Version 12.4(5.13.5)PIA5 ENGINEERING WEEKLY BUILD, synced to haw_t_pi4_abu HAW_T_PI4_ABU_5_13_1_PIA4 Copyright (c) 1986-2006 by Cisco Systems, Inc.
Chapter 3 Troubleshooting Recovering a Lost Password Resetting the Router Follow these steps to reset the router: Step 1 Do one of the following: • If break is enabled, go to Step 2. • If break is disabled, turn off the router, wait 5 seconds, and turn it on again. Within 60 seconds, press the Break key. The terminal displays the ROM monitor prompt. Go to Step 3. Note Step 2 Some terminal keyboards have a key labeled Break.
Chapter 3 Troubleshooting Recovering a Lost Password Step 7 Enter the enable command to enter privileged EXEC mode. Configuration changes can be made only in this mode. Router> enable The prompt changes to the privileged EXEC prompt: Router# Step 8 Enter the show startup-config command to display an enable password in the configuration file: Router# show startup-config If you are using an enable password, it will appear in the startup configuration. Write down the password and keep the record secure.
Chapter 3 Troubleshooting Recovering a Lost Password Resetting the Password Follow these steps to reset an enable secret password and restore the configuration of the router: Step 1 Enter the configure terminal command to enter configuration mode: Router# configure terminal Step 2 Enter the enable secret command to reset the enable secret password in the router: Router(config)# enable secret Step 3 Enter the config-register command and the original configuration register value that you re
Chapter 3 Troubleshooting Problem Solving Step 3 Press Ctrl-Z to exit configuration mode: Router(config)# Ctrl-Z Step 4 Reboot the router, and enter the recovered enable password. Problem Solving The key to problem solving is to isolate the problem to a specific subsystem by comparing what the router is doing to what it should be doing.
Chapter 3 Troubleshooting Problem Solving Table 3-1 OK LED Blinking Patterns Number of Blinks Meaning 2 The 860P dual-port random-access memory (DPRAM) has failed. 3 The parameter RAM area of the 860P DPRAM has failed. 4 The 860P system protection control register has a write failure. 5 The router cannot detect the dynamic random-access memory (DRAM). 6 The user programmable machine has a write failure. 9 The router DRAM has failed.
Chapter 3 Troubleshooting Problem Solving Table 3-2 Troubleshooting WICs (continued) Symptom Possible Cause(s) Router boots, but the console screen is frozen. • Make sure that the console cable is securely connected to the router and to the PC or terminal. • Verify that the parameters for your terminal are set to the following: – 9600 baud – 8 data bits – No parity generated or checked – 1 stop bit Router powers on and boots only when a particular WIC is removed from the router.
Chapter 3 Troubleshooting FF FF FF FF FF FF FF FF FF FF Problem Solving 0x30: 0x40: 0x50: 0x60: 0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF WIC/VIC Slot 0: 4 Port FE Switch Daughter card-Version 4 TLV Cookie Format Hardware Revision : 1.
Chapter 3 Troubleshooting Problem Solving EEPROM format version 4 EEPROM contents (hex): 0x00: 04 FF CF 06 00 D0 0x10: 4F 43 30 36 30 34 0x20: 82 4A 0F 16 02 42 0x30: FF FF FF FF FF FF 0x40: FF FF FF FF FF FF 0x50: FF FF FF FF FF FF 0x60: FF FF FF FF FF FF 0x70: FF FF FF FF FF FF 0x80: FF FF FF FF FF FF 0x90: FF FF FF FF FF FF 0xA0: FF FF FF FF FF FF 0xB0: FF FF FF FF FF FF 0xC0: FF FF FF FF FF FF 0xD0: FF FF FF FF FF FF 0xE0: FF FF FF FF FF FF 0xF0: FF FF FF FF FF FF 2B 30 30 FF FF FF FF FF FF FF FF FF
Chapter 3 Troubleshooting Problem Solving Table 3-3 Troubleshooting the Power System (continued) Symptom Possible Cause(s) The router is on, but the front panel PWR LED is off. The power supply has failed. The front panel PWR LED is on, the The power supply has failed. front panel OK LED is off, and the router does not pass console or EIA data.
A P P E N D I X A Technical Specifications Table A-1 lists hardware and operating specifications for the Cisco 815 integrated services router. Table A-1 Cisco 815 Integrated Services Router Specifications Description Specification Console port RJ-45 Auxiliary port RJ-45 Ethernet port RJ-45 Dimensions— HxWxD 3.1 x 11.2 x 8.7 in. (7.85 x 28.4 x 22.1 cm) Weight 2.6 lb (1.18 kg) With two WICs 2.9 lb (1.
