System Manual
Table Of Contents
- Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
- Preface
- Product Overview
- General Description
- Cisco 860 Series ISRs
- Cisco 860VAE Series ISRs
- Cisco 880 Series ISRs
- Cisco 890 Series ISRs
- Hardware Features
- Installing the Router
- Connecting the Router
- Preparing to Connect the Router
- Connecting a PC, Server, or Workstation
- Connecting a Phone
- Connecting an External Ethernet Switch
- Connecting the V.92 modem Port
- Connecting a Terminal or PC to the Console Port
- Connecting a Modem to the Auxiliary Port
- Connecting the 3G Card
- Installing the 3G Adapter for Extended Cable/Antenna
- Connecting a Data BRI Port
- Connecting an FE Line to an FE WAN Port
- Connecting an GE Line to an GE WAN Port
- Connecting an xDSL Line
- Connecting Power over Ethernet
- Connecting the AC Adapter
- Connecting an FXS Line
- Connecting an FXO Line
- Connecting a Voice ISDN BRI Line
- Connecting a Small-form-factor Pluggable Module
- Verifying Connections
- Initial Configuration
- Technical Specifications
- Router Specifications
- Wireless Access Point
- FE and GE Port Pinouts
- Console and Auxiliary Port Connector Pinouts
- FXS and FXO Port Connector Pinouts
- VDSL2 Port Connector Pinouts
- ADSL2+ Port Connector Pinouts
- V.92 Port Connector Pinouts
- G.SHDSL Port Connector Pinouts
- Data BRI Port Connector Pinouts
- Voice ISDN BRI Interface Pin Numbers and Functions
- SFP Port Connector Pinouts
- Cable Specifications
1-22
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-07
Chapter 1 Product Overview
Hardware Features
The LEDs are located on the front panel of the router. Table 1-5 describes the LEDs for the Cisco
866VAE, Cisco 867VAE, Cisco 866VAE-K9, and Cisco 867VAE-K9 ISRs.
SFP
12
EN Off Not present. — — 892F
models
Green Present and enabled. — —
Amber Present with failure. — —
SFP S Green Blinking—Blinking frequency indicates port speed. — — 892F
models
1. SSID = service set identifier.
2. LWAPP = Lightweight Access Point Protocol.
3. PPP = Point-to-Point Protocol.
4. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line) and VDSL (very-high-data-rate digital
subscriber line).
5. DSLAM = digital subscriber line access multiplexer.
6. 3G = Third-Generation.
7. WWAN = wireless WAN.
8. RSSI = Received Signal Strength Indicator.
9. GSM = Global System for Mobile Communication.
10. CDMA = code division multiple access.
11. SRST = Survivable Remote Site Telephony.
12. SFP = small-form-factor pluggable.
Table 1-4 LED Des criptio ns fo r the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)
LED Color Description 860 Series 880 Series 890 Series
Table 1-5 LED Descriptions for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and Cisco 867VAE-K9 ISRs
LED Activity Description
Power/System Power/System LED: Solid
GE_MODE LED: Off
DSL_LINK LED: Off
Power is on and system running in the Rommon mode.
Note
During the early booting stage, both Power/System, GE_MODE and
DSL_LINK LED will be turned on temporarily for the power on test.
DSL_LINK and GE_MODE LED will be turned off later after booting
into Rommon.
Power/System LED: Solid
GE_MODE LED: Solid
DSL_LINK LED: Off
IOS functioning in GE WAN mode.
Power/System LED: Solid
GE_MODE LED: Off
DSL_LINK LED: Solid or
flashing
IOS functioning in DSL_WAN mode.
Note
In IOS DSL_WAN mode, DSL_LINK LED will be solid after DSL
training complete or flashing during training.
xDSL
1
ACT Green On—DSL interface is up.
Blinking—DSL WAN activity (traffic in either direction).
Faster blinking—Heavier traffic
Off—Device is powered off or the DSL WAN interface is down.