System Manual
Table Of Contents
- Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
- Preface
- Product Overview
- General Description
- Cisco 860 Series ISRs
- Cisco 860VAE Series ISRs
- Cisco 880 Series ISRs
- Cisco 890 Series ISRs
- Hardware Features
- Installing the Router
- Connecting the Router
- Preparing to Connect the Router
- Connecting a PC, Server, or Workstation
- Connecting a Phone
- Connecting an External Ethernet Switch
- Connecting the V.92 modem Port
- Connecting a Terminal or PC to the Console Port
- Connecting a Modem to the Auxiliary Port
- Connecting the 3G Card
- Installing the 3G Adapter for Extended Cable/Antenna
- Connecting a Data BRI Port
- Connecting an FE Line to an FE WAN Port
- Connecting an GE Line to an GE WAN Port
- Connecting an xDSL Line
- Connecting Power over Ethernet
- Connecting the AC Adapter
- Connecting an FXS Line
- Connecting an FXO Line
- Connecting a Voice ISDN BRI Line
- Connecting a Small-form-factor Pluggable Module
- Verifying Connections
- Initial Configuration
- Technical Specifications
- Router Specifications
- Wireless Access Point
- FE and GE Port Pinouts
- Console and Auxiliary Port Connector Pinouts
- FXS and FXO Port Connector Pinouts
- VDSL2 Port Connector Pinouts
- ADSL2+ Port Connector Pinouts
- V.92 Port Connector Pinouts
- G.SHDSL Port Connector Pinouts
- Data BRI Port Connector Pinouts
- Voice ISDN BRI Interface Pin Numbers and Functions
- SFP Port Connector Pinouts
- Cable Specifications
1-26
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-07
Chapter 1 Product Overview
Hardware Features
The Cisco 88xG models come with a 34-mm express card slot ready for use with a commercial 3G card
radio. The 3G express card slot is located on the front panel. For a list of supported 3G cards, see the
Cisco 880 Series Integrated Services Routers data sheet.
Wireless LAN Connectivity
The embedded Wi-Fi CERTIFIED™, 802.11a/b/g/n-compliant wireless AP is preinstalled in the router
as an optional feature. The Cisco 860 series routers support autonomous features and network
configurations. The Cisco
880 series and 890 series routers support both autonomous and unified
features and network configurations.
The wireless AP does not have an external console port. Use the router’s console port as described in
Chapter 3, “Connecting a Terminal or PC to the Console Port.” To configure the wireless device, use the
Cisco IOS command-line interface (CLI).
Table 1-8 describes the radios and antennas for the Cisco 860 series, 880 series, and 890 series routers.
Note
Cisco 860VAE ISRs do not support wireless LAN connectivity.
The 5-GHz radio operates in the Unlicensed National Information Infrastructure (UNII) 1, 2, 3, 5-GHz
frequency bands.
Table 1-8 Wireless Device Radios and Antennas
Radio Module Platform
Radio
Band
Maximum Data
Throughput
1
1. Actual data rate is highly dependent on your wireless environment.
Mode Antenna
Single-band
802.11b/g/n
draft 2.0 radio
module
Cisco 860 and 880 series
routers
Note
Cisco 860VAE
ISRs do not
support wireless
LAN connectivity.
2.4 GHz Up to 100 Mb/s Cisco 860 series:
autonomous only
Cisco 880 series:
autonomous and
unified
Three captive 2-dBi
omnidirectional dipole
antennas
Dual-band
simultaneous
802.11a/n and
802.11b/g/n
radio module
Cisco 890 2.4 GHz
and 5 GHz
100 Mb/s per radio,
up to 200 Mb/s
total
Autonomous and
unified
Three dual-band,
removable,
2.4-GHz/5-GHz
omnidirectional dipole
RP-TNC antenna
2
2. The antennas require some minor installation. They must be screwed onto the RP-TNC antenna connectors on the I/O side of the chassis. See the following
document on Cisco.com for feature information:
.http://www.cisco.com/en/US/docs/routers/access/wireless/hardware/notes/antdip.html