Appendix A Table A-1 Technical Specifications Cisco 815 Integrated Services Router Specifications (continued) Description Specification Operating Specifications Operating temperature 32° to 104°F (0° to 40°C) Storage temperature –40° to 149°F (–40° to 65°C) Operating humidity 10% to 85%, noncondensing Cisco 815 Integrated Services Router Hardware Installation Guide A-2 OL-9558-01
A P P E N D I X B Cabling Specifications This appendix describes cables and cabling guidelines for the Cisco 815 integrated services router and contains the following sections: Note • Ethernet Cables • Ethernet Network Cabling Guidelines • Console Cable and Adapter For information about cables used with Cisco WAN interface cards (WICs), refer to the Cisco Interface Cards Hardware Installation Guide.
Appendix B Cabling Specifications Ethernet Network Cabling Guidelines Table B-1 Ethernet Cable Pinouts RJ-45 Pin1 Signal Direction RJ-45 Pin 1 TX+ —> 1 2 TX– —> 2 3 RX+ <— 3 6 RX– <— 6 1. Pins 4, 5, 7, and 8 are not used for signaling. Ethernet Network Cabling Guidelines Table B-2 describes some guidelines for creating Ethernet networks. Figures might vary, depending on the manufacturer of the network equipment.
Appendix B Cabling Specifications Console Cable and Adapter Console Cable and Adapter A console cable is provided with your router. Use this cable to connect the router to a PC or terminal. The router comes with a DB-9-to-DB-25 adapter that may be used for connecting the router to a modem, using the console cable. Table B-3 describes the wiring for the console port and the console cable. This table also includes pinouts for the DB-9-to-DB-25 adapter.
Appendix B Cabling Specifications Console Cable and Adapter Cisco 815 Integrated Services Router Hardware Installation Guide B-4 OL-9558-01
A P P E N D I X C Installing and Upgrading Memory and Virtual Private Network Modules This chapter tells how to install or upgrade memory and how to install a Virtual Private Network (VPN) module in your Cisco 815 integrated services router and includes the following sections: • Safety Warnings • Opening the Chassis • Locating Modules • Installing and Removing a DIMM • Installing a VPN Module • Closing the Chassis Safety Warnings Warning During this procedure, wear grounding wrist straps to a
Appendix C Installing and Upgrading Memory and Virtual Private Network Modules Opening the Chassis Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. Warning Read the installation instructions before you connect the system to its power source. Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches).
Appendix C Installing and Upgrading Memory and Virtual Private Network Modules Opening the Chassis Figure C-1 Removing the Chassis Screws #1 Phillips screwdriver DC 2V , -1 12 ,+ +5 MO CA BL E 155191 10 F W 5 sco Ci 81 IC 0O K AC T 4x LN K AC T 3x LN K AC T 2x 10 DX LN K AC T 1x 0 LN LIN /10 ER NE DO K W DS ON US LIN E IC 1O K LIN K PO WER HW IC-C AB LE -D -2 AU X 0E TH T K CO NS OL E K WIC 4ESW Step 4 Holding the router assembly together, turn
Appendix C Installing and Upgrading Memory and Virtual Private Network Modules Locating Modules Locating Modules Figure C-2 shows where to find the slots for a dual in-line memory module (DIMM) and a VPN module on the router motherboard.
Appendix C Installing and Upgrading Memory and Virtual Private Network Modules Installing and Removing a DIMM DIMMs have a polarization notch on the mating edge to prevent incorrect insertion. Figure C-3 shows the polarization notch on a DRAM DIMM. DIMM Polarization Notch 155842 Figure C-3 Polarization notch Removing a DIMM Follow these steps to remove a DIMM on the router motherboard: Step 1 Pull the latches away from the DIMM at both ends. This lifts the DIMM slightly.
Appendix C Installing and Upgrading Memory and Virtual Private Network Modules Installing and Removing a DIMM Step 2 Place the DIMM in an antistatic bag to protect it from ESD damage. Installing a DIMM Caution Do not insert DIMMs into the same connector more than 25 times. Overuse can damage the connector. To install a DIMM, follow these steps: Step 1 Make sure that both latches on the DIMM connector are open.
Appendix C Installing and Upgrading Memory and Virtual Private Network Modules Installing a VPN Module Installing a VPN Module Caution To support the VPN module on the Cisco 815 integrated services router, the router must have Cisco advanced IP services IOS software and 128 MB of DRAM installed. Follow these steps to install a VPN module: Step 1 Figure C-6 Installing the Standoffs on the VPN Module Standoff Screw Standoff is installed into the hole just behind the large connector.
