System Manual
Table Of Contents
- Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
- Preface
- Product Overview
- General Description
- Cisco 860 Series ISRs
- Cisco 860VAE Series ISRs
- Cisco 880 Series ISRs
- Cisco 890 Series ISRs
- Hardware Features
- Installing the Router
- Connecting the Router
- Preparing to Connect the Router
- Connecting a PC, Server, or Workstation
- Connecting a Phone
- Connecting an External Ethernet Switch
- Connecting the V.92 modem Port
- Connecting a Terminal or PC to the Console Port
- Connecting a Modem to the Auxiliary Port
- Connecting the 3G Card
- Installing the 3G Adapter for Extended Cable/Antenna
- Connecting a Data BRI Port
- Connecting an FE Line to an FE WAN Port
- Connecting an GE Line to an GE WAN Port
- Connecting an xDSL Line
- Connecting Power over Ethernet
- Connecting the AC Adapter
- Connecting an FXS Line
- Connecting an FXO Line
- Connecting a Voice ISDN BRI Line
- Connecting a Small-form-factor Pluggable Module
- Verifying Connections
- Initial Configuration
- Technical Specifications
- Router Specifications
- Wireless Access Point
- FE and GE Port Pinouts
- Console and Auxiliary Port Connector Pinouts
- FXS and FXO Port Connector Pinouts
- VDSL2 Port Connector Pinouts
- ADSL2+ Port Connector Pinouts
- V.92 Port Connector Pinouts
- G.SHDSL Port Connector Pinouts
- Data BRI Port Connector Pinouts
- Voice ISDN BRI Interface Pin Numbers and Functions
- SFP Port Connector Pinouts
- Cable Specifications
2-3
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16193-07
Chapter 2 Installing the Router
Installing the Router
Connections
Obtain a broadband or Ethernet connection from your service provider.
Ethernet Devices
Identify the Ethernet devices that you will connect to the router: hub, servers, and workstations or PCs.
Ensure that each device has a network interface card (NIC) for connecting to Ethernet ports.
•
If you plan to configure the software using Cisco IOS commands through the console port, provide
an ASCII terminal or a PC that is running terminal emulation software to connect to the console port.
•
If you plan to connect a modem, provide the modem and modem cable.
•
If you plan to use the Data BRI port, provide an NT1 device and an ISDN S/T cable.
•
If you plan to use the cable-lock feature, provide a Kensington or equivalent locking cable.
Installing the Router
This section describes how to install the Cisco 860 series, 880 series, and 890 series ISRs. These routers
can either be installed on a table top or other flat horizontal surface or be mounted on a wall. The
Cisco
890 series ISRs may be mounted in a rack. This section also describes how to attach WLAN
antennas to the Cisco
890 series routers. This section contains the following topics:
•
Warnings, page 2-3
•
Installing Antennas, page 2-4
•
Installing on a Table, page 2-7
•
Mounting on a Wall, page 2-7
•
Installing in a Rack, page 2-10
•
Installing the Router Ground Connection, page 2-11
Warnings
Warning
This equipment needs to be grounded. Use a green and yellow 12 to 14 AWG ground wire to
connect the host to earth ground during normal use.
Statement 242
Warning
This equipment must be grounded. Never defeat the ground conductor or operate the equipment
in the absence of a suitably installed ground conductor. Contact the appropriate electrical
inspection authority or an electrician if you are uncertain that suitable grounding is available.
Statement 1024