Appendix C Installing and Upgrading Memory and Virtual Private Network Modules Installing a VPN Module Step 2 VPN Module Location 65823 Figure C-7 Locate the VPN module slot, and insert the VPN module, as shown in Figure C-7. Step 3 Seating the VPN Module 65824 Figure C-8 Pushing down as indicated in Figure C-8, plug the VPN module into the slot.
Appendix C Installing and Upgrading Memory and Virtual Private Network Modules Installing a VPN Module Step 4 To secure the VPN board connection in the socket, you must attach a retention clip. a. Retention Clip Location 29970 Figure C-9 The retention clip for the Cisco 815 integrated services router slides over the VPN module where it connects to the socket and clips to the side of the router motherboard. The horizontal tab slides underneath the WIC 0 socket, as shown in Figure C-9.
Appendix C Installing and Upgrading Memory and Virtual Private Network Modules Installing a VPN Module Aligning the Retention Clip Center Post 29971 Figure C-10 Align the post with the hole in the board c. Attach the retention clip to the motherboard, as shown in Figure C-11.
Appendix C Installing and Upgrading Memory and Virtual Private Network Modules Installing a VPN Module Attaching the Retention Clip to the Motherboard 29972 Figure C-11 Pull the snap over the edge of the board Cisco 815 Integrated Services Router Hardware Installation Guide OL-9558-01 C-11
Appendix C Installing and Upgrading Memory and Virtual Private Network Modules Installing a VPN Module Step 5 Turn the motherboard over, so that it is resting on its top. Use a Phillips screwdriver to attach the standoffs to the motherboard by using the screws provided, as shown in Figure C-12.
Appendix C Installing and Upgrading Memory and Virtual Private Network Modules Closing the Chassis Closing the Chassis After installing memory or a VPN module on the motherboard, attach the router cover by following these steps: Step 1 If you disconnected the fan from the motherboard in the “Opening the Chassis” procedure, reconnect the fan cable to the connector labeled FAN on the motherboard.
Appendix C Installing and Upgrading Memory and Virtual Private Network Modules Closing the Chassis Attaching the Router Cover 12616 Figure C-13 Step 4 Using a number one Phillips screwdriver, replace the screws that you removed when you opened the chassis. (See Figure C-1.
INDEX Numerics C 100 LED 1-6 cables console B-3 Ethernet pinout B-1 A requirements for Ethernet networks B-2 auxiliary port connecting 2-9 caution, definition xi chassis description 1-2, 1-5 closing C-13 illustration 1-4 dimensions A-1 opening C-2 Cisco reseller, contacting 3-1 B closing chassis C-13 back panel connectors command conventions xviii to xix commands description 1-5 config-register 3-6 illustration 1-4 configure terminal 3-6 LEDs copy 3-5, 3-6 description 1-6 enable 3-5
Index determining value 3-2 to 3-3 enable secret command 3-6 resetting 3-6 to 3-7 enable secret password, resetting 3-6 configure terminal command 3-6 ETH ACT LED 1-8 connecting ETH COL LED 1-8 Ethernet cable 2-2 Ethernet cable power cord 2-5 connecting 2-2 router to a PC 2-7 pinouts B-1 console port requirements for networks B-2 connecting 2-7 Ethernet port description 1-2, 1-5 connecting 2-2, 2-3 illustration 1-4 description 1-2, 1-5 specifications A-1 illustration 1-4 conventions
Index show version command 1-9 I modem installing connecting to router 2-9 DIMM C-4 preparing for 2-1 support 1-2 MOD OK LED 1-6 stacking with other devices 2-10 verifying using LEDs 2-6 VPN C-7 to C-12 N note, definition xi NVRAM 1-8 L LEDs back panel 1-4 front panel 1-7, 1-10 O OK LED OK LED diagnostics 3-7 description 1-7 using to verify installation 2-6 diagnostics 3-7 LINK LED 1-6 opening chassis C-2 M P memory password, recovering 3-2 description 1-8 DIMM installing C-4 locating o
Index illustration 1-4 password recovery 3-2 specifications A-1 using the OK LED 3-7 problem solving 3-7 WAN interface cards 3-8 to 3-9 PWR LED 1-7 U R unpacking the router 1-10 reset command 3-4 resetting the router 3-4 to 3-5 router resetting 3-4 to 3-5 V VPN module specifications A-2 installing C-7 to C-12 unpacking 1-10 location on router C-8 S W show startup-config command 3-5 WAN interface cards show version command 3-3 router slots 1-2 specifications, operating A-2 slot specifi